* Remove support for MAVLink 1
* Add back support for MAVLink 1 but don't default to it
* Update src/modules/mavlink/mavlink_params.c
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
---------
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Move ramvectors from DTCM to ITCM, this seems to better in general.
Also ITCM is marked as RO so is safer anyhow, now that DTCM is fully
unused we add DTCM region of 256kB to memory allocator. Increases usable
memory from 1536kB to 1792kB and decrease system load a bit since DTCM
is faster
* s32k3xx: EMIOS allow independent frequencies for each channel
* mr-canhubk3: update config
* mr-canhubk344: Fix adap board detect
* mr-canhubk344: Use LPSPI1 (Port P1A) for SD card
* airframes: Add B3RB Ackermann rover config
See https://nxp.gitbook.io/mr-b3rb for more information about the NXP
B3RB platform. PX4 Support basic control for now
The UARTs themselves were already present, just not configured under any
alias.
Follow [ArduPilot UART naming for this
board](https://ardupilot.org/plane/docs/common-pixracer-pro.html#default-uart-order),
out of necessity: it's the only combination that makes sense and is
understood by QGroundControl.
(For example, I've attempted configuring the additional UARTs as `_EXT1`
and `_EXT2`, but only `_EXT2` was understood by QGC.)
Trying to actually use the FrSky telemetry port for anything without
configuring FrSky telemetry on a different port may be impossible without
modifying the board's `init/rc.board_extras`.
(Should that script be modified to check if the port is used for
anything else?)
Skip naming the RC input port.
Fixes#21455.
nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* drivers: disable INS by default
With the growing number of INS drivers some targets are running out of flash
and its becoming challenge to keep them under the limit.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Update boards/nxp/tropic-community/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update boards/px4/fmu-v6xrt/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
