nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* drivers: disable INS by default
With the growing number of INS drivers some targets are running out of flash
and its becoming challenge to keep them under the limit.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Update boards/nxp/tropic-community/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update boards/px4/fmu-v6xrt/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Fix comments from review:
- Switch ssh link to https link in submodule
- Remove mc_nn_control from startup
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Remove auto start
* Add logging from neural control module
* Fix automatic startup to only be when module is included
* Switch to flight mode registration
* Add docs
* Change min/max/coeff to actual parameters
* add figures to neural network docs
* Switch to e2e network
* Remove toolchain changes and replace with instructions in docs
* Get ready for merge after toolchain upgrade
* switch back to submodule
* Try to figure out cmake
* Get CI working with new toolchain
* Remove fork dependency
* Finalize PR
* fix toolchain inclusion
* Fix ctype_base.h include
* Cleanup includes for TFLM
* Remove redundant std
* Update FW module names in board files
* Fix docs
* Remove cstdlib copy
* Copy header from nuttx
* Prettier, markup, layout
* NeuralControl.msg - update uorb comments to current standard
* Add description to neural topic
* Fix typo
* Typo
* TFLM and Module utitlities
* Neural networks top level
* Update docs
* Add manual control
* Update docs
* Revert the manual control attempt
* Update docs/en/advanced/nn_module_utilities.md
* Add posibility to set trajectory setpoint with manual control
---------
Co-authored-by: Pedro Roque <padr@kth.se>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* rft: clean merge to PX4
* fix: formatting
* fix: extra line
* fix: moved submarine out of "is_ground_vehicle", added proper check for center-throttle
* feat: updated gazebo models to include bluerov update
* fix: use 'is_uuv_vehicle', remove FW_MM/LLC from uuv build
* fix: added saturation to thrust and torque messages via param
* doc: updated parameters documentation for uuv
* fix: formatting
* feat: matching hardware reference
* fix: thrusters kg
* rft: removed commented lines
* fix: update gz reference given hw setup
* fix: hardware references
* fix: recommendations
* fix: updated settings to match hardware
* rft: check only for fixed and rotary wing for high throttle
Co-authored-by: Daniel Agar <daniel@agar.ca>
* fix: commit oupsie
* fix: format
* rft: remove is_uuv
* fix: hw parameters, uuv build target for v6x
* feat: added support for D-pad attitude changes in stabilized position control
* fix: position setpoint update and parametrized trajectory age and att change
* fix: format
* fix: removed duplicated call to check_validity_setpoint
* fix: setpoint update on arming logic
* fix: setpoint initialization for stabilized mode
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* feat: spacecraft tooling for commander and VehicleStatus
* feat: spacecraft tooling for commander and VehicleStatus
* fix: format
* fix: format
* fix: remove iostream
* fix: remove iostream
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* boards: Increase TELEM2 rx buffer size for DDS over serial use-case (ARK Jetson)
feat: spacecraft tooling for commander and VehicleStatus
fix: format
fix: remove iostream
feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* feat: add orbiter to define
* fix: change mav_type to new spacecraft orbiter enum value
* fix: build issue
* feat: update mavlink
* feat: update mavlink to latest master with spacecraft
* feat: update mavlink
* feat: update mavlink to latest
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: removed unnecessary definition
* fix: format
* feat: cmake variant for spacecraft
* feat: proper mav_type and rc init
* fix: removed dart from build system
* add: thrusters to actuator type
* rft: reordering actuator type
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* fix: format
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: add orbiter to define
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: conflicts
* fix: format
* fix: remove duplicate entry
* rft: remove Kconfig changes
* rft: revert main Kconfig
* rft: revert main kcoonfig on platforms
* rft: remove changes to board PWm (go on another PR)
* rft: revert changes to commander (main is correct)
* fix: extra char on commander_helper
* rft: removed extra spaces
* rft: moved effectiveness to spacecraft
* fix: spacecraft effectiveness
* fix: extra space
* feat: preliminary version, still using thrusters
* rft: initial pipeline on PX4 side with rotors instead of thrusters
* feat: add atmos model
* feat: spacecraft with rotor pipeline tested, working
* feat: update gz
* rft: removed thruster interfaces
* fix: format
* fix: remove control allocation
* fix: thruster normalization
* fix: format
* fix: nuttx version
* fix: clang tidy error
* feat: updated gz to add atmos model
* fix: update gz
* fix: update mavlink
* fix: remove friend class from allocation lib
* fix: remove actuator_outputs/motors
---------
Co-authored-by: Alexander Lerach <alexander@auterion.com>
* feat: configurable board pwm freq from Kconfig
* feat: add board_pwm_config to submenu
* fix: define sequence correction
* fix: revert Tools/simulation/gz
* fix: track upstream gz
* fix: track upstream mavlink
* feat: adjustable pwm for multiple board types
* feat: add conditional check for CONFIG_ for correct fallback
* add: spacecraft board with correct BOARD_PWM_FREQ supporting 10Hz actuation rate
* fix: set dependencies for submenu arch chips
* fix: keep only upper arch level
* fix: proper checking - still not showing up for board config
* feat: add hidden kconfig for platforms
* Merge Nuttx config into px4board
Allows to expose nuttx into PX4 if needed
* Kconfig: Include nuttx symbols in updateconfig
Only if applicable i.e. defined in the kconfig
* fix: merged config with previously generated boardconfig
* doc: updated code comment
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
