It was added at a time where the triplet target was directly fed as position setpoint to the controller.
Since the smoothing improvements to FlightTaskAuto(SmoothVel) and removing the previous "aggressive" FlightTaskAuto variant there should be no need anymore for this logic. It can sometimes lead to unexpected sideffects. E.g. the vehicle would suddenly change direction when exceeding some arbitrary threshold.
* rt106x: Use platform SPI hal layer
* rt106x: Add romapi support and reboot to isp/bootloader
* bootloader: imxrt_common: Add rt106x support
* NXP MR-Tropic initial commit
* Add missing file for mr-tropic bootloader
* nxp-mr-tropic:Bootloader Alow Assertion debugging & Keep Ram Vectors
* nxp-mr-tropic: Firmware Boot from bootloader
* nxp-mr-tropic:Add Bootloader bin file
* mr-tropic: Update config and linker
Fixes enet issues with write-back and some code cleanup.
Furthermore increase NOR LittleFS to 256kB to reflect on linker
* Update NuttX
* mr-tropic: fix itcm apping and add mr-tropic to itcm check
---------
Co-authored-by: David Sidrane <David.Sidrane@NscDg.com>
* s32k3xx: EMIOS allow independent frequencies for each channel
* mr-canhubk3: update config
* mr-canhubk344: Fix adap board detect
* mr-canhubk344: Use LPSPI1 (Port P1A) for SD card
* airframes: Add B3RB Ackermann rover config
See https://nxp.gitbook.io/mr-b3rb for more information about the NXP
B3RB platform. PX4 Support basic control for now
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
192.168.0.x is often used by routers for WIFI/ethernet networks, and thus
can create conflicts.
This can happen for example if a companion is connected to the FMU via
ethernet and at the same time connects to a WIFI network as DHCP client.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
