Fixes the compile error on llvm:
mixture of designated and non-designated initializers in the same initializer list is a C99 extension [-Wc99-designator]
- a growing number of samples come into the backend with the time
already delayed (sensor's interrupt setting timestamp sample)
- if the incoming timestamp is already delayed then the new data checks
(relative to latest IMU) can be slightly wrong
- handle almost all timestamps and checks on delayed time horizon,
except for explicit checks of new samples
- isRecent() and isTimedOut() helpers use delayed time
- add new isNewestSampleRecent() used for checking the incoming
timestamp of the incoming (adjusted) data
- print list of events whenever they change if
CONSOLE_PRINT_ARMING_CHECK_EVENT is set, instead of on each update call
- reduce flash usage by moving out templated code into non-template method
For SITL it's important that the GCS receives the first events messages
that reset the sequence number, in case the user does not press 'Disconnect'
when restarting SITL.
- new modules/simulation directory to collect all simulators and related modules
- new Tools/simulation directory to collect and organize scattered simulation submodules, scripts, etc
- simulation module renamed to simulator_mavlink
- sih renamed to simulator_sih (not a great name, but I wanted to be clear it was a simulator)
- ignition_simulator renamed to simulator_ignition_bridge
- large sitl_target.cmake split by simulation option and in some cases pushed to appropriate modules
- sitl targets broken down to what's actually available (eg jmavsim only has 1 model and 1 world)
- new Gazebo consistently referred to as Ignition for now (probably the least confusing thing until we fully drop Gazebo classic support someday)
Also remove the legacy "range aid" than can be achieved by setting the
height reference to range finder and the range finder control parameter
to "conditional".
Conditional range aiding cal also be set when the height reference isn't
the range finder. This prevents the ratchetting effect due to switching
between references.
Instead of having a single height source fused into the EKF and the
other ones "waiting" for a failure or the primary sensor, fuse all
sources in EKF2 at the same time. To prevent the sources from fighting against each
other, the "primary" source is set as reference and the other ones are
running a bias estimator in order to make all the secondary height
sources converge to the primary one.
If the reference isn't available, another one is automatically selected
from a priority list. This secondary reference keeps its current bias
estimate but stops updating it in order to be the new reference as close
as possible to the primary one.
- much simpler direct interface using Ignition Transport
- in tree models and worlds
- control allocation output configuration, no more magic actuator mapping to mavlink and back
- currently requires no custom Gazebo plugins (keeping things as lightweight and simple as possible)
Co-authored-by: Jaeyoung-Lim <jalim@ethz.ch>
-always reset roll/pitch/yaw integrators at the same time
-reset them while waiting for launch or during FW Takeoff before Climbout
-reset wheel rate integrator only when disarmed
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Since the horizontal and vertical velocity controllers are now
decoupled, it can be that the horizontal acceleration produced by the
controller is actually greater than the desired one (by design). This
condition would actually make the ARW run "backwards", degrading the
controller performance.
Directly use yaw controls for it, and don't add it to the allocation matrix,
as that would have an effect on rudder scaling if the wheel also would have
a yaw effectiveness.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This is the control surface type for airframes that have only a
single aileron servo or have the ailerons on a single output channel.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
2fbb70d9ca made the lowest possible
throttle value commanded by stick in Stabilized mode before taking off 0.
The real world problem with this is that when takeoff is detected then
the entire throttle scaling range jumps from
[0, MPC_MANTHR_MIN]
to [MPC_MANTHR_MIN, MPC_MANTHR_MIN].
As a result whenever MPC_MANTHR_MIN is not zero there is a thrust jump
on every takeoff just at the moment takeoff is detected even when the
stick is moved continuously.
Because of this I suggest to revert to having a higher throttle value
from the beginning on because it's less complicated and there's
no obvious value in starting out with zero thrust if anyways not
possible to go back to zero for safety once takeoff is detected.
Using the control status flags isn't robust as this part of the code
runs at the EKF update rate while the in_air transition is don at the
prediction rate. It was then likely to miss the transition
Fixes the error
googletest-src/googletest/src/gtest-death-test.cc:1283:24: error: ‘dummy’ may be used uninitialized [-Werror=maybe-uninitialized]
with GCC 11
For most VTOLs the param defaults for the agressiveness of the MC attitude controller
are too high, as VTOLs usually have high intertia and lot af drag due to wings and
can thus not rotate as fast as MCs.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
I think most vehicle can safely decend with at least 1.5m/s, and having this
value too low makes Descents/Landings/RTLs unnecessary long.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The VTOL default was set to 1, while the param default is 1.5.
I don't see why it shuold be a different default for VTOLs and thus remove it.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- replace float32[21] URT covariances with smaller dedicated position/velocity/orientation variances (the crossterms are unused, awkward, and relatively costly)
- these are easier to casually inspect and more representative of what's actually being used currently and reduces the size of vehicle_odometry_s quite a bit
- ekf2: add new helper to get roll/pitch/yaw covariances
- mavlink: receiver ODOMETRY handle more frame types for both pose (MAV_FRAME_LOCAL_NED, MAV_FRAME_LOCAL_ENU, MAV_FRAME_LOCAL_FRD, MAV_FRAME_LOCAL_FLU) and velocity (MAV_FRAME_LOCAL_NED, MAV_FRAME_LOCAL_ENU, MAV_FRAME_LOCAL_FRD, MAV_FRAME_LOCAL_FLU, MAV_FRAME_BODY_FRD)
- mavlink: delete unused ATT_POS_MOCAP stream (this is just a passthrough)
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
fix test by reducing the distance to the new origin: the maximum size of
the local position origin is a cube of 1e6m. If the origin is moved
further than this, the state is clipped to that maximum value
Navigator sets the cruise_speed to -1 if the controller shouldn't listen to
it and instead use the default speed (for MC: MPC_XY_CRUISE). This is for
example for RTL the case, where we want to return at the default speed,
independetly of what the mission speed before was.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Add support for the basic GPS telemetry values when using the GHST protocol.
* Fix formatting in GHST GPS telemetry changes
* GHST GPS Telemetry formatting cleanup
* GHST GPS Telemetry, Last formatting change
- synthetic airspeed will only be declared valid as soon as the wind variance
has dropped below a parameterized threshold. This is useful for vehicles without
an airspeed sensor which rely on synthetic airspeed but only once the vehicle
has turned sufficiently for the wind estimates to be reliable.
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- msg constant names now comply with ROS conventions:
uppercase alphanumeric characters with underscores for separating words
partially fix#19917
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
As per the discussion in #15331, fixed issue where stm32h7 chips
use hardware ECC bits in program memory that disallow overwriting
32-byte flash line that has already been written. As such,
this change allows for a variant implementation of the flashfs system
that uses more space in the flash entry header in order to
allow an entire line to be reserved for erasing an entry.
Signed-off-by: Taylor Nelms <tnelms@roboticresearch.com>
rtl state was getting reset on inactive, which meant that the state which triggered resuming e.g. mission landing would be overwritten, and the navigator mode would switch back and forth between rtl and mission. this commit:
1. moves the reset of rtl state to the on activation function (removing it from the on inactive function)
2. functionalizes the rtl state input to the rtl time estimator so that rtl time can still be calculated from state=none while inactive
This commit removes the additional airspeed check (airspeed for VTOLs in
hover below LNDFW_AIRSPD_MAX), as it is not a required condition in the
landed state (headwind blowing into the airspeed sensor won't stop
once on the gruond). In FW mode the check would make more sense, but there
the land detector is currently simply disabled.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- if using multi-EKF across all magnetometers then an instance of
vehicle_magnetometer is advertised immediately for every sensor_mag
instance
- this can become problematic if EKF2 multi-mag is enabled, but with
only 1 IMU (EKF2_MULTI_MAG) because you will be stuck with no magnetometer data
FW_LND_USETER defaulted to 1 and FW_LND_ABORT terrain based bits all enabled. why? because using a distance sensor is critical to detecting when to flare, and we want to force the user to actively disable these safety settings if they so choose, so that they understand the implications.
- new param, FW_LND_TER_REL
- fixing the glide slope helps keep the landing glide behavior steady (avoiding bumps in the altitude setpoint from e.g. trees)
- flare is still triggered via the distance sensor, if enabled by FW_LND_USETERR
when the vehicle did not track the slope well (e.g. at an offset above the track) and the altitude setpoint flattening on intersection with terrain, the throttle would spool up to smoothly intersect the newly flattened altitude setpoint, this could happen before the flare altitude was reached, which is bad. now the steady state glide behavior will be maintained, and flare can trigger at the appropriate time
- the target_sink_rate param could possibly constrain the maximum commanded sink rate to something less than that of the landing glide slope, which would make it impossible to track. this commit allows opening up the desired max sink rate up to the performance limits of the aircraft, if necessary, for the landing case
- landing slope/curve library removed
- flare curve removed (the position setpoints will not be tracked during a flare, and were being ignored by open-loop maneuvers anyway)
- flare curve replaced by simply commanding a constant glide slope to the ground from the approach entrance, and commanding a sink rate once below flaring alt
- flare is now time-to-touchdown -based to account for differing descent rates (e.g. due to wind)
- flare pitch limits and height rate commands are ramped in from the previous iteration's values at flare onset to avoid jumpy commands
- TECS controls all aspects of the auto landing airspeed and altitude/height rate, and is only constrained by pitch and throttle limits (lessening unintuitive open loop manuever overrides)
- throttle is killed on flare
- flare is the singular point of no return during landing
- lateral manual nudging of the touchdown point is configurable via parameter, allowing the operator to nudge (via remote) either the touchdown point itself (adjusting approach vector) or shifting the entire approach path to the left or right. this helps when GCS map or GNSS uncertainties set the aircraft on a slightly offset approach"
- refactor updateQuaternion() to compute the yaw jacobian directly (respecting the rotation sequence determination)
- fuseHeading()/fuseYaw321()/fuseYaw312() helpers are eliminated and now mag heading fusion and EV yaw fusion compute the innovation in place
- clear up logic for performing zero innovation heading fusion when quaternion variance exceeds threshold (no more _is_yaw_fusion_inhibited flag manipulation)
- when at rest continue fusing last static heading with very low variance even if other heading sources are active
We need to ensure the Dronecode logo is prominently displayed
and linked to the PX4 brand for trademark protection of PX4 and Dronecode.
If you have any questions about this, please feel free to reach out directly to me.
- post takeoff, the aircraft follows the infinite line sourced from the launch point in the direction of the takeoff waypoint
- takeoff waypoint altitude is used as a clearance altitude, set such that once above, the aircraft has cleared all ground occlusions and may proceed with the mission
- runway takeoff state machine simplified to throttle ramp, clamped to runway, climbout, and fly
- throttle ramp must complete before switching to next state to avoid a jump in throttle setpoint just after takeoff if the takeoff airspeed is reached before the ramp is complete
- roll constraints near ground post takeoff removed from runway takeoff class (handled externally now)
- minimum airspeed in TECS is reduced to takeoff speed (if necessary) to lower the underspeed detection bound
- lateral-directional guidance uses a different period parameter during ground roll
- apply constraint only for takeoff and landing modes
- add two params, wing span and wing height, to calculate a reasonable height at which roll limits can be opened
- takeoff situational knowledge removed from all other modes except manual (or actual takeoff mode)
- manual takeoff is marked complete if at a controllable airspeed
- minimum pitch bounds TECS until manual takeoff complete
- remove individual roll constraints during manual takeoff (ground proximity constraints coming in subsequent commit)
- underspeed condition only determined by true airspeed undershoot
- change binary underspeed condition to a continuous percent undersped
- ramp-in max throttle, pitch speed weight, and TAS setpoint reduction during underspeed to avoid jumpy commands at the true airspeed error boundary
- let true airspeed filter reach zero airspeed
- create integral and trajectory generator reset methods
- always run TECS unless in rotary-wing mode (or in transition)
- constantly reset TECS integrals and trajectory generators when landed
- simplify takeoff reset method
- removes _last_manual variable in favor of _skipping_takeoff_detection, which is handled in the control mode setter
- takeoff detection (both launch and runway) is skipped if entering takeoff mode from any other mode while having already been in the air
- added method to runway takeoff class for force setting the fly state when we want to skip the takeoff detection
- array length of data was increased without changing the data type of
the variable holding the length
Signed-off-by: RomanBapst <bapstroman@gmail.com>
As they are always moving horizontally, the check doesn't make sense
for fixed-wings.
Also don't run the check while on ground to prevent getting a failed
check during pre-takeoff manipulation.
- trim throttle is handled entirely by the position controller
- navigator should use speed setpoints
- added flag gliding_enabled in position setpoint to stills support gliding
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- allow compensation based on vehicle weight (parameterized)
- use density for calculating trim throttle compensation instead of pressure
- removed parameter FW_THR_ALT_SCL
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Make Power Off tune not interruptable
This solves the case of Low Battery warning tune overriding the power
off tune, as now the Power off tune is not interruptable by any other
tune unless override flag is specified
commander_helper: resolve "redundant boolean literal in ternary expression result"
- Existing code was hard to read and quite ambiguous
- Also it allowed constantly re-sending the tune_control request for a
fixed duration tunes like "TUNE_ID_BATTERY_WARNING_SLOW", while not
respecting the tune duration
When wind is already estimated, we don't reset the states using airspeed
data, so it could be that the fusion fails if the airspeed isn't
consistent with the filter (test ratio > 1). In this case, don't start
the fusion.
When wind isn't already estimated, the wind states are reset using
airspeed so the fusion can start regardless of the current test ratio.
- As it is always only used for the vehicle command ack message
- It was a duplicate, hence making it error prone for maintainment
- The uORB message comments were updated to make the relationship with
the MAVLink message / enum definitions clear
split the fusion process into:
1. updateAirspeed: computes innov, innov_var, obs_var, ...
2. fuseAirspeed: uses data computed in 1. to generate K, H and fuse the
observation
from 300 ms to 60 seconds, to give enough time for the user to configure
the vehicle in the mean time.
This is needed especially when the battery cell count setting is wrong
(when it should be 3, but set to 4 for example), since then whenever you
boot the vehicle, it will shutdown after 300 ms, which leaves the user
puzzled as to exactly what's happening. And it also prevented the user
from changing the Parameter since it's shutting down so quickly.
60 second window is intended to be a reasonable time that will allow the
user to figure out what's going on (via checking the battery level on
QGC, etc) but also not deep discharge the battery to a dangerous level.
Fixes the error:
Aborting due to missing @type tag in file: 'build/px4_fmu-v5_test/etc/init.d/airframes/11001_hexa_cox'
This can happen due to a change to e.g. board_serial_ports, which changes
the CLI command and triggers a re-execution of the airframe processing.
- this allows landing gear to retract automatically when doing a takeoff
and the vehicle is considered high enough
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- 4096 of 3 hex digits each for rev and ver is enough.
#defines used in SPI versions do not be long format, use use the macro
- Board provides a prefix and the formatting is sized and built in
- No need for funky board_get_base_eeprom_mtd_manifest interface
Original mft is used where the abstraction is done with the MFT interface
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
If the capture GPIO is exposed to a signal with high frequency changes, a lot of
interrupts are scheduled and the handling of these call can worst-case
starve flight critical processes leading to a loss of control. Since camera capture
is not flight critical, we now give up the capture
functionality and stop the interrupts to prevent the starvation of other processes.
If the PPS GPIO is exposed to a signal with high frequency changes, a lot of
interrupts are scheduled and the handling of these calls can worst-case
starve flight critical processes leading to a loss of
control. Since PPS is not flight critical, we now give up the PPS
functionality and stop the interrupts to prevent the starvation of other processes.
Remove the entire external yaw handler, dynamic memory allocation,
pointer passing logic. Directly instanciate the weather vane instance
in the flight tasks that support it.
- remove internal accumulation and publish every valid raw sample synchronized with sensor
- store timestamp_sample from motion interrupt
- improve timing requirements from datasheet (minimum delays after register read/write)
- remove internal accumulation and publish every valid raw sample synchronized with sensor
- store timestamp_sample from motion interrupt
- improve timing requirements from datasheet (minimum delays after register read/write)
- all sources of optical flow publish sensor_optical_flow
- sensor_optical_flow is aggregated by the sensors module, aligned with integrated gyro, and published as vehicle_optical_flow
Co-authored-by: alexklimaj <alex@arkelectron.com>
Follow me : tidied second order filter implementation
Added velocity filtered info to uORB follow target status message, and rebase to potaito/new-follow-me-task
FollowMe : Rebasing and missing definition fixes on target position second order filter
Follow Me : Remove Alpha filter delay compensation code, since second order filter is used for pose filtering now
Followme : Remove unused target pose estimation update function
Follow Target : Added Target orientation estimation logic
Follow Target : Replaced offset vector based setpoint to rate controlled orbital angle control
Follow Target : Bug fixes and first working version of rate based control logic, still buggy
Follow Target : Added target orientation, follow angle, orbit angle value into follow_target_status uORB message for debugging
Follow Target : Fix orbit angle step calculation typo bug
Follow Target : Few more fixes
Follow Target : Few fixes and follow angle value logging bug fix
Follow Target : Added lowpass alpha filter for yaw setpoint filtering
Follow Target : Remove unused filter delay compensation param
Follow Target : Add Yaw setpoint filter initialization logic and bufix for when unwrap had an input of NAN angle value
Follow Target : Add Yaw setpoint filtering enabler parameter
Follow Target : Change Target Velocity Deadzone to 1.0 m/s, to accomodate walking speed of 1.5 m/s
Follow Target : Add Orbit Tangential Velocity calculation for velocity setpoint and logging uORB topics
Follow target : Fix indentation in yaw setpoint filtering logic
Follow Target : Fix Follow Target Estimator timeout logic bug that was making the 2nd order pose filter reset to raw value every loop
Follow Target : Remove debug printf statement for target pose filter reset check
Follow Target : Add pose filter natural frequency parameter for filter testing
Follow Target : Make target following side param selectable and add target pose filter natural frequency param description
Follow Target : Add Terrain following altitude mode and make 2D altitude mode keep altitude relative to the home position, instead of raw local position origin
Follow Target : Log follow target estimator & status at full rate for filter characteristics test
Follow Target : Implementing RC control user input for Follow Target control
Follow Target : edit to conform to updated unwrap_pi function
Follow Target : Make follow angle, distance and height RC command input configurable
Follow Target : Make Follow Target not interruptable by moving joystick in Commander
Follow Target : reconfigure yaw, pitch and roll for better user experience in RC adjusting configurations, and add angular rate limit taking target distance into account
Follow Target : Change RC channels used for adjustments and re-order header file for clarity
Follow Target : Fix Parameters custom parent macro, since using DEFINE_PARAMETERS alone misses the parameter updates of the parent class, FlightTask
Follow Target : Fix Orbit Tangential speed actually being angular rate bug, which was causing a phenomenon of drnoe getting 'dragged' towards the target velocity direction
Follow Target : Final tidying and refactoring for master merge - step 1
Add more comments on header file
Follow Target : tidy, remove unnecessary debug uORB elements from follow_target_status message
Follow Target : Turn off Yaw filtering by default
Follow Target : Tidy maximum orbital velocity calculation
Follow Target : add yaw setpoint filter time constant parameter for testing and fix NAV_FT_HT title
Follow Target : Add RC adjustment window logic to prevent drone not catching up the change of follow target parameters
Follow Target : fixes
Follow Target: PR tidy few edits remove, and update comments
Follow Target : apply comments and reviews
Follow Target : Edit according to review comments part 2
Follow Target : Split RC adjustment code and other refactors
- Splitted the RC adjustment into follow angle, height and distance
- Added Parameter change detection to reset the follow properties
- Added comments and removed yaw setpoint filter enabler logic
Follow Target : Modify orbit angle error bufferzone bug that was causing excessive velocity setpoints when setpoint catched up with raw orbit setpoint
Follow Target : Remove buffer zone velocity ramp down logic and add acceleration and rate limited Trajectory generation library for orbit angle and velocity setpoint
Follow Target : Remove internally tracked data from local scope function's parameters to simplify code
Follow Target : Fix to track unwrapped orbit angle, with no wrapping
Follow Target : Apply user adjustment deadzone to reduce sensitivity
Follow Target : Apply suggestions from PR review round 2 by @potaito
Revert submodule update changes, fall back to potaito/new-followme-task
Follow Target : [Debug] Expose max vel and acceleration settings as parameters, instead of using Multicopter Position Controller
's settings
Follow Target : Use matrix::isEqualF() function to compare floats
Follow Target : Add Acceleration feedback enabler parameter and Velocity ramp in initial commit for overshoot phenomenon improvement
Follow Target : Implement Velocity feed forward limit and debug logging values
Follow Target : Apply Velocity Ramp-in for Acceleration as well & Apply it to total velocity setpoint and not just orbit tangential velocity component
Follow Target : Don't set Acceleration setpoint if not commanded
Follow Target : Use Jerk limited orbit angle control. Add orbit angle tracking related uORB values"
Follow Target : Add Orbit Angle Setpoint Rate Tracking filter, to take into consideration for calculating velocity setpoint for trajectory generator for orbit angle
Revert "Follow Target : Add Orbit Angle Setpoint Rate Tracking filter, to take into consideration for calculating velocity setpoint for trajectory generator for orbit angle"
This reverts commit a3f48ac7652adb70baf3a2fed3ea34d77cbd6a70.
Follow Target : Take Unfiltered target velocity into acount for target course calculation to fix overshoot orbit angle 180 deg flip problem
Follow Target : Remove Yaw Filter since it doesn't make a big difference in yaw jitterness
Follow Target : Remove velocity ramp in control & remove debug values from follow_target_status.msg
Follow Target : Tidy Follow Target Status message logging code
Follow Target : Remove jerk and acceleration settings from Follow Target orbit trajectory generation
Follow Target : Change PublicationMulti into Publication, since topics published are single instances
Follow Target : Edit comments to reflect changes in the final revision of Follow Target
Follow Target : Apply incorrectly merged conflicts during rebase & update Sticks function usage for getThrottled()
Follow Target : Apply final review comments before merge into Alessandro's PR
Apply further changes from the PR review, like units
Use RC Sticks' Expo() function for user adjustments to decrease sensitivity around the center (0 value)
Update Function styles to lowerCamelCase
And make functions const & return the params, rather than modifying them
internally via pointer / reference
Specify kFollowPerspective enum as uint8_t, so that it can't be set to negative value when converted from the parameter 'FLW_TGT_FP'
Fix bug in updateParams() to reset internally tracked params if they actually changed.
Remove unnecessary comments
Fix format of the Follow Target code
Fix Follow Perspective Param metadata
follow-me: use new trajectory_setpoint msg
Convert FollowPerspective enum into a Follow Angle float value
1. Increases flexibility in user's side, to set any arbitrary follow
angle [deg]
2. Removes the need to have a dedicated Enum, which can be a hassle to
make it match MAVSDK's side
3. A step in the direction of adding a proper Follow Mode (Perspective)
mode support, where we can support kite mode (drone behaves as if it is
hovering & getting dragged by the target with a leash) or a constant
orbit angle mode (Drone always on the East / North / etc. side, for
cinematic shots)
Continue fixing Follow Target MAVSDK code to match MAVSDK changes
- Support Follow Angle configuration instead of Follow Direction
- Change follow position tolerance logic to use the follow angle
*Still work in progress!
Update Follow Me MAVSDK Test Code to match MAVSDK v2 spec
- Add RC Adjustment Test case
- Change follow direction logic to follow angle based logic completely
- Cleanup on variable names and comment on code
follow-me: disable SITL test
Need to update MAVSDK with the following PR:
https://github.com/mavlink/MAVSDK/pull/1770
SITL is failing now because the follow-me
perspectives are no longer defined the
same way in MAVSDK and in the flight task.
update copyright year
follow-me: mark uORB topics optional
Apply review comments
more copyright years
follow-me sitl test: simpler "state machine"
flight_mode_manager: exclude AutoFollowTarget and Orbit on flash contrained boards
Remove unnecessary follow_target_status message properties
- As it eats up FLASH and consumes uLog bandwidth
rename follow_me_status to follow_target_status
enable follow_target_estimator on skynode
implement the responsiveness parameter:
The responsiveness parameter should behave similarly to the previous
follow-me implementation in navigator. The difference here is that
there are now two separate gains for position and velocity fusion.
The previous implemenation in navigator had no velocity fusion.
Allow follow-me to be flown without RC
SITL tests for follow-me flight task
This includes:
- Testing the setting for the follow-me angle
- Testing that streaming position only or position
and velocity measurements both work
- Testing that RC override works
Most of these tests are done with a simulated model
of a point object that moves on a straight line. So
nothing too spectacular. But it makes the test checks
much easier.
Since the estimator for the target actually checks new
measurements and compares them to old ones, I also added
random gausian noise to the measurements with a fixed seed
for deterministic randomness. So repeated runs produce
exactly the same results over and over.
Half of the angles are still missing in MAVSDK. Need to create
an upstream PR to add center left/right and rear left/right options.
These and the corresponding SITL tests need to be implemented
later.
sitl: Increase position tolerance during follow-me
Astro seems to barely exceed the current tolerance (4.3 !< 4.0)
causing CI to fail. The point of the CI test is not to check
the accuracy of the flight behaviour, but only the fact that the
drone is doing the expected thing. So the exact value of this
tolerance is not really important.
follow-me: gimbal control in follow-me
follow-me: create sub-routines in flight task class
follow-me: use ground-dist for emergency ascent
dist_bottom is only defined when a ground facing distance sensor exist.
It's therefore better to use dist_ground instead, which has the distance
to the home altitude if no distance sensor is available.
As a consequence it will only be possible to use follow-me in a valley
when the drone has a distance sensor.
follow-me: point gimbal to the ground in 2D mode
follow-me: another fuzzy msg handling for the estimator
follow-me: bugfix in acceleration saturation limit
follow-me: parameter for filter delay compensation
mantis: dont use flow for terrain estimation
follow-me: default responsiveness 0.5 -> 0.1
0.5 is way too jerky in real and simulated tests.
flight_task: clarify comments for bottom distance
follow-me: minor comment improvement
follow-me: [debug] log emergency_ascent
follow-me: [debug] log gimbal pitch
follow-me: [debug] status values for follow-me estimator
follow-me: setting for gimbal tracking mode
follow-me: release gimbal control at destruction
mavsdk: cosmetics 💄
Symmetric buffers allow a much more reliable QGC Wifi telemetry connection especially when (virtual) joysticks are used. (this board does not provide RX DMA on UART 4 as its timer does DSHOT).
The noise spectral density, NSD, (square root of power spectral density) is a
continuous-time parameter that makes the tuning independent from the EKF
prediction rate.
NSD corresponds to the rate at which the state uncertainty increases
when no measurements are fused into the filter.
Given that the current prediction rate of EKF2 is 100Hz, the
same tuning is obtained by dividing the std_dev legacy parameter by 10:
nsd = sqrt(std_dev^2 / 100Hz)
The noise spectral density, NSD, (square root of power spectral density) is a
continuous-time parameter that makes the tuning independent from the EKF
prediction rate.
NSD corresponds to the rate at which the state uncertainty increases
when no measurements are fused into the filter.
Given that the current prediction rate of the wind estimator is 1Hz, the
same tuning is obtained with the same values as before.
1. Rename *_header_s structs to *_s, since the _header postfix is not
helpful
2. Rename the "key" string variables in the message structs to
"key_value_str" as the string actually contains not just the key but the
key and value pair information
3. Add comments on other uLog messages to clarify use (need more
improvement / can be even more simplified)
* sih: Move sih out of work queue
This reverts commit bb7dd0cf00.
* sih-sim: Enable sih in sitl, together with lockstep
* sih-sim: new files for sih: quadx and airplane
* sih: Added tailsitter for sih-sitl simulation
* sitl_target: Added seperate target loop for sih
* jmavsim_run: Allow jmavsim to run in UDP mode
* lockstep: Post semaphore on last lockstep component removed
* sih-sim: Added display for effectively achieved speed
* sih: increase stack size
* sih-sim: Improved sleep time computation, fixes bug of running too fast
* sitl_target: place omnicopter in alphabethic order
Co-authored-by: romain-chiap <romain.chiap@gmail.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
- documentation of units, params, returns, and descriptions for variables and methods
- rename ambiguous or erroneous state variables
- remove unused or unecessary input arguments to functions
- remove ugly header white space
The safetyButtonHandler() reports that the safety statatus
changed on the first loop iteration when safety is disabled which makes
sense to inform the system that safety is off but the tune for the user
should not be played because it interrupts the startup tune.
They cause problems with building px4_msgs in ROS2 Humble Hawksbill and removing them fixes the issue.
Co-authored-by: Agata Barcis <agata.barcis@tii.ae>
This corrects the board definition to use the proper polarity
for the brick power valid signal, thus allowing the board to
detect the battery and monitor it properly.
internal PX4IO safety_off state is removed and replaced with a normal safety button event. From this 'commit' commander is taking care of the PX4IO safety.
- on common IMUs like the mpu6000, mpu9250, icm20602, etc each FIFO
sample is only 12 bytes so this is still more than large enough for the
worst case transfer
- free memory is getting tight on these older boards (depending on
configuratoin) and the pixhawk 2 cube still has 2 other superior IMUs, so this is just
dropping dead weight
H7 Only supports 2 not 3 CAN interfaces.
CanInitHelper passes in in the run time configuration of
the number of interfaces. The code was ignoring these!
This type (23) doesn't specify a motor number, so it can't be properly handled.
There are duo (19) and quad (20) tailsitter types that still work in simulation.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Based on feedback that very often the battery is used down too low.
I observed this happens consistently when the cell voltage is properly
load compensated. The default load compensation before #19429 was very
inaccurate and resulted in unpredictable estimate.
After that if there is a usable current measurement and the battery is
within expected tolerances of the default internal resistance the
compensation is pretty good and 3.5V is too low for an empty compensated
cell voltage. That was seen in various logs where the compensated
cell voltage was already dropping fast after 3.6V.
In case the voltage is not load compensated the vehicle estimates the
state of charge a bit too low which is safer than to high
especially for a default configuration.
internal PX4IO safety_off state is removed and replaced with a normal safety button event. From this 'commit' commander is taking care of the PX4IO safety.
Without this, uavcan creates MixingOutput classes which then create
empty actuator_outputs publications. This then prevents the motor
output in HITL to be forwarded to the simulator via mavlink.
The baro observation noise parameter is often over-estimated in order as
a measure to mitigate temporary offsets in the readings due to wind
gusts or poor pressure compensation tuning. The side effect is that the
innovation sequence monitoring based on normalized innovation struggles
to detect an offset in the state because the innovation isn't
statistically significant.
To counter this issue, a simpler check is added to trigger the process
noise boost when the innovation has the same sign for a long period of
time.
1. Change the paragraph headings to proper Markdown headings (easier to
link / structure the Markdown)
2. Move PULL_REQUEST_TEMPLATE into .github folder
3. Change description in Issue template and remove outdated DevGuide
Repository information
4. Add a bug emoji to bug report isue template
5. Support automatically adding labels 'bug-report' and
'feature-request' to easily sort / filter appropriate issues in Github
We use lockdown to prevent outputs like motors and servos from being
active in HITL simulation. This means that we can't treat the lockdown
flag as a flight_terminated, otherwise we can't arm in HITL at all.
I got multiple times the feedback now that a consistent delay
is helpful and makes sense but the default delay
is too long
for low battery action where you're trying to come back in time
and possibly the emergency reaction kicks in while the critical action
is executing which leads to a longer accumulated delay.
To return Exponential Values, which is helpful for reducing the
sensitivity of the stick around the centered value (0), since it's
exponential curve.
Useful for user adjustment implementations, where accidentally touching the stick
wouldn't have so much effect when using the Exponential value, compared
to using the raw position value.
This fixes an invalid memory access when exiting the module:
exit_and_cleanup destroys the object, but lock_guard is destructed after
and accesses the lock.
- limit to handling only 1 motor failure
- Log which motor failures are handled
- Remove motor from effectiveness matrix without
recomputing the scale / normalization
- this allows jumping straight to a non-SBUS RC protocol
- increased the scan time per protocol 300->500 ms, which the newer DSM parser seems to need in some cases.
- only set RC_INPUT_PROTO if we've had a successful RC lock for > 3 seconds
Normally _should_run for mission is only ever true if _should_run for the
normal log is. There are exceptions though:
- the log buffer fails to allocate
- there was a write failure (e.g. due to SD card removal)
In that situation, the writer would not wait anymore but busy-loop.
This replaces the propeller_torque_disabled flag to disable yaw by differential thrust
for tiltrotor and tailsitter VTOLs, as propeller_torque_disabled is not enough to set
effectiveness of an acutator in the yaw axis to 0 in case it's tilted.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Special case tiltrotor: instead of passing a 3D thrust vector (that would mostly have a x-component in FW, and z in
MC), pass the vector magnitude as z-component, plus the collective tilt. Passing 3D thrust plus tilt is not feasible as they
can't be allocated independently, and with the current controller it's not possible to have collective tilt calculated
by the allocator directly.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The flight termination action on geofence violation is described as only trigger, when the corresponding circuit breaker is not disabled. However, the description of the circuit breaker states, that the geofence action is not depedning on this circuit breaker. The implementation follows the description of the circuit breaker. Hence the GF_ACTION description is adapted.
- add logic for detecting high wind speed in Commander,
and handle it toghether with wind speed warning
- trigger and enforce RTL if COM_WIND_MAX is breached
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Adds COM_FLT_TIME_MAX param and logic in Commander to enforce RTL when
flight time is above this value. User can only override to LAND mode,
but not proceed flight beyond that.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
If both local position and altitude were not valid, then both RC loss and
datalink loss would not trigger any failsafe at all, independently from
the configured action.
Calculating K(HP) takes less operations than (KH)P because K and H are
vectors.
Without considering the sparsity optimization:
- KH (24*24 operations) is then a 24x24 matrix an it takes
24^3 operations to multiply it with P. Total: 14400 op
- HP (24*(24+24-1) operations) is a row vector
and it takes 24 operations to left-multiply it by K. Total:1152 op
This is a combination of the originally introduced delay:
06c10f61c1
then the emergency failsafe being changed to not just land,
position control being rescheduled to not overwrite every setpoint in:
e502214429576ce68ac3fee9d2db19112f4604b9
and it being fixed by overwriting the setpoint but not removing
the long obsolete hystersis here:
114e85d260
- remove separate flaperon controls input to mixer instead enable spoiler support
- add slew rate limiting on both flap and spoiler controls
- add spoiler configuration for Landing and Descend
- add trimming from spoiler deflection
- FW Attitude control: remove FW_FLAPS_SCL param -->
The flap settings for takeoff and landing are now specified relative to full range.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
[4] is reserved for Flaps, so also having the tilt on it was preventing us from
using flaps on tiltrotors, and other ripple effects.
By using [8] the tilt is separated from all other channels - it requires to increase the size of
actuator_controls by 1 to 9.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
There was a time window where if a task with higher priority than the main
logger thread would busy-loop, it would block both logging threads and the
watchdog would not trigger if the writer was in idle state.
This can happen for fast SD card writes.
when the vertical pos or vel innov ratio is above the threshold, the
other one needs to be significant too and not just positive to trigger
the failure
- on some H7 boards (cuav x7pro tested) there's an occasional hard fault when starting the mavlink shell that is no longer reproducible with the slightly expanded locking
- this is likely just changing the timing (holding the sched lock for longer), but this should be harmless for now until we can identify the root cause
Weather vane should only set a yawrate setpoint, but no yaw setpoint.
Setting it to NAN when WV is active makes sure that whatever _yaw_setpoint
is set previously (e.g. through Waypoint) is not used.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- set local home using global pos and global home
- set local home using GNSS pos and global home
- set global home using global ref of local frame and local home
This is to make clear that the relevant part of the home position
message for navigator is the global one. Local home position isn't
required as everything is done in global coordinates.
The specific home_alt_valid is used when lat/lon are not used
- always try to set local or global home position when possible
- set global home with GNSS position if global pos from EKF isn't
available
- reset home when significantly moved from home before takeoff (checking
lpos or gpos or GNSS)
- reset home on takeoff transition
- reset home on mavlink arm command
- remove "home required accuracy" parameters, rely on validity flags
- fixes the deadlock in px4io ioctl mixer reset
- px4io Run() locks (CDev semaphore)
- mixer load goes through px4io ioctl MIXERIOCRESET which calls MixingOutput::resetMixerThreadSafe()
- MixingOutput::resetMixerThreadSafe() stores a Command::Type::resetMixer command in an atomic variable, schedules a work queue cycle, then sleep spins until the command is cleared
- the execution of the cycle eventually calls back into PX4IO::updateOutputs(), which tries to lock (and waits forever)
- most px4_io-v2 boards have a blue LED that breathes for status
- the pixhawk 2.1 (hex) re-used this blue LED for as an IMU heater (active low), but kept the same board id (so we have to detect at runtime)
- the new cubepilot boards (yellow, orange) inverted the polarity of this heater pin
- untangle the mess slightly so that things we know statically (eg cubepilot cubeorange LEDs and heater polarity) are handled at build time.
To pass from invalid to valid:
- time hysteresis
- some vertical velocity
- test ratio < 1
- low-passed signed test ratio < 1
To pass from valid to invalid:
- low-passed signed test ratio >= 1
At each new valid range measurement, the time derivative of the distance
to the ground is computed and compared with the estimated velocity.
The average of a normalized innovation squared statistic check is used
to detect a bias in the derivative of distance measurement,
indicating that the distance measurements are kinematically inconsistent
with the filter.
For many VTOLs/fixed-wing drones a 50m loiter radius is too tight, and
going to 80m is a better and safer default.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- In this case, no action is configured for datalink lost. Action is configured for RC lost.
- In case of no data link and no rc failsafe is enabled but reporting a "no_datalink" reason but "no_rc_and_no_datalink" seems more explicit.
- previously an invalid decode would continue to be transferred to the FMU (at 50 Hz) and published to the rest of the system as successfully decoded new RC data
- by only publishing new successful decodes we can more effectively discard invalid data in downstream consumers
PX4 supports int32 parameter types by interpreting the 32 bits in
the float field as an int32 field. To signal this behaviour, it should
set the bit which is described as PARAM_ENCODE_BYTEWISE.
PX4 had always handled parameters this way but never actually sent the
capability (which back then was called PARAM_UNION), however, it should
have. This came up recently in the MAVLink devcall when these flags were
discussed. The takeaway was to remove the flags to make it clearer and
to make sure the projects (like PX4) send them out correctly.
mathlib: add second order reference model filter with optional rate feedback (#19246)
Reference models can be used as filters which exhibit a particular, chosen (reference) dynamic behavior. This PR implements a simple second order transfer function which can be used as such a reference model, additionally with rate feedback. The system is parameterized by explicitly set natural frequency and damping ratio. Another nice externality is that the output state and rate are kinematically consistent. Forward-euler and bilinear transform discretizations for the state space integration step are available.
- introduce BAT_AVRG_CURRENT param that is used for init of average current estimate
- increase filtering of average current estimation
- only update average current filter when armed
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This fixes unspecified behaviour due to evaluation order of args.
It's up to the compiler whether next_number() or next_dots() is executed
first which means that the behaviour is not properly specified.
- sensor_baro.msg use SI (pressure in Pascals)
- update all barometer drivers to publish directly and remove PX4Barometer helper
- introduce baro cal (offset) mainly as a mechanism to adjust
relative priority
- commander: add simple baro cal that sets baro offsets to align with
GPS altitude (if available)
- create new sensors_status.msg to generalize sensor reporting
- things like arming requests can be dependent on current nav state
that might requested by a previous command, but the state machine
transition will only happen after command processing
- new static notch filter configured via IMU_GYRO_NF1_FRQ and IMU_GYRO_NF1_BW
- existing notch parameters IMU_GYRO_NF_FREQ and IMU_GYRO_NF_BW become
IMU_GYRO_NF0_FRQ and IMU_GYRO_NF0_BW
- when estimating the peak frequency the magnitude of side buckets will
be factored in, so it doesn't make sense to potentially treat them as
separatey detected peaks
- set MAV_TYPE as a parameter default per vehicle type, or airframe if necessary
- cleanup MAV_TYPE param metadata and commander helper to only include
what's currently used in PX4
It accesses kernel internal structures directly; this needs to be
worked out with some proper userspace-kernel interface
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is needed for DMA capable memory for fat also in the user side;
the file system doesn't seem to work reliably without.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For protected/kernel builds the cxx static initializations
needs to be done also in kernel side, since px4 creates
c++ objects in kernel
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Implement an interface for protected build to access parameters.
The implementation only does IOCTL calls to the kernel, where the parameters
live.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Put all functions which are commont to flat build and protected kernel and
userspace to an own source file
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- the estimated mag bias was requiring > 30 seconds of continuous 3d
mag fusion to be reported stable (and saved back to mag cal), this
restores the original intent requiring 30 seconds of accumulated valid
3d mag fusion
Need to log both, because on some systems the
information will come in directly as a
landing_target_pose message, and on others
it's coming in as irlock_report and then filtered
in PX4 to produce the landing_target_pose message.
- this was an experiment to casually monitor sensor offsets relative to temperature, but now that all calibration offsets can be adjusted post-flight the stored temperature can be misleading
- deleting to save a little bit of flash (and storing the temperature wasn't useful)
Otherwise the setpoint from weather vane is constantly overwritten by it,
even if the yaw stick is not moved.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This adds a nuttx userspace interface for hrt driver, communicating with
the actual px4 hrt driver via BOARDCTL IOCTLs
This is be used when running PX4 in NuttX protected or kernel builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Before, adding the pusher to the same matrix as the upwards motors affected
the scaling for the upwards motors, resulting in values not equal to -1
anymore.
Move some logic from Subscriber into uORBManager. This reduces calls from the
modules to the uORB manager, improving performance in protected build.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- this is a more conservative default if a vehicle isn't set (no land detector running)
- handled horizontal preflight failures in commander when disarmed
rather than overloading xy_valid and v_xy_valid flags
- ekf2 no longer depend on arming or standby status
- ekf2: expose dead reckoning as control status flags
- commander:
- add GPS validity check
- in AUTO MISSION if dependent on GPS then a loss of GPS will
- Also use the delayed current data instead of newest that might not be
available (gps buffer is sometimes empty if the dt between samples is
larger than the delayed horizon).
- Separate "baro fault" from "baro intermittent": intermittent is a
temporary failure and should prevent from switching to baro right now,
but "fault" means that it should never be used anymore
- In case of height timeout, check for metrics but not for consistency
as the filter is likely to have diverged already.
* Adds Timer15 to stm32_common, if the timer base is defined
* Adds Timer15 logic for DMA and AltFunc config on stm32h7 boards
* Adds TIM15 BDTR->MOE support in stm32_common timer init
* Adds support for TIM15 pwm channels on Matek H743 Slim
If the hardware support RESET lockout that has nArmed ANDed with VBUS
vbus_sense may drop during a param save which uses
BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE to prevent external resets
while writing the params. If we are not armed and nARMRED is low
we are in such a lock out so ignore changes on VBUS_SENSE during this
time.
Once we have valid input we should use that and not overwrite our
update_result with the result from other inputs, otherwise the
automatic selection does not actually work.
This behavior means that only the first update will be used if there are
several sources updating in the same cycle.
It was a mistake to mix these two together, it is simpler to implement the boardctl interface
for the protected build, if the boardctl ioctls are different
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds an ioctl interface for NuttX protected build, allowing
system calls from user space to kernel for uORB, HRT and crypto
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Weak authority on a axis is currently defined as: none of the actuators have an
effectivness on this particular axis larger than 0.05.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Navigator: enable DO_CHANGE_SPEED for outside of mission
- update _mission_cruising_speed_mc/_fw also if DO_CHANGE_SPEED command
is received outside of mission (e.g. while Loitering doing an Orbit)
- if vehicle is in AUTO_LOITER when receiving the change speed, then immediately
apply it by doing a reposition without updating any other field than cruising_speed
and cruising_throttle
-when RTL is activated reset the cruising speed and throttle
* Navigator: reset cruise speed and throttle to default when VTOL-transitioning
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
-pass flag EffectivenessUpdateReason into effectiveness, indicating if there was an external
update or not. Reasons for external updates are:
-config changes (parameter)
-motor failure detected or certain redundant motors are switched off to save energy
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When building uORB for NuttX flat build, or for some other target, everything
works as before.
When building uORB for NuttX protected or kernel build, this does the following:
- The kernel side uORB library reigsters a boardctl handler for calls from userspace
and services the boardctl_ioctls by calling the actual uORB functions
- For user mode binaries, the uORBManager acts as a proxy, making boardctl_ioctl calls to the
kernel side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This fixes the issue when changing the altitude during a goto for
example, where the vehicle was going backwards and upwards to reach the
closest point to the line. Now the vehicle simply goes towards the
target waypoint.
- RC_PORT_CONFIG is disabled by default if the board doesn't have
CONFIG_BOARD_SERIAL_RC set
- allows user facing custom RC configuration that overrides board
defaults
This is the case for boards with digital readout, like v5x, but still
enable the battery_status module for external analog driver options.
An alternative would be to not run battery_status depending on config.
This saves a lot of flash space, in case functions from libtomcrypt
are not used (currently only RSA related).
When RSA is not used, the linker can now drop all libtomcrypt related things.
This is especially relevant for bootloaders using the SW crypto.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
* Make board_id compatible with ardupilot
* Initialize outputs for CAM1/CAM2 and Vsw pad
* Correct board type 1013 in bootloader to match AP
* Change usb vendor string to "Matek"
* Change cdcacm pid to 1013
* Comment out FLASH_BASED_PARAMS because of #15331
This is a bigger refactor of vmount to clean it up and plug some holes
in functionality.
The changes include:
- Fixing/simplifying the test command.
- Changing the dependencies of the input and output classes to just the
parameter list.
- Adding a separate topic to publish gimbal v1 commands to avoid
polluting the vehicle_command topic.
- Removing outdated comments and author lists.
- Extracting the gimbal v2 "in control" notion outside into control_data
rather than only the v2 input.
If we receive gimbal_device_attitude_status by mavlink we should not
re-send it as we are already supposed to be forwarding mavlink traffic
from the gimbal to the ground station.
For fixedwings, the orbit status was publishing zero radius when a goto waypoint was being passed.
This commit corrects this by passing the default loiter radius as the guidance logic was using
This addes the command serial_passthru which will pass data from one
device to another. This can be used to use u-center connected to USB
with a GPS on a serial port.
Usage: serial_passthru [arguments...]
-e <val> External device path
values: <file:dev>
-d <val> Internal device path
values: <file:dev>
[-b <val>] Baudrate
default: 115200
[-t] Track the External devices baudrate on internal device
With the -t option baudrate changes made on the PC connected to the USB
will be set to the intrenal device.
SD is on SPI3 - correct pin mapping
Fix DMA Mapping for all SPI and RX DMA on U[S]ART RX
Fix Memory MAP SRAM size
Removed unused GPIO
Used proper I2C definitions
Ensure Watchdog is configured for debugging
Fixed FLASH param definitions
Removed unedded SPI init
matek_gnss-m9n-f4:Correct Board ID and Size
Build order SJF
Added Support for F40x
- move vehicle at reset detection ekf2 -> land_detector
- ekf_unit: reduce init period
- Fake fusion is when at rest is quite strong and makes the variance reduce rapidly. Reduce the amount of time we wait before checking if the variances are still large enough.
- ekf_unit: reduce minimum vel/pos variance required after init
- Fake pos fusion has a low observation noise, making the vel/pos variances reduce quickly.
Co-authored-by:: bresch <brescianimathieu@gmail.com>
The stackcheck build flash space overflows after adding hygrometers.
Also follow the naming convention of other similar config flags, and rename the
config.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Split the px4_layer into user and kernel space libraries. Add some stubs for
user-space (e.g. version) where an interface to the kernel needs to be added
Use posix-versions for cpuload.cpp and print_load.cpp for userspace; these link to nuttx internals. This functinality could be built on top of posix (e.g. procfs) interfaces
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- remove class _mag_sample_delayed
- update mag fusion call graph to use mag sample delayed functionally
- Ekf::resetMagHeading()
- use low pass mag directly, but check if valid (magnitude)
- MAG_FUSE_TYPE_INDOOR treat like auto if heading required
If the board supports encrypting logfiles, but the parameter SDCARD_ALGORITHM is set to NONE,
the log should be written to the sdcard in plaintext format. This fixes a bug which caused
logger to hang in mutex instead.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Don't link to px4_layer
- Don't link to flashparams; flashparams would work only in kernel side
- Add missing link to px4_platform
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This goes the other way around; arch_io_pins is using the pin
definitions from drivers_board, so the drivers_board needs to be linked
into arch_io_pins
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Since uORB is split into kernel and userspace parts, it is no longer possible to just
link uORB into px4_platform, which is used in both kernel and user side.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Define __KERNEL__ macro during compilation and place the module in separate library
Remove default library linking to m or libc on NuttX. Add these in platform layer instead, since
they are different on kernel and user side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The needed version specific things come from px4 layer. Since version
is used both in kernel an user sides in protected build, it can't directly
link to drivers_board
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For NuttX protected or kernel build, the prebuilds can't contain libraries which are
different for kernel and user-space in protected/kerenl builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- introduces new parameter EKF2_PREDICT_US to configure the filter
update period in microseconds
- actual filter update period will be an integer multiple of IMU
This is done by inheriting from FlightTaskManualAltitudeSmoothVel again.
The altitude change by command is taken care of by switching
to the apporach when the altitude difference is big enough and
switching back once the altitude is close enough.
The altitude of the command is not perfectly reached but this can
only be done smoothly when the Orbit has full control over the
altitude smoothing. The independent altitude smoothing is not kept
because it was lacking stick handling like altitude lock and smooth
transitions when opening and closing the vertical position loop.
I think they were forgotten and it leads to side effects:
- The acceleration feed-forward does not get executed
- The acceleration setpoint is NAN when initializing the altitude
smoothing when arriving at the circle
The existing logic using the angle between velocity vectors failed to
determine a yaw failure in practice because the state velocity is often
too small compared to its uncertainty to be used. In all the failures
reported, the yaw emergency estimator converged properly and yaw reset
would have fixed the issue.
A much simpler check using the yaw difference between the main EKF
and the emergency estimator is now used to tell if the vel/pos update
failure is most likely caused by a wrong heading.
-rename FW_POSCTL_INV_ST to FW_POS_STK_CONF and make bitmask out of it:
- bit 0: alternative mapping (height rate on throttle stick, airspeed on pitch)
- bit 1: enable/disable airspeed setpoints via stick
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Take into account the actual number of roll and pitch acutators,
instead of assuming that all actuators have a roll/pitch component.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The forced flag is used to distinguish between updates due to a configuration
(parameter) change (only enabled when disarmed), and matrix updates due to motor
tilt change. Only update the normalization scale if the forced flag is true, and
use a tilt angle of vertical position for it to have the scales tilt-invariant.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
known issues:
- flash-based params does not work on H7 (due to ECC), so params are on
SD card. The last flash sector is still reserved however.
- output channel 6 does not support DShot (the implementation does not
handle channel gaps)
- flashing of the 2. flash bank is much slower (around 3x), than the 1.
bank for some unknown reason.
- after the BL jumps to the app, there's several seconds passing until
stm32_boardinitialize() is called.
and remove the possibility to set min > max to reverse.
Initially the idea was to add the checkbox on the UI side, to avoid adding
another param, but I don't think I'll go through the extra effort on the
QGC side.
I don't think the PX4 setup script should decide whether a user is to
use ccache or not. Anecdotally, I've heard from some in the dev team
that they are not using it themselves, so I don't think there is a good
basis to push it onto others.
That being said, we can of course still use ccache as part of the CI
builds nevertheless.
- if following line segment (fixed-wing position control) switch waypoint when in acceptance radius OR passed the second waypoint. this handles the case of being beyond the second waypoint but not within the acceptance radius without the need to fly back to the waypoint (e.g. after a loiter up to waypoint alt)
- sync navigator and fw pos ctrl waypoint acceptance altitude
- centralize logic for selecting a preferred calibration slot
- automatically use existing calibration slot if it exists, otherwise
find first available slot, with a preference for a requested index
- existing commander calibration methods rewrite all calibration slots
to match current sensor ordering
Before: in_ground_effect was always true with the default settings (LNDMC_ALT_GND =-1)
and when a distance sensor was present with valid data.
Now: default of LNDMC_ALT_GND is set to 2m by default, and if set to a negative value
then in_ground_effect is never set to true
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Since the same parameter is used to generate the trajectory and to
saturate the controller, there is no additional space for the output of
the position controller once it is filled with the feedforward, letting
the altitude grow uncontrolled.
The boot order is now:
1. The PX4 bootloader boots, and starts the camera.
2. The camera starts and sends the boot command to the PX4 bootloader.
3. PX4 starts.
This changes the way RC is handled for the Mantis:
- The RC values are re-written when arriving over MAVLink. They are
rescaled from 0..4095 to 1000..2000 and the channel bits added to
separate channels. This makes the downstream handling easier.
- Gimbal pitch is moved from Aux1 to Aux2 as that should be the default.
- Aux3 and Aux4 are used for the photo and video trigger.
- The speed button is used as the FLTMODE channel and set to switch
between POSCTL and ALTCTL.
This adds a check for the previous SYS_AUTOSTART id. If it is still the
old/previous SYS_AUTOSTART id, it will flash the new bootloader as well
as set the proper SYS_AUTOSTART id.
From what I can see the CONFIG_BOARDCTL_POWEROFF is not really used
anywhere, however, the BOARD_HAS_POWER_CONTROL is something that is set,
e.g. for the Mantis, to allow power off.
To play a power off tune, I needed to convert the file to C++, so that I
could use the uORB::Publication.
The current implementation starts playing the power off sound but then
stops it as soon as the button is released.
The problem is mostly that we only get an interrupt when the button is
pressed or released but we don't seem to be able to poll it, at least
not in the current state.
The limits might somewhat match the sensor, guessed based on the
original driver.
The quality is set so that spikes when sitting on the ground are not
used.
- this simplifies the reset by allowing a notch filter to reset as
needed
- improves cascade initialization, on reset each filter will reset
properly from the previous
- uavcan firmware server no longer shuts down when arming (nodes might restart in flight)
- always handle UAVCAN parameters with or without the FW server active
- remove legacy ESC enumeration in FW server
To avoid weird cases where the altitude is different enough and
the offtrack state flies to the target altitude instead of the closest
point on the track between the waypoints.
So instead of fuzzing each and every PR for 10minutes, we just fuzz
30mins every 24 hours, at 6am UTC which should be a time when US and
Europe might be least active.
This adds the env option PX4_FUZZ which runs the LLVM libFuzzer which
throws random bytes at mavlink_receiver using MAVLink messages over UDP.
The MAVLink messages that are being sent are valid, so the CRC is
calculated but the payload and msgid, etc. are generally garbage, unless
the fuzzing gets a msgid right by chance.
As I understand it, libFuzzer watches the test coverage and will try to
execute as much of the code as possible.
- sensors/vehicle_imu: reset learned cal on any calibration change
during parameter update
- sensors/vehicle_imu: cleanup logic estimated bias -> calibration offset
saving
- don't invalidate saved calibration (the point is to keep the last valid)
- remove old debug code, etc
- sensors/vehicle_imu: notify parameter changes if accel or gyro
calibration has changed
- lib/sensor_calibration: add calibrated() and calibration_index()
getters, keep Accelerometer/Gyroscope/Magnetometer in sync
This is an attempt to fix the test failure where PX4 detects an RC
timeout presumably because the tester process mavsdk_tests is stalled
and does not send RC control messages in time.
The imu and sensor_combined data should not be used when it has not been
updated yet, otherwise this triggers a memory sanitizer warning:
Conditional jump or move depends on uninitialised value(s)
at 0x2DA7AA: __sanitizer_cov_trace_const_cmp1 (in build/px4_sitl_default-clang/bin/px4)
by 0x3C4E79: EKF2::Run() (src/modules/ekf2/EKF2.cpp:401)
by 0x6EB881: px4::WorkQueue::Run() (platforms/common/px4_work_queue/WorkQueue.cpp:187)
by 0x6ECB9D: px4::WorkQueueRunner(void*) (platforms/common/px4_work_queue/WorkQueueManager.cpp:230)
by 0x4C07258: start_thread (in /usr/lib/libpthread-2.33.so)
by 0x4D415E2: clone (in /usr/lib/libc-2.33.so)
Conditional jump or move depends on uninitialised value(s)
at 0x3C4E7C: EKF2::Run() (src/modules/ekf2/EKF2.cpp:401)
by 0x6EB881: px4::WorkQueue::Run() (platforms/common/px4_work_queue/WorkQueue.cpp:187)
by 0x6ECB9D: px4::WorkQueueRunner(void*) (platforms/common/px4_work_queue/WorkQueueManager.cpp:230)
by 0x4C07258: start_thread (in /usr/lib/libpthread-2.33.so)
by 0x4D415E2: clone (in /usr/lib/libc-2.33.so)
- introuce slew rate limiting of airspeed setpoint (with slew rate of 1 m/s/s)
- some refactoring and clean up
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This prevents a memory sanitizer/valgrind warning:
Conditional jump or move depends on uninitialised value(s)
at 0x2DA536: __sanitizer_cov_trace_cmp4 (in build/px4_sitl_default-clang/bin/px4)
by 0x6590D8: FailureDetector::update(vehicle_status_s const&, vehicle_control_mode_s const&) (src/modules/commander/failure_detector/FailureDetector.cpp:76) by 0x3817DF: Commander::run() (src/modules/commander/Commander.cpp:2605)
by 0x38B10B: ModuleBase<Commander>::run_trampoline(int, char**) (platforms/common/include/px4_platform_common/module.h:180)
Using make tests in docker will fail, because the current basic image used by px4io/px4-dev-simulation-bionic is ubuntu18.04, the default version of cmake is 3.10, and the add_compile_definitions command is only available in cmake 3.12+(ubuntu 20.04).
The existing implementation had a flaw: when the buffer was getting full,
mavlink started to busy-loop, as the uart has data (poll returns immediately)
but no new data was read from the uart due to the buffer being full.
As rtps is running at lower prio, it never got the chance to read again,
making the problem even worse.
After 1s the timeout triggered and the buffer was cleared, so it recovered.
Instead of allowing for CPU spikes, we now immediately clear the buffer
(only as much as we have to), ensuring that new data is read from the uart.
In the tiltrotor case, beside an F_z thrust setpoint also a F_x setpoint must be passed
to the allocator as the matrix has non-zero thrust-x effectiveness when tilts are applied.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- allow effectiveness matrix to select control allocator method
(desaturation algorithm)
- add actuator_servos publication
- add support for multiple matrices (for vtol)
- add updateSetpoint callback method to actuator effectiveness to allow it
to manipulate the actuator setpoint after allocation
- handle motor stopping & reversal
- add control surfaces & tilt servos
- handle standard vtol + tiltrotor
- rename MC rotors params & class to be more generically usable
- fixes and enables ActuatorEffectivenessRotorsTest
Github constructs the workflow names from the
matrix configurations. Having latitude and longitude
in the fist columns makes these names rather cryptic.
- non-trivial perf counters (elapsed & interval) are relatively expensive
- if ESC and FFT notch filtering are enabled this reduces 6 updates (2 per axis) to 1
This enables flow control on CDCACM for the NuttX boards which fixes a
problem where HITL would stall.
The stall could happen if the hardware would be a bit too slow in
keeping up with the incoming messages. Often, this happened on arming
because the logger would take some time to log all parameters right at
the beginning.
The stall would then not recover due to NuttX bug where the rx interrupt
would not be restored correctly and instead only a slower watchdog would
release the next read. This watchdog takes 200ms which means it's hard
to impossible to get out of the situation without restarting sim and/or
PX4. For more information about the issue, see:
apache/incubator-nuttx#3633
As a workaround, until that bug is fixed, and because it makes sense
anyway, I propose to enable FLOWCONTROL for the serial via USB.
This enables the use case where the gimbal v2 protocol is used
between the ground station and the drone, and the gimbal v1 protocol is
used between the drone and the gimbal.
The existing implementation has about 100ms difference to a reference clock. With the changes this error less than 25us.
- Use sensor_gps messages with hrt timestamps as RTC reference and not the system realtime clock. The PPS interrupt can then be aligned with the GPS clock system.
- Keep fallback based on system RTC when no PPS pulse was captured
- camera_trigger module always publishes the camera_trigger msg (independent of the camera feedback)
- Use camera_trigger msg and set the feedback flag
- Subscribing modules determine if the message is relevant based on the feedback message
When using an FMU channel as PPS capture GPIO, the rtc_edge_time is now set as well. The delay between actual capture and callback is compensated with the elapsed time of the rtc clock.
- consider data clipped/saturated if it's INT16_MIN/INT16_MAX or within 1
- this accommodates rotated data (|INT16_MIN| = INT16_MAX + 1) and sensors that may re-use the lowest bit for other purposes (sync indicator, etc)
- Allocate and free the node name in uORBDeviceNode.
- Add protected build support by de-allocating the name with kmm_free, when
running in kernel side. strdup allocates from the kernel heap in NuttX kernel
space.
- Remove the CDev::unregister_driver_and_memory(), it is no longer used
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
In NuttX protected build there are separate work queues in kernel and user sides.
pthreads are only available in user side, so use tasks and kthreads for
memory protected builds.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- this was necessary to get the secondary ms5611 working reliably on a
particular CubeOrange
- the sensor is transferring very little data, so lowering the speed by
default everywhere is harmless
The FW Position controller sets the wp to be tracked during a
VTOL front transition, the coordinates sp set here weren't used.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- use NuttX gdb script for nxthreads and thread backtrace
- update jlink_gdb_backtrace and jlink_debug_gdb helper targets to use
NuttX gdb script
- Debug/PX4 fix "perf" divide by zero
- Debug/PX4 add "dmesg"
2021-12-05 19:18:56 -05:00
2769 changed files with 194545 additions and 58196 deletions
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sd_bench"'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sd_bench -v"'
@@ -803,28 +835,22 @@ void runTests() {
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sd_stress"'
// tests (stop modules first)
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander stop"'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mavlink stop-all"'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "navigator stop"'
sh './Tools/HIL/run_tests.py --device `find /dev/serial -name *usb-*`'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sensors stop"' // ignore irrelevant sensor timeouts during microbenchmarks
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "microbench all"'
// test rebooting multiple times
resetParameters()
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param set SYS_AUTOSTART 4001" || true'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param save"'
sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CBRK*; param show SYS*"' // check that CBRK_BUZZER and SYS_AUTOSTART haven't been lost
sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CBRK*; param show SYS*"' // check that CBRK_BUZZER and SYS_AUTOSTART haven't been lost
sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CBRK*; param show SYS*"' // check that CBRK_BUZZER and SYS_AUTOSTART haven't been lost
sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`'
sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CBRK*; param show SYS*"' // check that CBRK_BUZZER and SYS_AUTOSTART haven't been lost
about: See https://github.com/PX4/Devguide for documentation issues
about: See https://github.com/PX4/px4_user_guide for documentation issues
---
PX4 has dedicated repositories for developer documentation (https://github.com/PX4/Devguide) and user documentation (https://github.com/PX4/px4_user_guide).
## Attention! Please read the note below
**Please submit the documentation issue to the [User Guide](https://github.com/PX4/px4_user_guide) repository.**
Please use [PX4 Discuss](http://discuss.px4.io/) or [Slack](http://slack.px4.io/) to align on pull requests if necessary. You can then open draft pull requests to get early feedback.
**Describe problem solved by this pull request**
A clear and concise description of the problem this proposed change will solve.
## Describe problem solved by this pull request
A clear and concise description of the problem this proposed change will solve. Or, what it will improve.
E.g. For this use case I ran into...
**Describe your solution**
## Describe your solution
A clear and concise description of what you have implemented.
**Describe possible alternatives**
## Describe possible alternatives
A clear and concise description of alternative solutions or features you've considered.
**Test data / coverage**
## Test data / coverage
How was it tested? What cases were covered? Logs uploaded to https://review.px4.io/ and screenshots of the important plot parts.
The [developer guide](http://dev.px4.io/) explains how to set up the development environment on Mac OS, Linux or Windows. Please take note of our [coding style](https://dev.px4.io/master/en/contribute/code.html) when editing files.
The [developer guide](https://docs.px4.io/main/en/development/development.html) explains how to set up the development environment on Mac OS, Linux or Windows. Please take note of our [coding style](https://docs.px4.io/main/en/contribute/code.html) when editing files.
This repository holds the [PX4](http://px4.io) flight control solution for drones, with the main applications located in the [src/modules](https://github.com/PX4/PX4-Autopilot/tree/master/src/modules) directory. It also contains the PX4 Drone Middleware Platform, which provides drivers and middleware to run drones.
This repository holds the [PX4](http://px4.io) flight control solution for drones, with the main applications located in the [src/modules](https://github.com/PX4/PX4-Autopilot/tree/main/src/modules) directory. It also contains the PX4 Drone Middleware Platform, which provides drivers and middleware to run drones.
PX4 is highly portable, OS-independent and supports Linux, NuttX and MacOS out of the box.
* Official Website: http://px4.io (License: BSD 3-clause, [LICENSE](https://github.com/PX4/PX4-Autopilot/blob/master/LICENSE))
## Building a PX4 based drone, rover, boat or robot
The [PX4 User Guide](https://docs.px4.io/master/en/) explains how to assemble [supported vehicles](https://docs.px4.io/master/en/airframes/airframe_reference.html) and fly drones with PX4.
See the [forum and chat](https://docs.px4.io/master/en/#support) if you need help!
The [PX4 User Guide](https://docs.px4.io/main/en/) explains how to assemble [supported vehicles](https://docs.px4.io/main/en/airframes/airframe_reference.html) and fly drones with PX4.
See the [forum and chat](https://docs.px4.io/main/en/#getting-help) if you need help!
## Changing code and contributing
This [Developer Guide](https://docs.px4.io/master/en/development/development.html) is for software developers who want to modify the flight stack and middleware (e.g. to add new flight modes), hardware integrators who want to support new flight controller boards and peripherals, and anyone who wants to get PX4 working on a new (unsupported) airframe/vehicle.
This [Developer Guide](https://docs.px4.io/main/en/development/development.html) is for software developers who want to modify the flight stack and middleware (e.g. to add new flight modes), hardware integrators who want to support new flight controller boards and peripherals, and anyone who wants to get PX4 working on a new (unsupported) airframe/vehicle.
Developers should read the [Guide for Contributions](https://docs.px4.io/master/en/contribute/).
See the [forum and chat](https://dev.px4.io/master/en/#support) if you need help!
Developers should read the [Guide for Contributions](https://docs.px4.io/main/en/contribute/).
See the [forum and chat](https://docs.px4.io/main/en/#getting-help) if you need help!
### Weekly Dev Call
The PX4 Dev Team syncs up on a [weekly dev call](https://dev.px4.io/master/en/contribute/#dev_call).
The PX4 Dev Team syncs up on a [weekly dev call](https://docs.px4.io/main/en/contribute/).
> **Note** The dev call is open to all interested developers (not just the core dev team). This is a great opportunity to meet the team and contribute to the ongoing development of the platform. It includes a QA session for newcomers. All regular calls are listed in the [Dronecode calendar](https://www.dronecode.org/calendar/).
@@ -88,35 +88,43 @@ This repository contains code supporting Pixhawk standard boards (best supported
* FMUv6X and FMUv6U (STM32H7, 2021)
* Various vendors will provide FMUv6X and FMUv6U based designs Q3/2021
* [Raspberry PI with Navio 2](https://docs.px4.io/main/en/flight_controller/raspberry_pi_navio2.html)
Additional information about supported hardware can be found in [PX4 user Guide > Autopilot Hardware](https://docs.px4.io/master/en/flight_controller/).
Additional information about supported hardware can be found in [PX4 user Guide > Autopilot Hardware](https://docs.px4.io/main/en/flight_controller/).
## Project Roadmap
A high level project roadmap is available [here](https://github.com/orgs/PX4/projects/25).
## Project Governance
The PX4 Autopilot project including all of its trademarks is hosted under [Dronecode](https://www.dronecode.org/), part of the Linux Foundation.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Daniel Agar