make demo work with pca.

ucan pwm enablement.
S32K1 fixes.
2026-05-23 19:07:35 +08:00 · 2022-06-01 18:22:23 -04:00 · 2022-06-01 13:36:40 -04:00 · 2022-05-31 16:56:49 -04:00 · 2022-05-26 10:52:08 -04:00 · 2022-05-25 17:44:54 -04:00
1390 changed files with 103033 additions and 22877 deletions
@@ -28,7 +28,7 @@ pipeline {
          ]

          def base_builds = [
-            target: ["px4_sitl_rtps"],
+            target: ["px4_sitl_default"],
            image: docker_images.base,
            archive: false
          ]
@@ -52,25 +52,29 @@ pipeline {
                     "cuav_x7pro_default",
                     "cubepilot_cubeorange_default",
                     "cubepilot_cubeyellow_default",
+                     "diatone_mamba-f405-mk2_default",
                     "freefly_can-rtk-gps_canbootloader",
                     "freefly_can-rtk-gps_default",
                     "holybro_can-gps-v1_canbootloader",
                     "holybro_can-gps-v1_default",
                     "holybro_durandal-v1_default",
                     "holybro_kakutef7_default",
+                     "holybro_kakuteh7_default",
                     "holybro_pix32v5_default",
-                     "matek_h743-slim",
                     "matek_gnss-m9n-f4_canbootloader",
                     "matek_gnss-m9n-f4_default",
+                     "matek_h743-mini_default",
+                     "matek_h743-slim_default",
+                     "matek_h743_default",
                     "modalai_fc-v1_default",
                     "modalai_fc-v1_rtps",
                     "modalai_fc-v2_default",
                     "mro_ctrl-zero-f7_default",
                     "mro_ctrl-zero-f7-oem_default",
-                     "mro_ctrl-zero-h7_default",
-                     "mro_ctrl-zero-h7_rtps",
                     "mro_ctrl-zero-h7-oem_default",
                     "mro_ctrl-zero-h7-oem_rtps",
+                     "mro_ctrl-zero-h7_default",
+                     "mro_ctrl-zero-h7_rtps",
                     "mro_pixracerpro_default",
                     "mro_pixracerpro_rtps",
                     "mro_x21-777_default",
@@ -85,24 +89,28 @@ pipeline {
                     "nxp_ucans32k146_canbootloader",
                     "nxp_ucans32k146_default",
                     "omnibus_f4sd_default",
-                     "raspberrypi_pico_default",
                     "px4_fmu-v2_default",
                     "px4_fmu-v2_fixedwing",
+                     "px4_fmu-v2_lto",
                     "px4_fmu-v2_multicopter",
                     "px4_fmu-v2_rover",
                     "px4_fmu-v3_default",
                     "px4_fmu-v4_default",
                     "px4_fmu-v4pro_default",
+                     "px4_fmu-v5_cyphal",
                     "px4_fmu-v5_debug",
                     "px4_fmu-v5_default",
+                     "px4_fmu-v5_lto",
                     "px4_fmu-v5_rtps",
                     "px4_fmu-v5_stackcheck",
                     "px4_fmu-v5_uavcanv0periph",
-                     "px4_fmu-v5_uavcanv1",
                     "px4_fmu-v5x_default",
+                     "px4_fmu-v6c_default",
                     "px4_fmu-v6u_default",
                     "px4_fmu-v6x_default",
                     "px4_io-v2_default",
+                     "raspberrypi_pico_default",
+                     "sky-drones_smartap-airlink_default",
                     "spracing_h7extreme_default",
                     "uvify_core_default"
            ],
@@ -73,10 +73,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/cubepilot_cubeorange_test/cubepilot_cubeorange_test.elf || true'
                }
              }
@@ -145,10 +143,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/cuav_x7pro_test/cuav_x7pro_test.elf || true'
                }
              }
@@ -217,10 +213,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v3_test/px4_fmu-v3_test.elf || true'
                }
              }
@@ -288,10 +282,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v4_test/px4_fmu-v4_test.elf || true'
                }
              }
@@ -360,10 +352,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v4pro_test/px4_fmu-v4pro_test.elf || true'
                }
              }
@@ -452,10 +442,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_debug/px4_fmu-v5_debug.elf || true'
                }
              }
@@ -536,10 +524,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_stackcheck/px4_fmu-v5_stackcheck.elf || true'
                }
              }
@@ -608,10 +594,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_test/px4_fmu-v5_test.elf || true'
                }
              }
@@ -680,10 +664,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/nxp_fmuk66-v3_test/nxp_fmuk66-v3_test.elf || true'
                }
              }
@@ -723,18 +705,21 @@ void quickCalibrate() {

  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "gyro_calibration status || true"'

-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate accel quick"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate accel quick; sleep 1"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CAL_ACC*"'

-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate gyro"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate gyro; sleep 2"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CAL_GYRO*"'

-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate level"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate level; sleep 2"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show SENS*"'

-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate mag quick"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate mag quick; sleep 1"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CAL_MAG*"'

+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "commander calibrate baro; sleep 5"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CAL_BARO*"'
+
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show CAL_*"' // parameters after
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sensors status"'
 }
@@ -793,7 +778,7 @@ void checkStatus() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "top once"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uavcan status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb status" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "ver all"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "work_queue status"'
  // stop logger
@@ -809,7 +794,7 @@ void resetParameters() {
 void runTests() {

  // test loading a range of airframes
-  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 1000 1001 2100 3000 4001 4018 6001 8001 10016'
+  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 2100 3000 4001 6001 8001 10016'

  resetParameters()

@@ -862,7 +847,7 @@ void runTests() {
 void printTopics() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "ls /obj"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb status"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a" || true'

  // these are for casually inspecting the system, output failure doesn't matter
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener actuator_armed" || true'
@@ -879,12 +864,15 @@ void printTopics() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener cpuload" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener distance_sensor" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener ekf2_timestamps" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener ekf_gps_drift" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener esc_status" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_fake_pos" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_gnss_pos" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_aid_src_gnss_vel" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_attitude" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_baro_bias" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_event_flags" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_global_position" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_gps_status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovation_test_ratios" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovation_variances" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_innovations" || true'
@@ -1,32 +1,34 @@
 ---
-name: Bug report
+name: 🐛 Bug report
 about: Create a report to help us improve
+labels: bug-report

 ---

-**Describe the bug**
+## Describe the bug
 A clear and concise description of the bug.

-**To Reproduce**
+## To Reproduce
 Steps to reproduce the behavior:
 1. Drone switched on '...'
 2. Uploaded mission '....' (attach QGC mission file)
 3. Took off '....'
 4. See error

-**Expected behavior**
+## Expected behavior
 A clear and concise description of what you expected to happen.

-**Log Files and Screenshots**
+## Log Files and Screenshots
 *Always* provide a link to the flight log file:
 - Download the flight log file from the vehicle ([tutorial](https://docs.px4.io/master/en/getting_started/flight_reporting.html)).
- Share the link to a log showing the problem on [PX4 Flight Review](http://logs.px4.io/).
+- Upload the log to the [PX4 Flight Review](http://logs.px4.io/)
+- Share the link to the log (Copy and paste the URL of the log)

 Add screenshots to help explain your problem.

-**Drone (please complete the following information):**
+## Drone (please complete the following information):
 - Describe the type of drone.
 - Photo of the IMU / autopilot setup if possible.

-**Additional context**
+## Additional context
 Add any other context about the problem here.
@@ -1,19 +1,20 @@
 ---
 name: 🚀 Feature Request
 about: Suggest an idea for this project
+labels: feature-request

 ---

 For general questions please use [PX4 Discuss](http://discuss.px4.io/) or Slack (you can find an invite link on this project README).

-**Describe problem solved by the proposed feature**
+## Describe problem solved by the proposed feature
 A clear and concise description of the problem, if any, this feature will solve. E.g. I'm always frustrated when ...

-**Describe your preferred solution**
+## Describe your preferred solution
 A clear and concise description of what you want to happen.

-**Describe possible alternatives**
+## Describe possible alternatives
 A clear and concise description of alternative solutions or features you've considered.

-**Additional context**
+## Additional context
 Add any other context or screenshots for the feature request here.
@@ -1,10 +1,13 @@
 ---
 name: ⛔ Support Question
-about: See [PX4 Discuss](http://discuss.px4.io/) for questions about using PX4.
+about: See http://discuss.px4.io/ for questions about using PX4.

 ---

-We use GitHub issues only to discuss PX4 bugs and new features. For
-questions about using PX4 or related components, please use [PX4 Discuss](http://discuss.px4.io/).
+## Attention! Please read the note below
+
+We use GitHub issues only to discuss PX4 bugs and new features.
+
+**For questions about using PX4 or related components, please use [PX4 Discuss](http://discuss.px4.io/).**

 Thanks!
@@ -1,9 +1,11 @@
 ---
 name: ⛔ Documentation Issue
-about: See https://github.com/PX4/Devguide for documentation issues
+about: See https://github.com/PX4/px4_user_guide for documentation issues

 ---

-PX4 has dedicated repositories for developer documentation (https://github.com/PX4/Devguide) and user documentation (https://github.com/PX4/px4_user_guide).
+## Attention! Please read the note below
+
+**Please submit the documentation issue to the [User Guide](https://github.com/PX4/px4_user_guide) repository.**

 Thanks!
@@ -1,17 +1,17 @@
 Please use [PX4 Discuss](http://discuss.px4.io/) or [Slack](http://slack.px4.io/) to align on pull requests if necessary. You can then open draft pull requests to get early feedback.

-**Describe problem solved by this pull request**
-A clear and concise description of the problem this proposed change will solve.
+## Describe problem solved by this pull request
+A clear and concise description of the problem this proposed change will solve. Or, what it will improve.
 E.g. For this use case I ran into...

-**Describe your solution**
+## Describe your solution
 A clear and concise description of what you have implemented.

-**Describe possible alternatives**
+## Describe possible alternatives
 A clear and concise description of alternative solutions or features you've considered.

-**Test data / coverage**
+## Test data / coverage
 How was it tested? What cases were covered? Logs uploaded to https://review.px4.io/ and screenshots of the important plot parts.

-**Additional context**
+## Additional context
 Add any other related context or media.
@@ -20,6 +20,7 @@ jobs:
          ark_can-flow,
          ark_can-gps,
          ark_can-rtk-gps,
+          ark_cannode,
          atl_mantis-edu,
          av_x-v1,
          bitcraze_crazyflie,
@@ -29,14 +30,17 @@ jobs:
          cuav_x7pro,
          cubepilot_cubeorange,
          cubepilot_cubeyellow,
+          diatone_mamba-f405-mk2,
          freefly_can-rtk-gps,
          holybro_can-gps-v1,
          holybro_durandal-v1,
          holybro_kakutef7,
          holybro_kakuteh7,
          holybro_pix32v5,
-          matek_h743-slim,
          matek_gnss-m9n-f4,
+          matek_h743,
+          matek_h743-mini,
+          matek_h743-slim,
          modalai_fc-v1,
          modalai_fc-v2,
          mro_ctrl-zero-f7,
@@ -51,15 +55,17 @@ jobs:
          nxp_fmurt1062-v1,
          nxp_ucans32k146,
          omnibus_f4sd,
-          raspberrypi_pico,
          px4_fmu-v2,
          px4_fmu-v3,
          px4_fmu-v4,
          px4_fmu-v4pro,
          px4_fmu-v5,
          px4_fmu-v5x,
+          px4_fmu-v6c,
          px4_fmu-v6u,
          px4_fmu-v6x,
+          raspberrypi_pico,
+          sky-drones_smartap-airlink,
          spracing_h7extreme,
          uvify_core
          ]
@@ -29,9 +29,9 @@ jobs:
        token: ${{ secrets.ACCESS_TOKEN }}

    - name: Download MAVSDK
-      run: wget "https://github.com/mavlink/MAVSDK/releases/download/v$(cat test/mavsdk_tests/MAVSDK_VERSION)/mavsdk_$(cat test/mavsdk_tests/MAVSDK_VERSION)_ubuntu20.04_amd64.deb"
+      run: wget "https://github.com/mavlink/MAVSDK/releases/download/v$(cat test/mavsdk_tests/MAVSDK_VERSION)/libmavsdk-dev_$(cat test/mavsdk_tests/MAVSDK_VERSION)_ubuntu20.04_amd64.deb"
    - name: Install MAVSDK
-      run: dpkg -i "mavsdk_$(cat test/mavsdk_tests/MAVSDK_VERSION)_ubuntu20.04_amd64.deb"
+      run: dpkg -i "libmavsdk-dev_$(cat test/mavsdk_tests/MAVSDK_VERSION)_ubuntu20.04_amd64.deb"

    - name: Prepare ccache timestamp
      id: ccache_cache_timestamp
@@ -36,14 +36,14 @@
 [submodule "Tools/jsbsim_bridge"]
 	path = Tools/jsbsim_bridge
 	url = https://github.com/PX4/px4-jsbsim-bridge.git
-[submodule "src/drivers/uavcan_v1/libcanard"]
-	path = src/drivers/uavcan_v1/libcanard
-	url = https://github.com/UAVCAN/libcanard.git
-[submodule "src/drivers/uavcan_v1/public_regulated_data_types"]
-	path = src/drivers/uavcan_v1/public_regulated_data_types
-	url = https://github.com/UAVCAN/public_regulated_data_types.git
-[submodule "src/drivers/uavcan_v1/legacy_data_types"]
-	path = src/drivers/uavcan_v1/legacy_data_types
+[submodule "src/drivers/cyphal/libcanard"]
+	path = src/drivers/cyphal/libcanard
+	url = https://github.com/opencyphal/libcanard.git
+[submodule "src/drivers/cyphal/public_regulated_data_types"]
+	path = src/drivers/cyphal/public_regulated_data_types
+	url = https://github.com/opencyphal/public_regulated_data_types.git
+[submodule "src/drivers/cyphal/legacy_data_types"]
+	path = src/drivers/cyphal/legacy_data_types
 	url = https://github.com/PX4/public_regulated_data_types.git
 	branch = legacy
 [submodule "src/lib/crypto/monocypher"]
@@ -64,3 +64,6 @@
 	path = src/lib/crypto/libtommath
 	url = https://github.com/PX4/libtommath.git
 	branch = px4
+[submodule "src/modules/microdds_client/Micro-XRCE-DDS-Client"]
+	path = src/modules/microdds_client/Micro-XRCE-DDS-Client
+	url = https://github.com/eProsima/Micro-XRCE-DDS-Client.git
@@ -9,3 +9,5 @@ launch.json
 ipch/

 browse.vc.db*
+
+*.log
@@ -121,6 +121,16 @@ CONFIG:
      buildType: MinSizeRel
      settings:
        CONFIG: ark_can-rtk-gps_canbootloader
+    ark_cannode_default:
+      short: ark_cannode_default
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_cannode_default
+    ark_cannode_canbootloader:
+      short: ark_cannode_canbootloader
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_cannode_canbootloader
    atl_mantis-edu_default:
      short: atl_mantis-edu
      buildType: MinSizeRel
@@ -99,7 +99,7 @@
 #
 #=============================================================================

-cmake_minimum_required(VERSION 3.2 FATAL_ERROR)
+cmake_minimum_required(VERSION 3.9 FATAL_ERROR)

 set(PX4_SOURCE_DIR "${CMAKE_CURRENT_SOURCE_DIR}" CACHE FILEPATH "PX4 source directory" FORCE)
 set(PX4_BINARY_DIR "${CMAKE_CURRENT_BINARY_DIR}" CACHE FILEPATH "PX4 binary directory" FORCE)
@@ -234,6 +234,14 @@ message(STATUS "cmake build type: ${CMAKE_BUILD_TYPE}")
 #
 project(px4 CXX C ASM)

+# Check if LTO option and check if toolchain supports it
+if(LTO)
+    include(CheckIPOSupported)
+    check_ipo_supported()
+    message(AUTHOR_WARNING "LTO enabled: LTO is highly experimental and should not be used in production")
+    set(CMAKE_INTERPROCEDURAL_OPTIMIZATION TRUE)
+endif()
+
 set(package-contact "px4users@googlegroups.com")

 set(CMAKE_CXX_STANDARD 14)
@@ -412,6 +420,7 @@ endif()
 # subdirectories
 #
 add_library(parameters_interface INTERFACE)
+add_library(kernel_parameters_interface INTERFACE)

 include(px4_add_library)
 add_subdirectory(src/lib EXCLUDE_FROM_ALL)
@@ -434,7 +443,13 @@ add_subdirectory(src/lib/metadata EXCLUDE_FROM_ALL)

 # must be the last module before firmware
 add_subdirectory(src/lib/parameters EXCLUDE_FROM_ALL)
+
+if(${PX4_PLATFORM} STREQUAL "nuttx" AND NOT CONFIG_BUILD_FLAT)
+target_link_libraries(parameters_interface INTERFACE usr_parameters)
+target_link_libraries(kernel_parameters_interface INTERFACE parameters)
+else()
 target_link_libraries(parameters_interface INTERFACE parameters)
+endif()

 # firmware added last to generate the builtin for included modules
 add_subdirectory(platforms/${PX4_PLATFORM})
@@ -51,6 +51,13 @@ menu "Toolchain"
        string "Architecture"
        default ""

+    config BOARD_LTO
+        bool "(EXPERIMENTAL) Link Time Optimization (LTO)"
+        default n
+        help
+            Enables LTO flag in linker
+            Note: Highly EXPERIMENTAL, furthermore make sure you're using a modern compiler GCC 9 or later
+
    config BOARD_FULL_OPTIMIZATION
        bool "Full optmization (O3)"
        default n
@@ -325,12 +325,13 @@ px4io_update: px4_io-v2_default cubepilot_io-v2_default
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v5/extras/px4_io-v2_default.bin
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v5x/extras/px4_io-v2_default.bin
 	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v6x/extras/px4_io-v2_default.bin
+	cp build/px4_io-v2_default/px4_io-v2_default.bin boards/px4/fmu-v6c/extras/px4_io-v2_default.bin
 	# cubepilot_io-v2_default
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeorange/extras/cubepilot_io-v2_default.bin
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeyellow/extras/cubepilot_io-v2_default.bin
 	git status

-bootloaders_update: cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
+bootloaders_update: cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader matek_h743_bootloader matek_h743-mini_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
 	git status

 .PHONY: coverity_scan
@@ -32,3 +32,4 @@
 ############################################################################

 add_subdirectory(init.d)
+add_subdirectory(mixers)
@@ -33,4 +33,5 @@

 px4_add_romfs_files(
 	rcS
+	rc.output_defaults
 )
@@ -0,0 +1,32 @@
+#!/bin/sh
+#
+# UGV default parameters.
+#
+# NOTE: Script variables are declared/initialized/unset in the rcS script.
+#
+
+#
+# Enable servo output on pins 3 and 4 (steering and thrust)
+# but also include 1+2 as they form together one output group
+# and need to be set together.
+#
+set PWM_OUT 12
+
+#
+# PWM Hz - 50 Hz is the normal rate in RC cars, higher rates
+# may damage analog servos.
+#
+set PWM_MAIN_RATE 50
+
+#
+# This is the gimbal pass mixer.
+#
+set MIXER_AUX pass
+set PWM_AUX_OUT 12
+
+param set-default PWM_MAIN_DISARM 1500
+param set-default PWM_MAIN_MAX 2000
+param set-default PWM_MAIN_MIN 1000
+
+# Set mixer
+set MIXER IO_pass_ucan
@@ -65,8 +65,8 @@ unset BOARD_RC_DEFAULTS
 #
 # Start system state indicator.
 #
-rgbled start -X -q
-rgbled_ncp5623c start -X -q
+#rgbled start -X -q
+#rgbled_ncp5623c start -X -q

 #
 # board sensors: rc.sensors
@@ -86,10 +86,10 @@ unset BOARD_RC_SENSORS
 . ${R}etc/init.d/rc.serial

 # Check for flow sensor
-if param compare SENS_EN_PX4FLOW 1
-then
-	px4flow start -X
-fi
+#if param compare SENS_EN_PX4FLOW 1
+#then
+#	px4flow start -X &
+#fi

-uavcannode start
+#uavcannode start
 unset R
@@ -1,6 +1,6 @@
 ############################################################################
 #
-#   Copyright (c) 2019 PX4 Development Team. All rights reserved.
+#   Copyright (c) 2018 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -31,4 +31,6 @@
 #
 ############################################################################

-px4_add_library(drivers_barometer PX4Barometer.cpp)
+px4_add_romfs_files(
+	IO_pass_ucan.main.mix
+)
@@ -0,0 +1,12 @@
+Passthrough mixer for PX4IO
+============================
+
+This file defines passthrough mixers suitable for testing.
+
+Channel group 0, channels 0-7 are passed directly through to the outputs.
+
+M: 1
+S: 0 0  10000  10000      0 -10000  10000
+
+M: 1
+S: 0 1  10000  10000      0 -10000  10000
@@ -10,6 +10,7 @@
 # enable fusion of landing target velocity
 param set-default LTEST_MODE 1
 param set-default PLD_HACC_RAD 0.1
+param set-default RTL_PLD_MD 2

 # Start up Landing Target Estimator module
 landing_target_estimator start
@@ -8,8 +8,5 @@
 # disable circuit breaker for airspeed sensor
 param set-default CBRK_AIRSPD_CHK 162128

-set MAV_TYPE 12
-param set MAV_TYPE ${MAV_TYPE}
-
 set MIXER_FILE etc/mixers-sitl/uuv_x_sitl.main.mix
 set MIXER custom
@@ -8,8 +8,5 @@
 # disable circuit breaker for airspeed sensor
 param set-default CBRK_AIRSPD_CHK 162128

-set MAV_TYPE 12
-param set MAV_TYPE ${MAV_TYPE}
-
 set MIXER_FILE etc/mixers-sitl/uuv_x_sitl.main.mix
 set MIXER custom
@@ -67,4 +67,3 @@ param set-default PWM_MAIN_FUNC7 107
 param set-default PWM_MAIN_FUNC8 108

 set MIXER skip
-
@@ -25,6 +25,8 @@ param set-default FW_P_LIM_MIN -15
 param set-default FW_RR_FF 0.1
 param set-default FW_RR_P 0.3

+param set-default FW_SPOILERS_LND 0.4
+
 param set-default FW_THR_MAX 0.6
 param set-default FW_THR_MIN 0.05
 param set-default FW_THR_CRUISE 0.25
@@ -44,6 +44,8 @@ param set-default MIS_TAKEOFF_ALT 30
 param set-default NAV_ACC_RAD 15
 param set-default NAV_DLL_ACT 2

+param set-default FW_USE_NPFG 1
+
 param set-default RWTO_TKOFF 1

 set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
@@ -7,10 +7,15 @@

 . ${R}etc/init.d/rc.vtol_defaults

+# TODO: Enable motor failure detection when the
+# VTOL no longer reports 0A for all ESCs in SITL
+param set-default FD_ACT_EN 0
+param set-default FD_ACT_MOT_TOUT 500
+
 # param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 2

-param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR_COUNT 5
 param set-default CA_ROTOR0_PX 0.1515
 param set-default CA_ROTOR0_PY 0.245
 param set-default CA_ROTOR0_KM 0.05
@@ -23,6 +28,9 @@ param set-default CA_ROTOR2_KM -0.05
 param set-default CA_ROTOR3_PX -0.1515
 param set-default CA_ROTOR3_PY 0.1875
 param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2

 param set-default CA_SV_CS_COUNT 3
 param set-default CA_SV_CS0_TYPE 1
@@ -68,7 +76,6 @@ param set-default MPC_XY_VEL_I_ACC 4
 param set-default MPC_XY_VEL_D_ACC 0.1

 param set-default NAV_ACC_RAD 5
-param set-default NAV_LOITER_RAD 80

 param set-default VT_FWD_THRUST_EN 4
 param set-default VT_F_TRANS_THR 0.75
@@ -77,7 +84,5 @@ param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_B_TRANS_DUR 8
 param set-default VT_TYPE 2

-set MAV_TYPE 22
-
 set MIXER_FILE etc/mixers-sitl/standard_vtol_sitl.main.mix
 set MIXER custom
@@ -7,6 +7,8 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 20
+
 # param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 4

@@ -68,7 +70,6 @@ param set-default MPC_XY_VEL_I_ACC 4
 param set-default MPC_XY_VEL_D_ACC 0.1

 param set-default NAV_ACC_RAD 5
-param set-default NAV_LOITER_RAD 80

 param set-default VT_FW_DIFTHR_EN 1
 param set-default VT_FW_DIFTHR_SC 0.5
@@ -78,7 +79,5 @@ param set-default VT_TYPE 0

 param set-default WV_EN 0

-set MAV_TYPE 20
-
 set MIXER_FILE etc/mixers-sitl/quad_x_vtol.main.mix
 set MIXER custom
@@ -7,7 +7,9 @@

 . ${R}etc/init.d/rc.vtol_defaults

-# param set-default SYS_CTRL_ALLOC 1
+param set-default MAV_TYPE 21
+
+param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 3

 param set-default CA_ROTOR_COUNT 4
@@ -25,9 +27,7 @@ param set-default CA_ROTOR3_PY 0.1875
 param set-default CA_ROTOR3_KM -0.05

 param set-default CA_ROTOR0_TILT 1
-param set-default CA_ROTOR1_TILT 2
 param set-default CA_ROTOR2_TILT 3
-param set-default CA_ROTOR3_TILT 4
 param set-default CA_SV_CS0_TRQ_R -0.5
 param set-default CA_SV_CS0_TYPE 1
 param set-default CA_SV_CS1_TRQ_R 0.5
@@ -80,7 +80,6 @@ param set-default MPC_XY_VEL_I_ACC 4
 param set-default MPC_XY_VEL_D_ACC 0.1

 param set-default NAV_ACC_RAD 5
-param set-default NAV_LOITER_RAD 80

 param set-default VT_B_TRANS_DUR 8
 param set-default VT_FWD_THRUST_EN 4
@@ -88,7 +87,5 @@ param set-default VT_MOT_ID 1234
 param set-default VT_TILT_TRANS 0.6
 param set-default VT_TYPE 1

-set MAV_TYPE 21
-
 set MIXER_FILE etc/mixers-sitl/tiltrotor_sitl.main.mix
 set MIXER custom
@@ -38,7 +38,6 @@ param set-default MPC_XY_VEL_I_ACC 4
 param set-default MPC_XY_VEL_D_ACC 0.1

 param set-default NAV_ACC_RAD 5
-param set-default NAV_LOITER_RAD 80

 param set-default VT_FWD_THRUST_EN 4
 param set-default VT_F_TRANS_THR 0.75
@@ -51,7 +50,5 @@ param set-default RC_MAP_AUX1 8
 param set-default RC_MAP_AUX2 9
 param set-default RC_MAP_AUX3 10

-set MAV_TYPE 22
-
 set MIXER_FILE etc/mixers-sitl/standard_vtol_sitl.main.mix
 set MIXER custom
@@ -37,6 +37,4 @@ param set-default PWM_MAIN_FUNC2 201
 param set-default PWM_MAIN_FUNC6 101
 param set-default PWM_MAIN_FUNC7 101

-set MAV_TYPE 10
-
 set MIXER_FILE skip
@@ -37,6 +37,4 @@ param set-default PWM_MAIN_FUNC2 101
 param set-default PWM_MAIN_FUNC6 102
 param set-default PWM_MAIN_FUNC7 102

-set MAV_TYPE 10
-
 set MIXER_FILE skip
@@ -10,6 +10,8 @@

 . ${R}etc/init.d/rc.rover_defaults

+param set-default MAV_TYPE 10
+
 param set-default GND_L1_DIST 5
 param set-default GND_SP_CTRL_MODE 1
 param set-default GND_SPEED_D 3
@@ -33,6 +35,4 @@ param set-default CBRK_AIRSPD_CHK 162128
 param set-default GND_MAX_ANG 0.6
 param set-default GND_WHEEL_BASE 3.0

-set MAV_TYPE 10
-
 set MIXER_FILE etc/mixers-sitl/rover_ackermann_sitl.main.mix
@@ -47,6 +47,4 @@ param set-default CA_R_REV 3
 param set-default PWM_MAIN_FUNC1 101
 param set-default PWM_MAIN_FUNC2 102

-set MAV_TYPE 11
-
 set MIXER skip
@@ -9,6 +9,8 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default MAV_TYPE 13
+
 param set-default MC_PITCHRATE_P 0.1
 param set-default MC_PITCHRATE_I 0.05
 param set-default MC_PITCH_P 6.0
@@ -24,6 +26,4 @@ param set-default TRIG_MODE 4
 param set-default MNT_MODE_IN 4
 param set-default MNT_DO_STAB 2

-set MAV_TYPE 13
-
 set MIXER hexa_x
@@ -7,6 +7,8 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default MAV_TYPE 13
+
 param set-default MC_PITCHRATE_P 0.0800
 param set-default MC_PITCHRATE_I 0.0400
 param set-default MC_PITCHRATE_D 0.0010
@@ -26,6 +28,4 @@ param set-default MNT_MODE_IN 4
 param set-default MNT_MODE_OUT 2
 param set-default MAV_PROTO_VER 2

-set MAV_TYPE 13
-
 set MIXER hexa_x
@@ -7,6 +7,8 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default MAV_TYPE 13
+
 param set-default SYS_CTRL_ALLOC 1

 param set-default MC_PITCHRATE_P 0.0800
@@ -58,7 +60,5 @@ param set-default PWM_MAIN_FUNC4 104
 param set-default PWM_MAIN_FUNC5 105
 param set-default PWM_MAIN_FUNC6 106

-set MAV_TYPE 13
-
 set MIXER skip
 set MIXER_AUX none
@@ -1,6 +1,4 @@

-mixer append /dev/pwm_output0 etc/mixers/mount_legs.aux.mix
-
 mavlink start -x -u 14558 -r 4000 -f -m onboard -o 14530 -p

 # shellcheck disable=SC2154
@@ -24,7 +24,6 @@ fi

 # initialize script variables
 set IO_PRESENT                  no
-set MAV_TYPE                    none
 set MIXER                       none
 set MIXER_AUX                   none
 set MIXER_FILE                  none
@@ -96,10 +95,9 @@ fi

 if param compare SYS_AUTOCONFIG 1
 then
+	# Reset params except Airframe, RC calibration, sensor calibration, flight modes, total flight time, and next flight UUID.
+	param reset_all SYS_AUTOSTART RC* CAL_* COM_FLTMODE* LND_FLIGHT* TC_* COM_FLIGHT*
 	set AUTOCNF yes
-
-	# Wipe out params except RC*, flight modes, total flight time, accel cal, gyro cal, next flight UUID
-	param reset_all SYS_AUTO* RC* COM_FLTMODE* LND_FLIGHT* TC_* CAL_ACC* CAL_GYRO* COM_FLIGHT*
 fi

 # multi-instance setup
@@ -197,14 +195,6 @@ fi

 . "$autostart_file"

-#
-# If autoconfig parameter was set, reset it and save parameters.
-#
-if [ $AUTOCNF = yes ]
-then
-	param set SYS_AUTOCONFIG 0
-fi
-
 # Simulator IMU data provided at 250 Hz
 param set IMU_INTEG_RATE 250

@@ -224,6 +214,13 @@ rc_update start
 manual_control start
 sensors start
 commander start
+
+# Configure vehicle type specific parameters.
+# Note: rc.vehicle_setup is the entry point for rc.interface,
+#       rc.fw_apps, rc.mc_apps, rc.rover_apps, and rc.vtol_apps.
+#
+. ${R}etc/init.d/rc.vehicle_setup
+
 navigator start

 # Try to start the micrortps_client with UDP transport if module exists
@@ -234,7 +231,7 @@ fi

 if param greater -s MNT_MODE_IN -1
 then
-	vmount start
+	gimbal start
 fi

 if param greater -s TRIG_MODE 0
@@ -253,12 +250,6 @@ then
 	gyro_calibration start
 fi

-# Configure vehicle type specific parameters.
-# Note: rc.vehicle_setup is the entry point for rc.interface,
-#       rc.fw_apps, rc.mc_apps, rc.rover_apps, and rc.vtol_apps.
-#
-. ${R}etc/init.d/rc.vehicle_setup
-
 #user defined mavlink streams for instances can be in PATH
 . px4-rc.mavlink

@@ -55,4 +55,5 @@ px4_add_romfs_files(
 	rc.vehicle_setup
 	rc.vtol_apps
 	rc.vtol_defaults
+	rc.output_defaults
 )
@@ -39,8 +39,30 @@ param set-default FW_RR_P 0.3

 param set-default RWTO_TKOFF 1

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R 0.5
+param set-default CA_SV_CS0_TYPE 2
+param set-default CA_SV_CS1_TRQ_P 1.0
+param set-default CA_SV_CS1_TYPE 3
+param set-default CA_SV_CS2_TRQ_Y 1.0
+param set-default CA_SV_CS2_TYPE 4
+param set-default CA_SV_CS3_TYPE 10
+
+param set-default HIL_ACT_REV 2
+param set-default HIL_ACT_FUNC1 201
+param set-default HIL_ACT_FUNC2 202
+param set-default HIL_ACT_FUNC3 203
+param set-default HIL_ACT_FUNC4 101
+param set-default HIL_ACT_FUNC5 204
+param set-default HIL_ACT_FUNC6 400
+
 param set SYS_HITL 1

+param set UAVCAN_ENABLE 0
+
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -1,39 +0,0 @@
-#!/bin/sh
-#
-# @name Steadidrone QU4D
-#
-# @type Quadrotor Wide
-# @class Copter
-#
-# @output MAIN1 motor 1
-# @output MAIN2 motor 2
-# @output MAIN3 motor 3
-# @output MAIN4 motor 4
-# @output MAIN5 feed-through of RC AUX1 channel
-# @output MAIN6 feed-through of RC AUX2 channel
-#
-# @output AUX1 feed-through of RC AUX1 channel
-# @output AUX2 feed-through of RC AUX2 channel
-# @output AUX3 feed-through of RC AUX3 channel
-# @output AUX4 feed-through of RC FLAPS channel
-#
-# @maintainer Lorenz Meier <lorenz@px4.io>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default BAT1_N_CELLS 4
-
-param set-default MC_ROLL_P 7
-param set-default MC_ROLLRATE_P 0.13
-param set-default MC_ROLLRATE_I 0.05
-param set-default MC_ROLLRATE_D 0.004
-param set-default MC_PITCH_P 7
-param set-default MC_PITCHRATE_P 0.19
-param set-default MC_PITCHRATE_I 0.05
-param set-default MC_PITCHRATE_D 0.004
-param set-default MC_YAW_P 4
-set MIXER quad_w
@@ -15,6 +15,25 @@ set MIXER quad_x

 param set SYS_HITL 1

+param set UAVCAN_ENABLE 0
+
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -49,7 +49,6 @@ param set-default MPC_Z_VEL_MAX_DN 1.5

 param set-default NAV_ACC_RAD 5
 param set-default NAV_DLL_ACT 2
-param set-default NAV_LOITER_RAD 80

 param set-default RTL_DESCEND_ALT 10
 param set-default RTL_RETURN_ALT 30
@@ -61,9 +60,42 @@ param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_TYPE 2

+param set-default CA_AIRFRAME 2
+param set-default CA_ROTOR_COUNT 5
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2
+
+param set-default CA_SV_CS_COUNT 3
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+param set-default HIL_ACT_FUNC5 105
+param set-default HIL_ACT_FUNC6 201
+param set-default HIL_ACT_FUNC7 202
+param set-default HIL_ACT_FUNC8 203
+

 param set SYS_HITL 1

+param set UAVCAN_ENABLE 0
+
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -73,7 +105,7 @@ param set-default CBRK_SUPPLY_CHK 894281
 param set-default COM_PREARM_MODE 0
 param set-default CBRK_IO_SAFETY 22027

-set MAV_TYPE 22
+param set-default MAV_TYPE 22

 set MIXER standard_vtol_hitl

@@ -17,6 +17,23 @@ set PWM_OUT 1234

 param set UAVCAN_ENABLE 0

+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+
 # set SYS_HITL to 2 to start the SIH and avoid sensors startup
 param set SYS_HITL 2

@@ -17,6 +17,26 @@ set PWM_OUT 1234

 param set UAVCAN_ENABLE 0

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R 0.5
+param set-default CA_SV_CS0_TYPE 2
+param set-default CA_SV_CS1_TRQ_P 1.0
+param set-default CA_SV_CS1_TYPE 3
+param set-default CA_SV_CS2_TRQ_Y 1.0
+param set-default CA_SV_CS2_TYPE 4
+param set-default CA_SV_CS3_TYPE 10
+
+param set-default HIL_ACT_REV 2
+param set-default HIL_ACT_FUNC1 201
+param set-default HIL_ACT_FUNC2 202
+param set-default HIL_ACT_FUNC3 203
+param set-default HIL_ACT_FUNC4 101
+param set-default HIL_ACT_FUNC5 204
+param set-default HIL_ACT_FUNC6 400
+
 # set SYS_HITL to 2 to start the SIH and avoid sensors startup
 param set-default SYS_HITL 2

@@ -26,8 +26,28 @@ param set-default VT_FW_DIFTHR_SC 0.3
 param set-default MPC_MAN_Y_MAX 60
 param set-default MC_PITCH_P 5

+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 2
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PY 0.2
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PY -0.2
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.3
+param set-default CA_SV_CS0_TRQ_Y 0.3
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.3
+param set-default CA_SV_CS1_TRQ_Y -0.3
+param set-default CA_SV_CS1_TYPE 6
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC5 202
+param set-default HIL_ACT_FUNC6 201
+param set-default HIL_ACT_REV 32
+
 param set-default MAV_TYPE 19
-set MAV_TYPE 19
+
 set MIXER vtol_tailsitter_duo_sat

 set PWM_OUT 1234
@@ -1,48 +0,0 @@
-#!/bin/sh
-#
-# @name Steadidrone MAVRIK
-#
-# @type Octo Coax Wide
-# @class Copter
-#
-# @output MAIN1 motor 1
-# @output MAIN2 motor 2
-# @output MAIN3 motor 3
-# @output MAIN4 motor 4
-# @output MAIN5 motor 5
-# @output MAIN6 motor 6
-# @output MAIN7 motor 7
-# @output MAIN8 motor 8
-#
-# @maintainer Simon Wilks <simon@uaventure.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-
-param set-default MC_PITCH_P 4
-param set-default MC_PITCHRATE_P 0.24
-param set-default MC_PITCHRATE_I 0.09
-param set-default MC_PITCHRATE_D 0.013
-param set-default MC_PITCHRATE_MAX 180
-
-param set-default MC_ROLL_P 4
-param set-default MC_ROLLRATE_P 0.16
-param set-default MC_ROLLRATE_I 0.07
-param set-default MC_ROLLRATE_D 0.009
-param set-default MC_ROLLRATE_MAX 180
-
-param set-default MC_YAW_P 3
-
-param set-default MPC_HOLD_MAX_XY 0.25
-param set-default MPC_THR_MIN 0.15
-param set-default MPC_Z_VEL_MAX_DN 2
-
-param set-default BAT1_N_CELLS 4
-
-set MIXER octo_cox_w
-
-set PWM_OUT 12345678
@@ -24,13 +24,38 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default CA_AIRFRAME 2
+param set-default CA_ROTOR_COUNT 5
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TYPE 1
+param set-default CA_SV_CS0_TRQ_R -0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4

 param set-default PWM_AUX_DIS5 950

 param set-default VT_TYPE 2
 param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
-set MAV_TYPE 22
+
+param set-default MAV_TYPE 22

 set MIXER quad_x
 set MIXER_AUX vtol_AAERT
@@ -19,7 +19,6 @@

 . ${R}etc/init.d/rc.vtol_defaults

-
 param set-default MAV_TYPE 19

 param set-default MC_ROLL_P 6
@@ -38,7 +37,6 @@ param set-default VT_IDLE_PWM_MC  1080
 param set-default VT_ELEV_MC_LOCK 0
 param set-default VT_MOT_ID 12
 param set-default VT_TYPE 0
-set MAV_TYPE 19

 set MIXER vtol_tailsitter_duo

@@ -23,6 +23,7 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 21

 param set-default MC_ROLL_P 7
 param set-default MC_ROLLRATE_P 0.19
@@ -45,7 +46,6 @@ param set-default VT_TILT_TRANS 0.5
 param set-default VT_TILT_FW 0.9
 param set-default VT_ELEV_MC_LOCK 0
 param set-default VT_TYPE 1
-set MAV_TYPE 21

 set MIXER firefly6
 set MIXER_AUX firefly6
@@ -13,13 +13,33 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 20
+
+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.5
+param set-default CA_SV_CS0_TRQ_Y 0.5
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.5
+param set-default CA_SV_CS1_TRQ_Y -0.5
+param set-default CA_SV_CS1_TYPE 6

 param set-default PWM_MAIN_MAX 2000

 param set-default VT_MOT_ID 1234
 param set-default VT_IDLE_PWM_MC  1080
 param set-default VT_TYPE 0
-set MAV_TYPE 20

 set MIXER quad_x_vtol

@@ -7,8 +7,8 @@
 #
 # @output MAIN1 motor 1
 # @output MAIN2 motor 2
-# @output MAIN3 motor 4
-# @output MAIN4 motor 5
+# @output MAIN3 motor 3
+# @output MAIN4 motor 4
 # @output MAIN5 elevon left
 # @output MAIN6 elevon right
 # @output MAIN7 canard surface
@@ -22,13 +22,13 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 20
+
 param set-default PWM_MAIN_MAX 2000

 param set-default VT_IDLE_PWM_MC  1080
 param set-default VT_TYPE 0

-set MAV_TYPE 20
-
 set MIXER quad_+_vtol

 set PWM_OUT 1234
@@ -52,7 +52,6 @@ param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_IDLE_PWM_MC 1080
 param set-default VT_TYPE 2
-set MAV_TYPE 22

 set MIXER quad_x
 set MIXER_AUX vtol_AAERT
@@ -41,7 +41,6 @@ param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_F_TRANS_THR 0.75
 param set-default VT_IDLE_PWM_MC 1080
 param set-default VT_TYPE 2
-set MAV_TYPE 22

 set MIXER quad_x
 set MIXER_AUX vtol_delta
@@ -33,7 +33,6 @@ param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_IDLE_PWM_MC 1080
 param set-default VT_TYPE 2
-set MAV_TYPE 22

 set MIXER quad_x
 set MIXER_AUX vtol_AAVVT
@@ -46,7 +46,6 @@ param set-default VT_IDLE_PWM_MC 1080
 param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_TYPE 2
-set MAV_TYPE 22

 set MIXER quad_x
 set MIXER_AUX vtol_AAERT
@@ -77,8 +77,6 @@ param set-default VT_TRANS_MIN_TM 5
 param set-default VT_TRANS_TIMEOUT    30
 param set-default VT_TYPE 2

-set MAV_TYPE 22
-
 set MIXER quad_x
 set MIXER_AUX vtol_AAERT

@@ -1,36 +0,0 @@
-#!/bin/sh
-#
-# @name CruiseAder Claire
-#
-# @type VTOL Tiltrotor
-# @class VTOL
-#
-# @maintainer Samay Siga <samay_s@icloud.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.vtol_defaults
-
-param set-default PWM_AUX_DISARM 1000
-param set-default PWM_AUX_MAX 2000
-param set-default PWM_AUX_MIN 1000
-param set-default PWM_AUX_RATE 50
-
-param set-default PWM_MAIN_MAX 2000
-
-param set-default VT_MOT_ID 1234
-param set-default VT_FW_MOT_OFFID 13
-param set-default VT_IDLE_PWM_MC 1080
-param set-default VT_TILT_FW 0.9
-param set-default VT_TILT_MC 0.08
-param set-default VT_TILT_TRANS 0.5
-param set-default VT_ELEV_MC_LOCK 0
-param set-default VT_TYPE 1
-set MAV_TYPE 21
-
-set MIXER claire
-set MIXER_AUX claire
-
-set PWM_OUT 1234
@@ -22,6 +22,8 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 21
+
 param set-default CBRK_AIRSPD_CHK 162128

 param set-default FW_ARSP_MODE 1
@@ -64,8 +66,12 @@ param set-default VT_TRANS_MIN_TM 1.2
 param set-default VT_TRANS_P2_DUR 1.3
 param set-default VT_ELEV_MC_LOCK 0
 param set-default VT_TYPE 1
-set MAV_TYPE 21

 set MIXER vtol_convergence

-set PWM_OUT 1234
+if ! ver hwcmp MATEK_H743
+then
+	set PWM_OUT 1234
+else
+	set PWM_OUT 3456
+fi	
@@ -22,6 +22,8 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 22
+
 param set-default BAT1_CAPACITY 23000
 param set-default BAT1_N_CELLS 4
 param set-default BAT1_R_INTERNAL 0.0025
@@ -129,12 +131,10 @@ param set-default VT_F_TRANS_DUR 1
 param set-default VT_IDLE_PWM_MC 1025
 param set-default VT_B_REV_OUT 0.5
 param set-default VT_B_TRANS_THR 0.7
-param set-default VT_FW_PERM_STAB 1
 param set-default VT_TRANS_TIMEOUT 22
 param set-default VT_F_TRANS_RAMP 4

 param set-default COM_RC_OVERRIDE 0
-set MAV_TYPE 22

 set MIXER deltaquad
 set MIXER_AUX pass
@@ -23,6 +23,8 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 22
+
 param set-default BAT1_N_CELLS 6

 param set-default FW_AIRSPD_MAX 30
@@ -94,8 +96,6 @@ param set-default VT_PSHER_RMP_DT 2
 param set-default VT_TRANS_MIN_TM 4
 param set-default VT_TYPE 2

-set MAV_TYPE 22
-
 set MIXER babyshark
 set MIXER_AUX pass

@@ -27,11 +27,37 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 21
+
 param set-default VT_IDLE_PWM_MC 1100
 param set-default VT_TYPE 1
 param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 24
-set MAV_TYPE 21
+
+param set-default CA_AIRFRAME 3
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR0_TILT 1
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR1_TILT 2
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR2_TILT 3
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR3_TILT 4
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4
+param set-default CA_SV_TL_COUNT 4

 set MIXER quad_x
 set MIXER_AUX vtol_TTTTAAER
@@ -31,7 +31,6 @@ param set-default PWM_AUX_DIS5 950
 param set-default VT_TYPE 2
 param set-default VT_MOT_ID 12345678
 param set-default VT_FW_MOT_OFFID 12345678
-set MAV_TYPE 22

 set MIXER octo_cox
 set MIXER_AUX vtol_AAERT
@@ -19,12 +19,26 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default MAV_TYPE 19
+
 param set-default VT_ELEV_MC_LOCK 0
 param set-default VT_MOT_COUNT 2
 param set-default VT_TYPE 0

-param set-default MAV_TYPE 19
-set MAV_TYPE 19
+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 2
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PY 0.2
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PY -0.2
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.5
+param set-default CA_SV_CS0_TRQ_Y 0.5
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.5
+param set-default CA_SV_CS1_TRQ_Y -0.5
+param set-default CA_SV_CS1_TYPE 6
+
 set MIXER vtol_tailsitter_duo

 set PWM_OUT 1234
@@ -18,4 +18,7 @@

 . ${R}etc/init.d/rc.mc_defaults

+# MAV_TYPE_TRICOPTER 15
+param set-default MAV_TYPE 15
+
 set MIXER tri_y_yaw+
@@ -18,4 +18,7 @@

 . ${R}etc/init.d/rc.mc_defaults

+# MAV_TYPE_TRICOPTER 15
+param set-default MAV_TYPE 15
+
 set MIXER tri_y_yaw-
@@ -17,7 +17,9 @@
 #

 . ${R}etc/init.d/rc.mc_defaults
-set MIXER coax
+
+# MAV_TYPE_COAXIAL 3
+param set-default MAV_TYPE 3

 param set-default MC_ROLLRATE_P 0.17
 param set-default MC_ROLLRATE_I 0.05
@@ -36,6 +38,9 @@ param set-default PWM_MAIN_RATE 400

 param set-default RTL_RETURN_ALT 30
 param set-default RTL_DESCEND_ALT 10
+
+set MIXER coax
+
 # This is the gimbal pass mixer
 set MIXER_AUX pass

@@ -20,7 +20,7 @@
 . ${R}etc/init.d/rc.mc_defaults

 # Configure as helicopter (number 4 defined in commander_helper.cpp)
-set MAV_TYPE 4
+param set-default MAV_TYPE 4

 set MIXER blade130

@@ -41,5 +41,6 @@ param set-default FW_R_LIM 40
 param set-default FW_P_LIM_MAX 25
 param set-default FW_P_LIM_MIN -5
 param set-default FW_P_RMAX_NEG 20
+
 set MIXER TF-G2
 set MIXER_AUX pass
@@ -24,8 +24,5 @@ param set-default MAV_0_CONFIG 102
 param set-default GPS_UBX_DYNMODEL 8
 param set-default SER_TEL2_BAUD 9600

-set MAV_TYPE 8
-param set MAV_TYPE ${MAV_TYPE}
-
 set MIXER IO_pass
 set MIXER_AUX pass
@@ -23,6 +23,18 @@

 . ${R}etc/init.d/rc.fw_defaults

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R -0.5
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4
+
 param set-default PWM_AUX_RATE 50
 param set-default PWM_MAIN_RATE 50

@@ -0,0 +1,21 @@
+#!/bin/sh
+#
+# @name Generic Output
+#
+# @maintainer
+#
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.output_defaults
+
+
+# Provide ESC a constant 1500 us pulse
+param set-default PWM_MAIN_DISARM 1500
+param set-default PWM_MAIN_MAX 2000
+param set-default PWM_MAIN_MIN 1000
+
+# Set mixer
+set MIXER IO_pass
+
+set PWM_OUT 12
@@ -26,7 +26,7 @@
 # @board px4_fmu-v2 exclude
 #

-set VEHICLE_TYPE mc
+. ${R}etc/init.d/rc.mc_defaults

 param set-default NAV_ACC_RAD 2

@@ -39,6 +39,7 @@ param set-default PWM_MAIN_RATE 400

 param set-default RTL_DESCEND_ALT 10
 param set-default RTL_RETURN_ALT 30
+
 set MIXER dodeca_top_cox
 set MIXER_AUX dodeca_bottom_cox

@@ -1,45 +0,0 @@
-#!/bin/sh
-#
-# @name IO Camflyer
-#
-# @type Flying Wing
-# @class Plane
-#
-# @output MAIN1 left aileron
-# @output MAIN2 right aileron
-# @output MAIN4 throttle
-#
-# @output AUX1 feed-through of RC AUX1 channel
-# @output AUX2 feed-through of RC AUX2 channel
-# @output AUX3 feed-through of RC AUX3 channel
-#
-# @maintainer Simon Wilks <simon@uaventure.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.fw_defaults
-
-param set-default FW_AIRSPD_MAX 15
-param set-default FW_AIRSPD_TRIM 13
-param set-default FW_R_TC 0.3
-param set-default FW_P_TC 0.3
-param set-default FW_L1_DAMPING 0.74
-param set-default FW_L1_PERIOD 16
-param set-default FW_LND_ANG 15
-param set-default FW_LND_FLALT 5
-param set-default FW_LND_HVIRT 13
-param set-default FW_LND_TLALT 5
-param set-default FW_THR_LND_MAX 0
-param set-default FW_PR_FF 0.35
-param set-default FW_RR_FF 0.6
-param set-default FW_RR_P 0.04
-
-param set-default PWM_MAIN_DISARM 1000
-
-
-set MIXER fw_generic_wing
-
-# Provide ESC a constant 1000 us pulse while disarmed
-set PWM_OUT 4
@@ -41,9 +41,6 @@ param set-default FW_RR_P 0.04

 param set-default PWM_MAIN_DISARM 1000

-# Configure this as plane.
-set MAV_TYPE 1
-
 # Set mixer.
 set MIXER fw_generic_wing

@@ -1,29 +0,0 @@
-#!/bin/sh
-#
-# @name FX-79 Buffalo Flying Wing
-#
-# @type Flying Wing
-# @class Plane
-#
-# @output MAIN1 right aileron
-# @output MAIN2 left aileron
-# @output MAIN4 throttle
-#
-# @output AUX1 feed-through of RC AUX1 channel
-# @output AUX2 feed-through of RC AUX2 channel
-# @output AUX3 feed-through of RC AUX3 channel
-#
-# @maintainer Simon Wilks <simon@uaventure.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.fw_defaults
-
-param set-default FW_AIRSPD_MAX 30
-param set-default FW_AIRSPD_MIN 13
-
-param set-default NAV_LOITER_RAD 150
-
-set MIXER fw_generic_wing
@@ -1,23 +0,0 @@
-#!/bin/sh
-#
-# @name Viper
-#
-# @type Flying Wing
-# @class Plane
-# @output MAIN1 left aileron
-# @output MAIN2 right aileron
-# @output MAIN4 throttle
-#
-# @output AUX1 feed-through of RC AUX1 channel
-# @output AUX2 feed-through of RC AUX2 channel
-# @output AUX3 feed-through of RC AUX3 channel
-#
-# @maintainer Simon Wilks <simon@uaventure.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.fw_defaults
-
-set MIXER Viper
@@ -1,53 +0,0 @@
-#!/bin/sh
-#
-# @name Modified Parrot Disco
-#
-# @url
-#
-# @type Flying Wing
-# @class Plane
-#
-# @output MAIN1 left aileron
-# @output MAIN2 right aileron
-# @output MAIN4 throttle
-#
-# @output AUX1 feed-through of RC AUX1 channel
-# @output AUX2 feed-through of RC AUX2 channel
-# @output AUX3 feed-through of RC AUX3 channel
-#
-# @maintainer Jan Liphardt <JTLiphardt@gmail.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.fw_defaults
-
-####################################
-# Airspeed
-####################################
-param set-default FW_AIRSPD_MAX  27 # = 52 knots
-
-####################################
-# Pitch
-####################################
-
-# Pitch rate feed forward (def = 0.5 %/rad/sec)
-param set-default FW_PR_FF 0.35
-
-####################################
-# Roll
-####################################
-
-# Basic limits (def = 50 deg)
-param set-default FW_R_LIM 40
-
-# Roll rate upper limit (def = 70 deg/s)
-param set-default FW_R_RMAX 50
-
-param set-default PWM_MAIN_DISARM 1000
-
-set MIXER fw_generic_wing.main.mix
-
-# Provide ESC a constant 1000 us pulse
-set PWM_OUT 4
@@ -21,3 +21,16 @@
 #

 . ${R}etc/init.d/rc.mc_defaults
+
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
@@ -1,21 +0,0 @@
-#!/bin/sh
-#
-# @name DJI F330 w/ DJI ESCs
-#
-# @type Quadrotor x
-# @class Copter
-#
-# @maintainer Lorenz Meier <lorenz@px4.io>
-# @board px4_fmu-v2 exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default MC_ROLL_P 7
-param set-default MC_ROLLRATE_I 0.05
-param set-default MC_PITCH_P 7
-param set-default MC_PITCHRATE_I 0.05
-
-
-# DJI ESCs do not support calibration and need a higher min
-param set-default PWM_MAIN_MIN 1230
@@ -1,20 +0,0 @@
-#!/bin/sh
-#
-# @name DJI F450 w/ DJI ESCs
-#
-# @type Quadrotor x
-# @class Copter
-#
-# @maintainer Lorenz Meier <lorenz@px4.io>
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default MC_ROLL_P 7
-param set-default MC_ROLLRATE_I 0.05
-param set-default MC_PITCH_P 7
-param set-default MC_PITCHRATE_I 0.05
-param set-default MC_YAWRATE_P 0.3
-
-# DJI ESCs do not support calibration and need a higher min
-param set-default PWM_MAIN_MIN 1230
@@ -1,39 +0,0 @@
-#!/bin/sh
-#
-# @name S500 with control allocation
-#
-# @type Quadrotor x
-# @class Copter
-#
-# @maintainer Silvan Fuhrer
-#
-# @board px4_fmu-v2 exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-set MIXER skip
-set MIXER_AUX none
-
-param set-default SYS_CTRL_ALLOC 1
-
-param set-default CA_AIRFRAME 0
-
-param set-default CA_ROTOR_COUNT 4
-param set-default CA_ROTOR0_PX 0.177
-param set-default CA_ROTOR0_PY 0.177
-param set-default CA_ROTOR0_KM 0.05
-param set-default CA_ROTOR1_PX -0.177
-param set-default CA_ROTOR1_PY -0.177
-param set-default CA_ROTOR1_KM 0.05
-param set-default CA_ROTOR2_PX 0.177
-param set-default CA_ROTOR2_PY -0.177
-param set-default CA_ROTOR2_KM -0.05
-param set-default CA_ROTOR3_PX -0.177
-param set-default CA_ROTOR3_PY 0.177
-param set-default CA_ROTOR3_KM -0.05
-
-param set-default PWM_MAIN_FUNC1 101
-param set-default PWM_MAIN_FUNC2 102
-param set-default PWM_MAIN_FUNC3 103
-param set-default PWM_MAIN_FUNC4 104
@@ -24,8 +24,6 @@

 set MIXER quad_s250aq

-set MAV_TYPE 2
-
 param set-default ATT_BIAS_MAX 0

 param set-default CBRK_IO_SAFETY 22027
@@ -1,27 +0,0 @@
-#!/bin/sh
-#
-# @name DJI Matrice 100
-#
-# @type Quadrotor x
-# @class Copter
-#
-# @maintainer James Goppert <james.goppert@gmail.com>
-#
-# @board px4_fmu-v2 exclude
-# @board bitcraze_crazyflie exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default BAT1_N_CELLS 6
-
-param set-default MC_ROLLRATE_P 0.05
-param set-default MC_ROLLRATE_I 0.05
-param set-default MC_ROLLRATE_D 0.001
-param set-default MC_PITCHRATE_P 0.05
-param set-default MC_PITCHRATE_I 0.05
-param set-default MC_PITCHRATE_D 0.001
-
-param set-default MC_YAWRATE_I 0
-
-param set-default PWM_MAIN_MIN 1200
@@ -46,7 +46,7 @@ param set-default COM_RC_LOSS_T 3


 # ekf2
-param set-default EKF2_AID_MASK 35
+param set-default EKF2_AID_MASK 33
 param set-default EKF2_BARO_DELAY 0
 param set-default EKF2_BARO_NOISE 2.0

@@ -147,7 +147,7 @@ param set-default MPC_Z_VEL_P 0.27


 # gimbal configuration
-param set-default MNT_MODE_IN 1
+param set-default MNT_MODE_IN 0
 param set-default MNT_MODE_OUT 1
 param set-default MNT_MAN_PITCH 2
 param set-default MNT_RC_IN_MODE 1
@@ -164,6 +164,8 @@ param set-default RC_MAP_AUX2       5
 param set-default RC_MAP_AUX3       10
 param set-default RC_MAP_AUX4       8
 param set-default RC_MAP_FLTMODE    6
+param set-default RC_MAP_RETURN_SW  7
+
 param set-default RC1_TRIM          1000


@@ -21,10 +21,7 @@
 # @board cuav_x7pro exclude
 #

-set VEHICLE_TYPE mc
-set MIXER quad_x
-set PWM_OUT 1234
-
+. ${R}etc/init.d/rc.mc_defaults

 # Attitude & rate gains
 param set-default MC_ROLLRATE_D 0.0013
@@ -21,10 +21,7 @@
 # @maintainer Hyon Lim <lim@uvify.com>
 #

-set VEHICLE_TYPE mc
-set MIXER quad_x
-set PWM_OUT 1234
-
+. ${R}etc/init.d/rc.mc_defaults

 # Attitude & rate gains
 param set-default MC_ROLLRATE_D 0.0013
@@ -24,10 +24,6 @@

 . ${R}etc/init.d/rc.mc_defaults

-
-# Configure this as Quadrotor
-# set MAV_TYPE 14
-
 # Set mixer
 set MIXER tilt_quad
 set MIXER_AUX tilt_quad
@@ -48,8 +48,6 @@ param set-default NAV_ACC_RAD 0.5
 param set-default PWM_MAIN_DISARM 1500
 param set-default PWM_MAIN_MAX 2000
 param set-default PWM_MAIN_MIN 1000
-# Configure this as rover
-set MAV_TYPE 10

 # Set mixer
 set MIXER rover_generic
@@ -76,9 +76,6 @@ param set-default RBCLW_SER_CFG 104
 # Start this driver after setting parameters, because the driver uses some of those parameters.
 # roboclaw start /dev/ttyS3

-# Configure this as rover
-set MAV_TYPE 10
-
 # Set mixer
 set MIXER generic_diff_rover

@@ -65,9 +65,6 @@ param set-default PWM_MAIN_MIN4 970
 # Enable Airspeed check circuit breaker because Rovers will have no airspeed sensor
 param set-default CBRK_AIRSPD_CHK 162128

-# Configure this as rover
-set MAV_TYPE 10
-
 # Set mixer
 set MIXER rover_diff_and_servo

@@ -16,7 +16,4 @@
 # disable circuit breaker for airspeed sensor
 param set-default CBRK_AIRSPD_CHK 162128

-set MAV_TYPE 12
-param set MAV_TYPE ${MAV_TYPE}
-
 set MIXER uuv_x
@@ -16,7 +16,4 @@
 # disable circuit breaker for airspeed sensor
 param set-default CBRK_AIRSPD_CHK 162128

-set MAV_TYPE 12
-param set MAV_TYPE ${MAV_TYPE}
-
 set MIXER uuv_x
@@ -23,6 +23,26 @@

 . ${R}etc/init.d/rc.mc_defaults

+# MAV_TYPE_HEXAROTOR 13
+param set-default MAV_TYPE 13
+
+param set-default CA_ROTOR_COUNT 6
+param set-default CA_ROTOR0_PX 0.0
+param set-default CA_ROTOR0_PY 0.5
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR1_PX 0.0
+param set-default CA_ROTOR1_PY -0.5
+param set-default CA_ROTOR2_PX 0.43
+param set-default CA_ROTOR2_PY -0.25
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.43
+param set-default CA_ROTOR3_PY 0.25
+param set-default CA_ROTOR4_PX 0.43
+param set-default CA_ROTOR4_PY 0.25
+param set-default CA_ROTOR5_PX -0.43
+param set-default CA_ROTOR5_PY -0.25
+param set-default CA_ROTOR5_KM -0.05
+
 set MIXER hexa_x

 # Need to set all 8 channels
@@ -27,9 +27,8 @@

 . ${R}etc/init.d/rc.mc_defaults

-set MIXER hexa_x
-set PWM_OUT 12345678
-
+# MAV_TYPE_HEXAROTOR 13
+param set-default MAV_TYPE 13

 ###############################################
 # Attitude & rate gains
@@ -120,3 +119,7 @@ param set-default MAV_1_MODE 2
 param set-default MAV_1_FORWARD 1
 param set-default MAV_1_RATE 800000
 param set-default SER_TEL2_BAUD 921600
+
+
+set MIXER hexa_x
+set PWM_OUT 12345678
@@ -1,52 +0,0 @@
-#!/bin/sh
-#
-# @name Hex X with control allocation
-#
-# @type Hexarotor x
-# @class Copter
-#
-# @maintainer Silvan Fuhrer
-#
-# @board px4_fmu-v2 exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default SYS_CTRL_ALLOC 1
-
-param set-default CA_AIRFRAME 0
-param set-default CA_ROTOR_COUNT 6
-
-param set-default CA_ROTOR0_PX 0.0
-param set-default CA_ROTOR0_PY 0.275
-param set-default CA_ROTOR0_KM -0.05
-
-param set-default CA_ROTOR1_PX 0.0
-param set-default CA_ROTOR1_PY -0.275
-param set-default CA_ROTOR1_KM 0.05
-
-param set-default CA_ROTOR2_PX 0.238
-param set-default CA_ROTOR2_PY -0.1375
-param set-default CA_ROTOR2_KM -0.05
-
-param set-default CA_ROTOR3_PX -0.238
-param set-default CA_ROTOR3_PY 0.1375
-param set-default CA_ROTOR3_KM 0.05
-
-param set-default CA_ROTOR4_PX 0.238
-param set-default CA_ROTOR4_PY 0.1375
-param set-default CA_ROTOR4_KM 0.05
-
-param set-default CA_ROTOR5_PX -0.238
-param set-default CA_ROTOR5_PY -0.1375
-param set-default CA_ROTOR5_KM -0.05
-
-param set-default PWM_MAIN_FUNC1 101
-param set-default PWM_MAIN_FUNC2 102
-param set-default PWM_MAIN_FUNC3 103
-param set-default PWM_MAIN_FUNC4 104
-param set-default PWM_MAIN_FUNC5 105
-param set-default PWM_MAIN_FUNC6 106
-
-set MIXER skip
-set MIXER_AUX none
@@ -23,6 +23,26 @@

 . ${R}etc/init.d/rc.mc_defaults

+# MAV_TYPE_HEXAROTOR 13
+param set-default MAV_TYPE 13
+
+param set-default CA_ROTOR_COUNT 6
+param set-default CA_ROTOR0_PX 0.5
+param set-default CA_ROTOR0_PY 0.0
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR1_PX -0.5
+param set-default CA_ROTOR1_PY 0.0
+param set-default CA_ROTOR2_PX -0.25
+param set-default CA_ROTOR2_PY -0.43
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX 0.25
+param set-default CA_ROTOR3_PY 0.43
+param set-default CA_ROTOR4_PX 0.25
+param set-default CA_ROTOR4_PY -0.43
+param set-default CA_ROTOR5_PX -0.25
+param set-default CA_ROTOR5_PY 0.43
+param set-default CA_ROTOR5_KM -0.05
+
 set MIXER hexa_+

 # Need to set all 8 channels
@@ -25,6 +25,31 @@

 . ${R}etc/init.d/rc.mc_defaults

+# MAV_TYPE_OCTOROTOR 14
+param set-default MAV_TYPE 14
+
+param set-default CA_ROTOR_COUNT 8
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PX 0.46
+param set-default CA_ROTOR0_PY 0.19
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PX -0.46
+param set-default CA_ROTOR1_PY -0.19
+param set-default CA_ROTOR2_PX 0.19
+param set-default CA_ROTOR2_PY 0.46
+param set-default CA_ROTOR3_PX -0.46
+param set-default CA_ROTOR3_PY 0.19
+param set-default CA_ROTOR4_PX 0.46
+param set-default CA_ROTOR4_PY -0.19
+param set-default CA_ROTOR5_PX -0.19
+param set-default CA_ROTOR5_PY -0.46
+param set-default CA_ROTOR6_KM -0.05
+param set-default CA_ROTOR6_PX 0.19
+param set-default CA_ROTOR6_PY -0.46
+param set-default CA_ROTOR7_KM -0.05
+param set-default CA_ROTOR7_PX -0.19
+param set-default CA_ROTOR7_PY 0.46
+
 set MIXER octo_x

 set PWM_OUT 12345678
--- a/Show More
+++ b/Show More