Previously, if a mag was not required (not index 0 and not used by ekf),
it was not counted in num_enabled_and_valid_calibration.
If a user set SYS_HAS_MAG to e.g. 3, it would then trigger a preflight
failure, even if there were 3 calibrated and enabled mags.
The EKF can recover from an initial bad earth mag field estimate.
Constraining the field is not necessary and can lead to an unpredicted
behavior of the filter.
Declination fusion is safe to run even when the horizontal field is 0
On slowly moving vehicles (e.g.: boats, rovers), the yaw estimator has
worse convergence than the main EKF. Resetting the mag states using the
yaw estimator as reference can lead to poor heading. Also, the EKF can
recover really well from initially incorrect mag states.
The previous default of 900m leads to many warnings if left
unchanged, especially if the vehicle is already in-air when
the Mission is started.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Includes:
- Remove some of the outdated Python2 checks and compatibility.
- Try not catch all exceptions but only the expected ones. Otherwise,
this makes it really hard to debug if anything unexpected actually
goes wrong.
- Make use of fstrings.
- Make output slightly prettier.
Signed-off-by: Julian Oes <julian@oes.ch>
This adds a new protocol extension which allows to get the bootloader
version.
The bootloader version is different from the bootloader protocol
revision which has stabilized at 5 and is not easy to update unless a
bootloader is actually breaking the protocol. The reason being that both
the Python script as well as the uploader used in QGC will not attempt
to load firmware if they don't know the bootloader version, so it could
basically be considered a "breaking" protocol revision.
Signed-off-by: Julian Oes <julian@oes.ch>
If the STM32H7 fails to program or erase a full chunk of 256 bytes, the
ECC check will trigger a busfault when trying to read from it.
To speed up erasing and optimize wear, we read before erasing to check
if it actually needs erasing. That's when a busfault happens and the
erase time outs.
The workaround is to add an option to do a full erase without check.
Credit goes to:
https://github.com/ArduPilot/ardupilot/pull/22090
And the protocol option added to the bootloader is the same as for
ArduPilot, so compatible.
Signed-off-by: Julian Oes <julian@oes.ch>
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
- increase symforce CppConfig zero_initialization_sparsity_threshold so
that a Matrix setZero() call is performed instead of individually zeroing
Co-authored-by: bresch <brescianimathieu@gmail.com>
The setting wasn't consistent with the one used in the Visual Studio
Code settings, which caused different newline formatting depending on
whether the user uses Visual Studio Code or another editor that uses
EditorConfig.
This notes the reference yaw angle for the Septentrio Mosaic-H.
It's unfortunately a bit tricky in that Unicore has the main antenna
in front by default while Septentrio decided to put the aux antenna in
front.
Signed-off-by: Julian Oes <julian@oes.ch>
Regression from https://github.com/PX4/PX4-Autopilot/pull/23043
Also avoids a race condition by making sure the command ack is handled
before sending out the mavlink message (in case an external component
reacts immediately to the mavlink message).
- this warning was to catch any potential errors in sensor selection
relative to what's actually available, we don't need to complain
about initial selection before the EKF selector is available
When North-East (e.g.: GNSS pos/vel) aiding is active, the heading
estimate is constrained and consistent with the vel/pos aiding. Reset to
GNSS heading should only occur if no N-E aiding is active or if the
filter is not yes aligned. Otherwise, just wait for the consistency
check to pass again (will pass at some point if the heading uncertainty
of the filter is getting too high).
- topic update was checked twice in the same loop and thus
the second time the topic would never indicate to have updated
Co-authored-by: RomanBapst <bapstroman@gmail.com>
- warn about full traffic conflict buffer at 1/60hz.
- add conflict expiry for buffer.
- use only events for buffer full warning. mavlink_log_critical no longer needed.
- use icao address for conflict warnings id, stop using uas_id. UTM_GLOBAL_POSITION assumed deprecated.
- stop spamming when buffer is full
- fix warning wording if buffer is full.
- remove UTM_GLOBAL_POSITION
Fixes failing unit test:
* [adsbTest] Reduce conflict timestamps - not enough time has passed in ci
- failed ci output - (passes locally with make tests TESTFILTER=AdsbConflict)
- Timestamp: 6000000000
- Time now: 457720038
- Time since timestamp: 0
- Old Conflict warning expired: 0
- --------------------
- adsb_conflict._traffic_state 0
- ../../src/lib/adsb/AdsbConflictTest.cpp:244: Failure
- Value of: adsb_conflict._traffic_state == TRAFFIC_STATE::REMIND_CONFLICT
- Actual: false
- Expected: true
* Made Serial API open the UART in NON BLOCKING mode
* Updated voxl_esc driver to latest from ModalAI fork
* Ported voxl_esc driver over to new Serial UART API
* Removed voxl_esc serial abstraction since new Serial API is already a serial abstraction
- with the addition of the navsat plugin in PR#22638, the callback would
reassign the previous timestamp used in the calculations of the
angular_velocity causing derivative type noise in the groundtruth
measurements
This is a minimal change to make it harder to crash a
vehicle with an empty battery if the capacity was set wrong.
The disadvantage is that the state of charge estimate will
fluctuate more under load.
We need better documentation and improvements to the estimation.
The existing disarmed logic already handles disabled outputs
it makes sense to reuse it and not have lockdown handled
differently resulting in unexpeced corner cases.
This removes the duplication with unexpected differences
and allows to consistently handle the output instead of
overriding the output for some specific cases which
leads to unexpected corner cases. E.g. disabled outputs
suddenly outputing PWM in lockdown.
In HITL the actuators should not be mapped
and they are in lockdown.
We should not reconfigure disarmed, min, max PWM values
without updating the actual output values because the IO
will consider the last outputs before the FMU was rebooted
with the configuration of the new boot. This can result
in spinning motors when switching to SIH.
For Septententrino we seem to sometimes fill the buffer pretty full.
If we ask for too much, readAtLeast will fail completely and make the
GPS discovery logic fall over. Therefore, let's not ask for too much and
just read what we can given the available buffer.
Signed-off-by: Julian Oes <julian@oes.ch>
* Added decoy termios support to Qurt so that ghst parser in RC library can be used. No termios is actually needed but has to be there for the parser to work
- Added an empty constructor, setPort, and validatePort functions for Serial API
- Changed GPS to not allocate Serial object dynamically
- Moved access check on serial port name into the Serial API
- Improved the Qurt platform validatePort Serial function to implement a more rigorous check. Added safety check
to the setPort Serial function to make sure it isn't called after the port has been already opened.
This matters for PWM when the last output gets disabled on either FMU or IO
it would just keep on running.
Also when rebooting with a parameters reset or new airframe with no mapped outputs
it would previously keep outputting PWM with the disarmed value of the new airframe
e.g. 1000us which is a safety hazard because servos could break the physical limit of the
model or miscalibrated ESCs spinning motors.
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
- Added offset to Posix hrt time to account for synchronization with Qurt hrt time
- Added new Kconfig to configure synchronization of HRT timestamps on VOXL2
- Moved voxl2 libfc sensor library submodule from muorb module to boards directory
- Added check to make sure hrt_elapsed_time can never be negative
EditorConfig is a well-known convention to share style settings across
different editors. Adding one will make it easier for new contributors
or people who like to use a different editor to contribute.
The duration of a unit test had to be increased because the incorrect
covariance matrix update, was making the unit test passing faster
(over-optimistic variance).
Using full 3D acceleration provides better horizontal acceleration
tracking but also creates a sometimes unwanted behavior because the tilt
is directly coupled with the vertical acceleration setpoint.
* Commander: make low remaining flight time configurable and do not clear
- add _ACT param to disable/warning/RTL this feature
- publish rtl flight time estimate also in RTL, and thus fix re-validation
- make failure message clearer, distinguish from battery low
* battery check: add hysteresis for declaring battery_low_remaining_time false again
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: KonradRudin <98741601+KonradRudin@users.noreply.github.com>
The voxl2 has a split architecture. PX4 runs on a posix platform and a Qurt platform. The two communicate uorb topics back and forth with the muorb module. But each has it's own parameters database and they need to stay in sync with each other. This PR adds support to keep the 2 parameter databases in sync. The main parameters database running on Linux has file system support while the Qurt one does not. The Linux side is considered the primary and the Qurt side is considered the remote.
We need to make sure that when the RTL is triggered, it should not reevaluate it, as when it was valid but evaluated to false on activation, it can't do a RTL.
Previously uORB queue size was an awkward mix of runtime configurable (at advertise or IOCTL before allocate), but effectively static with all queue size settings (outside of test code) actually coming from the topic declaration (presently ORB_QUEUE_LENGTH in the .msg). This change finally resolves the inconsistency making the queue size fully static.
Additionally there were some corner cases that the muorb and orb communicator implementation were not correctly handling. This PR provides fixes for those issues. Also correctly sets remote queue lengths now based on the topic definitions.
* Made setting of uORB topic queue size in based on topic definition only
* Fixes to the ModalAI muorb implementation
* Removed libfc sensor from format checks
* msg/TransponderReport.msg ORB_QUEUE_LENGTH 8->16 (was set to higher in AdsbConflict.h
---------
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Daniel Agar <daniel@agar.ca>
Remove option to track from previous wp to reduce complexity and fix
case where prev=current point and the line following broke down.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
We had a special handling for RTL triggered in vtol_takeoff state.
The idea is to wait until the VTOL Takeoff is completed and only
then switch to RTL. On a second thought this special handling isn't
really necessary and for the sake of simplicity should be removed.
This also removes the side effect of the indicated flight mode
after RTL being set to VTOL_Takeoff again.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Position Control: some cosmetical changes
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Position Control: disable roll constraining warning in VTOL transition
In transitions it is expected that the roll is constrained, and
instead of defining an aribitrary threshold let's rather disable
the user warning in that case.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Pos C: define magic numbers for roll constraining warning as constants
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The gyro bias estimate from EFK2 is really good when at rest and should
be used by the yaw estimator to prevent heading drifts due to poor
heading observability.
ENOENT returns if the file doesn't exist yet, when using mtd /fs/mtd_net always exist.
On a filesystem you've to generate the file so if ENOENT returns we've to regenerate the default config as well.
The main problem was that during initial negotiation the client would
request the gimbal_manager_information from px4 but px4 would never send
it because in this configuration the device_compid was set to 0.
`estimator_baro_bias` requires to have GNSS and baro hgt active and GNSS as the reference. This is quite restrictive. Instead, we can simply use a high-passed version of the baro error.
* Added Lawnmower airframe
* Update 5005_gz_lawnmower
Works all right
* Update 5005_gz_lawnmower
RDD_WHL_SPEED has new name: RDD_WHEEL_SPEED
* Update ROMFS/px4fmu_common/init.d-posix/airframes/5005_gz_lawnmower
Co-authored-by: Per Frivik <94360401+PerFrivik@users.noreply.github.com>
* Update ROMFS/px4fmu_common/init.d-posix/airframes/CMakeLists.txt
Co-authored-by: Per Frivik <94360401+PerFrivik@users.noreply.github.com>
* Renamed 5005_gz_lawnmower to 4011_gz_lawnmower
also pulled latest GZ models hash
---------
Co-authored-by: Per Frivik <94360401+PerFrivik@users.noreply.github.com>
This is a workaround to hotfix CI but the root cause is #22792
(MAVSDK test failing after EKF change, accelerometer simulation issues not learned anymore?)
MissionBase did not initialize its mission data, thus could enter an
infinite loop in updateDatamanCache() if the initMission() failed to
read the mission off, for example, due to the SDCard storage task taking
longer than the timeout to respond.
This change constrains the loading loop and resets the mission data even
if the data write failed.
The setpoint.yaw can be NAN, and this made the calculated land point NAN
as well. Looking at the current yaw is anyway a better way to approximate
the course over ground that fundamentally should be used.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
ADd a new misison feasiblity checker option to check if a proper landing approach is defined when in air. There must be at least a mission landing or a VTOL approach defined in order for the mission to be accepted. Else, use the same logic as in MIS_TKO_LAND_REQ=4
* publish the global groundtruth from the navsat callback and rearrange the local groundtruth as the altitude reference now has a dependency on the global groundtruth being initialized
---------
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
-remove RTL_HDG_MD
-only set heading setpoint in Navigator::RTL once above landing point,
or when RTL is triggered close to it
-never set a heading during RTL if weather vane is enabled
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
After smoothing the linera velocity setpoint, the EKF has trouble initializing, becuase the acceleration is too smooth, to combat this issue, there is a 1 second delay when initializing the mission mode
Instead of directly setting the attitude setpoint for usage inside the same module
only publish it to the uorb topic, which is subscribed to in the same module.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* battery: make time remaining estimation dependent on level flight characteristis for FW
* battery: fix that FW flight is also correctly detected when vehicle_status is not updated
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FixedwingPositionControl: Move constant to header file
* flight phase estimation: use tecs height rate reference to check for level flight
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
When flow control is used together with DMA, we need to add a pulldown
to CTS. Without it, it assumes flow control and gets stuck when
CTS is not connected.
Signed-off-by: Julian Oes <julian@oes.ch>
When the CPU load monitor is started while already running, then the
idle thread last_times[0] is reset to the last 1 second, rather than
since when the CPU load monitor was last started. The remaining threads
are not impacted, since their last_times[i] is reset to zero here.
This results in the idle thread having a lower than real CPU load, with
the remaining CPU time being wrongly attributed as scheduler load.
The ADC peripheral can only support up to
50MHz on rev V silicon and 36MHz on Y silicon.
The existing driver always used no prescaler
and kept boost setting at 0.
* refactor driver to dynamically check registers and do reset if register does not match desired value
* have seen various times where shunt calibration was reset in air
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* avoid waypoint following during backtransition
- if vehicle overshoots transition, make controller track the prev/current
waypoint line, this avoids large banking maneuvers that delay the transition further
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* navigator: use SETPOINT_TYPE_LAND as setpoint type for VTOL_LAND waypoints
such that fixed wing position controller can distinguish from other types
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* FixedWingPositionControl: split vtol backtransition logic into separate method
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* review changes
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* prevent loiter when approaching vtol backtransition and invalidate previous waypoint during mission landing
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* removed unused parameter
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* small renaming of transition mode
Signed-off-by: RomanBapst <bapstroman@gmail.com>
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
When a state stops to be estimated it becomes a "consider state". Its value and variance are frozen but its covariance with other states continue to evolve normally.
- removes conservative accel bias variance limiting
- force symmetry is skipped after fusion of NED vel/pos (a direct measurement)
---------
Co-authored-by: bresch <brescianimathieu@gmail.com>
When handling multiple commands, it could happen that the first command
updates _reposition_triplet. Normally this would then get handled after
getting the mode change from commander through vehicle_status.
But if the next command is handled before an update from commander, it
could overwrite the triplet.
This patch ensures that navigator waits for an update from commander (and
therefore process the _reposition_triplet) before handling the next
command.
This happened specifically when pressing 'Pause' from QGC during a mission.
QGC sends VEHICLE_CMD_DO_REPOSITION twice, first for pausing, then changing
the altitude.
The result was that the vehicle would not stop at the current location but
continue to the next mission waypoint and stop there.
- fake_pos only if at rest or tilt variances becomes large
- fake pos: don't run when grav fusion is enabled
- gravity fusion enabled by default
- gravity: only fuse when accel norm and lpf norm are consistent
Co-authored-by: bresch <brescianimathieu@gmail.com>
A board can optionaly define RC_SERIAL_SWAP_USING_SINGLEWIRE
If the board is wired board with TX to the input (Swapped) and
the SoC does not support U[S]ART level RX-TX swapping to allow
useing onewire to do the swap if and only if:
RC_SERIAL_SWAP_USING_SINGLEWIRE is defined
RC_SERIAL_SWAP_RXTX is defined
TIOCSSWAP is defined and retuns !OK
TIOCSSINGLEWIRE is defined
* TECS: reduce default of FW_T_I_GAIN_THR
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* TECS: reduce default of FW_T_THR_DAMP
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* TECS: improve param descriptions and meta data of some params
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Pos C: rename FW_T_THR_DAMP to FW_T_THR_DAMPING
Rename wihtout param translation as the interpretation of this param has changed
recently (a bug was fixed that caused the damping to have a much lower effect than
it should). We want to avoid that users keep the previously tuned value (with the bug)
and do not update the tuning when using the fixed version (v1.14.0 and later).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Pos C: rename FW_T_I_GAIN_THR to FW_T_THR_INTEG
Rename wihtout param translation as the interpretation of this param has changed
recently (a bug was fixed that caused the damping to have a much lower effect than
it should). We want to avoid that users keep the previously tuned value (with the bug)
and do not update the tuning when using the fixed version (v1.14.0 and later).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This check gave a warning when one or more mission items were below the
Home altitude. As it is a valid usecase to plan missions below Home,
those warnings were too often seen as a inconvenience and are thus
removed here.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
That enables us to update the pitch setpoint in Stabilized mode
in the VTOL controller (pitch ramp for transition).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Separate offboard path setpoints as fixedwing pos control state
This commit separates offboard path following as a separate state inside the FW Poscontrol module.
This is a cleanup on clearly defining fw pos control behaviors
* Update src/modules/fw_pos_control/FixedwingPositionControl.cpp
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
* Fix format
---------
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
The IMU topic is not zeroed, and the clipping information was not
copied, so this field ended up being garbage.
Signed-off-by: Julian Oes <julian@oes.ch>
With this margin it is made sure that if the loiter is not perfectly tracked,
(vehicle outside of path setpoint) a wp just at the border of the loiter
is still reachable.
It should though be as small as necessary, as otherwise, with good
loiter tracking, waypoints that are close but not right on the loiter
radius are not enforcing the exit course neither.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* PositionSetpoint: remove yaw_valid field
* Navigator: set yaw setpoint to NAN for Takeoff
Don't set a yaw setpoint for takeoff, as Navigator doesn't handle the yaw reset.
The yaw setpoint generation is handled by FlightTaskAuto.
* PositionSetpoint.msg: remove disable_weather_vane and instead only use the yaw field
Strictly follow the concept that if the position_setpoint.yaw is set, then
follow it the controller, and otherwise let the controller set it as it
thinks it's best.
* Navigator: remove logic that sets yaw to be accepted in TAKEOFF
No longer needed as during Takeoff we anyway don't set a yaw setpoint.
* PositionSetpoint.msg: remove yawspeed_valid
* PositionSetpoint.msg: remove yawspeed
* Navigator: set yaw setpoint to NAN instead of current
In set_takeoff and set_land_item, as well as for VTOL transition.
The flight tasks then set the yaw corresponding to the current yaw.
* Navigator: change get_yaw_acceptance into a bool
* PositionSetpoint.msg: improve comment for yaw
* MissionBlock: remove unnecessary code from set_vtol_transition_item
* Navigator: clean up calculate_breaking_stop(), set yaw to NAN
* Navigator: set yaw to NAN in variouls places where not specifc setpoint is desired
* Navigator: set yaw to NAN in reset_position_setpoint()
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
1s gives some false positives at boot up, as the airspeed selector only
starts publishing 2s after its startup.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
-remove dedicated vtol transition airspeed init logic
-init airspeed setpoint on first usage of tecs
-init to max of current airspeed and min airspeed
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
simulation gazebo: move the gazebo models to submodule, allow for operation with external gazebo instance, independent of startup order. Allows drag an drop of models from gazebo fuel.
* rolled back updates
Signed-off-by: frederik <frederik@auterion.com>
* fixing empy
Signed-off-by: frederik <frederik@auterion.com>
* Update GZBridge.cpp to lower drop position
Dropping from 1m leads to movement in the rc_cessna. Dropping from 0.5m leads to no movement.
* Update STANDALONE env variable.
* Update STANDALONE env_variable on GZBridge
* Update src/modules/simulation/gz_bridge/GZBridge.cpp
Co-authored-by: Daniel Agar <daniel@agar.ca>
* test removal of x500
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* removed all models and reworked logic
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* remove model path in set_sdf_filename
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* filter resource path for world sdf
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* updated structure to keep old make px4_sitl
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* remove gz tools
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* import gz as submodule and reverse rc simulator logic
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
* [gz-sim]: source GZ_SIM_RESOURCE_PATH only if PX4 starts gz server
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
* Typo fix
---------
Signed-off-by: frederik <frederik@auterion.com>
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
* events: pass relative paths plus base path to source parser script
to work around maximum Makefile command lenght limits.
* events: correct cmake comment typo
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
---------
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
The _control_mode_current wasn't updated otherwise, and only done so by luck
because we already set the current type to SETPOINT_TYPE_POSITION.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- double required max consecutive counts
- don't continuously complain about round trip time (RTT) unless
there's been at least one acceptable round trip (latency < 100 ms)
Before this fix, the time_utc_usec output from blending was always 0.
This means that you wouldn't get a valid vehicle_gps_position/time_utc_usec
With this commit, UTC timestamps are blended according to weights for
all GPSes with a nonzero UTC timestamp value.
It would be possible to simply use the first valid UTC timestamp instead
of blending, but since the system timestamps are blended, it seems
suitable to blend UTC timestamps as well.
- This fixes the force call on SensorSelectionUpdate
- In contrary to the rest of the codebase, this method also takes a timestamp: When you call SensorSelectionUpdate(true), time_now_us is actually set to 1 and force stays false, as this is the default value for in the method.
wait_until_altitude() checks for absolute altitude being
close so checking for 1m below the setpoint can fail
if the speedup results in no sample inside the altitude
window being checked.
Ideally the test could check if the takeoff is done directly
instead of comparing altitudes in the first place.
-remove external init, and instead always (but only) init when dt is too large
-init the controller params correctly
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The control params (eg min/max pitch) are used before they are
correctly set by TECS::update(). While this is an issue we should fix,
it also doesn't hurt to set them to more reasobale values (eg 30° limit).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
As discussed in the maintainer call we should adhere to the
parameter naming scheme that makes it clear what vehicle type the
configuration is good for.
by only applying the sqrt linear drag when brakeing.
It was originally not done this way to avoid discontinuities and
the exact speed bewlo 1m/s didn't matter. With the position slow mode
the exact slow speeds now matter. And the discontinuities are avoided by
reusing the brake boost filter.
It is generally preferred to have the camera pointing forward on pause,
e.g. to use the camera for Navigation.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The velocity smoothing library constrains the maximum vellocity.
I set the default constraint to 0 to find these exact issues.
The heading smoothing did not initialize the maximum velocity
which in this use case is the maximum heading.
So heading was always constrained to 0 -> north until this change.
The defintion of the custom symbol M_PI_PRECISE
was not included in one of the only places it's used.
Looks like a mistake that happened in
34c852255e
possibly because a lot of things are included
almost everywhere and if the include order
ligns up there are no compile errors.
Note that the unit test also passes without
thechange. But the VelocitySmoothing's
local_time would get NAN. This would leads to
wrong trajectory calculations.
Problem: Zero maximum jerk and/or zero
direction would lead to divisions by zero in
various cases depending on the exact configuration and code path.
Solution: There was already one check for the
direction being zero in one path and I
summarized to check in both
updateDurations...() functions the product
of direction * max_jerk to not be zero
because that's exactly the value calculations
devide by.
goto control class handles smoothing of goto setpoints, outputs trajectory setpoint for mc pos control
some minor encapsulation done in mc pos control for readability
new param MPC_YAWAAUTO_MAX limiting heading accelerations in heading smoother
The size input argument for monocypher crypto_xchacha20_ctr should be the
plaintext message length.
The promise of the interface is, that the call to encrypt_data updates the
ciphertext message length after the call succeeds.
The crypto should check that the output buffer length (cipher length) is
large enough to contain the encrypted data.
Fix these issues; these have gone unnoticed for a long time since the interface
has been only used by logger, and passing the same size for both in and out.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The manufacturer uses both naming schemes, RoboClaw more than Roboclaw
but it's always one word and hence I think it's more consistent to name
it the latter.
This adds the ICM42686p as a possible alternative to the existing IMUs.
Apparently, the ICM20689 was never actually used in these boards.
Signed-off-by: Julian Oes <julian@oes.ch>
Otherwise if is set to Offtrack, which in turn leads to weird behavior.
E.g. when triggering Land while flying fast forward, the vehcile doesn't
descned to the land point it keeps getting a velocity setpoint from the
smoother that pushes it away from the land point.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This switches all SENS_EN_INAXXX params to 0 by default and instead uses
the i2c_launcher command.
However, if any one the SENS_EN_INAXXX param is set, it no longer tries
to auto-configure it.
Signed-off-by: Julian Oes <julian@oes.ch>
actuator_motors and actuator_servos subscribers for offboard control
Being subscribers, this does not increase the computational load
over the uxrce_dds brigde
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
New thrust and torque control mode added which replaces the previous
actuator mode,
in this mode the rate controllers are disables, the control allocator
is enabled and the used externally provices
vehicle_thrust_setpoints and vehicle_torque_setpoints.
New direct_actuator mode
In direct_actuator mode the control allocator module does not publish
actuator_motors and actuator_servos messages which must instead be
provided extrernally by the user.
Removed old direct mode.
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
* Added parameter UXRCE_DDS_SYNCC to enable system clock synchronization. Refactored and cleaned up. Only set system time if it's off by more than 5 seconds (same as mavlink and gps).
Only re-evaluate if no longer in GF when flight mode is changed or
Loiter position was changed (eg through goto).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- check if Home would breach it (we do not want to upload GF that
do not allow to return to Home)
- check if the current vehicle position isn't contained in the GF
if armed (as then it would immediately trigger)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- do reporting of breaching in-air only in geofenceCheck
- remove geofence_violation_reason_t
- replace geofence_breached field in GeofenceResult.msg with 3 fields
(one for each GF type: max dist, max alt, custom geofence)
- the warning message after breaching a GF is only done by Commander,
and it's specific to the GF type failure
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Use flow rates instead of integrals in backend. This allows us to delay
the data to the mitpoint integration time and simplifies the code in
general.
Gyro compensation can still be done in EKF2 if needed, but the
flow module normally already appends the correct gyro data to the flow
message.
* created a Performance Model for fixed wing vehicle
- added compensation for maximum climbrate, minimum sinkrate, minimum airspeed and trim airspeed based on weight ratio and air density
- added atmosphere lib to standard atmosphere calculations
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Co-authored-by: Thomas Stastny <thomas.stastny@auterion.com>
- in theory these are helpful to ensure EKF2_HGT_MODE configuration is
consistent with the relevant aid source (GPS, baro, etc), but it can
be a little awkward with users having to fight manual parameter
changes in the right order
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
It was failing occationally with:
14:12:43 CMake Error at CMakeLists.txt:129 (list):
14:12:43 list index: 1 out of range (-1, 0)
14:12:43
14:12:43
14:12:43 CMake Error at CMakeLists.txt:131 (list):
14:12:43 list index: 2 out of range (-1, 0)
14:12:43
14:12:43
14:12:43 CMake Error at CMakeLists.txt:132 (string):
14:12:43 string sub-command REPLACE requires at least four arguments.
14:12:43
14:12:43
14:12:43 -- PX4 version: f513c40d62 (f513c40d62..NOTFOUND)
During a round corner the L1 distance calculation
was only done in 2D and the z-axis coordinate
was directly coming from the next waypoint.
This lead to an unpredictable altitude profile
between two waypoints. Sometimes almost all
altitude difference was already covered during
the turn instead of going diagonally.
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
The UART7 TXDMA services TELEM1 with flow control. If CTS is high, the
transmitting thread will wait on a semaphore, which may block other
threads from acquiring necessary resources to make progress, for
example, preventing MAVLINK instances from transmitting.
This change in NuttX makes the TXDMA acquire the semaphore in a
non-blocking way, preventing this issue.
- add functionality to specify world name for simulation in case name
- add test for triggering an airspeed invalidation in case of pitot blockage
- add test for high wind (ramped up wind over short period) to NOT invalidate airspeed in this case
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Increase wind process noise default (ASPD_WIND_NSD) and gate
(ASPD_TAS_GATE) to be able to catch rapid wind increases with
the internal wind estimator of the airspeed validator.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Trust the beta innovations more compated to the TAS innovations.
That should help with detecting real airspeed failures even with
a dynamic wind estimate (as long as vehicle doesn't fly straight)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Increasing the wind process noise results in a more dynamic
wind estimation, which is capable of catching fast-varying
winds. As wind is used in the lateral guidance it's important
that we don't filter it too much.
Furher the gate of the airspeed fusion is increased, to
reduce the likelihood of airspeed fusion stopping due to
dynamic wind conditions. The airspeed is validated in
the airspeed validator (EKF consumes the validated one).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Reduces flash usage by ~16KB.
- compress formats at build-time into a single string with all formats
- then at runtime iteratively decompress using
https://github.com/atomicobject/heatshrink
- if not in air the accel noise is doubled
- if landed don't init unless GPS velocity is non-negligible
- when inactive continue seeding with EKF gyro bias
- reset yaw estimator if GPS fusion is stopped
Has options *None where the check is disabled, and *Warning, where only a warning is
published (which replaces the high wind warning from the COM_WIND_WARN limit).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* started tiltrotor port
* added advanced plane and changed some parameters on the tiltrotor
* added advanced plane
* removed tiltrotor for clean push
* removed standard vtol old model file
* removing the standard vtol changes from this PR, since it is not part of the advanced plane
* removed advanced plane meshes as they are already found in the rc_cessna
* updating and improving airframe parameters
* updated mesh paths
Signed-off-by: frederik <frederik@auterion.com>
---------
Signed-off-by: frederik <frederik@auterion.com>
Co-authored-by: frederik <frederik@auterion.com>
There is no reason to keep an uncertainty on the origin as it is then
already contained in the local position estimate when GNSS data is fused
in the filter.
The command is sent by a dedicated mavlink command and forwarded to the fixed wing position controller.
The pattern is defined by the radius of the major axis, the radius of the minor axis and the orientation. The pattern is then defined by:
The upper part of the pattern consist of a clockwise circle with radius defined by the minor axis. The center of the circle is defined by the major axis minus the minor axis away from the pattern center.
The lower part of the pattern consist of a counter-clockwise circle with the same definitions as above.
In between, the circles are connected with straight lines in a cross configuration. The lines are always tangetial to the circles.
The orientation rotates the major axis around the NED down axis.
The loitering logic is defined inside its own class used by the fixed wing position control module. It defines which segment (one of the circles or lines) is active and uses the path controller (npfg or l1-control) to determine the desired roll angle.
A feedback mavlink message is send with the executed pattern parameters.
- make it work again
- also supports Kconfig based clk source selection
- adapt to recent changes of default PWM limits
- support outputting in duty-cycle mode
- i2c addr use use hex representation
- revert back to common min/max value & move duty-cycle mode to advanced
We provide a latency measurement in the input capture handler.
However, since the timer was not enabled, none of the counter were
running therefore all counters were zero, thus latency was also zero.
Since the HRT is used to provide a timestamp, the lack of the running
timer was never noticed. After enabling the timer, latency now correctly
shows 9-10 counts.
* Fixed an issue where if the GCC_VER_STR would not contain the right NUTTX_GCC_VERSION, the grep -c command would throw a failure, silently exiting the entire ubuntu.sh setup script
This is a tool that can be used to generate advanced lift drag plugin parameters automatically using AVL. Rather than having to create .avl files yourself, pass them to AVL, read out the correct parameters and place them in the Advanced Lift Drag plugin, this tool will do all that for you and generate a complete advanced_lift_drag plugin sdf containing all necessary parameters for any vehicle. All that is required is to specify what the physical geometries of the vehicle are. The scripts are adaptable enough to support a self-selected number of control surfaces.
---------
Co-authored-by: frederik <frederik@auterion.com>
This switches from the horribly intertwined ringbuffer implementation to
the new VariableLengthRingbuffer implementation.
By ditching the previous implementation, we fix MAVLink message
forwarding, which didn't work reliably. The reason it didn't work is
that multiple mavlink messages could be added but only one of them was
sent out because the buffer didn't keep track of the messages properly
and only read the first one.
Signed-off-by: Julian Oes <julian@oes.ch>
This adds a reusable class for a FIFO ringbuffer that accepts variable
length packets. It is using the Ringbuffer class internally.
Signed-off-by: Julian Oes <julian@oes.ch>
* mission_base: reset inactivation index when user set a new mission index, or mission is reset.
* mission_base: check Climb required always on current mission item
This prevents accidental misconfiguration via I2C if there are
multiple SPI devices on the same bus. The device may hear it's i2c address
and write some register, while there is data transfer ongoing with another
device.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
WorkItemSingleShot::_sem is a signaling semaphore, disable PI for it.
Set CONFIG_DEBUG_ASSERTIONS=y and the kernel panics due to the semaphore
having no holder, disabling PI fixes this.
The head/tail semaphores are not used as lock but rather as resource
counters and thus relate more as signaling semaphores. Disable PI for
them.
I run my code with CONFIG_DEBUG_ASSERTIONS=y and the kernel panics due
to the semaphore having no holder, disabling PI fixes this.
This prevents the mavlink transmit loop from waiting on the module mutex
thus not stopping transmissions when the mutex is already taken.
This can happen when calling `mavlink status` from the mavlink shell,
where `Mavlink::get_status_all_instances()` takes the mutex and then
prints the status via pipes to the mavlink transmit buffer.
If that pipe cannot be emptied a deadlock happens.
Since the MavlinkReceiver thread also waits on the module mutex, both
reception and transmission of Mavlink packets are then prevented thus
disabling communications entirely.
IMUs were replaced in V3 with 2x ICM42688P. This configuration should
work with all revisions of Matek F743 Slim board, including V1, V1.5
and interim variant of V3 (ICM42688P + ICM42605).
Signed-off-by: Andrei Korigodskii <akorigod@gmail.com>
In the lightware_parser function, LW_PARSE_STATE2_GOT_DIGIT0 state can be repeated unexpectedly without proper parserbuf_index or state checking. This behavior will trigger a heap buffer overflow vulnerability by allowing to write some data. And the writable size is sizeof(unsigned).
* ekf2_derivation: use single source of state definition
The state is defined as an ordered dictionary of group elements and
everything else is generated using that state definition
* ekf2: generated state sample add const reference getter
---------
Co-authored-by: bresch <[brescianimathieu@gmail.com](mailto:brescianimathieu@gmail.com)>
Co-authored-by: Daniel Agar <daniel@agar.ca>
The length check for unknown packets did not include PACKET_SIZE_TYPE_SIZE
and CRC_SIZE, and hence working_index could overflow CRSF_MAX_PACKET_LEN,
triggering invalid memory access further down in QueueBuffer_PeekBuffer.
Also the working_segment_size was wrong for unknown packets.
Credits for finding this go to @Pwn9uin.
This allows to inject an updated ext_autostart folder with the name
ext_autostart_new, and then PX4 takes care of renaming it to
ext_autostart during bootup.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The sparse vector template requires to know which states are non-zero in
the observation jacobian. This complicates the modularity of the code
when the state vector or the derivation is changed.
The computation cost difference is almost negligible for this size.
For FW takeoffs we need to keep the course straight towards the first
waypoint, and not climb in loiter patterns first.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Current threshhold has no margins of errors with the set acceptance radius. Increase corridor radius by 5m.
Increase time to disarm for tailsitter test to pass.
Rverse mission needs check tracks test disabled since mavsdk does not really work with mission has reverse order.
mavsdk-test: added a vtol mission without a landing at the end (used for reversed RTL)
math_helpers: added function to compute local position from a raw mission item
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Dataman: Add write function to dataman cache.
RTL and mission have a new common base class mission_base. Both inherit from them and mission, RTL mission, and rtl reverse mission inherit from them and implement their desired functionalities. This simplifies the logic in mission as well as make the logic in rtl mission reverse and mission more readable.
Rtl mission reverse now functional again for VTOL flying back the mission and transitioning to MC at the home position.
Dataman cache has new write functionality to write to dataman while updating write item in its cache if necessary.
Dataman cache is now only updated when the respective module is active. Leads to a higher computation time once on activation, but decreases unnecessary cache updates when inactive.
This is required to support fixed pitch propeller helicopters that have
no collective but only cyclic pitch with two degrees of freedom and
hence only two servos.
The amount of thrust in the body z axis is then controlled using the
motor speed which makes particularly sense on coaxial helicopters
that need to control yaw with changing motor speeds already.
Events have a global, system-wide sequence number, which must be handled
atomically, (fetching and incrementing the sequence AND sending the event
to uORB must be atomic). Currently in FLAT mode, only one instance of this
sequence number exists, so it is OK to have it in px4_platform.
However, in PROTECTED mode px4_platform is instantiated both in kernel-
and user spaces, which makes two instances of this sequence number, which
causes problems in the mavlink event handling logic.
When mavlink receives and handles events, it expects that:
- The sequence numbers arrive in order (seq n is followed by n+1 etc)
- It increments by 1
- There is only one instance of the sequence number
In PROTECTED mode this is violated, as the kernel and user sequence
numbers run freely on their own. This patch fixes the issue by moving
the event backend to the kernel and by providing user access to it via
ioctl.
Even if there is some horizontal motion, a passing check should be
accepted as the terrain can be flat. However, the vehicle must not be
moving horizontally to invalidate the consistency as a change in terrain
can make the kinematic check temporarily fail.
A setpoint of type IDLE can be published by Navigator without a valid position,
and should be handled in the auto function in FW_POSCTRL_MODE_AUTO. If it wouldn't be
handled there the controller would switch to mode FW_POSCTRL_MODE_OTHER, in which case
no attitude setpoint is published and the lower controllers would be stuck with the
last published value (incl. thrust).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
but this time compared to
2fbb70d9ca
the minimum thrust is ramping to not produce a thrust jump.
The better long term solution will be to always have airmode but
with the effect limited to a magnitude of MPC_MANTHR_MIN.
high rates and (super) expo are necessary for
- acrobatic flying
- fpv
- racing
but they are not useful for:
- a typical vehicle's rate control tuning
- beginners
The defaults that I set in #8036 were put with the assumption Acro mode
is mainly used on racing drones for acrobatic manouvers but instead
users including me use it most of the time to tune any drone.
When tuning the rates are lowered and expo disabled.
My suggested strategy is to make the beginner friendly rates without
expo which are good for tuning the default and document more clearly
how this can be raised for acrobatic flying in documentation and later
on hopefully also directly in the ground station UI
on an Acro mode specific page.
* FW Positon Controller: set altitude_ref to 0 if not provided by GPS
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Positon Controller: set lat/lon reference to 0 if not provided in local_position
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
If no altitude setpoint is specified then takeoff to the default
altitude above the current global position, not above Home.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
c23b72dffe [BACKPORT] sched/semaphore: Remove restriction to use nxsem_trywait from ISR
fd47cd20a2 [BACKPORT] imxrt:Serial Preserve all but W1C bit in SR
c55f0fd3ac [BACKPORT] imxrt: lpspi dma invalidate cache after exchange
198c7caecb [BACKPORT] imxrt:lpi2c fix status handeling & race
cbd2e44c10 [BACKPORT] s32k3xx: lpspi dma invalidate cache after exchange
e71618d60e [BACKPORT] s32k3xx:lpi2c fix status handeling & race
6f59cc3659 [BACKPORT] s32k1xx:lpi2c fix status handeling & race
1e316d7e32 [BACKPORT] imxrt: flexcan use hpwork for receiving frames
67c1c59865 [BACKPORT] net/can can_readahead_timestamp always free iob
8be831a4ff [BACKPORT] imxrt: fix txdeadline add ecc/fd support
00a68b7668 [BACKPORT] fs/cromfs: Fix faulty DEBUGASSERT() check
d5cf545d6e [BACKPORT] S32K3XX EMAC MCAST support Fix compile warning when ioctl is not enabled
4265c830fa [BACKPORT] imxrt:edma {s|d}last needs to be total xfer size
24b4d44896 [BACKPORT] s32k3xx:edma {s|d}last needs to be total xfer size
eed0482f64 [BACKPORT] s32k1xx:edma {s|d}last needs to be total xfer size
36aab4146a [BACKPORT] kinetis:edma {s|d}last needs to be total xfer size
a0faf31f6f [BACKPORT] arch/stm32f7: fixes for pinmap
eb8255121d [BACKPORT] stm32h7:sdmmc It is not an error if no wait was needed
062044fe41 [BACKPORT] board nucleo-h743zi:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
e03f9d3917 [BACKPORT] board olimexino-stm32:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
4c3a467415 [BACKPORT] stm32l5:pinmap Add suffix to all pins and add legacy pinmap
153069ed40 [BACKPORT] stm32wb:pinmap Add suffix to all pins and add legacy pinmap
d84d737f89 [BACKPORT] stm32f0l0g0:stm32f0{3|5|7|9}x_pinmap & stm32g0_pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
5fc7071ac1 [BACKPORT] stm32l4:stm32l4x{3|4|5|6|r}xx_pinmap pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
20061c2aab [BACKPORT] stm32:stm32f10{0|2|3{c|r|v|z}|5{r|v}|7v}_pinmap refactor
4d1f83d484 [BACKPORT] stm32:stm32l15xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
2dfa3f2601 [BACKPORT] stm32:stm32g4xx{c|k|r|m|v|q} pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d206327809 [BACKPORT] stm32:stm32f3{0|3|7}xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
95e66ab508 [BACKPORT] stm32:stm32f20xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d2fd9178ad [BACKPORT] stm32:f4/f412 pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
a9df45166d [BACKPORT] stm32f7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
07dd2b424e [BACKPORT] stm32h7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
1e3065344f [BACKPORT] stm32u5:stm32u585xx_pinmap Fix typo
0a05365a90 [BACKPORT] stm32wl5:pinmap Fix typo
e3834138dc [BACKPORT] tools:Add STM32 Pin migration tool
df851a8768 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h also for stm32h7x7xx
d75dfcf1e9 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h
963f35f4fc [BACKPORT] {stm32,stm32f7,stm32h7,stm32l4,efm32}/otg: rasie an assertion if IN request is not possible to transfer
de2fcc6668 [BACKPORT] {stm32f7,stm32h7,stm32l4}/sdmmc: callback support requires HPWORK
6929144fc2 [BACKPORT] stm32h7/otgdev: FS transceiver must be enabled if OTGFS enabled
a2078afaea [BACKPORT] stm32h7/otg: add support for external ULPI
26e1246c86 [BACKPORT] stm32h7/rcc: OTGHS ULPI works only in VOS0
cd6daa185e [BACKPORT] stm32h7: update ULPI pins
c73c261ae3 [BACKPORT] arch/boards: fix stm32f411-mininum:nsh compilation failure after enabling IRQMONITOR
8078f134ef [BACKPORT] arch/stm32/stm32.h: do not include stm32_usbdev.h if not supported
60e884fa92 [BACKPORT] {stm32,stm32l4,stm32f0l0g0}/otg: move STM32_NENDPOINTS definitions to header files
dda297cb78 [BACKPORT] arch/arm/src/stm32/hardware: Fix register define
362b976b0e [BACKPORT] arch/arm/src/stm32/hardware: Add stm32g4 rcc apb1 timer enable compatibility
434fd71f2c [BACKPORT] {stm32/stm32l4/stm32f7/stm32h7/efm32}/otgdev: remove invalid use of the priv field for EP
2476d24e8c [BACKPORT] {stm32f7,stm32h7}/otg: fix compilation for USBDEV when USB_DEBUG=y
eb43c582ea [BACKPORT] drivers/mtd/ramtron: change nsectors size to uint32
20f61ff0d5 [BACKPORT] fs/littlefs: add full support for LittleFS block device cfg in Kconfig
60471fbf8c [BACKPORT] drivers/mtd: add Kconfig options for RAMTRON emulated page & sector size
- for FW the primary range finder usage is estimating the distance to
the ground (terrain estimate) to guide the landing approach and initiate flare
- increase EKF2_RNG_QLTY_T default 1->3 seconds
- force initialize takeoff airspeed setpoint at start of takeoff modes
- force set airspeed constraints if slewed value is out of bounds
- always slew airspeed setpoints as long as inside constraints
- move target airspeed setpoint calculation into mode specific logic regions (hand vs runway)
when we're in a takeoff situation, we only want to adapt the airspeed to
avoid accelerated stall due to load factor changes. Disable othre logic
like minimum ground speed, wind based adaption and airspeed slew rating.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
From looking at the history the BMM150 rotation was initially 0. Then,
this was changed to 6 when the intent was to only change it for Skynode.
A bit later, the rotation was changed back to 0, but only for Skynode.
This tells me that rotation 0 was correct for all 6X including Skynode
all along.
Signed-off-by: Julian Oes <julian@oes.ch>
- ekf2 heading first initializes to 0 degrees, then immediately resets to mag heading once a few samples are accumulated
- the yaw standard deviation check could be adjusted to exclude this brief (<1s) initial period
- on NuttX if the SD card was just cleared (quick format) it's possible for the newly created uninitialized dataman file to still have the previous compatibility key, which causes the initialization to be skipped
* added a new driver ASP5033 for measuring the differential pressure and airspeed
---------
Co-authored-by: nano <nanobotzhe@abv.bg>
Co-authored-by: Denislav Petrov <you@example.com>
When the yaw estimate is converging, the controller makes the drone yaw
in order to follow the current setpoint. This is unintuitive for the
pilot and it is preferable if the drone continues to fly towards the
same physical direction.
This estimate doesn't converge to the true yaw but can be used as a
more consistent but drifting heading source.
It can be used by a setpoint generator to adjust its heading setpoint
while the true yaw estimate is converging in order to keep a constant
course over ground.
This updates the gps/devices submodule which includes a fix that
requests the Unicore HEADINGA message in case the message is not enabled
by default.
Signed-off-by: Julian Oes <julian@oes.ch>
If the measured voltage is more than 65v we need to split the voltage
over multiple cells in order to avoid overflowing the uint16. This is
according to the MAVLink spec.
Signed-off-by: Julian Oes <julian@oes.ch>
The extension fields need to be 0 by default according to the MAVLink
spec. This is because extensions are 0 by default and need to be 0 when
unknown/unused for backwards compatibility.
The patch also simplifies the flow slightly in that it doesn't create a
temporary array but just fills in the cell voltages directly.
Signed-off-by: Julian Oes <julian@oes.ch>
Fixes the clang error:
/__w/PX4-Autopilot/PX4-Autopilot/src/drivers/drv_hrt.h:297:35: fatal error: identifier '_s' preceded by whitespace in a literal operator declaration is deprecated [-Wdeprecated-literal-operator]
297 | constexpr hrt_abstime operator "" _s(unsigned long long seconds)
- Enable arbitrary euler angle for Mag rotation
- new CUSTOM rotation enum out of the normal enum range
- mag_rot: automatically change to custom if euler rot is set
- sensor_calibration: Magnetometer save custom rotation parameters
- mag_cal: cross mention rotation parameters
- This allows the user to see the RPY options when searching for the rotation parameter
---------
Co-authored-by: Junwoo Hwang <junwoo@auterion.com>
Co-authored-by: bresch <[brescianimathieu@gmail.com](mailto:brescianimathieu@gmail.com)>
Co-authored-by: Daniel Agar <daniel@agar.ca>
During transition to FF, only allow update thrust axis up to 45° as with a high tilt angle
the effectiveness of the thrust axis in z is apporaching 0, and by that is increasing
the motor output to max.
Transition to HF: disable thrust axis tilting, and assume motors are vertical. This is to avoid
a thrust spike when the transition is initiated (as then the tilt is fully forward).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
EffectivenessTiltrotor: link time when to tilt motors to MC position to COM_SPOOLUP_TIME
- remove VT_TILT_SPINUP and special spin up tilt handling form the VTOL module
- now handle the spoolup in the allocation, directly linked to COM_SPOOLUP_TIME
- leave tilts at disarmed value during spoolup
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- when GNSS is used require low mag heading innovations during
horizontal acceleration (yaw observable) to validate the mag
- only fuse mag heading just enough to constrain the yaw estimate
variance to a sane value. Leave enough uncertainty to allow for a
correction when the yaw is observable through GNSS fusion
In the mavlink_receiver code, after a while it will try to resend some
parameter update through the MAVLink instance. But for Iridium links
those are not a good idea. So this adds a condition that prevent the
sending if the MAVLink instance is in Iridium mode.
Related to issue #21496
sem_wait() can be interrupted if the task receives a signal, however
the blockinglist implementation depends on blocking until the semaphore
can be obtained.
Fix a memory overflow in case SENS_BOARD_ROT is set to Rotation::ROTATION_MAX (41) which is not a valid value
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
* Navigator: DO_CHANGE_SPEED: only store sinlge cruising_speed_current_mode
This stored cruising speed setpoint is reset on mode change and
after a VTOL transition.
* Navigator Mission: replay DO_CHANGE_SPEED items when resuming mission
* Navigator: remove cruising_speed_sp_update()
Speed changes in a mission are handled directly in the position controllers,
and no longer in Navigator.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Increased size for ORB_ID from uint8_t to uint16_t
Created a type: orb_id_size_t = uint16_t.
There are still a couple of places where the size
of the ORB_ID is assumed to be less than 16-bits.
The places that I have found are commented regarding
this and can be found with a search on orb_id_size_t.
- split mag_3d into new standalone mag fusion and mag fusion allowed to update all states (full mag_3d)
- new dedicated control logic for mag/mag_3d fusion and standalone mag heading fusion
- if WMM available use for mag_I and mag_B init
- mag states reset if external yaw reset (yaw estimator, GPS yaw, etc)
- mag reset if declination changed (eliminate _mag_yaw_reset_req)
- mag fusion (but not mag_hdg or mag_3d) can be active during gps_yaw or ev_yaw (if yaw aligned north)
Co-authored-by: bresch <brescianimathieu@gmail.com>
- simplify vehicle_status.arming_state down to just armed and disarmed
- ARMING_STATE_INIT doesn't matter
- ARMING_STATE_STANDBY is effectively pre_flight_checks_pass
- ARMING_STATE_STANDBY_ERROR not needed
- ARMING_STATE_SHUTDOWN effectively not used (all the poweroff/shutdown calls loop forever in place)
- ARMING_STATE_IN_AIR_RESTORE doesn't exist anymore
- collapse ArmStateMachine into commander
- all requests already go through Commander::arm() and Commander::dismarm()
- other minor changes
- VEHICLE_CMD_DO_FLIGHTTERMINATION undocumented (unused?) test command (param1 > 1.5f) removed
- switching to NAVIGATION_STATE_TERMINATION triggers parachute command centrally (only if armed)
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
* ekf2-test: remove outdated codegen comparison
The definition of states changed so the comparison with the old
derivation cannot work anymore.
---------
Co-authored-by: bresch <brescianimathieu@gmail.com>
Some system are able to dead-reckon for a while after losing GPS or
other sources providing positional feedback. If the estimated position
error grows above the failsafe threshold, the system enters a failsafe
mode. As the position error estimate is growing linerly over time, and
it is recommended to take action before entering the failsafe, we here
warn the user about the imminent failsafe and propose to take manual
control.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* [not-working] add a gz-omnicopter model
* Fix axis directions on omnicopter model
The omnicopter joint axis directions had to be adapted for sdf 1.9 as it has different conventions for joint axis definitions.
* include model from gz-fuel & remove mesh files
* Fix omnicopter model using fuel
---------
Co-authored-by: Jaeyoung Lim <jalim@ethz.ch>
If at the last powercycle one mission was uploaded, the counter in dataman was 1. On the next powercycle the mavlink mission counter was reset to zero and on first mission upload updated to 1 again. Other modules check, if the mission was changed based on the counter, like the mission.cpp loaded the mission counter from the dataman. On a new mission, the comparison of the counters failed, because both were the same value even if the mission was completely different.
This can be useful if using a full EV + GNSS setup and you start indoors, then fly outside. Once GPS is good and the only missing requirement is yaw alignment the yaw estimator reset is performed and EV yaw will automatically stop itself.
There is no reason to contrsain the position uncertainty, estpecially
when flying with velocitiy aiding only.
Note that all the variances are already contrained to sane values at the
end of the covariance prediction
- set vision attitude error filter uninitialized if vision data stops
- ev error filter is only compiled when ev config is selected
Co-authored-by: bresch <brescianimathieu@gmail.com>
A version update is needed since the dataman is showing errors if data doesn't exist or if it is wrongly stored. This will force default data to be initialized.
There is some actual changes because the earth mag field states are now
reset using the WMM when available. In the replay log, the measured mag
field does not match the WMM and this is why there is a large diff. It
is however more correct now than before.
because sprintf is deprecated on MacOS
and CI fails with warning -> error:
'sprintf' is deprecated: This function is
provided for compatibility reasons only.
Due to security concerns inherent in the
design of sprintf(3), it is highly
recommended that you use snprintf(3) instead.
I updated all versions to the newest one that's used anywhere.
Then at least the straing can be found with full text search.
It's another step towards understanding and unifying the CI environment.
Since we changed the threshold for allowing arming from TRIM/2 to AIRSPEED_MAX
is is very unlikely that one needs to disable this check.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Experience from tuning different VTOL backtransitions showed only having a
I controller is beneficial over a combined FF/I breaking controller.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Case: A vehicle is already operating but has no stick input or another
source than RC. When RC stick input is switched to either because it gets
first time available or as a fallback to joystick then the mode was
immediately changed to the switch position. This can lead to loss of
control e.g. when the vehicle is flying far away and the
mode switch of the RC is in some fully manual piloted mode.
I added tests to cover the cases where RC mode initialization is expected
and also unexpceted because the vehicle is already armed.
modules__ instead of module__ prefix
The module depends on the hysteresis library and probably because
it compiles with the still prevalent global includes the dependency
is not declared.
also for the other linux target builds. It's a follow up to
e5503480e3
I wasn't aware that there are multiple different
container versions used for almost the same build.
in air bias estimation is usually really accurate and should be weighted
more heavily compared to the calibration parameters that are often
more approximate given the worse magnetic environment near the ground.
- since last_us is set to 0 every time the bias is not observable, the
total time was also reset -> needed 30 consecutive seconds in mag 3D
to be declared "stable"
- after landing, the mag_aligned_in_flight flag is reset. Using this for
bias validity makes it invalid before we have a chance to save it to
the calibration.
Opt flow raw innovations can be really large on ground due to the small
distance to the ground (vel = flow / dist). To make the pre-flight check
more meaningful, scale it with the current distance.
Channel values stay over one unit test but some tests assumed they are
reset each time. Reset the channel after these mode button tests.
Parameters survive between unit tests presumably as long as
the bianry runs. Reset them if a test requires that.
This allows PWM and all other output methods to configure
stopped, idling and full thrust points and use them consistently.
The fact that a fixed wing motor can be stopped when zero thrust
is demanded is explicit and could in principle even be disabled.
The mechanism is the same as for a standard VTOL stopping the
multicopter motors in the fixed wing flight phase.
This allows to consistently define:
Motor stopped - disarmed PWM
Motor idling - minimum PWM
Motor at full thrust - maximum PWM
Any allocation can then distinctly decide if
a motor should be running or not depending
on the context and also explicitly command that.
This is required to process data from the ADS1115 ADC and enables the
params BATx_I_CHANNEL and BATx_V_CHANNEL.
Testing is required whether this actually works on Pixhawk 6X though.
Signed-off-by: Julian Oes <julian@oes.ch>
When switching into Hold mode establish a Loiter around current position,
even if we were before already loitering (eg in Mission mode).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Having newline between I think didn't apply the PR stale days setting of
30 properly (it was using 45)
And it seemd that unless I set the days-before-close to -1
intentionally, it would still close the Issue/PRs, as the default value
is 7 already.
Also updated version of the stale action to v8
* Remove old stale bot yaml file
* Remove slack svg file (unused)
* Stale action: Only apply stale label, and no other actions
Respecting the opinion on
https://github.com/PX4/PX4-Autopilot/commit/fa9ac6ecf651232f3105ca124a2d2c54ab8620d0,
it seems reasonable to disable commenting feature, and just keep the
action only applying the `stale` label. This will reduce the noise /
email spams / ping pong fight with the stale bot (Action)
- Remove unnecessary text rendering, which made clicking log links
harder
- Re adjust markdown elements to make it easier to read / intuitive when
creating an issue
Instead of hard-coding the tilting duration (from FW to MC tilt),
expose it as a parameter (VT_BT_TILT_DUR). The default is the same
as the hard-coded value previously (1s).
Slower tilting mechanisms need a higher value here, while for smaller
ones a too high value results in unnecessary delays till the motors
are in hover configuration.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This affects how soon after a backtransition the vehicle has the
full hover controller running again. Specifically it reduces the
duration of the ramp down of the motors prior to tilting them.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
COM_ARMABLE is set to "Disabled" will prevent arming.
This allows to set the parameter when ground demoing a drone or
if it's in maintenance for safety reasons.
const char *data = "www\r\n";
Defines a cstring of 6 bytes: 'w', 'w', 'w', '\r', '\n', '\0'
type of data: char const*
type of &data: char const**
So when we call
write(_fd, &data, strlen(data));
then strlen(data) == 5
and we send the 4 byte memory address of data
+ some additional random byte.
Correct is
write(_fd, data, strlen(data));
where char const* gets casted to const void * and we pass
the pointer to the content of data.
The fundamental problem here is write() not being typesafe.
Before this the ESC calibration aborts if battery detection doesn't work.
The problem is if the user still connects the battery as he gets instructed
and the calibration aborts then the ESCs are in calibration mode and
after abortion calibrate to the wrong value.
Also I realized there's no additional safety by aborting the calibration
if the battery cannot be detected during the timeout because a pixhawk
board without power module will report a battery status from the
ADC driverand in it that no battery is connected which is the best
it can do. In this situation the motors will still spin if the
ESCs are powered.
Some ESCs e.g. Gaui enter the menu relatively quickly if the
signal is high for too long. To solve that it's kept high shorter.
Also all tested ESCs detect the low signal within a shorter time
so no need to wait longer.
- Change timings for a more reliable calibration.
- Make sure there's an error message when battery measurement is not
available also when it gets disabled after system boot in the power
just above the calibration button.
- Safety check if measured electrical current goes up after issuing the
high calibration value for the case the user did not unplug power
and the detection either fails or is not enforced.
Before:
When the mixed throttle for the motor was exactly zero the ramp went
from the disarmed PWM value to the minimum PWM value.
When the throttle was even just slightly different from zero the ramp
made a jump up to the commanded throttle scaled between
disarmed PWM and maximum PWM, then ramped between
disarmed PWM and minimum PWM and at the end jumped up again to
the commanded throttle scaled between minimum PWM and maximum PWM.
After:
The ramp goes from disarmed PWM value to the the
commanded throttle scaled between minimum PWM and maximum PWM.
If the commanded throttle changes during the ramp then the scale and
hence also end value of the ramp changes.
When at rest, directly fuse the gyro data as an observation of its bias.
This allows to strongly observe the gyro biases without having to fuse a
constant heading that makes the ekf too confident about its heading.
The entire logic did not work for the case when the throttle channel is
reversed because then QGC sets trim = max for that channel and
the result is only half the throttle range.
This adds support for the TI LP5562 RGB LED driver.
Things to note:
- The driver is initialized in simple PWM mode using its internal clock,
for R,G,B, but not for W(hite).
- The chip doesn't have a WHO_AM_I or DEVICE_ID register to check.
Instead we read the W_CURRENT register that we're generally not using
and therefore doesn't get changed.
- The current is left at the default 17.5 mA but could be changed using
the command line argument.
Datasheet:
https://www.ti.com/lit/ds/symlink/lp5562.pdf
Signed-off-by: Julian Oes <julian@oes.ch>
* Removed obsolete voxl2-io directory
* Updated support for ModalAI FC v2 board
* Added UAVCAN back in and removed local position estimator and attitude estimator Q that are no longer supported.
* Removed unneeded IMU drivers
set_vtol_transition_item sets the params of the mission item directly
to values that make sense for NAV_CMD_DO_VTOL_TRANSITION, but don't
for other NAV_CMDs. So make sure that whenever we use it, we then in
the next step reset the touched mission_item fields.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Our serial_test showed only ~84kB/s with the default 256 RX buffer size
with significant ~2.5ms periods of the flow control RTS pin being
asserted. Increasing size to 600 (same as FMU-v5x) brings the throughput
only to ~190kB/s, while a size of >1500 achieves ~350kB/s. Larger RX
buffers do not increase throughput anymore, while the theoretical
maximum is 375kB/s.
Transmit buffer size is increased to 10kB same as on FMUv5x to prevent
any future differences in queue behavior and throughput. serial_test
showed ~350kB/s throughput at 3kB TX buffer size, so this is just a
precaution.
* refactored uncommanded descend quadchute
- use fixed altitude error threshold
- compute error relative to higest altitude the vehicle has achieved
since it has flown below the altitude reference (setpoint)
* disabled altitude loss quadchute by default
* altitude loss quadchute: added protection against invalid local z
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- ArmingStatus DroneCAN message STATUS field is only set to true based on
arming_status.armed
- Cannode prearm state is set to true always when ArmingStatus DroneCan
message is received
- Instead we disable interrups on Nuttx where needed
- No lock is held during param export. Params can be changed
concurrently and we rely on the fact that another export will be
triggered in that case.
5s is a more reasobale time for tailsitters, which rely differently on this param
than other VTOL types. Tailsitters will ramp the pitch up withing this time,
while for other VTOLS types its only the max transitiont time.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This is now using the advanced lift drag plugin.
The important step was to enable airmode for yaw, otherwise yaw gets
saturated at low throttle and we can barely roll.
The other trick was to raise airspeed a little bit to avoid operating
too much at the lower end of throttle where control authority is low.
Signed-off-by: Julian Oes <julian@oes.ch>
* RateControl: rename setGains to setPidGains to be more precise
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Rate controller: only allow to disable Yaw in Acro, not roll and pitch
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- re-enable once the estimator selector respects configured mag
priority (at least initially) or is otherwise able to automatically
prefer an external mag over internal
- for SITL disabled because the full matrix of esitmator instances
(IMUs X mags) was too many topics for logger currently
Transitions in Stabilized mode are done manually, the pilot controls the pitch angle
and if it's above the threshold the transition is declared finished (plus airspeed
check for front transition). Thus we can't have fixed thresholds but need to link
them to the actual max pitch angle in Stabilized mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
We currently fuse 0 as airspeed rate measurement, and thus simply low-pass
filter the airspeed measurements. Testing has shown that the current default
on the airspeed rate measurement noise is set to low, and thus the airspeed
mesurement is filtered too much.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A VTOL plane in MC mode has no yaw setpoint during takeoff because of
weather-vane. To align for the front transition, the yaw target jumps
and caused a step in the controller, making it reach saturation.
With this commit, the previous yaw setpoint is set to the current yaw
when no yaw setpoint is sent in order to create a smooth yaw trajectory
starting at the current orientation when yaw target is suddenly finite.
The yawspeed filter also now contains the yaw speed instead of dyaw in
order to prevent chattering due to dt jitter.
The API is cleaner if the control_data is const reference and the device
compid is an explicit output argument.
Signed-off-by: Julian Oes <julian@oes.ch>
The resets in the modes (eg Loiter mode) are not active yet, so manually
set rep->current.cruising_speed = -1.f if not already in the same flight mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When flow control is used together with DMA, we need to add a pulldown
to CTS. Without it, it assumes flow control and gets stuck when
CTS is not connected.
Signed-off-by: Julian Oes <julian@oes.ch>
When we fall back to another link, we are already doing a uORB copy when
checking the data. Therefore, we should further down use/send that data
instead of overwriting it immediately.
Signed-off-by: Julian Oes <julian@oes.ch>
I don't think it makes sense to slow down switching RTCM injection to
once every 5 seconds. If we don't have corrections, we should check and
use whatever we get as soon as possible.
Signed-off-by: Julian Oes <julian@oes.ch>
We need to reset the instance after looping through all instances.
Otherwise, we are left with the last instance if none is valid but have
not updated the _selected_rtcm_instance which is what is logged.
Therefore, this change fixes the logged RTCM instance.
Signed-off-by: Julian Oes <julian@oes.ch>
It turns out that I had omitted implementing the gimbal_device_id which
is the component ID of the gimbal device that the gimbal manager (in
this case PX4) is responsible for.
Signed-off-by: Julian Oes <julian@oes.ch>
Once passed the transition and in FW mode, it takes some ms unitl the FW att sp is updated
by the FW att controller. During this time the last published attitude sp is kept bein used,
which is the one that was published during transition. So let's fill the thrust[0] of it.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This adds the ability to manually set who has primary control over a
gimbal and also adds printing it as part of the status.
This is helpful, especially while working on the QGC gimbal v2
implementation.
Signed-off-by: Julian Oes <julian@oes.ch>
A default of 10s makes more sense compared to the old 4s, as this is only the
max time of a back transition and it's also decleared completed if the
speed drops below the hover cruising speed (MPC_XY_CRUISE).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
There have been substantial TECS changes lately, and the config files
for custom VTOLs have not been updated since a long time. I would thus
rather use the default TECS gains for lightly maintained configs.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
with the goal to make it more clear and the error only appear when
armed but every time the running task doesn't actually match
the mapping inside the start_flight_task() function.
* Navigator: on_mission_landing() only can return true if currently in mission mode
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* RTL: reset RTL state when not in RTL nav_state
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Navigator: fix mission vs. normal RTL
- remove extra state _should_engange_mission_for_landing from rtl and have
this logic outside of RTL where Navigator decides on running mission RTL or normal RTL
- fix logic in Navigator to decide mission RTL vs normal RTL
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Mission: land_start(): fix decision if already on mission landing
Simply checking landing() is not enough, as that is not reset until
set_current_mission_index(get_land_start_index()) later in the function.
Instead ask Naviator about it (on_mission_landing()).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Navigator: only update _shouldEngangeMissionForLanding once, to not set it to false after VTOL backtansition
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Port of the PX4 Vision gazebo-classic model to Gazebo. With Gazebo Garden, everything seems functionnal.
* Port of the PX4 Vision gazebo-classic model to Gazebo.
With Gazebo Garden, everything seems functionnal.
* Added airframe for command make px4_sitl gz_px4vision
* revert author field
* Import model from Ignition Fuel instead of defining it directly in the .sdf
Tests showed that sideslip fusion often starts just before airspeed
fusion, resetting the wind states to 0 instead of using the airspeed
data. A quick look at the wind uncertainty allows to know if the current
wind estimate is meaningful or if we should rather reset it using the
airspeed data.
- if the height rate input into TECS is finite, use that one to
update a velocity reference generator
- if the velocity reference generator reports position locked or
height rate input is not finite, then run altidue reference generator
- run altitude controller only if altitue is controlled
if height_rate_setpoint is set, only use that one to update altitdue trajectory
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FWPositionController: add linear airspeed-to-trim-throttle mapping
Scale trim throttle in a linear way with airspeed.
Different gradients above/below trim airspeed.
The airspeed- and airs density-corrected trim throttle is required for an accurate
throttle prediction in TECS, while the default trim throttle is still needed
as well, as the throttle delta from height rate setpoint delta is linked to it.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Navigator: change way of telling logic if RLT was started just now
* Navigator: change logic around when to engage Mission mode for RTL
To find out if we're currently on a mission landing, check if we either are
past the land start marker OR currently land start marker is current WP
and vehicle is already in LOITER mode.
* Navigator: do not engage RTL at all if already on mission landing
* Navigator: consider to be on mission landing if the LOITER_TO_ALT and dist small
To find out if we're currently on a mission landing, check if we either are
past the land start marker OR currently land start marker is current WP,
the type is LOITER_TO_ALT and the vehicle is inside loiter.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This fixes the case where the hardware detection fails on CubeBlack when
a CAN device is connected to CAN1 and talking, and therefore preventing
the check from getting a clear result.
Signed-off-by: Julian Oes <julian@oes.ch>
This consolidates the version/revision detection function.
This should allow for actual changes in a follow up commit.
Signed-off-by: Julian Oes <julian@oes.ch>
- multi-instances support is removed from the parameter definitions.
- XRCE_DDS_AG_IP allows to define the agent IP when udp transport is used.
The parameter is used by default if the module is started without the -h argument.
- XRCE_DDS_PRT allows to define the agent listning udp port when the
udp transport is uded. The parameter is used by default if the module is started
without the -p argument.
- Tools/convert_ip.py assists in converting ips in decimal dot notation into int32
notation.
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
To prevent mission rejections when vehicle is currently far away from Mission start,
but planned home is close to it.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* MAVSDK_Test_Runner: Place PX4 instance runner after Gazebo server runner
- This was a nasty bug where starting PX4 instance first, then starting
Gazebo server was causing PX4 instance' EKF to freak out, probably
because it doesn't like getting data a while after it is started
- Detailed breakdown is given here: https://github.com/PX4/PX4-Autopilot/issues/21229#issuecomment-1450761542
- This now guarantees that such edge case won't occur and MAVSDK test
will run as it should
* MAVSDK Test Runner: Retain comment within 79 character limit
- To pass flake8 python style check
* Update test/mavsdk_tests/mavsdk_test_runner.py
Co-authored-by: Julian Oes <julian@oes.ch>
---------
Co-authored-by: Julian Oes <julian@oes.ch>
Testing has shown that 10m is a bit too tight, most of all as this check is also run in not height-controlled
flight modes (eg Stabilized), and there 10m altitude loss during transitions can happen easily.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This adds the Cube Orange+ to the list, and also changes the Hex naming
to CubePilot as that is how it is sold/marketed now.
Signed-off-by: Julian Oes <julian@oes.ch>
The attitude frame is wrong for tailsitters doing side slip fusion for wind estimation.
It doesn't take into account that the frames is 90deg tilted in FW flight.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
-set roll/pitch used for failure detection during transition to 0
-rotate estimated attitude 90° in FW flight
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
to enable proper automatic output in gtest unit tests
that compare two `Matrix`, `Vector` or two `Dual` objects.
Credits to @jwidauer for showing me this trick.
Maximum plaintext length was wrong, it is just k - 2 * hLen -2, where k is RSA key modulus length and hLen is hash length
Also minimum block that can be encrypted didn't make sense for RSA-OAEP, it is just 1 byte, the rest will be padded.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Bootloader needs to have a mechanism to de-initialize crypto, in case some HW accelerator
is being used. This adds the needed function for it
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Camera controls should not happen through the flight controller, and
the control allocation has no means of controlling the camera zoom.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- add unit tests for adsb conflict detection
- move adsb conflict detection to lib/adsb and adsb conflict class
- use containers/Array.hpp for buffer array
- expand fake_traffic
This adds a parser for Unicore sentences sent in-between NMEA sentences.
This brings support for the Unicore UM982 module which publishes heading
information based on the two antennas.
Signed-off-by: Julian Oes <julian@oes.ch>
If NuttX is built without support for SMPS it can brick the hardware.
Therefore, I suggest that we add this additional compile-time check.
Signed-off-by: Julian Oes <julian@oes.ch>
It turns out that when you rotate by 45 degrees, as required on the
CubeOrange+, then you can easily get into clipping because the vector
components are constrained after the rotation. In order to avoid that,
we have to avoid getting close to the int16 range and switch from 20 bit
resolution to 16bit resolution earlier.
Signed-off-by: Julian Oes <julian@oes.ch>
This switches from attitude_estimator_q to EKF2 which should now work
without mag when the params are set to SYS_HAS_MAG = 0 and
EKF2_IMU_CTRL = 7 to enable gravity fusion.
Signed-off-by: Julian Oes <julian@oes.ch>
PX4_SIM model need the simulator (gz_) prefix
Fix post debug task
Add x500_depth, rc_cessna, standard_vtol
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
- Add the possibility in the parser to replace the defines made in the current file with their argument (includes are not supported)
- Add the possibility for the parser to parse int argument with bitwise shift operators
- remove deprecated actuator_controls[INDEX_FLAPS/SPOILERS/AIRBRAKES]
- use new topic normalized_unsigned_setpoint.msg (with instances flaps_setpoint
and spoilers_setpoint) to pass into control allocation
- remove flaps/spoiler related fields from attitude_setpoint topic
- CA: add possibility to map flaps/spoilers to any control surface
- move flaps/spoiler pitch trimming to CA (previously called DTRIM_FLAPS/SPOILER)
- move manual flaps/spoiler handling from rate to attitude controller
FW Position controller: change how negative switch readings are intepreted
for flaps/spoilers (considered negative as 0).
VTOL: Rework spoiler publishing in hover
- pushlish spoiler_setpoint.msg in the VTOL module if in hover
- also set spoilers to land configuration if in Descend mode
Allocation: add slew rate limit of 0.5 to flaps/spoilers configuration change
Instead of doing the flaps/spoilers slew rate limiting in the FW Position Controller
(which then only is applied in Auto flight), do it consistently over all flight
modes, so also for manual modes.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- remove deprecated actuator_controls[INDEX_LANDING_GEAR]
- remove dead code in mc rate controller that used to prevent it from being retracted
on the ground (anyway had no effect as it only affected the actuator_control[LANDING_GEAR]
which wasn't sent to the control allocation)
- for VTOLs handle deployment/retraction of landing gear in AUTO as a MC (retract if
more than 2m above ground, deploy if WP is a landing WP), plus additionally when transition
flight task is called (ALTITUDE mode and higher)
- for FW in AUTO: add logic in FW Position Controller, depending on waypoint type mainly
- manual landing gear settings always come through (a manual command overrides a previous
auto command, and vice-versa)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Tiltrotor_extra_controls also contains collective thrust beside collective tilt, as passing a 3D
thrust setpoint vector beside the tilt is not feasible.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Changed the method of checking and setting the server file lock on Posix to avoid conditions where the server can indicate that it is running but still hasn't finished it's initialization
- always publish esc_status
- when enabled via MODAL_IO_VLOG param, enable actuator debug output
- for modal_io commands, use ESC HW ID values instead of motor number for easier use
- publish esc_status message for command line commands
- Uncommented the code that fills in the cmdcount and power fields in the esc_status topic
---------
Co-authored-by: Travis Bottalico <travis@modalai.com>
- if timestamp (or timestamp_sample) unpopulated fill it with current hrt_absolute_time()
- if using provided timestamp don't allow it to exceed current hrt_absolute_time()
- Switching to the first order filter that was previously
only in FlightTaskManualAltitude.
- Moving the scaling of full stick deflection to
radians per second into the class.
* RTL: only do calculations in is-inactive if global position is recent
* RTL: refactor calcRtlTimeEstimate to only calc and not pub
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When requesting a message from a stream that is not active we start the
stream with interval=0 and call the request method once. For all streams
this works fine except the gps_global_origin. For this one the request method
is actually overidden to throttle down the rate and not just send out the message.
This will cause this message to never being sent on request if the stream
is not active by default.
* Update README: Maintainers, Boards, Roadmap
- First step after the community coordination call from January 30th
* README: Fromat list & remove discontinued boards & add others
- Addressed comments
* README: Add Simulation, remove QGC
- Only leave the PX4 specific categories (QGC is not)
* Add Beniamino as ROS2 maintainer
* README: Add note that README is main source of truth for maintainers
- We need to have a source of truth, we can use Github README for that.
- vectornav library (libvnc) fixed for NuttX
- open serial port O_NONBLOCK (like __APPLE__)
- set serial port baud rate with cfsetspeed (like __APPLE__)
- vectornav backend thread increase stack and run at higher priority (SCHED_FIFO)
Block Device driver uses a buffer so we need to ensure data is written or read to the device and not to the buffer so we can be sure if the device works properly
* Cyphal: fix comparing floating-point issue
* Cyphal: fix setpoint serialization
* Cyphal: fix bug with wrong comparasion of param name and pub/sub name: remove prefix from UavcanPublisher::updateParam and UavcanDynamicPortSubscriber::updateParam and PublicationManager::updateDynamicPublications
* Cyphal: integrate UavcanEscController with PublicationManager, remove second instance of UavcanEscController from CyphalNode
* Cyphal: publish readiness with minimal frequency because according to UDRAL The drive shall enter STANDBY state automatically if the readiness subject is not updated for CONTROL_TIMEOUT
* Cyphal: increase setpoint publish rate from ~75 to 200 by removing PX4_INFO (it really significantly react on the the output rate) and changing the mixing output rate and the shedule interval
* Cyphal: restore prefix because we need it for uorb over uavcan/cyphal and add udral prefix for non uorb pub/sub
* Cyphal: fix DynamicPortSubscriber subscription: if it has multiple subscribers, it should call subscription only after updating of all port subscribers port identifiers
* Cyphal: fix SubscriptionManager: we should take care about prefix
* Cyphal: fix readiness for test motor mode
* [Cyphal] Fix dynamicsubscription, improve printinfo, enable MR-CANHUBK3 config
---------
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
- pass new airspeed sample around when available
- can't completely eliminate _airspeed_sample_delayed until resetWind()
called from sideslip fusion is updated
- reduce boost priority to PX4_WQ_HP_BASE - 6
- add cli command 'trigger_watchdog' to manually trigger watchdog
- add perf counters when triggering watchdog
- reduce top measurement to 300ms
- restore priorities after 1.5s
There are precautions in case the SD card code itself has a busy-loop.
Enable automatic landing abort on timed out distance sensor reading also for
the circular landing. Do not enable the no-terrain timeout check, as, opposed
to the straight landing, we here don't know when to expect the distance sensor
to get valid.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
As we don't know the landing point altitude in non-mission landings, assume
the worst case (abort right before touchdown) and thus always climb
MIS_LND_ABRT_ALT on triggering an abort.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Add method for circular landing, that is used instead of the straight fixed-wing
landings in case the landing is not part of a mission landing.
Use straight landing if previous WP is valid, and the ciruclar otherwise.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
_land_start_index is used to to start the mission from this item index, and to
avoid to publish a triplet.current.type=IDLE, we need to fill it with the actual
position setpoint that the vehicle should go to at the start of a mission landing.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Prior commit added opening of /dev/null as 0, 1 and/or 2 file
descriptors, if they where not present. However, if the temporary
file descriptor used to open /dev/null matched the target file
descriptor, it would be immediately closed again. This commit fixes that,
and does not duplicate and close the temporary file descriptor if it is
already at the correct number.
- new FIFO_RESET state used to give the sensor more time after successful configuration before sampling begins
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
* rtl: remove unconditional transition to land after descent
This was a bug, as it renders the above code lines useless.
This would cause a undesired FW landing for VTOL vehicles if
RTL_LAND_DELAY is above 0.
* rtl: head to center after loiter in VTOL FW
To get the same behavior for RTL with and without loiter before land for
VTOL drones.
* rtl: always go to descend state after return
Previously, the state would change directly to land if in MR and
RTL_LAND_DELAY was 0.0, but we will still wish to descent to
RTL_DESCEND_ALT at descent speed, instead of using landing speeds.
* rtl: mark head to center state as part of vtol transition
The next step in the sequence is transition to MC. By setting
vtol_back_transition we ensure that the acceptance radius is adapted to
the expected transition distance.
If 0, 1 and/or 2 file descriptors are not open when mavlink module
starts (as might be the case for USB auto-start), use default /dev/null
so that these numbers are not used by other other files.
Instead of interpret a request for "more logs than currently exists" as
a new request, use a request for index 0, which is more likely to be
the first request.
* [npfg]: Remove the guideToPoint function and replace with guideToPath
* [npfg]: remove unused navigateXXX functions
* [npfg]: Move navigateXXX Function into FWPoscontrol
* [FixedwingPositionControl]: Set default flaps and spoilers in attitude setpoint topic, and only change if necessary.
- precision landing works incorrectly, target position is not updated during the descent above target
- _prepareLandSetpoints needs to update _land_position continuously
Co-authored-by: kapacheuski <kapacheuski@gmail.com>
- the thermal offsets are an optional correction applied to the raw data, so when updating an existing calibration offset with new learned bias we don't want this incorporated
- EKF isTimedOut(), isRecent(), and isNewestSampleRecent() need to handle the case where the timestamp has never been set
- reset() more thoroughly reset fields (mainly impacts unit tests)
Set this flag to true if local position is valid but accuracy low, such that
the operator can be warned before system switches to position-failure failsafe.
Additionally, switch to RTL if currently in Mission or Loiter to try to reach home
or fly out of GNSS-denied area.
Set low accuracy threshold to 50m by default for FW and VTOL.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Otherwise the flight time restriction flag gets cleared too early, before
disarming (which puts the vehicle into the previous mode and it might
take off again).
Fixes the following case:
- user intention set to X
- failsafe triggers, mode = Y
- can_run for X becomes false
- user tries to switch to X
-> need to re-evaluate can_run
Previously, it was not possible to enable forwarding of messages to/from
teh USB instance because it does not have a param for it, like the
serial instances have.
With this commit, we change the default to always set forwarding on for
the USB instance as that is likely desired.
Signed-off-by: Julian Oes <julian@oes.ch>
- from the C standard, "All identifiers that begin with an underscore and either an uppercase letter or another underscore are always reserved for any use"
- from the C standard, "All identifiers that begin with an underscore and either an uppercase letter or another underscore are always reserved for any use"
The static object is destroyed on at_exit while threads might still be
inside a CS. This can lead to a hanging process.
Cleaner would be to gracefully stop the threads.
According to https://linux.die.net/man/3/pthread_cond_destroy:
Attempting to destroy a condition variable upon which other threads are
currently blocked results in undefined behavior.
Instead check if system has previously switched into LOITER to acheive the current
WP of type POSITION, and in that case stay in LOITER until altitude is reached.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Do the same as DO_REPOSITION wit only the altitude field populated
and MAV_DO_REPOSITION_FLAGS set, which means:
- switch to Loiter mode if not already in it
- set the current altitude to what is specified in the altitdue field,
keep current altitude setpoint otherwise
- keep current position setpoint
- fall back to current estimated position in case a position setpoint
is not finite
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Previously the condition was based on hard coded height rate estimate and
setpoint values and an altitude error threshold. That showed to be leading
to false positives when the vehicle doesn't tightly follow the altitdue
ramp given by TECS to achieve a new altitude setpoint, and has become
completely infeasibly with the latest TECS rework that leads to non-ramped
altitude setpoint changes in the tecs_status message.
The new check no longer checks the altitude error but only the height rate
instead. It begins to integrate the height rate error once it detects an
uncommanded descend condition (height rate negative while setpoint is
positive). Integral threshold can be tuned by user (VT_QC_HR_ERROR_I).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
In rare occasions asking for the protocol values after setting it returned
[0, 0]. I did not see any documentation for having to wait, but adding a
short wait period fixes it.
- refactor all EKF backend output predictor pieces into new OutputPredictor class
- output states are now calculated immediately with new high rate IMU rather than after EKF update
- IMU delayed sample is passed as around as control data to avoid storing an extra copy and make the requirement clear
- update motor mapping to use new UART_ESC_FUNC* auto generated params
- add support for actuator_test msg to support Actuator Testing in QGC
- modalai_fc-vX targets start driver if configured
- keep track of ESC spin direction in own param
- set ramp up param in MixerOutput to false
- use `gazebo-classic` everywhere consistently referring to the original Gazebo (eg version 9,10,11)
- additional `gazebo_*` helper targets added for compatibility, but warn about deprecation and tell you the new target naming
- use `gz` everywhere when referring to Gazebo (aka Ignition Gazebo or new Gazebo)
For the esc_calibration code, the actuator test is published for each motor
in a row. If the orb queue size is too small, messages are lost and not
received in mixer_module.
Set the default orb queue size of ActuatorTest high enough to keep the commands
for all motors in the queue.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Strictly follow the following convention for tailsitter:
FW Attitude and FW rate controller always operate in the FW frame, meaning that roll is
roll in FW, which for tailsitter means around the yaw axis in the body frame. The interfaces
between modules is though always in body frame.
That enables us to do the axis transformations for tailsitter, that are currently distributed
all over the controller (attitude, rate, vtol module), only at the input and output data of modules.
Side effect is that the FW rate control tuning gains meanings change: while before the roll gains
where meant for the body axis, they are now always applied for the FW roll axis (also in hover). So
the naming now is correct for FW, while before it was for Hover.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This failsafe flag is currently used for not allowing to re-transition to FW, as well
as disabling pusher assist in hover. Till now it was only possible to reset it with
a commanded transition to MC, which many ground station interfaces didn't allow
as the system, after a quad-chute, already was in MC mode.
Hereby it is changed to reset when a new transition to FW is triggered (either via
RC switch or MAVLink command). It is the users responsibility to assess the situation
after a quad-chute happened to try to transition to FW again, manually proceed/land
the vehicle in MC, or let it finish the defined behavior after a quad-chute.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
When we receive a command_long or command_int message to
answer, it arrives with a source sysid/compid, so this means we can send
the command_ack back on the appropriate MAVLink instances instead of all
of them.
This commit filters outgoing command_ack messages, so they are only sent
on the MAVLink instances where the sysid/compid has been seen in the
past.
This means that a command_ack is likely still sent on multiple links for
a setup with redundant links.
This should also prevent command_acks from being blasted on Iridium links
when it's not required.
Signed-off-by: Julian Oes <julian@oes.ch>
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
## Please note that feature requests are not 'fire and forget'
It is a lot more likely that the feature you would like to have will be implemented if you keep watching your feature request, and provide more details to developers looking into implementing your feature, and help them with testing.
- type:textarea
attributes:
label:Describe problem solved by the proposed feature
description:A clear and concise description of the problem, if any, this feature will solve. E.g. I'm always frustrated when ...
validations:
required:true
- type:textarea
attributes:
label:Describe your preferred solution
description:A clear and concise description of what you want to happen.
validations:
required:true
- type:textarea
attributes:
label:Describe possible alternatives
description:A clear and concise description of any alternative solutions or features you've considered.
validations:
required:true
- type:textarea
attributes:
label:Additional context
description:Add any other context or screenshots for the feature request here.
Note: This is the source of truth for the active maintainers of PX4 ecosystem.
See also [maintainers list](https://px4.io/community/maintainers/) (px4.io) and the [contributors list](https://github.com/PX4/PX4-Autopilot/graphs/contributors) (Github).
See also [maintainers list](https://px4.io/community/maintainers/) (px4.io) and the [contributors list](https://github.com/PX4/PX4-Autopilot/graphs/contributors) (Github). However it may be not up to date.
## Supported Hardware
This repository contains code supporting Pixhawk standard boards (best supported, best tested, recommended choice) and proprietary boards.
Pixhawk standard boards and proprietary boards are shown below (discontinued boards aren't listed).
For the most up to date information, please visit [PX4 user Guide > Autopilot Hardware](https://docs.px4.io/main/en/flight_controller/).
### Pixhawk Standard Boards
* FMUv6X and FMUv6U (STM32H7, 2021)
* Various vendors will provide FMUv6X and FMUv6U based designs Q3/2021
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Peter van der Perk
