fixup! Update submodule nuttx

uavcan_v1: Add Publishers dir to includes
uavcan_v1: SocketCAN set 'can_fd' based on CONFIG
2026-05-25 05:37:35 +08:00 · 2022-03-18 10:56:44 -07:00 · 2022-03-18 09:03:48 -07:00 · 2022-03-18 09:03:06 -07:00 · 2022-03-18 09:02:00 -07:00 · 2022-03-17 17:01:54 -07:00
731 changed files with 31227 additions and 14133 deletions
@@ -60,6 +60,8 @@ pipeline {
                     "holybro_kakutef7_default",
                     "holybro_pix32v5_default",
                     "matek_h743-slim",
+                     "matek_gnss-m9n-f4_canbootloader",
+                     "matek_gnss-m9n-f4_default",
                     "modalai_fc-v1_default",
                     "modalai_fc-v1_rtps",
                     "modalai_fc-v2_default",
@@ -73,10 +73,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/cubepilot_cubeorange_test/cubepilot_cubeorange_test.elf || true'
                }
              }
@@ -145,10 +143,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/cuav_x7pro_test/cuav_x7pro_test.elf || true'
                }
              }
@@ -217,10 +213,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v3_test/px4_fmu-v3_test.elf || true'
                }
              }
@@ -288,10 +282,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v4_test/px4_fmu-v4_test.elf || true'
                }
              }
@@ -360,10 +352,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v4pro_test/px4_fmu-v4pro_test.elf || true'
                }
              }
@@ -452,10 +442,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_debug/px4_fmu-v5_debug.elf || true'
                }
              }
@@ -536,10 +524,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_stackcheck/px4_fmu-v5_stackcheck.elf || true'
                }
              }
@@ -608,10 +594,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/px4_fmu-v5_test/px4_fmu-v5_test.elf || true'
                }
              }
@@ -680,10 +664,8 @@ pipeline {
                }
              }
              post {
-                failure {
-                  sh 'cat /tmp/pyserial_spy_file.txt'
-                }
                always {
+                  sh 'cat /tmp/pyserial_spy_file.txt || true'
                  sh './platforms/nuttx/Debug/jlink_gdb_backtrace_simple.sh build/nxp_fmuk66-v3_test/nxp_fmuk66-v3_test.elf || true'
                }
              }
@@ -743,8 +725,10 @@ void checkStatus() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param save"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param status"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show SYS*"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump"'
  sh './Tools/HIL/reboot.py --device `find /dev/serial -name *usb-*`' // reboot to apply
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show SYS*"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump"'

  // run logger
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "logger on"'
@@ -778,6 +762,7 @@ void checkStatus() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mavlink status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mount"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mtd status"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param status"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "perf latency"'
@@ -789,8 +774,8 @@ void checkStatus() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sensors status"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "top once"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uavcan status" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb status"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb status" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "ver all"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "work_queue status"'
  // stop logger
@@ -806,7 +791,7 @@ void resetParameters() {
 void runTests() {

  // test loading a range of airframes
-  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 1000 1001 2100 3000 4001 4018 6001 8001 10016'
+  sh './Tools/HIL/test_airframes.sh `find /dev/serial -name *usb-*` 1000 1001 2100 3000 4001 6001 8001 10016'

  resetParameters()

@@ -859,7 +844,7 @@ void runTests() {
 void printTopics() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "ls /obj"'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb status"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "uorb top -1 -a" || true'

  // these are for casually inspecting the system, output failure doesn't matter
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener actuator_armed" || true'
@@ -876,7 +861,7 @@ void printTopics() {
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener cpuload" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener distance_sensor" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener ekf2_timestamps" || true'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener ekf_gps_drift" || true'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_gps_status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener esc_status" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_attitude" || true'
  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "listener estimator_baro_bias" || true'
@@ -33,8 +33,10 @@ jobs:
          holybro_can-gps-v1,
          holybro_durandal-v1,
          holybro_kakutef7,
+          holybro_kakuteh7,
          holybro_pix32v5,
          matek_h743-slim,
+          matek_gnss-m9n-f4,
          modalai_fc-v1,
          modalai_fc-v2,
          mro_ctrl-zero-f7,
@@ -24,8 +24,8 @@
 	branch = master
 [submodule "platforms/nuttx/NuttX/nuttx"]
 	path = platforms/nuttx/NuttX/nuttx
-	url = https://github.com/PX4/NuttX.git
-	branch = px4_firmware_nuttx-10.1.0+
+	url = https://github.com/JacobCrabill/incubator-nuttx.git
+	branch = dev-h7-socketcan
 [submodule "platforms/nuttx/NuttX/apps"]
 	path = platforms/nuttx/NuttX/apps
 	url = https://github.com/PX4/NuttX-apps.git
@@ -196,6 +196,16 @@ CONFIG:
      buildType: MinSizeRel
      settings:
        CONFIG: matek_h743-slim_default
+    matek_gnss-m9n-f4_canbootloader:
+      short: matek_gnss-m9n-f4_canbootloader
+      buildType: MiniSizeRel
+      settings:
+        CONFIG: matek_m9nf4can_canbootloader
+    matek_gnss-m9n-f4_default:
+      short: matek_gnss-m9n-f4_default
+      buildType: MiniSizeRel
+      settings:
+        CONFIG: matek_gnss-m9n-f4_default
    modalai_fc-v1_default:
      short: modalai_fc-v1
      buildType: MinSizeRel
@@ -125,6 +125,11 @@ define_property(GLOBAL PROPERTY PX4_MODULE_LIBRARIES
                 FULL_DOCS "List of all PX4 module libraries"
                 )

+define_property(GLOBAL PROPERTY PX4_KERNEL_MODULE_LIBRARIES
+                 BRIEF_DOCS "PX4 kernel side module libs"
+                 FULL_DOCS "List of all PX4 kernel module libraries"
+                 )
+
 define_property(GLOBAL PROPERTY PX4_MODULE_PATHS
                 BRIEF_DOCS "PX4 module paths"
                 FULL_DOCS "List of paths to all PX4 modules"
@@ -142,6 +147,7 @@ set(CONFIG "px4_sitl_default" CACHE STRING "desired configuration")

 include(px4_add_module)
 set(config_module_list)
+set(config_kernel_list)

 # Find Python
 # If using catkin, Python 2 is found since it points
@@ -118,6 +118,11 @@ config BOARD_CRYPTO
    help
        Enable PX4 Crypto Support. Select the implementation under drivers

+config BOARD_PROTECTED
+    bool "Memory protection"
+    help
+        Enable memory protection via MPU/MMU
+
 menu "Serial ports"

    config BOARD_SERIAL_URT6
@@ -1,6 +1,6 @@
 BSD 3-Clause License

-Copyright (c) 2012 - 2021, PX4 Development Team
+Copyright (c) 2012 - 2022, PX4 Development Team
 All rights reserved.

 Redistribution and use in source and binary forms, with or without
@@ -44,6 +44,8 @@ param set-default MIS_TAKEOFF_ALT 30
 param set-default NAV_ACC_RAD 15
 param set-default NAV_DLL_ACT 2

+param set-default FW_USE_NPFG 1
+
 param set-default RWTO_TKOFF 1

 set MIXER_FILE etc/mixers-sitl/plane_sitl.main.mix
@@ -10,7 +10,7 @@
 # param set-default SYS_CTRL_ALLOC 1
 param set-default CA_AIRFRAME 2

-param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR_COUNT 5
 param set-default CA_ROTOR0_PX 0.1515
 param set-default CA_ROTOR0_PY 0.245
 param set-default CA_ROTOR0_KM 0.05
@@ -23,6 +23,9 @@ param set-default CA_ROTOR2_KM -0.05
 param set-default CA_ROTOR3_PX -0.1515
 param set-default CA_ROTOR3_PY 0.1875
 param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2

 param set-default CA_SV_CS_COUNT 3
 param set-default CA_SV_CS0_TYPE 1
@@ -10,7 +10,7 @@ fi

 if [ ! -f replay_params.txt ]; then
 	echo "Creating $(pwd)/replay_params.txt"
-	ulog_params -i "${replay}" -d ' ' | grep -e '^EKF2' > replay_params.txt
+	ulog_params -i "${replay}" -l ' ' | grep -e '^EKF2' > replay_params.txt
 fi

 publisher_rules_file="orb_publisher.rules"
@@ -21,6 +21,7 @@ ignore_others: false
 EOF

 param set SDLOG_DIRS_MAX 7
+param set SDLOG_PROFILE 3

 # apply all params before ekf starts, as some params cannot be changed after startup
 replay tryapplyparams
@@ -234,7 +234,7 @@ fi

 if param greater -s MNT_MODE_IN -1
 then
-	vmount start
+	gimbal start
 fi

 if param greater -s TRIG_MODE 0
@@ -39,6 +39,26 @@ param set-default FW_RR_P 0.3

 param set-default RWTO_TKOFF 1

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R 0.5
+param set-default CA_SV_CS0_TYPE 2
+param set-default CA_SV_CS1_TRQ_P 1.0
+param set-default CA_SV_CS1_TYPE 3
+param set-default CA_SV_CS2_TRQ_Y 1.0
+param set-default CA_SV_CS2_TYPE 4
+param set-default CA_SV_CS3_TYPE 10
+
+param set-default HIL_ACT_REV 2
+param set-default HIL_ACT_FUNC1 201
+param set-default HIL_ACT_FUNC2 202
+param set-default HIL_ACT_FUNC3 203
+param set-default HIL_ACT_FUNC4 101
+param set-default HIL_ACT_FUNC5 204
+param set-default HIL_ACT_FUNC6 400
+
 param set SYS_HITL 1

 # disable some checks to allow to fly
@@ -15,6 +15,23 @@ set MIXER quad_x

 param set SYS_HITL 1

+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+
 # disable some checks to allow to fly
 # - with usb
 param set-default CBRK_USB_CHK 197848
@@ -61,6 +61,37 @@ param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 1234
 param set-default VT_TYPE 2

+param set-default CA_AIRFRAME 2
+param set-default CA_ROTOR_COUNT 5
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2
+
+param set-default CA_SV_CS_COUNT 3
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+param set-default HIL_ACT_FUNC5 105
+param set-default HIL_ACT_FUNC6 201
+param set-default HIL_ACT_FUNC7 202
+param set-default HIL_ACT_FUNC8 203
+

 param set SYS_HITL 1

@@ -17,6 +17,23 @@ set PWM_OUT 1234

 param set UAVCAN_ENABLE 0

+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC3 103
+param set-default HIL_ACT_FUNC4 104
+
 # set SYS_HITL to 2 to start the SIH and avoid sensors startup
 param set SYS_HITL 2

@@ -17,6 +17,26 @@ set PWM_OUT 1234

 param set UAVCAN_ENABLE 0

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R 0.5
+param set-default CA_SV_CS0_TYPE 2
+param set-default CA_SV_CS1_TRQ_P 1.0
+param set-default CA_SV_CS1_TYPE 3
+param set-default CA_SV_CS2_TRQ_Y 1.0
+param set-default CA_SV_CS2_TYPE 4
+param set-default CA_SV_CS3_TYPE 10
+
+param set-default HIL_ACT_REV 2
+param set-default HIL_ACT_FUNC1 201
+param set-default HIL_ACT_FUNC2 202
+param set-default HIL_ACT_FUNC3 203
+param set-default HIL_ACT_FUNC4 101
+param set-default HIL_ACT_FUNC5 204
+param set-default HIL_ACT_FUNC6 400
+
 # set SYS_HITL to 2 to start the SIH and avoid sensors startup
 param set-default SYS_HITL 2

@@ -26,6 +26,26 @@ param set-default VT_FW_DIFTHR_SC 0.3
 param set-default MPC_MAN_Y_MAX 60
 param set-default MC_PITCH_P 5

+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 2
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PY 0.2
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PY -0.2
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.3
+param set-default CA_SV_CS0_TRQ_Y 0.3
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.3
+param set-default CA_SV_CS1_TRQ_Y -0.3
+param set-default CA_SV_CS1_TYPE 6
+
+param set-default HIL_ACT_FUNC1 101
+param set-default HIL_ACT_FUNC2 102
+param set-default HIL_ACT_FUNC5 202
+param set-default HIL_ACT_FUNC6 201
+param set-default HIL_ACT_REV 32
+
 param set-default MAV_TYPE 19
 set MAV_TYPE 19
 set MIXER vtol_tailsitter_duo_sat
@@ -24,6 +24,30 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default CA_AIRFRAME 2
+param set-default CA_ROTOR_COUNT 5
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR4_AX 1.0
+param set-default CA_ROTOR4_AZ 0.0
+param set-default CA_ROTOR4_PX 0.2
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TYPE 1
+param set-default CA_SV_CS0_TRQ_R -0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4

 param set-default PWM_AUX_DIS5 950

@@ -13,6 +13,25 @@

 . ${R}etc/init.d/rc.vtol_defaults

+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.5
+param set-default CA_SV_CS0_TRQ_Y 0.5
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.5
+param set-default CA_SV_CS1_TRQ_Y -0.5
+param set-default CA_SV_CS1_TYPE 6

 param set-default PWM_MAIN_MAX 2000

@@ -31,6 +31,32 @@ param set-default VT_IDLE_PWM_MC 1100
 param set-default VT_TYPE 1
 param set-default VT_MOT_ID 1234
 param set-default VT_FW_MOT_OFFID 24
+
+param set-default CA_AIRFRAME 3
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR0_TILT 1
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR1_TILT 2
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR2_TILT 3
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+param set-default CA_ROTOR3_TILT 4
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4
+param set-default CA_SV_TL_COUNT 4
+
 set MAV_TYPE 21

 set MIXER quad_x
@@ -23,6 +23,20 @@ param set-default VT_ELEV_MC_LOCK 0
 param set-default VT_MOT_COUNT 2
 param set-default VT_TYPE 0

+param set-default CA_AIRFRAME 4
+param set-default CA_ROTOR_COUNT 2
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PY 0.2
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PY -0.2
+param set-default CA_SV_CS_COUNT 2
+param set-default CA_SV_CS0_TRQ_P 0.5
+param set-default CA_SV_CS0_TRQ_Y 0.5
+param set-default CA_SV_CS0_TYPE 5
+param set-default CA_SV_CS1_TRQ_P 0.5
+param set-default CA_SV_CS1_TRQ_Y -0.5
+param set-default CA_SV_CS1_TYPE 6
+
 param set-default MAV_TYPE 19
 set MAV_TYPE 19
 set MIXER vtol_tailsitter_duo
@@ -23,6 +23,18 @@

 . ${R}etc/init.d/rc.fw_defaults

+param set-default CA_AIRFRAME 1
+param set-default CA_ROTOR_COUNT 1
+param set-default CA_ROTOR0_PX 0.3
+param set-default CA_SV_CS_COUNT 4
+param set-default CA_SV_CS0_TRQ_R -0.5
+param set-default CA_SV_CS1_TRQ_R 0.5
+param set-default CA_SV_CS1_TYPE 2
+param set-default CA_SV_CS2_TRQ_P 1.0
+param set-default CA_SV_CS2_TYPE 3
+param set-default CA_SV_CS3_TRQ_Y 1.0
+param set-default CA_SV_CS3_TYPE 4
+
 param set-default PWM_AUX_RATE 50
 param set-default PWM_MAIN_RATE 50

@@ -21,3 +21,16 @@
 #

 . ${R}etc/init.d/rc.mc_defaults
+
+param set-default CA_ROTOR_COUNT 4
+param set-default CA_ROTOR0_PX 0.15
+param set-default CA_ROTOR0_PY 0.15
+param set-default CA_ROTOR1_PX -0.15
+param set-default CA_ROTOR1_PY -0.15
+param set-default CA_ROTOR2_PX 0.15
+param set-default CA_ROTOR2_PY -0.15
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.15
+param set-default CA_ROTOR3_PY 0.15
+param set-default CA_ROTOR3_KM -0.05
+
@@ -1,39 +0,0 @@
-#!/bin/sh
-#
-# @name S500 with control allocation
-#
-# @type Quadrotor x
-# @class Copter
-#
-# @maintainer Silvan Fuhrer
-#
-# @board px4_fmu-v2 exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-set MIXER skip
-set MIXER_AUX none
-
-param set-default SYS_CTRL_ALLOC 1
-
-param set-default CA_AIRFRAME 0
-
-param set-default CA_ROTOR_COUNT 4
-param set-default CA_ROTOR0_PX 0.177
-param set-default CA_ROTOR0_PY 0.177
-param set-default CA_ROTOR0_KM 0.05
-param set-default CA_ROTOR1_PX -0.177
-param set-default CA_ROTOR1_PY -0.177
-param set-default CA_ROTOR1_KM 0.05
-param set-default CA_ROTOR2_PX 0.177
-param set-default CA_ROTOR2_PY -0.177
-param set-default CA_ROTOR2_KM -0.05
-param set-default CA_ROTOR3_PX -0.177
-param set-default CA_ROTOR3_PY 0.177
-param set-default CA_ROTOR3_KM -0.05
-
-param set-default PWM_MAIN_FUNC1 101
-param set-default PWM_MAIN_FUNC2 102
-param set-default PWM_MAIN_FUNC3 103
-param set-default PWM_MAIN_FUNC4 104
@@ -0,0 +1,23 @@
+#!/bin/sh
+#
+# @name Holybro X500 V2
+#
+# @type Quadrotor x
+# @class Copter
+#
+# @maintainer Farhang Naderi <farhang.nba@gmail.com>
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.mc_defaults
+
+param set-default IMU_GYRO_CUTOFF 30
+
+param set-default MC_ROLLRATE_P 0.14
+param set-default MC_PITCHRATE_P 0.14
+param set-default MC_ROLLRATE_I 0.3
+param set-default MC_PITCHRATE_I 0.3
+param set-default MC_ROLLRATE_D 0.004
+param set-default MC_PITCHRATE_D 0.004
@@ -46,7 +46,7 @@ param set-default COM_RC_LOSS_T 3


 # ekf2
-param set-default EKF2_AID_MASK 35
+param set-default EKF2_AID_MASK 33
 param set-default EKF2_BARO_DELAY 0
 param set-default EKF2_BARO_NOISE 2.0

@@ -147,7 +147,7 @@ param set-default MPC_Z_VEL_P 0.27


 # gimbal configuration
-param set-default MNT_MODE_IN 1
+param set-default MNT_MODE_IN 0
 param set-default MNT_MODE_OUT 1
 param set-default MNT_MAN_PITCH 2
 param set-default MNT_RC_IN_MODE 1
@@ -164,6 +164,8 @@ param set-default RC_MAP_AUX2       5
 param set-default RC_MAP_AUX3       10
 param set-default RC_MAP_AUX4       8
 param set-default RC_MAP_FLTMODE    6
+param set-default RC_MAP_RETURN_SW  7
+
 param set-default RC1_TRIM          1000


@@ -23,6 +23,23 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default CA_ROTOR_COUNT 6
+param set-default CA_ROTOR0_PX 0.0
+param set-default CA_ROTOR0_PY 0.5
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR1_PX 0.0
+param set-default CA_ROTOR1_PY -0.5
+param set-default CA_ROTOR2_PX 0.43
+param set-default CA_ROTOR2_PY -0.25
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX -0.43
+param set-default CA_ROTOR3_PY 0.25
+param set-default CA_ROTOR4_PX 0.43
+param set-default CA_ROTOR4_PY 0.25
+param set-default CA_ROTOR5_PX -0.43
+param set-default CA_ROTOR5_PY -0.25
+param set-default CA_ROTOR5_KM -0.05
+
 set MIXER hexa_x

 # Need to set all 8 channels
@@ -1,52 +0,0 @@
-#!/bin/sh
-#
-# @name Hex X with control allocation
-#
-# @type Hexarotor x
-# @class Copter
-#
-# @maintainer Silvan Fuhrer
-#
-# @board px4_fmu-v2 exclude
-#
-
-. ${R}etc/init.d/rc.mc_defaults
-
-param set-default SYS_CTRL_ALLOC 1
-
-param set-default CA_AIRFRAME 0
-param set-default CA_ROTOR_COUNT 6
-
-param set-default CA_ROTOR0_PX 0.0
-param set-default CA_ROTOR0_PY 0.275
-param set-default CA_ROTOR0_KM -0.05
-
-param set-default CA_ROTOR1_PX 0.0
-param set-default CA_ROTOR1_PY -0.275
-param set-default CA_ROTOR1_KM 0.05
-
-param set-default CA_ROTOR2_PX 0.238
-param set-default CA_ROTOR2_PY -0.1375
-param set-default CA_ROTOR2_KM -0.05
-
-param set-default CA_ROTOR3_PX -0.238
-param set-default CA_ROTOR3_PY 0.1375
-param set-default CA_ROTOR3_KM 0.05
-
-param set-default CA_ROTOR4_PX 0.238
-param set-default CA_ROTOR4_PY 0.1375
-param set-default CA_ROTOR4_KM 0.05
-
-param set-default CA_ROTOR5_PX -0.238
-param set-default CA_ROTOR5_PY -0.1375
-param set-default CA_ROTOR5_KM -0.05
-
-param set-default PWM_MAIN_FUNC1 101
-param set-default PWM_MAIN_FUNC2 102
-param set-default PWM_MAIN_FUNC3 103
-param set-default PWM_MAIN_FUNC4 104
-param set-default PWM_MAIN_FUNC5 105
-param set-default PWM_MAIN_FUNC6 106
-
-set MIXER skip
-set MIXER_AUX none
@@ -23,6 +23,23 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default CA_ROTOR_COUNT 6
+param set-default CA_ROTOR0_PX 0.5
+param set-default CA_ROTOR0_PY 0.0
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR1_PX -0.5
+param set-default CA_ROTOR1_PY 0.0
+param set-default CA_ROTOR2_PX -0.25
+param set-default CA_ROTOR2_PY -0.43
+param set-default CA_ROTOR2_KM -0.05
+param set-default CA_ROTOR3_PX 0.25
+param set-default CA_ROTOR3_PY 0.43
+param set-default CA_ROTOR4_PX 0.25
+param set-default CA_ROTOR4_PY -0.43
+param set-default CA_ROTOR5_PX -0.25
+param set-default CA_ROTOR5_PY 0.43
+param set-default CA_ROTOR5_KM -0.05
+
 set MIXER hexa_+

 # Need to set all 8 channels
@@ -25,6 +25,28 @@

 . ${R}etc/init.d/rc.mc_defaults

+param set-default CA_ROTOR_COUNT 8
+param set-default CA_ROTOR0_KM -0.05
+param set-default CA_ROTOR0_PX 0.46
+param set-default CA_ROTOR0_PY 0.19
+param set-default CA_ROTOR1_KM -0.05
+param set-default CA_ROTOR1_PX -0.46
+param set-default CA_ROTOR1_PY -0.19
+param set-default CA_ROTOR2_PX 0.19
+param set-default CA_ROTOR2_PY 0.46
+param set-default CA_ROTOR3_PX -0.46
+param set-default CA_ROTOR3_PY 0.19
+param set-default CA_ROTOR4_PX 0.46
+param set-default CA_ROTOR4_PY -0.19
+param set-default CA_ROTOR5_PX -0.19
+param set-default CA_ROTOR5_PY -0.46
+param set-default CA_ROTOR6_KM -0.05
+param set-default CA_ROTOR6_PX 0.19
+param set-default CA_ROTOR6_PY -0.46
+param set-default CA_ROTOR7_KM -0.05
+param set-default CA_ROTOR7_PX -0.19
+param set-default CA_ROTOR7_PY 0.46
+
 set MIXER octo_x

 set PWM_OUT 12345678
@@ -72,7 +72,7 @@ px4_add_romfs_files(
 	4015_holybro_s500
 	4016_holybro_px4vision
 	4017_nxp_hovergames
-	4018_s500_ctrlalloc
+	4019_x500_v2
 	4030_3dr_solo
 	4031_3dr_quad
 	4040_reaper
@@ -99,7 +99,6 @@ px4_add_romfs_files(
 	# [6000, 6999] Hexarotor x"
 	6001_hexa_x
 	6002_draco_r
-	6003_hexa_x_ctrlalloc

 	# [7000, 7999] Hexarotor +"
 	7001_hexa_+
@@ -7,7 +7,10 @@

 set VEHICLE_TYPE mc

-param set-default IMU_GYRO_RATEMAX 800
+if param compare IMU_GYRO_RATEMAX 400
+then
+	param set-default IMU_GYRO_RATEMAX 800
+fi

 param set-default NAV_ACC_RAD 2

@@ -130,6 +130,13 @@ then
 	fi
 fi

+# SHT3x temperature and hygrometer sensor, external I2C
+if param compare -s SENS_EN_SHT3X 1
+then
+	sht3x start -X
+	sht3x start -X -a 0x45
+fi
+
 # TE MS4525 differential pressure sensor external I2C
 if param compare -s SENS_EN_MS4525 1
 then
@@ -142,6 +149,19 @@ then
 	ms5525_airspeed start -X
 fi

+# IR-LOCK sensor external I2C
+if param compare -s SENS_EN_IRLOCK 1
+then
+	irlock start -X
+fi
+
+# PCF8583 counter (RPM sensor)
+if param compare -s SENS_EN_PCF8583 1
+then
+	pcf8583 start -X
+	pcf8583 start -X -a 0x51
+fi
+
 # probe for optional external I2C devices
 if param compare SENS_EXT_I2C_PRB 1
 then
@@ -486,11 +486,11 @@ else
 	. ${R}etc/init.d/rc.thermal_cal

 	#
-	# Start vmount to control mounts such as gimbals, disabled by default.
+	# Start gimbal to control mounts such as gimbals, disabled by default.
 	#
 	if param greater -s MNT_MODE_IN -1
 	then
-		vmount start
+		gimbal start
 	fi

 	# Check for flow sensor
@@ -35,7 +35,6 @@ do
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param set MAV_0_CONFIG 101' || true
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param set MAV_1_CONFIG 102' || true
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param set MAV_2_CONFIG 103' || true
-	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param set MAV_3_CONFIG 104' || true

 	# enable all GPS
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param set GPS_1_CONFIG 201' || true
@@ -48,6 +47,7 @@ do

 	${DIR}/reboot.py --device ${SERIAL_DEVICE}

+	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param status'
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param dump /fs/mtd_params' || true
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param dump /fs/microsd/parameters_backup.bson' || true

@@ -39,7 +39,7 @@ function spawn_model() {

 	echo "Spawning ${MODEL}_${N} at ${X} ${Y}"

-	gz model --spawn-file=/tmp/${MODEL}_${N}.sdf --model-name=${MODEL}_${N} -x ${X} -y ${Y} -z 0.0
+	gz model --spawn-file=/tmp/${MODEL}_${N}.sdf --model-name=${MODEL}_${N} -x ${X} -y ${Y} -z 0.83

 	popd &>/dev/null

@@ -150,7 +150,7 @@ simulator,CONFIG_MODULES_SIMULATOR=y
 temperature_compensation,CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 uuv_att_control,CONFIG_MODULES_UUV_ATT_CONTROL=y
 uuv_pos_control,CONFIG_MODULES_UUV_POS_CONTROL=y
-vmount,CONFIG_MODULES_VMOUNT=y
+gimbal,CONFIG_MODULES_GIMBAL=y
 vtol_att_control,CONFIG_MODULES_VTOL_ATT_CONTROL=y
 bl_update,CONFIG_SYSTEMCMDS_BL_UPDATE=y
 dmesg,CONFIG_SYSTEMCMDS_DMESG=y
@@ -142,7 +142,6 @@ def get_actuator_output(yaml_config, output_functions, timer_config_file, verbos
        }
    if 'show_subgroups_if' in actuator_output_yaml:
        actuator_output['show-subgroups-if'] = actuator_output_yaml['show_subgroups_if']
-    add_reverse_range_param = actuator_output_yaml.get('add_reverse_range_param', False)

    # config parameters
    def get_config_params(param_list):
@@ -257,14 +256,13 @@ def get_actuator_output(yaml_config, output_functions, timer_config_file, verbos
                per_channel_params.append(param)


-        if add_reverse_range_param:
-            param = {
-                    'label': 'Rev Range\n(for Servos)',
-                    'name': param_prefix+'_REV',
-                    'index-offset': -1,
-                    'show-as': 'bitset',
-                }
-            per_channel_params.append(param)
+        param = {
+                'label': 'Rev Range\n(for Servos)',
+                'name': param_prefix+'_REV',
+                'index-offset': -1,
+                'show-as': 'bitset',
+            }
+        per_channel_params.append(param)

        # TODO: support non-standard per-channel parameters

@@ -332,9 +330,11 @@ def get_mixers(yaml_config, output_functions, verbose):
        option = select_param + '==' + str(type_index)
        mixer_config = {
                'option': option,
+                'help-url': 'https://docs.px4.io/master/en/config/actuators.html',
            }
-        if 'type' in current_type:
-            mixer_config['type'] = current_type['type']
+        for optional in ['type', 'title']:
+            if optional in current_type:
+                mixer_config[optional] = current_type[optional]
        actuators = []
        for actuator_conf in current_type['actuators']:
            actuator = {
@@ -178,7 +178,6 @@ def get_actuator_output_params(yaml_config, output_functions,
    all_params = {}
    group_idx = 0

-    add_reverse_range_param = yaml_config['actuator_output'].get('add_reverse_range_param', False)
    all_param_prefixes = {}

    def add_local_param(param_name, param_def):
@@ -299,13 +298,9 @@ Note that non-motor outputs might already be active in prearm state if COM_PREAR
 '''
        minimum_description = \
 '''Minimum output value (when not disarmed).
-
-The output range can be reversed by setting Min > Max.
 '''
        maximum_description = \
 '''Maxmimum output value (when not disarmed).
-
-The output range can be reversed by setting Min > Max.
 '''
        failsafe_description = \
 '''This is the output value that is set when in failsafe mode.
@@ -346,29 +341,29 @@ When set to -1 (default), the value depends on the function (see {:}).
                    }
                add_local_param(param_prefix+'_'+param_suffix+'${i}', param)

-    if add_reverse_range_param:
-        for param_prefix in all_param_prefixes:
-            groups = all_param_prefixes[param_prefix]
-            # collect the bits
-            channel_bits = {}
-            for instance_start, instance_start_label, num_instances, label in groups:
-                for instance in range(instance_start, instance_start+num_instances):
-                    instance_label = instance - instance_start + instance_start_label
-                    channel_bits[instance-1] = label + ' ' + str(instance_label)
+    # add reverse range param
+    for param_prefix in all_param_prefixes:
+        groups = all_param_prefixes[param_prefix]
+        # collect the bits
+        channel_bits = {}
+        for instance_start, instance_start_label, num_instances, label in groups:
+            for instance in range(instance_start, instance_start+num_instances):
+                instance_label = instance - instance_start + instance_start_label
+                channel_bits[instance-1] = label + ' ' + str(instance_label)

-            param = {
-                'description': {
-                    'short': 'Reverse Output Range for '+module_name,
-                    'long':
+        param = {
+            'description': {
+                'short': 'Reverse Output Range for '+module_name,
+                'long':
 '''Allows to reverse the output range for each channel.
 Note: this is only useful for servos.
 '''.format(channel_label),
-                    },
-                'type': 'bitmask',
-                'default': 0,
-                'bit': channel_bits
-                }
-            add_local_param(param_prefix+'_REV', param)
+                },
+            'type': 'bitmask',
+            'default': 0,
+            'bit': channel_bits
+            }
+        add_local_param(param_prefix+'_REV', param)

    if verbose: print('adding actuator params: {:}'.format(all_params))
    return all_params
@@ -7,7 +7,8 @@ import os
 import math
 import matplotlib.pyplot as plt
 import numpy as np
-import scipy as sp
+
+from scipy.signal import medfilt

 from pyulog import *

@@ -65,7 +66,7 @@ def resampleWithDeltaX(x,y):
    return resampledX,resampledY

 def median_filter(data):
-    return sp.signal.medfilt(data, 31)
+    return medfilt(data, 31)

 parser = argparse.ArgumentParser(description='Reads in IMU data from a static thermal calibration test and performs a curve fit of gyro, accel and baro bias vs temperature')
 parser.add_argument('filename', metavar='file.ulg', help='ULog input file')
@@ -16,7 +16,7 @@ class ModuleDocumentation(object):
    valid_categories = ['driver', 'estimator', 'controller', 'system',
                        'communication', 'command', 'template', 'simulation', 'autotune']
    valid_subcategories = ['', 'distance_sensor', 'imu', 'airspeed_sensor',
-                           'magnetometer', 'baro', 'optical_flow']
+                           'magnetometer', 'baro', 'optical_flow', 'rpm_sensor']

    max_line_length = 80 # wrap lines that are longer than this

@@ -268,10 +268,14 @@ for serial_command in serial_commands:
                default_port_str = port_config['default'][i]
            else:
                default_port_str = port_config['default']
+
            if default_port_str != "":
                if default_port_str not in serial_ports:
                    raise Exception("Default Port {:} not found for {:}".format(default_port_str, serial_command['label']))
-                default_port = serial_ports[default_port_str]['index']
+
+                if default_port_str in dict(board_ports).keys():
+                    default_port = serial_ports[default_port_str]['index']
+

        commands.append({
            'command': serial_command['command'],
@@ -48,7 +48,6 @@ echo "Installing PX4 general dependencies"
 sudo pacman -Sy --noconfirm --needed \
 	astyle \
 	base-devel \
-	ccache \
 	clang \
 	cmake \
 	cppcheck \
@@ -77,7 +77,6 @@ sudo apt-get update -y --quiet
 sudo DEBIAN_FRONTEND=noninteractive apt-get -y --quiet --no-install-recommends install \
 	astyle \
 	build-essential \
-	ccache \
 	cmake \
 	cppcheck \
 	file \
@@ -101,12 +100,6 @@ sudo DEBIAN_FRONTEND=noninteractive apt-get -y --quiet --no-install-recommends i
 	zip \
 	;

-if [[ "${UBUNTU_RELEASE}" == "16.04" ]]; then
-	echo "Installing Ubuntu 16.04 PX4-compatible ccache version"
-	wget -O /tmp/ccache_3.4.1-1_amd64.deb http://launchpadlibrarian.net/356662933/ccache_3.4.1-1_amd64.deb
-	sudo dpkg -i /tmp/ccache_3.4.1-1_amd64.deb
-fi
-
 # Python3 dependencies
 echo
 echo "Installing PX4 Python3 dependencies"
@@ -192,7 +192,7 @@ elif [ "$program" == "ignition" ] && [ -z "$no_sim" ]; then
 		ignition_headless=""
 	fi
 	source "$src_path/Tools/setup_ignition.bash" "${src_path}" "${build_path}"
-	ign gazebo ${verbose} ${ignition_headless} -r "${src_path}/Tools/simulation-ignition/worlds/${model}.world"&
+	ign gazebo --force-version 5 ${verbose} ${ignition_headless} -r "${src_path}/Tools/simulation-ignition/worlds/${model}.world"&
 elif [ "$program" == "flightgear" ] && [ -z "$no_sim" ]; then
 	echo "FG setup"
 	cd "${src_path}/Tools/flightgear_bridge/"
@@ -56,6 +56,21 @@ def get_N_colors(N, s=0.8, v=0.9):
        hex_out.append("#"+"".join(map(lambda x: format(x, '02x'), rgb)))
    return hex_out

+def topic_filename(topic):
+    MSG_PATH = 'msg/'
+
+    file_list = os.listdir(MSG_PATH)
+    msg_files = [file.replace('.msg', '') for file in file_list if file.endswith(".msg")]
+
+    if topic in msg_files:
+        return topic
+    else:
+        for msg_file in msg_files:
+            with open(f'{MSG_PATH}/{msg_file}.msg') as f:
+                ret = re.findall(f'^# TOPICS.*{topic}.*',f.read(),re.MULTILINE)
+                if len(ret) > 0:
+                    return msg_file
+    return "no_file"

 class PubSub(object):
    """ Collects either publication or subscription information for nodes
@@ -679,8 +694,7 @@ class OutputJSON(object):
            node['type'] = 'topic'
            node['color'] = topic_colors[topic]
            # url is opened when double-clicking on the node
-            # TODO: does not work for multi-topics
-            node['url'] = 'https://github.com/PX4/PX4-Autopilot/blob/master/msg/'+topic+'.msg'
+            node['url'] = 'https://github.com/PX4/PX4-Autopilot/blob/master/msg/'+topic_filename(topic)+'.msg'
            nodes.append(node)

        data['nodes'] = nodes
@@ -74,7 +74,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -61,6 +61,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -63,6 +63,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -63,6 +63,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -31,7 +31,7 @@ CONFIG_MODULES_NAVIGATOR=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIH=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
 CONFIG_SYSTEMCMDS_DMESG=y
@@ -71,7 +71,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -56,7 +56,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_DYN=y
 CONFIG_SYSTEMCMDS_LED_CONTROL=y
@@ -17,7 +17,6 @@ CONFIG_MODULES_DATAMAN=y
 CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_EVENTS=y
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
-CONFIG_MODULES_GYRO_FFT=y
 CONFIG_MODULES_LAND_DETECTOR=y
 CONFIG_MODULES_LOAD_MON=y
 CONFIG_MODULES_LOGGER=y
@@ -61,6 +61,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -76,7 +76,7 @@ CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -77,7 +77,7 @@ CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -72,7 +72,7 @@ CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -0,0 +1,245 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_MMCSD_HAVE_CARDDETECT is not set
+# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
+# CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_MMCSD_SPI is not set
+# CONFIG_NET_CAN_CANFD is not set
+# CONFIG_NET_ETHERNET is not set
+# CONFIG_NET_IPv4 is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_MKFATFS is not set
+# CONFIG_NSH_DISABLE_REBOOT is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_SHUTDOWN is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/cubepilot/cubeorange/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743ZI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_DCACHE=y
+CONFIG_ARMV7M_DTCM=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_ARM_MPU_EARLY_RESET=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_CRASHDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=79954
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BUILTIN=y
+CONFIG_C99_BOOL8=y
+CONFIG_CANUTILS_CANDUMP=y
+CONFIG_CANUTILS_CANSEND=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x1016
+CONFIG_CDCACM_PRODUCTSTR="CubeOrange"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x2DAE
+CONFIG_CDCACM_VENDORSTR="CubePilot"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
+CONFIG_DEV_PIPE_SIZE=70
+CONFIG_EXAMPLES_CALIB_UDELAY=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FAT_DMAMEMORY=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_LFN_ALIAS_HASH=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_BINFS=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FATTIME=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
+CONFIG_FS_PROCFS_MAX_TASKS=64
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MMCSD=y
+CONFIG_MMCSD_SDIO=y
+CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y
+CONFIG_MM_REGIONS=4
+CONFIG_MTD=y
+CONFIG_MTD_BYTE_WRITE=y
+CONFIG_MTD_PARTITION=y
+CONFIG_MTD_PROGMEM=y
+CONFIG_MTD_RAMTRON=y
+CONFIG_NAME_MAX=40
+CONFIG_NET=y
+CONFIG_NETDEV_CAN_BITRATE_IOCTL=y
+CONFIG_NETDEV_IFINDEX=y
+CONFIG_NETDEV_PHY_IOCTL=y
+CONFIG_NET_CAN=y
+CONFIG_NET_CAN_RAW_TX_DEADLINE=y
+CONFIG_NET_CAN_SOCK_OPTS=y
+CONFIG_NET_TIMESTAMP=y
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_DISABLE_TELNETD=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_STRERROR=y
+CONFIG_NSH_VARS=y
+CONFIG_OTG_ID_GPIO_DISABLE=y
+CONFIG_PIPES=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAMTRON_SETSPEED=y
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_READLINE_CMD_HISTORY=y
+CONFIG_READLINE_TABCOMPLETION=y
+CONFIG_RTC_DATETIME=y
+CONFIG_SCHED_ATEXIT=y
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_LPWORKPRIORITY=50
+CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_WAITPID=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SDMMC1_SDIO_PULLUP=y
+CONFIG_SEM_NNESTPRIO=8
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STM32H7_ADC1=y
+CONFIG_STM32H7_ADC3=y
+CONFIG_STM32H7_BBSRAM=y
+CONFIG_STM32H7_BBSRAM_FILES=5
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_DMACAPABLE=y
+CONFIG_STM32H7_FDCAN1=y
+CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
+CONFIG_STM32H7_I2C1=y
+CONFIG_STM32H7_I2C2=y
+CONFIG_STM32H7_I2C_DYNTIMEO=y
+CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_RTC=y
+CONFIG_STM32H7_RTC_HSECLOCK=y
+CONFIG_STM32H7_RTC_MAGIC_REG=1
+CONFIG_STM32H7_SAVE_CRASHDUMP=y
+CONFIG_STM32H7_SDMMC1=y
+CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_SPI1=y
+CONFIG_STM32H7_SPI1_DMA=y
+CONFIG_STM32H7_SPI1_DMA_BUFFER=1024
+CONFIG_STM32H7_SPI2=y
+CONFIG_STM32H7_SPI4=y
+CONFIG_STM32H7_SPI4_DMA=y
+CONFIG_STM32H7_SPI4_DMA_BUFFER=1024
+CONFIG_STM32H7_SPI_DMA=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_TIM3=y
+CONFIG_STM32H7_TIM4=y
+CONFIG_STM32H7_UART4=y
+CONFIG_STM32H7_UART7=y
+CONFIG_STM32H7_UART8=y
+CONFIG_STM32H7_USART2=y
+CONFIG_STM32H7_USART3=y
+CONFIG_STM32H7_USART6=y
+CONFIG_STM32H7_USART_BREAKS=y
+CONFIG_STM32H7_USART_INVERT=y
+CONFIG_STM32H7_USART_SINGLEWIRE=y
+CONFIG_STM32H7_USART_SWAP=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGTSTP=y
+CONFIG_UART4_BAUD=57600
+CONFIG_UART4_RXBUFSIZE=600
+CONFIG_UART4_TXBUFSIZE=1500
+CONFIG_UART7_BAUD=57600
+CONFIG_UART7_RXBUFSIZE=600
+CONFIG_UART7_SERIAL_CONSOLE=y
+CONFIG_UART7_TXBUFSIZE=1500
+CONFIG_UART8_BAUD=57600
+CONFIG_UART8_RXBUFSIZE=600
+CONFIG_UART8_TXBUFSIZE=1500
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_IFLOWCONTROL=y
+CONFIG_USART2_OFLOWCONTROL=y
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_TXBUFSIZE=1500
+CONFIG_USART3_BAUD=57600
+CONFIG_USART3_IFLOWCONTROL=y
+CONFIG_USART3_OFLOWCONTROL=y
+CONFIG_USART3_RXBUFSIZE=600
+CONFIG_USART3_TXBUFSIZE=3000
+CONFIG_USART6_BAUD=57600
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_USERMAIN_STACKSIZE=2944
+CONFIG_USER_ENTRYPOINT="nsh_main"
+CONFIG_WATCHDOG=y
@@ -0,0 +1,22 @@
+CONFIG_DRIVERS_ADC_ADS1115=n
+CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=n
+CONFIG_DRIVERS_IRLOCK=n
+CONFIG_DRIVERS_PCA9685=n
+CONFIG_DRIVERS_PCA9685_PWM_OUT=n
+CONFIG_DRIVERS_RPM=n
+CONFIG_DRIVERS_UAVCAN=n
+CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=n
+CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=n
+CONFIG_MODULES_ROVER_POS_CONTROL=n
+CONFIG_MODULES_TEMPERATURE_COMPENSATION=n
+CONFIG_DRIVERS_UAVCAN_V1=y
+CONFIG_UAVCAN_V1_BMS_SUBSCRIBER=y
+CONFIG_UAVCAN_V1_ESC_CONTROLLER=y
+CONFIG_UAVCAN_V1_ESC_SUBSCRIBER=y
+CONFIG_UAVCAN_V1_GNSS_PUBLISHER=y
+CONFIG_UAVCAN_V1_GNSS_SUBSCRIBER_0=y
+CONFIG_UAVCAN_V1_GNSS_SUBSCRIBER_1=y
+CONFIG_UAVCAN_V1_READINESS_PUBLISHER=y
+CONFIG_UAVCAN_V1_UORB_ACTUATOR_OUTPUTS_PUBLISHER=y
+CONFIG_UAVCAN_V1_UORB_SENSOR_GPS_PUBLISHER=y
+CONFIG_UAVCAN_V1_UORB_SENSOR_GPS_SUBSCRIBER=y
@@ -149,7 +149,6 @@
 #define BOARD_HAS_STATIC_MANIFEST 1


-#define BOARD_DSHOT_MOTOR_ASSIGNMENT {3, 2, 1, 0, 4, 5};

 #define BOARD_ENABLE_CONSOLE_BUFFER

@@ -74,7 +74,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -144,7 +144,6 @@
 #define BOARD_HAS_STATIC_MANIFEST 1


-#define BOARD_DSHOT_MOTOR_ASSIGNMENT {3, 2, 1, 0, 4, 5};

 #define BOARD_ENABLE_CONSOLE_BUFFER

@@ -58,7 +58,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_DYN=y
 CONFIG_SYSTEMCMDS_LED_CONTROL=y
@@ -62,6 +62,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -68,6 +68,5 @@ else()
 			nuttx_arch
 			nuttx_drivers
 			px4_layer
-			arch_io_pins
 	)
 endif()
@@ -69,7 +69,7 @@ CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -181,7 +181,6 @@

 #define BOARD_NUM_IO_TIMERS 4

-#define BOARD_DSHOT_MOTOR_ASSIGNMENT {3, 2, 1, 0, 4, 5, 6, 7, 9, 8};

 /* Power supply control and monitoring GPIOs */

@@ -15,20 +15,17 @@ CONFIG_DRIVERS_OSD=y
 CONFIG_DRIVERS_PWM_OUT=y
 CONFIG_DRIVERS_RC_INPUT=y
 CONFIG_DRIVERS_TELEMETRY_FRSKY_TELEMETRY=y
-CONFIG_DRIVERS_TONE_ALARM=y
 CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
-CONFIG_MODULES_EVENTS=y
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
 CONFIG_MODULES_LAND_DETECTOR=y
 CONFIG_MODULES_LOGGER=y
 CONFIG_MODULES_MANUAL_CONTROL=y
 CONFIG_MODULES_MAVLINK=y
 CONFIG_MODULES_MC_ATT_CONTROL=y
-CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
 CONFIG_MODULES_MC_POS_CONTROL=y
 CONFIG_MODULES_MC_RATE_CONTROL=y
 CONFIG_MODULES_NAVIGATOR=y
@@ -90,6 +90,7 @@ CONFIG_IDLETHREAD_STACKSIZE=750
 CONFIG_LIBC_FLOATINGPOINT=y
 CONFIG_LIBC_LONG_LONG=y
 CONFIG_LIBC_STRERROR=y
+CONFIG_LIBC_STRERROR_SHORT=y
 CONFIG_MEMSET_64BIT=y
 CONFIG_MEMSET_OPTSPEED=y
 CONFIG_MMCSD=y
@@ -0,0 +1,3 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ROMFSROOT=""
@@ -0,0 +1,92 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS0"
+CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
+CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_COMMON_BAROMETERS=y
+CONFIG_DRIVERS_BATT_SMBUS=y
+CONFIG_DRIVERS_CAMERA_CAPTURE=y
+CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20689=y
+CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
+CONFIG_DRIVERS_OSD=y
+CONFIG_COMMON_LIGHT=y
+CONFIG_COMMON_MAGNETOMETER=y
+CONFIG_COMMON_OPTICAL_FLOW=y
+CONFIG_DRIVERS_POWER_MONITOR_INA226=y
+CONFIG_DRIVERS_PWM_OUT=y
+CONFIG_DRIVERS_PWM_OUT_SIM=y
+CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_DRIVERS_ROBOCLAW=y
+CONFIG_DRIVERS_RPM=y
+CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
+CONFIG_COMMON_TELEMETRY=y
+CONFIG_DRIVERS_TONE_ALARM=y
+CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
+CONFIG_MODULES_AIRSPEED_SELECTOR=y
+CONFIG_MODULES_BATTERY_STATUS=y
+CONFIG_MODULES_CAMERA_FEEDBACK=y
+CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
+CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_ESC_BATTERY=y
+CONFIG_MODULES_EVENTS=y
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_FW_ATT_CONTROL=y
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_GYRO_FFT=y
+CONFIG_MODULES_LAND_DETECTOR=y
+CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+CONFIG_MODULES_LOAD_MON=y
+CONFIG_MODULES_LOGGER=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_MANUAL_CONTROL=y
+CONFIG_MODULES_MAVLINK=y
+CONFIG_MODULES_MC_ATT_CONTROL=y
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+CONFIG_MODULES_MC_POS_CONTROL=y
+CONFIG_MODULES_MC_RATE_CONTROL=y
+CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODULES_RC_UPDATE=y
+CONFIG_MODULES_ROVER_POS_CONTROL=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_MODULES_SIH=y
+CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
+CONFIG_MODULES_GIMBAL=y
+CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_DUMPFILE=y
+CONFIG_SYSTEMCMDS_GPIO=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_LED_CONTROL=y
+CONFIG_SYSTEMCMDS_MFT=y
+CONFIG_SYSTEMCMDS_MIXER=y
+CONFIG_SYSTEMCMDS_MOTOR_TEST=y
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_PWM=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SD_BENCH=y
+CONFIG_SYSTEMCMDS_SD_STRESS=y
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y
@@ -0,0 +1,13 @@
+{
+    "board_id": 1048,
+    "magic": "PX4FWv1",
+    "description": "Firmware for the KakuteH7 board",
+    "image": "",
+    "build_time": 0,
+    "summary": "KAKUTEH7",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 1835008,
+    "git_identity": "",
+    "board_revision": 0
+}
@@ -0,0 +1,27 @@
+#!/bin/sh
+#
+# board specific defaults
+#------------------------------------------------------------------------------
+
+param set-default BAT1_V_DIV 11.2
+param set-default BAT1_A_PER_V 59.5
+
+# system_power unavailable
+param set-default CBRK_SUPPLY_CHK 894281
+
+# Select the Generic 250 Racer by default
+param set-default SYS_AUTOSTART 4050
+
+# use the Q attitude estimator, it works w/o mag or GPS.
+param set-default SYS_MC_EST_GROUP 3
+param set-default ATT_ACC_COMP 0
+param set-default ATT_W_ACC 0.4000
+param set-default ATT_W_GYRO_BIAS 0.0000
+
+param set-default SYS_HAS_MAG 0
+
+# the startup tune is not great on a binary output buzzer, so disable it
+param set-default CBRK_BUZZER 782090
+
+param set-default IMU_GYRO_RATEMAX 2000
+
@@ -0,0 +1,13 @@
+#!/bin/sh
+#
+# KakuteH7 specific board extras init
+#------------------------------------------------------------------------------
+
+if ! param compare OSD_ATXXXX_CFG 0
+then
+	atxxxx start -s
+fi
+
+# DShot telemetry is always on UART7
+dshot telemetry /dev/ttyS5
+
@@ -0,0 +1,13 @@
+#!/bin/sh
+#
+# Holybro KakuteH7 specific board sensors init
+#------------------------------------------------------------------------------
+board_adc start
+
+# The default IMU is an ICM20689, but there might also be an MPU6000
+if ! mpu6000 -R 6 -s start
+then
+	icm20689 -R 6 -s start
+fi
+
+bmp280 -X start
@@ -0,0 +1,93 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DEV_CONSOLE is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_SPI_EXCHANGE is not set
+# CONFIG_STM32H7_SYSCFG is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/holybro/kakuteh7/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743VI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_INITTHREAD_PRIORITY=254
+CONFIG_BOARD_LATE_INITIALIZE=y
+CONFIG_BOARD_LOOPSPERMSEC=22114
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_C99_BOOL8=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x004b
+CONFIG_CDCACM_PRODUCTSTR="PX4 BL Holybro KakuteH7"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x3162
+CONFIG_CDCACM_VENDORSTR="Holybro"
+CONFIG_CLOCK_MONOTONIC=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_PTHREAD=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FDCLONE_DISABLE=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_LIB_BOARDCTL=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SPI=y
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=32
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_USART3=y
+CONFIG_SYSTEMTICK_HOOK=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGINT_CHAR=0x03
+CONFIG_TTY_SIGTSTP=y
+CONFIG_USART3_RXBUFSIZE=600
+CONFIG_USART3_TXBUFSIZE=300
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_USERMAIN_STACKSIZE=2944
+CONFIG_USER_ENTRYPOINT="bootloader_main"
@@ -0,0 +1,419 @@
+/************************************************************************************
+ *
+ *   Copyright (C) 2016-2019 Gregory Nutt. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+#pragma once
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include "board_dma_map.h"
+
+#include <nuttx/config.h>
+
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+
+#include "stm32_rcc.h"
+#include "stm32_sdmmc.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+/* The holybro KakuteH7  board provides the following clock sources:
+ *
+ *   X1: 8 MHz crystal for HSE
+ *
+ * So we have these clock source available within the STM32
+ *
+ *   HSI: 16 MHz RC factory-trimmed
+ *   HSE:  8 MHz crystal for HSE
+ */
+
+#define STM32_BOARD_XTAL        8000000ul
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+#define STM32_LSE_FREQUENCY     32768
+
+/* Main PLL Configuration.
+ *
+ * PLL source is HSE = 8,000,000
+ *
+ * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
+ * Subject to:
+ *
+ *     1 <= PLLM <= 63
+ *     4 <= PLLN <= 512
+ *   150 MHz <= PLL_VCOL <= 420MHz
+ *   192 MHz <= PLL_VCOH <= 836MHz
+ *
+ * SYSCLK  = PLL_VCO / PLLP
+ * CPUCLK  = SYSCLK / D1CPRE
+ * Subject to
+ *
+ *   PLLP1   = {2, 4, 6, 8, ..., 128}
+ *   PLLP2,3 = {2, 3, 4, ..., 128}
+ *   CPUCLK <= 480 MHz
+ */
+
+#define STM32_BOARD_USEHSE
+
+#define STM32_PLLCFG_PLLSRC      RCC_PLLCKSELR_PLLSRC_HSE
+
+/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR
+ *
+ *   PLL1_VCO = (8,000,000 / 1) * 120 = 960 MHz
+ *
+ *   PLL1P = PLL1_VCO/2  = 960 MHz / 2   = 480 MHz
+ *   PLL1Q = PLL1_VCO/4  = 960 MHz / 4   = 240 MHz
+ *   PLL1R = PLL1_VCO/8  = 960 MHz / 8   = 120 MHz
+ */
+
+#define STM32_PLLCFG_PLL1CFG    (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVP1EN | \
+				 RCC_PLLCFGR_DIVQ1EN | \
+				 RCC_PLLCFGR_DIVR1EN)
+#define STM32_PLLCFG_PLL1M       RCC_PLLCKSELR_DIVM1(1)
+#define STM32_PLLCFG_PLL1N       RCC_PLL1DIVR_N1(120)
+#define STM32_PLLCFG_PLL1P       RCC_PLL1DIVR_P1(2)
+#define STM32_PLLCFG_PLL1Q       RCC_PLL1DIVR_Q1(4)
+#define STM32_PLLCFG_PLL1R       RCC_PLL1DIVR_R1(8)
+
+#define STM32_VCO1_FREQUENCY     ((STM32_HSE_FREQUENCY / 1) * 120)
+#define STM32_PLL1P_FREQUENCY    (STM32_VCO1_FREQUENCY / 2)
+#define STM32_PLL1Q_FREQUENCY    (STM32_VCO1_FREQUENCY / 4)
+#define STM32_PLL1R_FREQUENCY    (STM32_VCO1_FREQUENCY / 8)
+
+/* PLL2 */
+
+#define STM32_PLLCFG_PLL2CFG     (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \
+				  RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \
+				  RCC_PLLCFGR_DIVP2EN | \
+				  RCC_PLLCFGR_DIVQ2EN | \
+				  RCC_PLLCFGR_DIVR2EN)
+#define STM32_PLLCFG_PLL2M       RCC_PLLCKSELR_DIVM2(2)
+#define STM32_PLLCFG_PLL2N       RCC_PLL2DIVR_N2(48)
+#define STM32_PLLCFG_PLL2P       RCC_PLL2DIVR_P2(2)
+#define STM32_PLLCFG_PLL2Q       RCC_PLL2DIVR_Q2(2)
+#define STM32_PLLCFG_PLL2R       RCC_PLL2DIVR_R2(2)
+
+#define STM32_VCO2_FREQUENCY     ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL2P_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2Q_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2R_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+
+/* PLL3 */
+
+#define STM32_PLLCFG_PLL3CFG    (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVQ3EN)
+#define STM32_PLLCFG_PLL3M      RCC_PLLCKSELR_DIVM3(2)
+#define STM32_PLLCFG_PLL3N      RCC_PLL3DIVR_N3(48)
+#define STM32_PLLCFG_PLL3P      RCC_PLL3DIVR_P3(2)
+#define STM32_PLLCFG_PLL3Q      RCC_PLL3DIVR_Q3(4)
+#define STM32_PLLCFG_PLL3R      RCC_PLL3DIVR_R3(2)
+
+#define STM32_VCO3_FREQUENCY    ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL3P_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+#define STM32_PLL3Q_FREQUENCY   (STM32_VCO3_FREQUENCY / 4)
+#define STM32_PLL3R_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+
+/* SYSCLK = PLL1P = 480MHz
+ * CPUCLK = SYSCLK / 1 = 480 MHz
+ */
+
+#define STM32_RCC_D1CFGR_D1CPRE  (RCC_D1CFGR_D1CPRE_SYSCLK)
+#define STM32_SYSCLK_FREQUENCY   (STM32_PLL1P_FREQUENCY)
+#define STM32_CPUCLK_FREQUENCY   (STM32_SYSCLK_FREQUENCY / 1)
+
+/* Configure Clock Assignments */
+
+/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max)
+ * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 240
+ */
+
+#define STM32_RCC_D1CFGR_HPRE   RCC_D1CFGR_HPRE_SYSCLKd2        /* HCLK  = SYSCLK / 2 */
+#define STM32_ACLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* ACLK in D1, HCLK3 in D1 */
+#define STM32_HCLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* HCLK in D2, HCLK4 in D3 */
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY            /* same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE1  RCC_D2CFGR_D2PPRE1_HCLKd2       /* PCLK1 = HCLK / 2 */
+#define STM32_PCLK1_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB2 clock (PCLK2) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE2  RCC_D2CFGR_D2PPRE2_HCLKd2       /* PCLK2 = HCLK / 2 */
+#define STM32_PCLK2_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB3 clock (PCLK3) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D1CFGR_D1PPRE   RCC_D1CFGR_D1PPRE_HCLKd2        /* PCLK3 = HCLK / 2 */
+#define STM32_PCLK3_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB4 clock (PCLK4) is HCLK/4 (120 MHz) */
+
+#define STM32_RCC_D3CFGR_D3PPRE   RCC_D3CFGR_D3PPRE_HCLKd2       /* PCLK4 = HCLK / 2 */
+#define STM32_PCLK4_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* Timer clock frequencies */
+
+/* Timers driven from APB1 will be twice PCLK1 */
+
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* Timers driven from APB2 will be twice PCLK2 */
+
+#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM15_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM16_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM17_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+
+/* Kernel Clock Configuration
+ *
+ * Note: look at Table 54 in ST Manual
+ */
+
+/* I2C123 clock source */
+
+#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI
+
+/* I2C4 clock source */
+
+#define STM32_RCC_D3CCIPR_I2C4SRC    RCC_D3CCIPR_I2C4SEL_HSI
+
+/* SPI123 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2
+
+/* SPI45 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI45SRC  RCC_D2CCIP1R_SPI45SEL_PLL2
+
+/* SPI6 clock source */
+
+#define STM32_RCC_D3CCIPR_SPI6SRC    RCC_D3CCIPR_SPI6SEL_PLL2
+
+/* USB 1 and 2 clock source */
+
+#define STM32_RCC_D2CCIP2R_USBSRC    RCC_D2CCIP2R_USBSEL_PLL3
+
+/* ADC 1 2 3 clock source */
+
+#define STM32_RCC_D3CCIPR_ADCSEL     RCC_D3CCIPR_ADCSEL_PLL2
+
+/* FDCAN 1 2 clock source */
+
+#define STM32_RCC_D2CCIP1R_FDCANSEL  RCC_D2CCIP1R_FDCANSEL_HSE   /* FDCAN 1 2 clock source */
+
+#define STM32_FDCANCLK               STM32_HSE_FREQUENCY
+
+/* FLASH wait states
+ *
+ *  ------------ ---------- -----------
+ *  Vcore        MAX ACLK   WAIT STATES
+ *  ------------ ---------- -----------
+ *  1.15-1.26 V     70 MHz    0
+ *  (VOS1 level)   140 MHz    1
+ *                 210 MHz    2
+ *  1.05-1.15 V     55 MHz    0
+ *  (VOS2 level)   110 MHz    1
+ *                 165 MHz    2
+ *                 220 MHz    3
+ *  0.95-1.05 V     45 MHz    0
+ *  (VOS3 level)    90 MHz    1
+ *                 135 MHz    2
+ *                 180 MHz    3
+ *                 225 MHz    4
+ *  ------------ ---------- -----------
+ */
+
+#define BOARD_FLASH_WAITSTATES 2
+
+/* SDMMC definitions ********************************************************/
+
+/* Init 400kHz, freq = PLL1Q/(2*div)  div =  PLL1Q/(2*freq) */
+
+#define STM32_SDMMC_INIT_CLKDIV     (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+
+/* 25 MHz Max for now, 25 mHZ = PLL1Q/(2*div), div =  PLL1Q/(2*freq)
+ * div = 4.8 = 240 / 50, So round up to 5 for default speed 24 MB/s
+ */
+
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_SDXFR_CLKDIV    (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_SDXFR_CLKDIV    (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+
+#define STM32_SDMMC_CLKCR_EDGE      STM32_SDMMC_CLKCR_NEGEDGE
+
+/* LED definitions ******************************************************************/
+/* The holybro KakuteH7 board has three, LED_GREEN a Green LED, LED_BLUE
+ * a Blue LED and LED_RED a Red LED, that can be controlled by software.
+ *
+ * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
+ * The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with board_userled() */
+
+#define BOARD_LED1        0
+#define BOARD_NLEDS       1
+
+#define BOARD_LED_RED     BOARD_LED1
+
+/* LED bits for use with board_userled_all() */
+
+#define BOARD_LED1_BIT    (1 << BOARD_LED1)
+
+/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
+ * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
+ * events as follows:
+ *
+ *
+ *   SYMBOL                     Meaning                      LED state
+ *                                                        Red   Green Blue
+ *   ----------------------  --------------------------  ------ ------ ----*/
+
+#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
+#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
+#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
+#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
+#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
+#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
+#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
+#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
+#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */
+
+/* Thus if the Green LED is statically on, NuttX has successfully booted and
+ * is, apparently, running normally.  If the Red LED is flashing at
+ * approximately 2Hz, then a fatal error has been detected and the system
+ * has halted.
+ */
+
+/* Alternate function pin selections ************************************************/
+
+
+#define GPIO_USART1_RX   GPIO_USART1_RX_2    /* PA10 */
+#define GPIO_USART1_TX   GPIO_USART1_TX_2    /* PA9 */
+
+#define GPIO_USART2_RX   GPIO_USART2_RX_2   /* PD6 */
+#define GPIO_USART2_TX   GPIO_USART2_TX_2   /* PD5 */
+
+#define GPIO_USART3_RX   GPIO_USART3_RX_3   /* PD9  */
+#define GPIO_USART3_TX   GPIO_USART3_TX_3   /* PD8  */
+
+#define GPIO_UART4_RX    GPIO_UART4_RX_5    /* PD0 */
+#define GPIO_UART4_TX    GPIO_UART4_TX_5    /* PD1 */
+
+#define GPIO_USART6_RX   GPIO_USART6_RX_1   /* PC7  */
+#define GPIO_USART6_TX   GPIO_USART6_TX_1   /* PC6 */
+
+#define GPIO_UART7_RX    GPIO_UART7_RX_3    /* PE7 */
+#define GPIO_UART7_TX    GPIO_UART7_TX_3    /* PE8 */
+
+/* SPI
+ * SPI1 SD Card
+ * SPI2 is OSD AT7456E
+ * SPI4 is IMU
+ */
+
+#define GPIO_SPI1_MISO   GPIO_SPI1_MISO_1   /* PA6 */
+#define GPIO_SPI1_MOSI   GPIO_SPI1_MOSI_1   /* PA7 */
+#define GPIO_SPI1_SCK    GPIO_SPI1_SCK_1    /* PA5 */
+
+#define GPIO_SPI2_MISO   GPIO_SPI2_MISO_1   /* PB14 */
+#define GPIO_SPI2_MOSI   GPIO_SPI2_MOSI_1   /* PB15 */
+#define GPIO_SPI2_SCK    GPIO_SPI2_SCK_4    /* PB13 */
+
+#define GPIO_SPI4_MISO   GPIO_SPI4_MISO_2   /* PE5 */
+#define GPIO_SPI4_MOSI   GPIO_SPI4_MOSI_2   /* PE6 */
+#define GPIO_SPI4_SCK    GPIO_SPI4_SCK_2    /* PE2 */
+
+/* I2C
+ */
+
+#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1       /* PB6  */
+#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1       /* PB7  */
+
+#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
+#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
+
+/* SDMMC1
+ *
+ *      VDD 3.3
+ *      GND
+ *      SDMMC1_CK                           PC12
+ *      SDMMC1_CMD                          PD2
+ *      SDMMC1_D0                           PC8
+ *      SDMMC1_D1                           PC9
+ *      SDMMC1_D2                           PC10
+ *      SDMMC1_D3                           PC11
+ *      GPIO_SDMMC1_NCD                     PG0
+ */
+
+/* USB
+ *
+ *      OTG_FS_DM                           PA11
+ *      OTG_FS_DP                           PA12
+ *      VBUS                                PA9
+ */
+
+
+/* Board provides GPIO or other Hardware for signaling to timing analyzer */
+
+# define PROBE_INIT(mask)
+# define PROBE(n,s)
+# define PROBE_MARK(n)
+
@@ -0,0 +1,40 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2020 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+#define DMAMAP_SPI4_RX    DMAMAP_DMA12_SPI4RX_1 /* DMA2 */
+#define DMAMAP_SPI4_TX    DMAMAP_DMA12_SPI4TX_1 /* DMA2 */
+
+#define DMAMAP_USART2_RX   DMAMAP_DMA12_USART2RX_1 /* DMA2 */
+
@@ -0,0 +1,224 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_MMCSD_HAVE_CARDDETECT is not set
+# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
+# CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_MKFATFS is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+# CONFIG_SPI_CALLBACK is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/holybro/kakuteh7/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743II=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_DCACHE=y
+CONFIG_ARMV7M_DTCM=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_ARM_MPU_EARLY_RESET=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_CRASHDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=95150
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BUILTIN=y
+CONFIG_C99_BOOL8=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x004b
+CONFIG_CDCACM_PRODUCTSTR="PX4 KakuteH7"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x3162
+CONFIG_CDCACM_VENDORSTR="Holybro"
+CONFIG_CLOCK_MONOTONIC=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_MEMFAULT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
+CONFIG_DEV_PIPE_SIZE=70
+CONFIG_EXPERIMENTAL=y
+CONFIG_FAT_DMAMEMORY=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_LFN_ALIAS_HASH=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_BINFS=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FATTIME=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
+CONFIG_FS_PROCFS_MAX_TASKS=64
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MMCSD=y
+CONFIG_MMCSD_SDIO=y
+CONFIG_MM_REGIONS=4
+CONFIG_MTD=y
+CONFIG_MTD_BYTE_WRITE=y
+CONFIG_MTD_PARTITION=y
+CONFIG_MTD_PROGMEM=y
+CONFIG_MTD_RAMTRON=y
+CONFIG_NAME_MAX=40
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_DISABLE_IFCONFIG=y
+CONFIG_NSH_DISABLE_IFUPDOWN=y
+CONFIG_NSH_DISABLE_TELNETD=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_MMCSDSPIPORTNO=1
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_STRERROR=y
+CONFIG_NSH_VARS=y
+CONFIG_OTG_ID_GPIO_DISABLE=y
+CONFIG_PIPES=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAMTRON_SETSPEED=y
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_READLINE_CMD_HISTORY=y
+CONFIG_READLINE_TABCOMPLETION=y
+CONFIG_RTC_DATETIME=y
+CONFIG_SCHED_ATEXIT=y
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_LPWORKPRIORITY=50
+CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_WAITPID=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SEM_NNESTPRIO=8
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STM32H7_ADC1=y
+CONFIG_STM32H7_ADC3=y
+CONFIG_STM32H7_BBSRAM=y
+CONFIG_STM32H7_BBSRAM_FILES=5
+CONFIG_STM32H7_BDMA=y
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_DMACAPABLE=y
+CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
+CONFIG_STM32H7_I2C1=y
+CONFIG_STM32H7_I2C_DYNTIMEO=y
+CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_RTC=y
+CONFIG_STM32H7_RTC_AUTO_LSECLOCK_START_DRV_CAPABILITY=y
+CONFIG_STM32H7_RTC_MAGIC_REG=1
+CONFIG_STM32H7_SAVE_CRASHDUMP=y
+CONFIG_STM32H7_SDMMC1=y
+CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_SPI1=y
+CONFIG_STM32H7_SPI2=y
+CONFIG_STM32H7_SPI4=y
+CONFIG_STM32H7_SPI4_DMA=y
+CONFIG_STM32H7_SPI4_DMA_BUFFER=1024
+CONFIG_STM32H7_SPI_DMA=y
+CONFIG_STM32H7_UART4=y
+CONFIG_STM32H7_UART7=y
+CONFIG_STM32H7_USART1=y
+CONFIG_STM32H7_USART2=y
+CONFIG_STM32H7_USART3=y
+CONFIG_STM32H7_USART6=y
+CONFIG_STM32H7_USART_BREAKS=y
+CONFIG_STM32H7_USART_INVERT=y
+CONFIG_STM32H7_USART_SINGLEWIRE=y
+CONFIG_STM32H7_USART_SWAP=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGTSTP=y
+CONFIG_UART4_BAUD=57600
+CONFIG_UART4_RXBUFSIZE=600
+CONFIG_UART4_TXBUFSIZE=1500
+CONFIG_UART7_BAUD=57600
+CONFIG_UART7_RXBUFSIZE=600
+CONFIG_UART7_TXBUFSIZE=1500
+CONFIG_USART1_BAUD=57600
+CONFIG_USART1_RXBUFSIZE=600
+CONFIG_USART1_TXBUFSIZE=1500
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_RXDMA=y
+CONFIG_USART2_TXBUFSIZE=2500
+CONFIG_USART3_BAUD=57600
+CONFIG_USART3_RXBUFSIZE=600
+CONFIG_USART3_SERIAL_CONSOLE=y
+CONFIG_USART3_TXBUFSIZE=1500
+CONFIG_USART6_BAUD=57600
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_USERMAIN_STACKSIZE=2944
+CONFIG_USER_ENTRYPOINT="nsh_main"
+CONFIG_WATCHDOG=y
@@ -0,0 +1,213 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2019 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The KakuteH7 uses an STM32H743VI has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743VI, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The KakuteH7 has a Swtich on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the swiutch is
+ * drepresed, then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743VI also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	flash (rx)  : ORIGIN = 0x08000000, LENGTH = 2048K
+	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
+	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
+	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
+	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
+	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
+	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
@@ -0,0 +1,222 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2019 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The KakuteH7 uses an STM32H743VI has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743VI, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The KakuteH7 has a Swtich on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the swiutch is
+ * drepresed, then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743VI also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	flash (rx)  : ORIGIN = 0x08020000, LENGTH = 1792K /* params in last sector */
+	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
+	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
+	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
+	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
+	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
+	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Emit the the D3 power domain section for locating BDMA data */
+
+	.sram4_reserve (NOLOAD) :
+	{
+		*(.sram4)
+		. = ALIGN(4);
+		_sram4_heap_start = ABSOLUTE(.);
+	} > sram4
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
@@ -0,0 +1,66 @@
+############################################################################
+#
+#   Copyright (c) 2016 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+if("${PX4_BOARD_LABEL}" STREQUAL  "bootloader")
+	add_library(drivers_board
+		bootloader_main.c
+		usb.c
+	)
+	target_link_libraries(drivers_board
+		PRIVATE
+			nuttx_arch # sdio
+			nuttx_drivers # sdio
+			bootloader
+	)
+	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common)
+
+else()
+	add_library(drivers_board
+		i2c.cpp
+		init.c
+		led.c
+		spi.cpp
+		timer_config.cpp
+		usb.c
+	)
+	add_dependencies(drivers_board arch_board_hw_info)
+
+	target_link_libraries(drivers_board
+		PRIVATE
+			arch_spi
+			arch_board_hw_info
+			drivers__led # drv_led_start
+			nuttx_arch # sdio
+			nuttx_drivers # sdio
+			px4_layer
+	)
+endif()
@@ -0,0 +1,214 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2019 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * holybro KakuteH7 internal definitions
+ */
+
+#pragma once
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+#include <stm32_gpio.h>
+
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+
+/* Configuration ************************************************************************************/
+
+#  define BOARD_HAS_USB_VALID           1
+#  define BOARD_HAS_NBAT_V              1
+#  define BOARD_HAS_NBAT_I              1
+
+/* Holybro KakuteH7 GPIOs ************************************************************************/
+
+/* LEDs are driven with push open drain to support Anode to 5V or 3.3V */
+
+#define GPIO_nLED_RED        /* PC2 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN2)
+
+#define BOARD_HAS_CONTROL_STATUS_LEDS      1
+#define BOARD_OVERLOAD_LED     LED_RED
+
+/*
+ * ADC channels
+ *
+ * These are the channel numbers of the ADCs of the microcontroller that
+ * can be used by the Px4 Firmware in the adc driver
+ */
+
+/* ADC defines to be used in sensors.cpp to read from a particular channel */
+
+#define ADC1_CH(n)                  (n)
+
+/* Define GPIO pins used as ADC N.B. Channel numbers must match below */
+
+#define PX4_ADC_GPIO  \
+	/* PC0 */  GPIO_ADC123_INP10, \
+	/* PC1 */  GPIO_ADC123_INP11, \
+	/* PC5 */  GPIO_ADC12_INP8
+
+/* Define Channel numbers must match above GPIO pin IN(n)*/
+
+#define ADC_BATTERY_VOLTAGE_CHANNEL        /* PC0 */  ADC1_CH(10)
+#define ADC_BATTERY_CURRENT_CHANNEL        /* PC1 */  ADC1_CH(11)
+#define ADC_RSSI_IN_CHANNEL                /* PC5 */  ADC1_CH(8)
+
+#define ADC_CHANNELS \
+	((1 << ADC_BATTERY_VOLTAGE_CHANNEL)       | \
+	 (1 << ADC_BATTERY_CURRENT_CHANNEL)       | \
+	 (1 << ADC_RSSI_IN_CHANNEL))
+
+#define BOARD_ADC_OPEN_CIRCUIT_V     (5.6f)
+
+
+
+/* PWM
+ */
+#define DIRECT_PWM_OUTPUT_CHANNELS  8
+
+#define BOARD_NUM_IO_TIMERS 4
+
+
+/* Tone alarm output */
+
+#define GPIO_TONE_ALARM_IDLE    /* PC13 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13)
+#define GPIO_TONE_ALARM_GPIO    /* PC13 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN13)
+
+/* USB OTG FS
+ *
+ * PA9  OTG_FS_VBUS VBUS sensing
+ */
+#define GPIO_OTGFS_VBUS         /* PA8 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTA|GPIO_PIN8)
+
+/* High-resolution timer */
+#define HRT_TIMER               4  /* use timer3 for the HRT */
+#define HRT_TIMER_CHANNEL       1  /* use capture/compare channel 1 */
+
+/* RC Serial port */
+
+/* PWM input driver. Use FMU AUX5 pins attached to timer4 channel 2 */
+
+#define PWMIN_TIMER                       5
+#define PWMIN_TIMER_CHANNEL    /* T5C1 */ 1
+#define GPIO_PWM_IN            /* PA0  */ GPIO_TIM5_CH1IN
+
+#define GPIO_RSSI_IN                       /* PC5  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTC|GPIO_PIN5)
+
+#define GPIO_RF_SWITCH                     /* PE13  */ (GPIO_OUTPUT|GPIO_PULLDOWN|GPIO_PORTE|GPIO_PIN13)
+
+/* Power switch controls ******************************************************/
+
+#define SDIO_SLOTNO                    0  /* Only one slot */
+#define SDIO_MINOR                     0
+
+/* SD card bringup does not work if performed on the IDLE thread because it
+ * will cause waiting.  Use either:
+ *
+ *  CONFIG_LIB_BOARDCTL=y, OR
+ *  CONFIG_BOARD_INITIALIZE=y && CONFIG_BOARD_INITTHREAD=y
+ */
+
+#if defined(CONFIG_BOARD_INITIALIZE) && !defined(CONFIG_LIB_BOARDCTL) && \
+   !defined(CONFIG_BOARD_INITTHREAD)
+#  warning SDIO initialization cannot be perfomed on the IDLE thread
+#endif
+
+/* By Providing BOARD_ADC_USB_CONNECTED (using the px4_arch abstraction)
+ * this board support the ADC system_power interface, and therefore
+ * provides the true logic GPIO BOARD_ADC_xxxx macros.
+ */
+#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS))
+
+/* Board never powers off the Servo rail */
+
+#define BOARD_ADC_SERVO_VALID     (1)
+
+#define BOARD_ADC_BRICK1_VALID  (1)
+
+
+
+/* This board provides a DMA pool and APIs */
+#define BOARD_DMA_ALLOC_POOL_SIZE 5120
+
+/* This board provides the board_on_reset interface */
+
+#define BOARD_HAS_ON_RESET 1
+
+#define PX4_GPIO_INIT_LIST { \
+		PX4_ADC_GPIO,                     \
+		GPIO_TONE_ALARM_IDLE,             \
+		GPIO_RSSI_IN,                     \
+		GPIO_RF_SWITCH,                   \
+	}
+
+#define BOARD_ENABLE_CONSOLE_BUFFER
+
+// not working on h7 yet, due to ECC
+//#define FLASH_BASED_PARAMS
+
+__BEGIN_DECLS
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+extern void stm32_spiinitialize(void);
+
+extern void stm32_usbinitialize(void);
+
+extern void board_peripheral_reset(int ms);
+
+#include <px4_platform_common/board_common.h>
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS
@@ -0,0 +1,75 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2019, 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file bootloader_main.c
+ *
+ * FMU-specific early startup code for bootloader
+*/
+
+#include "board_config.h"
+#include "bl.h"
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+#include <px4_platform_common/init.h>
+
+extern int sercon_main(int c, char **argv);
+
+__EXPORT void board_on_reset(int status) {}
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+}
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	return 0;
+}
+
+void board_late_initialize(void)
+{
+	sercon_main(0, NULL);
+}
+
+extern void sys_tick_handler(void);
+void board_timerhook(void)
+{
+	sys_tick_handler();
+}
@@ -0,0 +1,124 @@
+/*
+ * hw_config.h
+ *
+ *  Created on: May 17, 2015
+ *      Author: david_s5
+ */
+
+#ifndef HW_CONFIG_H_
+#define HW_CONFIG_H_
+
+/****************************************************************************
+ * 10-8--2016:
+ *  To simplify the ripple effect on the tools, we will be using
+ *  /dev/serial/by-id/<asterisk>PX4<asterisk> to locate PX4 devices. Therefore
+ *  moving forward all Bootloaders must contain the prefix "PX4 BL "
+ *  in the USBDEVICESTRING
+ *  This Change will be made in an upcoming BL release
+ ****************************************************************************/
+/*
+ * Define usage to configure a bootloader
+ *
+ *
+ * Constant                example          Usage
+ * APP_LOAD_ADDRESS     0x08004000            - The address in Linker Script, where the app fw is org-ed
+ * BOOTLOADER_DELAY     5000                  - Ms to wait while under USB pwr or bootloader request
+ * BOARD_FMUV2
+ * INTERFACE_USB        1                     - (Optional) Scan and use the USB interface for bootloading
+ * INTERFACE_USART      1                     - (Optional) Scan and use the Serial interface for bootloading
+ * USBDEVICESTRING      "PX4 BL FMU v2.x"     - USB id string
+ * USBPRODUCTID         0x0011                - PID Should match defconfig
+ * BOOT_DELAY_ADDRESS   0x000001a0            - (Optional) From the linker script from Linker Script to get a custom
+ *                                               delay provided by an APP FW
+ * BOARD_TYPE           9                     - Must match .prototype boad_id
+ * _FLASH_KBYTES        (*(uint16_t *)0x1fff7a22) - Run time flash size detection
+ * BOARD_FLASH_SECTORS  ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector
+ * BOARD_FLASH_SECTORS   11                   - Hard coded zero based last sector
+ * BOARD_FLASH_SIZE     (_FLASH_KBYTES*1024)-   Total Flash size of device, determined at run time.
+ *                         (1024 * 1024)      - Hard coded Total Flash of device - The bootloader and app reserved will be deducted
+ *                                              programmatically
+ *
+ * BOARD_FIRST_FLASH_SECTOR_TO_ERASE  2        - Optional sectors index in the flash_sectors table  (F4 only), to begin erasing.
+ *                                               This is to allow sectors to be reserved for app fw usage. That will NOT be erased
+ *                                               during a FW upgrade.
+ *                                               The default is 0, and selects the first sector to be erased, as the 0th entry in the
+ *                                               flash_sectors table. Which is the second physical sector of FLASH in the device.
+ *                                               The first physical sector of FLASH is used by the bootloader, and is not defined
+ *                                               in the table.
+ *
+ * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus
+ *                                                                        BOOTLOADER_RESERVATION_SIZE  will be deducted from
+ *                                                                        BOARD_FLASH_SIZE to determine the size of the App FW
+ *                                                                        and hence the address space of FLASH to erase and program.
+ * USBMFGSTRING            "PX4 AP"            - Optional USB MFG string (default is '3D Robotics' if not defined.)
+ * SERIAL_BREAK_DETECT_DISABLED                -  Optional prevent break selection on Serial port from entering or staying in BL
+ *
+ * * Other defines are somewhat self explanatory.
+ */
+
+/* Boot device selection list*/
+#define USB0_DEV       0x01
+#define SERIAL0_DEV    0x02
+#define SERIAL1_DEV    0x04
+
+#define APP_LOAD_ADDRESS               0x08020000
+#define BOOTLOADER_DELAY               3000
+#define INTERFACE_USB                  1
+#define INTERFACE_USB_CONFIG           "/dev/ttyACM0"
+#define BOARD_VBUS                     MK_GPIO_INPUT(GPIO_OTGFS_VBUS)
+
+//#define USE_VBUS_PULL_DOWN
+#define BOOT_DELAY_ADDRESS             0x000001a0
+#define BOARD_TYPE                     1048
+#define BOARD_FLASH_SECTORS            (14)
+#define BOARD_FLASH_SIZE               ((16-2) * 128 * 1024)
+
+#define OSC_FREQ                       8
+
+#define BOARD_PIN_LED_ACTIVITY         GPIO_nLED_RED
+#define BOARD_LED_ON                   0
+#define BOARD_LED_OFF                  1
+
+#define SERIAL_BREAK_DETECT_DISABLED   1
+
+/*
+ * Uncommenting this allows to force the bootloader through
+ * a PWM output pin. As this can accidentally initialize
+ * an ESC prematurely, it is not recommended. This feature
+ * has not been used and hence defaults now to off.
+ *
+ * # define BOARD_FORCE_BL_PIN_OUT         (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN14)
+ * # define BOARD_FORCE_BL_PIN_IN          (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN11)
+ *
+ * # define BOARD_POWER_PIN_OUT           (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
+ * # define BOARD_POWER_ON                 1
+ * # define BOARD_POWER_OFF                0
+ * # undef  BOARD_POWER_PIN_RELEASE        // Leave pin enabling Power - un comment to release (disable power)
+ *
+*/
+
+#if !defined(ARCH_SN_MAX_LENGTH)
+# define ARCH_SN_MAX_LENGTH 12
+#endif
+
+#if !defined(APP_RESERVATION_SIZE)
+#  define APP_RESERVATION_SIZE 0
+#endif
+
+#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE)
+#  define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1
+#endif
+
+#if !defined(USB_DATA_ALIGN)
+# define USB_DATA_ALIGN
+#endif
+
+#ifndef BOOT_DEVICES_SELECTION
+#  define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#ifndef BOOT_DEVICES_FILTER_ONUSB
+#  define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#endif /* HW_CONFIG_H_ */
@@ -0,0 +1,38 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2020 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/i2c_hw_description.h>
+
+constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
+	initI2CBusExternal(1),
+};
@@ -0,0 +1,271 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2012-2019 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file init.c
+ *
+ * PX4FMU-specific early startup code.  This file implements the
+ * board_app_initialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialisation.
+ */
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include "board_config.h"
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <string.h>
+#include <debug.h>
+#include <errno.h>
+#include <syslog.h>
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <nuttx/spi/spi.h>
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+#include <nuttx/analog/adc.h>
+#include <nuttx/mm/gran.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_board_led.h>
+#include <systemlib/px4_macros.h>
+#include <px4_arch/io_timer.h>
+#include <px4_platform_common/init.h>
+#include <px4_platform/gpio.h>
+#include <px4_platform/board_determine_hw_info.h>
+#include <px4_platform/board_dma_alloc.h>
+
+#include <mpu.h>
+
+# if defined(FLASH_BASED_PARAMS)
+#  include <parameters/flashparams/flashfs.h>
+#endif
+
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+__END_DECLS
+
+
+/************************************************************************************
+ * Name: board_peripheral_reset
+ *
+ * Description:
+ *
+ ************************************************************************************/
+__EXPORT void board_peripheral_reset(int ms)
+{
+}
+
+/************************************************************************************
+ * Name: board_on_reset
+ *
+ * Description:
+ * Optionally provided function called on entry to board_system_reset
+ * It should perform any house keeping prior to the rest.
+ *
+ * status - 1 if resetting to boot loader
+ *          0 if just resetting
+ *
+ ************************************************************************************/
+__EXPORT void board_on_reset(int status)
+{
+	for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) {
+		px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i)));
+	}
+
+	if (status >= 0) {
+		up_mdelay(6);
+	}
+}
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+__EXPORT void
+stm32_boardinitialize(void)
+{
+	board_on_reset(-1); /* Reset PWM first thing */
+
+	/* configure LEDs */
+
+	board_autoled_initialize();
+
+	/* configure pins */
+
+	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
+	px4_gpio_init(gpio, arraySize(gpio));
+
+	board_control_spi_sensors_power_configgpio();
+
+	/* Turn bluetooth off by default (no mavlink support yet) */
+	px4_arch_gpiowrite(GPIO_RF_SWITCH, 0);
+
+	/* configure USB interfaces */
+
+	stm32_usbinitialize();
+
+}
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX; the meaning of the argument is a contract
+ *         between the board-specific initalization logic and the the
+ *         matching application logic.  The value cold be such things as a
+ *         mode enumeration value, a set of DIP switch switch settings, a
+ *         pointer to configuration data read from a file or serial FLASH,
+ *         or whatever you would like to do with it.  Every implementation
+ *         should accept zero/NULL as a default configuration.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	/* Power on Interfaces */
+	board_control_spi_sensors_power(true, 0xffff);
+
+	/* Need hrt running before using the ADC */
+
+	px4_platform_init();
+
+	/* configure SPI interfaces */
+
+	stm32_spiinitialize();
+
+	/* configure the DMA allocator */
+
+	if (board_dma_alloc_init() < 0) {
+		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
+	}
+
+#if defined(SERIAL_HAVE_RXDMA)
+	// set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event.
+	static struct hrt_call serial_dma_call;
+	hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
+#endif
+
+	/* initial LED state */
+	drv_led_start();
+	led_off(LED_RED);
+
+	if (board_hardfault_init(2, true) != 0) {
+		led_on(LED_RED);
+	}
+
+	/* Get the SPI port for the microSD slot */
+	struct spi_dev_s *spi_dev = stm32_spibus_initialize(CONFIG_NSH_MMCSDSPIPORTNO);
+
+	if (!spi_dev) {
+		syslog(LOG_ERR, "[boot] FAILED to initialize SPI port %d\n", CONFIG_NSH_MMCSDSPIPORTNO);
+		led_on(LED_BLUE);
+	}
+
+	/* Now bind the SPI interface to the MMCSD driver */
+	int result = mmcsd_spislotinitialize(CONFIG_NSH_MMCSDMINOR, CONFIG_NSH_MMCSDSLOTNO, spi_dev);
+
+	if (result != OK) {
+		led_on(LED_BLUE);
+		syslog(LOG_ERR, "[boot] FAILED to bind SPI port 1 to the MMCSD driver\n");
+	}
+
+	up_udelay(20);
+
+
+#if defined(FLASH_BASED_PARAMS)
+	static sector_descriptor_t params_sector_map[] = {
+		{15, 128 * 1024, 0x081E0000},
+		{0, 0, 0},
+	};
+
+	/* Initialize the flashfs layer to use heap allocated memory */
+	result = parameter_flashfs_init(params_sector_map, NULL, 0);
+
+	if (result != OK) {
+		syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
+		led_on(LED_AMBER);
+	}
+
+#endif
+
+	/* Configure the HW based on the manifest */
+
+	px4_platform_configure();
+
+	return OK;
+}
@@ -0,0 +1,223 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2013 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+
+#include <stdbool.h>
+
+#include "chip.h"
+#include "stm32_gpio.h"
+#include "board_config.h"
+
+#include <nuttx/board.h>
+#include <arch/board/board.h>
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+extern void led_toggle(int led);
+__END_DECLS
+
+#ifdef CONFIG_ARCH_LEDS
+static bool nuttx_owns_leds = true;
+//                                B  R  S  G
+//                                0  1  2  3
+static const uint8_t xlatpx4[] = {1, 2, 4, 0};
+#  define xlat(p) xlatpx4[(p)]
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_RED,     // Indexed by BOARD_LED_RED
+};
+
+#else
+
+#  define xlat(p) (p)
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_RED,                      // Indexed by LED_RED, LED_AMBER
+};
+
+#endif
+
+__EXPORT void led_init(void)
+{
+	for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
+		if (g_ledmap[l] != 0) {
+			stm32_configgpio(g_ledmap[l]);
+		}
+	}
+}
+
+static void phy_set_led(int led, bool state)
+{
+	/* Drive Low to switch on */
+
+	if (g_ledmap[led] != 0) {
+		stm32_gpiowrite(g_ledmap[led], !state);
+	}
+}
+
+static bool phy_get_led(int led)
+{
+	/* If Low it is on */
+	if (g_ledmap[led] != 0) {
+		return !stm32_gpioread(g_ledmap[led]);
+	}
+
+	return false;
+}
+
+__EXPORT void led_on(int led)
+{
+	phy_set_led(xlat(led), true);
+}
+
+__EXPORT void led_off(int led)
+{
+	phy_set_led(xlat(led), false);
+}
+
+__EXPORT void led_toggle(int led)
+{
+	phy_set_led(xlat(led), !phy_get_led(xlat(led)));
+}
+
+#ifdef CONFIG_ARCH_LEDS
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_autoled_initialize
+ ****************************************************************************/
+
+void board_autoled_initialize(void)
+{
+	led_init();
+}
+
+/****************************************************************************
+ * Name: board_autoled_on
+ ****************************************************************************/
+
+void board_autoled_on(int led)
+{
+	if (!nuttx_owns_leds) {
+		return;
+	}
+
+	switch (led) {
+	default:
+		break;
+
+	case LED_HEAPALLOCATE:
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_IRQSENABLED:
+		phy_set_led(BOARD_LED_BLUE, false);
+		phy_set_led(BOARD_LED_GREEN, true);
+		break;
+
+	case LED_STACKCREATED:
+		phy_set_led(BOARD_LED_GREEN, true);
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_INIRQ:
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_SIGNAL:
+		phy_set_led(BOARD_LED_GREEN, true);
+		break;
+
+	case LED_ASSERTION:
+		phy_set_led(BOARD_LED_RED, true);
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_PANIC:
+		phy_set_led(BOARD_LED_RED, true);
+		break;
+
+	case LED_IDLE : /* IDLE */
+		phy_set_led(BOARD_LED_RED, true);
+		break;
+	}
+}
+
+/****************************************************************************
+ * Name: board_autoled_off
+ ****************************************************************************/
+
+void board_autoled_off(int led)
+{
+	if (!nuttx_owns_leds) {
+		return;
+	}
+
+	switch (led) {
+	default:
+		break;
+
+	case LED_SIGNAL:
+		phy_set_led(BOARD_LED_GREEN, false);
+		break;
+
+	case LED_INIRQ:
+		phy_set_led(BOARD_LED_BLUE, false);
+		break;
+
+	case LED_ASSERTION:
+		phy_set_led(BOARD_LED_RED, false);
+		phy_set_led(BOARD_LED_BLUE, false);
+		break;
+
+	case LED_PANIC:
+		phy_set_led(BOARD_LED_RED, false);
+		break;
+
+	case LED_IDLE : /* IDLE */
+		phy_set_led(BOARD_LED_RED, false);
+		break;
+	}
+}
+
+#endif /* CONFIG_ARCH_LEDS */
@@ -0,0 +1,51 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2020, 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/spi_hw_description.h>
+#include <drivers/drv_sensor.h>
+#include <nuttx/spi/spi.h>
+
+constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = {
+	initSPIBus(SPI::Bus::SPI1, {
+		initSPIDevice(SPIDEV_MMCSD(0), SPI::CS{GPIO::PortA, GPIO::Pin4})
+	}),
+	initSPIBus(SPI::Bus::SPI2, {
+		initSPIDevice(DRV_OSD_DEVTYPE_ATXXXX, SPI::CS{GPIO::PortB, GPIO::Pin12}),
+	}),
+	initSPIBus(SPI::Bus::SPI4, {
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM20689, SPI::CS{GPIO::PortE, GPIO::Pin4}, SPI::DRDY{GPIO::PortE, GPIO::Pin1}),
+		initSPIDevice(DRV_IMU_DEVTYPE_MPU6000, SPI::CS{GPIO::PortE, GPIO::Pin4}, SPI::DRDY{GPIO::PortE, GPIO::Pin1}),
+	}),
+};
+
+static constexpr bool unused = validateSPIConfig(px4_spi_buses);
@@ -0,0 +1,55 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/io_timer_hw_description.h>
+
+constexpr io_timers_t io_timers[MAX_IO_TIMERS] = {
+	initIOTimer(Timer::Timer3, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer2, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer5, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer8, DMA{DMA::Index1}),
+};
+
+constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel3}, {GPIO::PortB, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel4}, {GPIO::PortB, GPIO::Pin1}),
+	initIOTimerChannel(io_timers, {Timer::Timer2, Timer::Channel2}, {GPIO::PortB, GPIO::Pin3}),
+	initIOTimerChannel(io_timers, {Timer::Timer2, Timer::Channel3}, {GPIO::PortB, GPIO::Pin10}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel1}, {GPIO::PortA, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel3}, {GPIO::PortA, GPIO::Pin2}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel3}, {GPIO::PortC, GPIO::Pin8}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel4}, {GPIO::PortC, GPIO::Pin9}),
+};
+
+constexpr io_timers_channel_mapping_t io_timers_channel_mapping =
+	initIOTimerChannelMapping(io_timers, timer_io_channels);
@@ -0,0 +1,105 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2016 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file px4fmu_usb.c
+ *
+ * Board-specific USB functions.
+ */
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+
+#include <sys/types.h>
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/usb/usbdev.h>
+#include <nuttx/usb/usbdev_trace.h>
+
+#include <arm_arch.h>
+#include <chip.h>
+#include <stm32_gpio.h>
+#include <stm32_otg.h>
+#include "board_config.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_usbinitialize
+ *
+ * Description:
+ *   Called to setup USB-related GPIO pins for the PX4FMU board.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_usbinitialize(void)
+{
+	/* The OTG FS has an internal soft pull-up */
+
+	/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
+
+#ifdef CONFIG_STM32H7_OTGFS
+	stm32_configgpio(GPIO_OTGFS_VBUS);
+#endif
+}
+
+/************************************************************************************
+ * Name:  stm32_usbsuspend
+ *
+ * Description:
+ *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
+ *   used.  This function is called whenever the USB enters or leaves suspend mode.
+ *   This is an opportunity for the board logic to shutdown clocks, power, etc.
+ *   while the USB is suspended.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
+{
+	uinfo("resume: %d\n", resume);
+}
@@ -79,7 +79,7 @@ CONFIG_MODULES_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_VMOUNT=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
@@ -430,7 +430,6 @@

 #define BOARD_NUM_IO_TIMERS 5

-#define BOARD_DSHOT_MOTOR_ASSIGNMENT {3, 2, 1, 0, 4, 5, 6, 7, 8, 9, 10};

 __BEGIN_DECLS

@@ -0,0 +1,7 @@
+CONFIG_PLATFORM_NUTTX=y
+CONFIG_BOARD_PLATFORM="nuttx"
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m4"
+CONFIG_BOARD_ROMFSROOT=""
+CONFIG_BOARD_CONSTRAINED_MEMORY=y
+CONFIG_DRIVERS_BOOTLOADERS=y
@@ -0,0 +1,25 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m4"
+CONFIG_BOARD_ROMFSROOT="cannode"
+CONFIG_BOARD_CONSTRAINED_MEMORY=y
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS2"
+CONFIG_DRIVERS_BAROMETER_DPS310=y
+CONFIG_DRIVERS_BOOTLOADERS=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
+CONFIG_DRIVERS_MAGNETOMETER_RM3100=y
+CONFIG_BOARD_UAVCAN_INTERFACES=1
+CONFIG_DRIVERS_UAVCANNODE=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SERIAL_PASSTHRU=y
+CONFIG_SERIAL_PASSTHRU_UBLOX=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y
--- a/Show More
+++ b/Show More