mavlink: return unsupported frame result when that's the case

mavlink: spacing, naming of command frame handling
Update MAVLink to contain _INT frame deprecation warning
2026-06-04 13:30:05 +08:00 · 2024-05-02 17:32:37 +02:00 · 2024-05-02 17:30:59 +02:00 · 2024-05-02 17:19:31 +02:00 · 2024-05-02 16:49:37 +02:00 · 2024-05-02 16:49:37 +02:00
256 changed files with 1086 additions and 10100 deletions
@@ -46,10 +46,8 @@ pipeline {
                     "ark_cannode_default",
                     "ark_fmu-v6x_bootloader",
                     "ark_fmu-v6x_default",
-                     "ark_fpv_bootloader",
-                     "ark_fpv_default",
                     "ark_pi6x_bootloader",
-                     "ark_pi6x_default",
+                     "ark_pi6x_default"
                     "atl_mantis-edu_default",
                     "av_x-v1_default",
                     "bitcraze_crazyflie21_default",
@@ -15,6 +15,7 @@
 	"extensions": [
 		"chiehyu.vscode-astyle",
 		"dan-c-underwood.arm",
+		"editorconfig.editorconfig",
 		"fredericbonnet.cmake-test-adapter",
 		"github.vscode-pull-request-github",
 		"marus25.cortex-debug",
@@ -181,16 +181,6 @@ CONFIG:
      buildType: MinSizeRel
      settings:
        CONFIG: ark_fmu-v6x_default
-    ark_fpv_bootloader:
-      short: ark_fpv_bootloader
-      buildType: MinSizeRel
-      settings:
-        CONFIG: ark_fpv_bootloader
-    ark_fpv_default:
-      short: ark_fpv_default
-      buildType: MinSizeRel
-      settings:
-        CONFIG: ark_fpv_default
    ark_pi6x_bootloader:
      short: ark_pi6x_bootloader
      buildType: MinSizeRel
@@ -4,6 +4,7 @@
    "recommendations": [
        "chiehyu.vscode-astyle",
        "dan-c-underwood.arm",
+        "editorconfig.editorconfig",
        "fredericbonnet.cmake-test-adapter",
        "github.vscode-pull-request-github",
        "marus25.cortex-debug",
@@ -1,6 +1,6 @@
 ############################################################################
 #
-# Copyright (c) 2017 - 2024 PX4 Development Team. All rights reserved.
+# Copyright (c) 2017 - 2022 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -132,9 +132,7 @@ list(GET VERSION_LIST 2 PX4_VERSION_PATCH)
 string(REPLACE "-" ";" PX4_VERSION_PATCH ${PX4_VERSION_PATCH})
 list(GET PX4_VERSION_PATCH 0 PX4_VERSION_PATCH)

-# # Capture only the hash part after 'g'
-string(REGEX MATCH "g([a-f0-9]+)$" GIT_HASH "${PX4_GIT_TAG}")
-set(PX4_GIT_HASH ${CMAKE_MATCH_1})
+message(STATUS "PX4 version: ${PX4_GIT_TAG} (${PX4_VERSION_MAJOR}.${PX4_VERSION_MINOR}.${PX4_VERSION_PATCH})")

 define_property(GLOBAL PROPERTY PX4_MODULE_LIBRARIES
                 BRIEF_DOCS "PX4 module libs"
@@ -1,6 +1,6 @@
 ############################################################################
 #
-# Copyright (c) 2015 - 2024 PX4 Development Team. All rights reserved.
+# Copyright (c) 2015 - 2020 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -323,33 +323,7 @@ px4io_update:
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeyellow/extras/cubepilot_io-v2_default.bin
 	git status

-bootloaders_update: \
-	ark_fmu-v6x_bootloader \
-	ark_fpv_bootloader \
-	ark_pi6x_bootloader \
-	cuav_nora_bootloader \
-	cuav_x7pro_bootloader \
-	cubepilot_cubeorange_bootloader \
-	cubepilot_cubeorangeplus_bootloader \
-	hkust_nxt-dual_bootloader \
-	hkust_nxt-v1_bootloader \
-	holybro_durandal-v1_bootloader \
-	holybro_kakuteh7_bootloader \
-	holybro_kakuteh7mini_bootloader \
-	holybro_kakuteh7v2_bootloader \
-	matek_h743_bootloader \
-	matek_h743-mini_bootloader \
-	matek_h743-slim_bootloader \
-	modalai_fc-v2_bootloader \
-	mro_ctrl-zero-classic_bootloader \
-	mro_ctrl-zero-h7_bootloader \
-	mro_ctrl-zero-h7-oem_bootloader \
-	mro_pixracerpro_bootloader \
-	px4_fmu-v6c_bootloader \
-	px4_fmu-v6u_bootloader \
-	px4_fmu-v6x_bootloader \
-	px4_fmu-v6xrt_bootloader \
-	siyi_n7_bootloader
+bootloaders_update: ark_fmu-v6x_bootloader cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader holybro_kakuteh7_bootloader matek_h743_bootloader matek_h743-mini_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6c_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
 	git status

 .PHONY: coverity_scan
@@ -439,14 +439,6 @@ else
 	# Must be started after the serial config is read
 	rc_input start $RC_INPUT_ARGS

-	# Manages USB interface
-	if ! cdcacm_autostart start
-	then
-		sercon
-		echo "Starting MAVLink on /dev/ttyACM0"
-		mavlink start -d /dev/ttyACM0
-	fi
-
 	#
 	# Play the startup tune (if not disabled or there is an error)
 	#
@@ -34,24 +34,23 @@ def extract_timer(line):
    if search:
        return search.group(1), 'generic'

-    # nxp rt1062 format: initIOPWM(PWM::FlexPWM2),
-    search = re.search('PWM::Flex([0-9a-zA-Z_]+)[,\)]', line, re.IGNORECASE)
+    # NXP FlexPWM format format: initIOPWM(PWM::FlexPWM2),
+    search = re.search('PWM::Flex([0-9a-zA-Z_]+)..PWM::Submodule([0-9])[,\)]', line, re.IGNORECASE)
    if search:
-        return search.group(1), 'imxrt'
+        return (search.group(1) + '_' +  search.group(2)), 'imxrt'

    return None, 'unknown'

-def extract_timer_from_channel(line, num_channels_already_found):
+def extract_timer_from_channel(line, timer_names):
    # Try format: initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel1}, {GPIO::PortA, GPIO::Pin0}),
    search = re.search('Timer::([0-9a-zA-Z_]+), ', line, re.IGNORECASE)
    if search:
        return search.group(1)

-    # nxp rt1062 format: initIOTimerChannel(io_timers, {PWM::PWM2_PWM_A, PWM::Submodule0}, IOMUX::Pad::GPIO_B0_06),
-    search = re.search('PWM::(PWM[0-9]+)[_,\)]', line, re.IGNORECASE)
+    # NXP FlexPWM format: initIOTimerChannel(io_timers, {PWM::PWM2_PWM_A, PWM::Submodule0}, IOMUX::Pad::GPIO_B0_06),
+    search = re.search('PWM::(PWM[0-9]+).*PWM::Submodule([0-9])', line, re.IGNORECASE)
    if search:
-        # imxrt uses a 1:1 timer group to channel association
-        return str(num_channels_already_found)
+        return str(timer_names.index((search.group(1) + '_' +  search.group(2))))

    return None

@@ -69,6 +68,7 @@ def get_timer_groups(timer_config_file, verbose=False):
    open_idx, close_idx = find_matching_brackets(('{', '}'), timer_config, verbose)
    timers_str = timer_config[open_idx:close_idx]
    timers = []
+    timer_names = []
    for line in timers_str.splitlines():
        line = line.strip()
        if len(line) == 0 or line.startswith('//'):
@@ -77,14 +77,12 @@ def get_timer_groups(timer_config_file, verbose=False):

        if timer_type == 'imxrt':
            if verbose: print('imxrt timer found')
-            max_num_channels = 16 # Just add a fixed number of timers
-            timers = [str(i) for i in range(max_num_channels)]
-            dshot_support = {str(i): False for i in range(max_num_channels)}
+            timer_names.append(timer)
+            timers.append(str(len(timers)))
+            dshot_support = {str(i): False for i in range(16)}
            for i in range(8): # First 8 channels support dshot
                dshot_support[str(i)] = True
-            break
-
-        if timer:
+        elif timer:
            if verbose: print('found timer def: {:}'.format(timer))
            dshot_support[timer] = 'DMA' in line
            timers.append(timer)
@@ -111,7 +109,7 @@ def get_timer_groups(timer_config_file, verbose=False):
            continue

        if verbose: print('--'+line+'--')
-        timer = extract_timer_from_channel(line, len(channel_timers))
+        timer = extract_timer_from_channel(line, timer_names)

        if timer:
            if verbose: print('Found timer: {:} in channel line {:}'.format(timer, line))
@@ -1,7 +1,7 @@
 #!/usr/bin/env python3
 ############################################################################
 #
-#   Copyright (c) 2012-2024 PX4 Development Team. All rights reserved.
+#   Copyright (c) 2012-2017 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -50,6 +50,9 @@
 #       Currently only used for informational purposes.
 #

+# for python2.7 compatibility
+from __future__ import print_function
+
 import sys
 import argparse
 import binascii
@@ -67,32 +70,35 @@ from sys import platform as _platform
 try:
    import serial
 except ImportError as e:
-    print(f"Failed to import serial: {e}")
+    print("Failed to import serial: " + str(e))
    print("")
    print("You may need to install it using:")
-    print("    python -m pip install pyserial")
+    print("    pip3 install --user pyserial")
    print("")
    sys.exit(1)


+# Define time to use time.time() by default
+def _time():
+    return time.time()
+
 # Detect python version
 if sys.version_info[0] < 3:
-    raise RuntimeError("Python 2 is not supported. Please try again using Python 3.")
-    sys.exit(1)
-
-
-# Use monotonic time where available
-def _time():
-    try:
-        return time.monotonic()
-    except Exception:
-        return time.time()
+    runningPython3 = False
+else:
+    runningPython3 = True
+    if sys.version_info[1] >=3:
+        # redefine to use monotonic time when available
+        def _time():
+            try:
+                return time.monotonic()
+            except Exception:
+                return time.time()

 class FirmwareNotSuitableException(Exception):
    def __init__(self, message):
        super(FirmwareNotSuitableException, self).__init__(message)

-
 class firmware(object):
    '''Loads a firmware file'''

@@ -157,13 +163,13 @@ class firmware(object):

    def crc(self, padlen):
        state = self.__crc32(self.image, int(0))
-        for _ in range(len(self.image), (padlen - 1), 4):
+        for i in range(len(self.image), (padlen - 1), 4):
            state = self.__crc32(self.crcpad, state)
        return state


-class uploader:
-    '''Uploads a firmware file to the PX4 bootloader'''
+class uploader(object):
+    '''Uploads a firmware file to the PX FMU bootloader'''

    # protocol bytes
    INSYNC          = b'\x12'
@@ -189,8 +195,6 @@ class uploader:
    GET_CHIP        = b'\x2c'     # rev5+  , get chip version
    SET_BOOT_DELAY  = b'\x2d'     # rev5+  , set boot delay
    GET_CHIP_DES    = b'\x2e'     # rev5+  , get chip description in ASCII
-    GET_VERSION     = b'\x2f'     # rev5+  , get chip description in ASCII
-    CHIP_FULL_ERASE = b'\x40'     # full erase of flash, rev6+
    MAX_DES_LENGTH  = 20

    REBOOT          = b'\x30'
@@ -201,7 +205,6 @@ class uploader:
    INFO_BOARD_ID   = b'\x02'        # board type
    INFO_BOARD_REV  = b'\x03'        # board revision
    INFO_FLASH_SIZE = b'\x04'        # max firmware size in bytes
-    BL_VERSION      = b'\x07'        # get bootloader version, e.g. major.minor.patch.githash (up to 20 chars)

    PROG_MULTI_MAX  = 252            # protocol max is 255, must be multiple of 4
    READ_MULTI_MAX  = 252            # protocol max is 255
@@ -232,7 +235,6 @@ class uploader:
        self.baudrate_bootloader = baudrate_bootloader
        self.baudrate_flightstack = baudrate_flightstack
        self.baudrate_flightstack_idx = -1
-        self.force_erase = False

    def close(self):
        if self.port is not None:
@@ -355,22 +357,19 @@ class uploader:
            self.port.baudrate = self.baudrate_bootloader * 2.33
        except NotImplementedError as e:
            # This error can occur because pySerial on Windows does not support odd baudrates
-            print(f"{e} -> could not check for FTDI device, assuming USB connection")
+            print(str(e) + " -> could not check for FTDI device, assuming USB connection")
            return

        self.__send(uploader.GET_SYNC +
                    uploader.EOC)
        try:
            self.__getSync(False)
-        except RuntimeError:
+        except:
            # if it fails we are on a real serial port - only leave this enabled on Windows
            if sys.platform.startswith('win'):
                self.ackWindowedMode = True
        finally:
-            try:
-                self.port.baudrate = self.baudrate_bootloader
-            except Exception:
-                pass
+            self.port.baudrate = self.baudrate_bootloader

    # send the GET_DEVICE command and wait for an info parameter
    def __getInfo(self, param):
@@ -411,17 +410,6 @@ class uploader:
        pieces = value.split(b",")
        return pieces

-    def __getVersion(self):
-        self.__send(uploader.GET_VERSION + uploader.EOC)
-        try:
-            length = self.__recv_int()
-            value = self.__recv(length)
-            self.__getSync()
-        except RuntimeError:
-            # Bootloader doesn't support version call
-            return "unknown"
-        return value.decode()
-
    def __drawProgressBar(self, label, progress, maxVal):
        if maxVal < progress:
            progress = maxVal
@@ -433,16 +421,10 @@ class uploader:

    # send the CHIP_ERASE command and wait for the bootloader to become ready
    def __erase(self, label):
-        print(f"Windowed mode: {self.ackWindowedMode}")
+        print("Windowed mode: %s" % self.ackWindowedMode)
        print("\n", end='')
-
-        if self.force_erase:
-            print("Trying force erase of full chip...\n")
-            self.__send(uploader.CHIP_FULL_ERASE +
-                        uploader.EOC)
-        else:
-            self.__send(uploader.CHIP_ERASE +
-                        uploader.EOC)
+        self.__send(uploader.CHIP_ERASE +
+                    uploader.EOC)

        # erase is very slow, give it 30s
        deadline = _time() + 30.0
@@ -459,14 +441,9 @@ class uploader:

            if self.__trySync():
                self.__drawProgressBar(label, 10.0, 10.0)
-                if self.force_erase:
-                    print("\nForce erase done.\n")
                return

-        if self.force_erase:
-            raise RuntimeError("timed out waiting for erase, force erase is likely not supported by bootloader!")
-        else:
-            raise RuntimeError("timed out waiting for erase")
+        raise RuntimeError("timed out waiting for erase")

    # send a PROG_MULTI command to write a collection of bytes
    def __program_multi(self, data, windowMode):
@@ -604,11 +581,8 @@ class uploader:
        self.board_rev = self.__getInfo(uploader.INFO_BOARD_REV)
        self.fw_maxsize = self.__getInfo(uploader.INFO_FLASH_SIZE)

-        self.version = self.__getVersion()
-
    # upload the firmware
-    def upload(self, fw_list, force=False, boot_delay=None, boot_check=False, force_erase=False):
-        self.force_erase = force_erase
+    def upload(self, fw_list, force=False, boot_delay=None, boot_check=False):
        # select correct binary
        found_suitable_firmware = False
        for file in fw_list:
@@ -637,8 +611,6 @@ class uploader:
        print("Loaded firmware for board id: %s,%s size: %d bytes (%.2f%%) " % (fw.property('board_id'), fw.property('board_revision'), fw.property('image_size'), percent))
        print()

-        print(f"Bootloader version: {self.version}")
-
        # Make sure we are doing the right thing
        start = _time()
        if self.board_type != fw.property('board_id'):
@@ -668,14 +640,14 @@ class uploader:
            self.otp_coa = self.otp[32:160]
            # show user:
            try:
-                print("Sn: ", end='')
+                print("sn: ", end='')
                for byte in range(0, 12, 4):
                    x = self.__getSN(byte)
                    x = x[::-1]  # reverse the bytes
                    self.sn = self.sn + x
                    print(binascii.hexlify(x).decode('Latin-1'), end='')  # show user
                print('')
-                print("Chip: %08x" % self.__getCHIP())
+                print("chip: %08x" % self.__getCHIP())

                otp_id = self.otp_id.decode('Latin-1')
                if ("PX4" in otp_id):
@@ -685,19 +657,17 @@ class uploader:
                    print("OTP pid: " + binascii.hexlify(self.otp_pid).decode('Latin-1'))
                    print("OTP coa: " + binascii.b2a_base64(self.otp_coa).decode('Latin-1'))

-            except Exception as e:
+            except Exception:
                # ignore bad character encodings
-                print(f"Exception ignored: {e}")
                pass

        # Silicon errata check was added in v5
        if (self.bl_rev >= 5):
            des = self.__getCHIPDes()
            if (len(des) == 2):
-                family, revision = des
-                print(f"Family: {family.decode()}")
-                print(f"Revision: {revision.decode()}")
-                print(f"Flash: {self.fw_maxsize} bytes")
+                print("family: %s" % des[0])
+                print("revision: %s" % des[1])
+                print("flash: %d bytes" % self.fw_maxsize)

                # Prevent uploads where the maximum image size of the board config is smaller than the flash
                # of the board. This is a hint the user chose the wrong config and will lack features
@@ -708,7 +678,8 @@ class uploader:
                # https://github.com/PX4/Firmware/blob/master/src/drivers/boards/common/stm32/board_mcu_version.c#L125-L144

                if self.fw_maxsize > fw.property('image_maxsize') and not force:
-                    raise RuntimeError(f"Board can accept larger flash images ({self.fw_maxsize} bytes) than board config ({fw.property('image_maxsize')} bytes). Please use the correct board configuration to avoid lacking critical functionality.")
+                    raise RuntimeError("Board can accept larger flash images (%u bytes) than board config (%u bytes). Please use the correct board configuration to avoid lacking critical functionality."
+                                       % (self.fw_maxsize, fw.property('image_maxsize')))
        else:
            # If we're still on bootloader v4 on a Pixhawk, we don't know if we
            # have the silicon errata and therefore need to flash px4_fmu-v2
@@ -809,13 +780,16 @@ class uploader:


 def main():
+    # Python2 is EOL
+    if not runningPython3:
+        raise RuntimeError("Python 2 is not supported. Please try again using Python 3.")
+
    # Parse commandline arguments
    parser = argparse.ArgumentParser(description="Firmware uploader for the PX autopilot system.")
    parser.add_argument('--port', action="store", required=True, help="Comma-separated list of serial port(s) to which the FMU may be attached")
    parser.add_argument('--baud-bootloader', action="store", type=int, default=115200, help="Baud rate of the serial port (default is 115200) when communicating with bootloader, only required for true serial ports.")
    parser.add_argument('--baud-flightstack', action="store", default="57600", help="Comma-separated list of baud rate of the serial port (default is 57600) when communicating with flight stack (Mavlink or NSH), only required for true serial ports.")
    parser.add_argument('--force', action='store_true', default=False, help='Override board type check, or silicon errata checks and continue loading')
-    parser.add_argument('--force-erase', action="store_true", help="Do not perform the blank check, always erase every sector of the application space")
    parser.add_argument('--boot-delay', type=int, default=None, help='minimum boot delay to store in flash')
    parser.add_argument('--use-protocol-splitter-format', action='store_true', help='use protocol splitter format for reboot')
    parser.add_argument('firmware', action="store", nargs='+', help="Firmware file(s)")
@@ -893,10 +867,9 @@ def main():
                        # Windows, don't open POSIX ports
                        if "/" not in port:
                            up = uploader(port, args.baud_bootloader, baud_flightstack)
-                except Exception as e:
+                except Exception:
                    # open failed, rate-limit our attempts
                    time.sleep(0.05)
-                    print(f"Exception ignored: {e}")

                    # and loop to the next port
                    continue
@@ -911,10 +884,10 @@ def main():
                        up.identify()
                        found_bootloader = True
                        print()
-                        print(f"Found board id: {up.board_type},{up.board_rev} bootloader protocol revision {up.bl_rev} on {port}")
+                        print("Found board id: %s,%s bootloader version: %s on %s" % (up.board_type, up.board_rev, up.bl_rev, port))
                        break

-                    except (RuntimeError, serial.SerialException):
+                    except Exception:

                        if not up.send_reboot(args.use_protocol_splitter_format):
                            break
@@ -934,14 +907,14 @@ def main():

                try:
                    # ok, we have a bootloader, try flashing it
-                    up.upload(args.firmware, force=args.force, boot_delay=args.boot_delay, force_erase=args.force_erase)
+                    up.upload(args.firmware, force=args.force, boot_delay=args.boot_delay)

                    # if we made this far without raising exceptions, the upload was successful
                    successful = True

-                except RuntimeError as e:
+                except RuntimeError as ex:
                    # print the error
-                    print(f"\n\nError: {e}")
+                    print("\nERROR: %s" % ex.args)

                except FirmwareNotSuitableException:
                    unsuitable_board = True
@@ -12,7 +12,6 @@ CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
@@ -6,6 +6,7 @@
 param set-default CBRK_IO_SAFETY 0
 param set-default CANNODE_SUB_MBD 1
 param set-default CANNODE_SUB_RTCM 1
+param set-default GPS_1_GNSS 63
 param set-default MBE_ENABLE 1
 param set-default SENS_IMU_CLPNOTI 0

@@ -47,7 +47,7 @@
 #define GPIO_BTN_SAFETY       /* PB15 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTB|GPIO_PIN15)

 /* Safety LED */
-#define GPIO_LED_SAFETY       /* PA1  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN1)
+#define GPIO_LED_SAFETY       /* PA1  */ (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN1)

 /* Tone alarm output. */
 #define TONE_ALARM_TIMER             2    /* timer 2 */
@@ -8,7 +8,6 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
 CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
@@ -1,3 +0,0 @@
-CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
-CONFIG_BOARD_ARCHITECTURE="cortex-m7"
-CONFIG_BOARD_ROMFSROOT=""
@@ -1,74 +0,0 @@
-CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
-CONFIG_BOARD_ARCHITECTURE="cortex-m7"
-CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS0"
-CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
-CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
-CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
-CONFIG_BOARD_SERIAL_RC="/dev/ttyS5"
-CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS6"
-CONFIG_DRIVERS_ADC_BOARD_ADC=y
-CONFIG_DRIVERS_BAROMETER_BMP388=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
-CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
-CONFIG_COMMON_DISTANCE_SENSOR=y
-CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
-CONFIG_DRIVERS_DSHOT=y
-CONFIG_DRIVERS_GPS=y
-CONFIG_DRIVERS_HEATER=y
-CONFIG_DRIVERS_IMU_INVENSENSE_IIM42653=y
-CONFIG_DRIVERS_IMU_MURATA_SCH16T=y
-CONFIG_COMMON_LIGHT=y
-CONFIG_COMMON_MAGNETOMETER=y
-CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_COMMON_RC=y
-CONFIG_DRIVERS_UAVCAN=y
-CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=2
-CONFIG_MODULES_AIRSPEED_SELECTOR=y
-CONFIG_MODULES_BATTERY_STATUS=y
-CONFIG_MODULES_COMMANDER=y
-CONFIG_MODULES_CONTROL_ALLOCATOR=y
-CONFIG_MODULES_DATAMAN=y
-CONFIG_MODULES_EKF2=y
-CONFIG_MODULES_ESC_BATTERY=y
-CONFIG_MODULES_EVENTS=y
-CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
-CONFIG_MODULES_GYRO_CALIBRATION=y
-CONFIG_MODULES_GYRO_FFT=y
-CONFIG_MODULES_LAND_DETECTOR=y
-CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
-CONFIG_MODULES_LOAD_MON=y
-CONFIG_MODULES_LOGGER=y
-CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
-CONFIG_MODULES_MANUAL_CONTROL=y
-CONFIG_MODULES_MAVLINK=y
-CONFIG_MAVLINK_DIALECT="development"
-CONFIG_MODULES_MC_ATT_CONTROL=y
-CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
-CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
-CONFIG_MODULES_MC_POS_CONTROL=y
-CONFIG_MODULES_MC_RATE_CONTROL=y
-CONFIG_MODULES_NAVIGATOR=y
-CONFIG_MODULES_RC_UPDATE=y
-CONFIG_MODULES_SENSORS=y
-CONFIG_MODULES_UXRCE_DDS_CLIENT=y
-CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
-CONFIG_SYSTEMCMDS_BSONDUMP=y
-CONFIG_SYSTEMCMDS_DMESG=y
-CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
-CONFIG_SYSTEMCMDS_I2CDETECT=y
-CONFIG_SYSTEMCMDS_LED_CONTROL=y
-CONFIG_SYSTEMCMDS_MFT=y
-CONFIG_SYSTEMCMDS_MTD=y
-CONFIG_SYSTEMCMDS_NSHTERM=y
-CONFIG_SYSTEMCMDS_PARAM=y
-CONFIG_SYSTEMCMDS_PERF=y
-CONFIG_SYSTEMCMDS_REBOOT=y
-CONFIG_SYSTEMCMDS_SD_BENCH=y
-CONFIG_SYSTEMCMDS_SD_STRESS=y
-CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
-CONFIG_SYSTEMCMDS_TOP=y
-CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
-CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
-CONFIG_SYSTEMCMDS_UORB=y
-CONFIG_SYSTEMCMDS_VER=y
-CONFIG_SYSTEMCMDS_WORK_QUEUE=y
@@ -1,13 +0,0 @@
-{
-    "board_id": 59,
-    "magic": "ARKFPVFWv1",
-    "description": "Firmware for the ARKFPV board",
-    "image": "",
-    "build_time": 0,
-    "summary": "ARKFPV",
-    "version": "0.1",
-    "image_size": 0,
-    "image_maxsize": 1835008,
-    "git_identity": "",
-    "board_revision": 0
-}
@@ -1,37 +0,0 @@
-#!/bin/sh
-#
-# board specific defaults
-#------------------------------------------------------------------------------
-
-# transision from params file to flash-based params (2022-08)
-if [ -f $PARAM_FILE ]
-then
-	param load $PARAM_FILE
-	param save
-	# create a backup
-	mv $PARAM_FILE ${PARAM_FILE}.bak
-	reboot
-fi
-
-# TODO: Tune the following parameters
-param set-default SENS_EN_THERMAL 1
-param set-default SENS_IMU_TEMP 10.0
-#param set-default SENS_IMU_TEMP_FF 0.0
-#param set-default SENS_IMU_TEMP_I 0.025
-#param set-default SENS_IMU_TEMP_P 1.0
-
-if ver hwtypecmp ARKFPV000
-then
-	param set-default SENS_TEMP_ID 3014666
-fi
-
-param set-default BAT1_V_DIV 21.0
-
-param set-default RC_CRSF_PRT_CFG 300
-param set-default RC_SBUS_PRT_CFG 0
-
-param set-default IMU_GYRO_DNF_EN 3
-
-# Single IMU
-param set-default EKF2_MULTI_IMU 0
-param set-default SENS_IMU_MODE 1
@@ -1,18 +0,0 @@
-#!/bin/sh
-#
-# ARKFPV specific board sensors init
-#------------------------------------------------------------------------------
-
-board_adc start
-
-if ver hwtypecmp ARKFPV000
-then
-	# Internal SPI bus IIM42653
-	iim42653 -R 14 -s -b 1 start
-fi
-
-# Internal magnetometer on I2C
-iis2mdc -R 0 -I -b 4 start
-
-# Internal Baro on I2C
-bmp388 -I -b 2 start
@@ -1,17 +0,0 @@
-#
-# For a description of the syntax of this configuration file,
-# see misc/tools/kconfig-language.txt.
-#
-config BOARD_HAS_PROBES
-	bool "Board provides GPIO or other Hardware for signaling to timing analyze."
-	default y
-	---help---
-		This board provides GPIO FMU-CH1-5, CAP1-6 as PROBE_1-11 to provide timing signals from selected drivers.
-
-config BOARD_USE_PROBES
-	bool "Enable the use the board provided FMU-CH1-5, CAP1-6 as PROBE_1-11"
-	default n
-	depends on BOARD_HAS_PROBES
-
-	---help---
-		Select to use GPIO FMU-CH1-5, CAP1-6  to provide timing signals from selected drivers.
@@ -1,95 +0,0 @@
-#
-# This file is autogenerated: PLEASE DO NOT EDIT IT.
-#
-# You can use "make menuconfig" to make any modifications to the installed .config file.
-# You can then do "make savedefconfig" to generate a new defconfig file that includes your
-# modifications.
-#
-# CONFIG_DEV_CONSOLE is not set
-# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
-# CONFIG_DISABLE_PTHREAD is not set
-# CONFIG_SPI_EXCHANGE is not set
-# CONFIG_STM32H7_SYSCFG is not set
-CONFIG_ARCH="arm"
-CONFIG_ARCH_BOARD_CUSTOM=y
-CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/fpv/nuttx-config"
-CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
-CONFIG_ARCH_BOARD_CUSTOM_NAME="ark"
-CONFIG_ARCH_CHIP="stm32h7"
-CONFIG_ARCH_CHIP_STM32H743II=y
-CONFIG_ARCH_CHIP_STM32H7=y
-CONFIG_ARCH_INTERRUPTSTACK=768
-CONFIG_ARMV7M_BASEPRI_WAR=y
-CONFIG_ARMV7M_ICACHE=y
-CONFIG_ARMV7M_MEMCPY=y
-CONFIG_ARMV7M_USEBASEPRI=y
-CONFIG_BOARDCTL=y
-CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
-CONFIG_BOARD_INITTHREAD_PRIORITY=254
-CONFIG_BOARD_LATE_INITIALIZE=y
-CONFIG_BOARD_LOOPSPERMSEC=95150
-CONFIG_BOARD_RESET_ON_ASSERT=2
-CONFIG_CDCACM=y
-CONFIG_CDCACM_IFLOWCONTROL=y
-CONFIG_CDCACM_PRODUCTID=0x003B
-CONFIG_CDCACM_PRODUCTSTR="ARK BL FPV.x"
-CONFIG_CDCACM_RXBUFSIZE=600
-CONFIG_CDCACM_TXBUFSIZE=12000
-CONFIG_CDCACM_VENDORID=0x3185
-CONFIG_CDCACM_VENDORSTR="ARK"
-CONFIG_DEBUG_FULLOPT=y
-CONFIG_DEBUG_SYMBOLS=y
-CONFIG_DEBUG_TCBINFO=y
-CONFIG_DEFAULT_SMALL=y
-CONFIG_EXPERIMENTAL=y
-CONFIG_FDCLONE_DISABLE=y
-CONFIG_FDCLONE_STDIO=y
-CONFIG_HAVE_CXX=y
-CONFIG_HAVE_CXXINITIALIZE=y
-CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_INIT_ENTRYPOINT="bootloader_main"
-CONFIG_INIT_STACKSIZE=3194
-CONFIG_LIBC_FLOATINGPOINT=y
-CONFIG_LIBC_LONG_LONG=y
-CONFIG_LIBC_STRERROR=y
-CONFIG_MEMSET_64BIT=y
-CONFIG_MEMSET_OPTSPEED=y
-CONFIG_PREALLOC_TIMERS=50
-CONFIG_PTHREAD_MUTEX_ROBUST=y
-CONFIG_PTHREAD_STACK_MIN=512
-CONFIG_RAM_SIZE=245760
-CONFIG_RAM_START=0x20010000
-CONFIG_RAW_BINARY=y
-CONFIG_SERIAL_TERMIOS=y
-CONFIG_SIG_DEFAULT=y
-CONFIG_SIG_SIGALRM_ACTION=y
-CONFIG_SIG_SIGUSR1_ACTION=y
-CONFIG_SIG_SIGUSR2_ACTION=y
-CONFIG_SPI=y
-CONFIG_STACK_COLORATION=y
-CONFIG_START_DAY=30
-CONFIG_START_MONTH=11
-CONFIG_STDIO_BUFFER_SIZE=32
-CONFIG_STM32H7_BKPSRAM=y
-CONFIG_STM32H7_DMA1=y
-CONFIG_STM32H7_DMA2=y
-CONFIG_STM32H7_OTGFS=y
-CONFIG_STM32H7_PROGMEM=y
-CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
-CONFIG_STM32H7_TIM1=y
-CONFIG_STM32H7_UART7=y
-CONFIG_SYSTEMTICK_HOOK=y
-CONFIG_SYSTEM_CDCACM=y
-CONFIG_TASK_NAME_SIZE=24
-CONFIG_TTY_SIGINT=y
-CONFIG_TTY_SIGINT_CHAR=0x03
-CONFIG_TTY_SIGTSTP=y
-CONFIG_UART7_RXBUFSIZE=512
-CONFIG_UART7_RXDMA=y
-CONFIG_UART7_TXBUFSIZE=512
-CONFIG_UART7_TXDMA=y
-CONFIG_USBDEV=y
-CONFIG_USBDEV_BUSPOWERED=y
-CONFIG_USBDEV_MAXPOWER=500
-CONFIG_USEC_PER_TICK=1000
@@ -1,507 +0,0 @@
-/************************************************************************************
- * nuttx-configs/px4_fmu-v6x/include/board.h
- *
- *   Copyright (C) 2016-2024 Gregory Nutt. All rights reserved.
- *   Authors: David Sidrane <david.sidrane@nscdg.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name NuttX nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ************************************************************************************/
-#ifndef __NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H
-#define __NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H
-
-/************************************************************************************
- * Included Files
- ************************************************************************************/
-
-#include "board_dma_map.h"
-
-#include <nuttx/config.h>
-
-#ifndef __ASSEMBLY__
-# include <stdint.h>
-#endif
-
-#include "stm32_rcc.h"
-#include "stm32_sdmmc.h"
-
-/************************************************************************************
- * Pre-processor Definitions
- ************************************************************************************/
-
-/* Clocking *************************************************************************/
-/* The px4_fmu-v6X  board provides the following clock sources:
- *
- *   X1: 16 MHz crystal for HSE
- *
- * So we have these clock source available within the STM32
- *
- *   HSI: 16 MHz RC factory-trimmed
- *   HSE: 16 MHz crystal for HSE
- */
-
-#define STM32_BOARD_XTAL        16000000ul
-
-#define STM32_HSI_FREQUENCY     16000000ul
-#define STM32_LSI_FREQUENCY     32000
-#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
-#define STM32_LSE_FREQUENCY     32768
-
-/* Main PLL Configuration.
- *
- * PLL source is HSE = 16,000,000
- *
- * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
- * Subject to:
- *
- *     1 <= PLLM <= 63
- *     4 <= PLLN <= 512
- *   150 MHz <= PLL_VCOL <= 420MHz
- *   192 MHz <= PLL_VCOH <= 836MHz
- *
- * SYSCLK  = PLL_VCO / PLLP
- * CPUCLK  = SYSCLK / D1CPRE
- * Subject to
- *
- *   PLLP1   = {2, 4, 6, 8, ..., 128}
- *   PLLP2,3 = {2, 3, 4, ..., 128}
- *   CPUCLK <= 480 MHz
- */
-
-#define STM32_BOARD_USEHSE
-
-#define STM32_PLLCFG_PLLSRC      RCC_PLLCKSELR_PLLSRC_HSE
-
-/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR
- *
- *   PLL1_VCO = (16,000,000 / 1) * 40 = 640 MHz
- *
- *   PLL1P = PLL1_VCO/2  = 640 MHz / 2   = 320 MHz
- *   PLL1Q = PLL1_VCO/4  = 640 MHz / 4   = 160 MHz
- *   PLL1R = PLL1_VCO/8  = 640 MHz / 8   = 80 MHz
- */
-
-#define STM32_PLLCFG_PLL1CFG    (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \
-				 RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \
-				 RCC_PLLCFGR_DIVP1EN | \
-				 RCC_PLLCFGR_DIVQ1EN | \
-				 RCC_PLLCFGR_DIVR1EN)
-#define STM32_PLLCFG_PLL1M       RCC_PLLCKSELR_DIVM1(1)
-#define STM32_PLLCFG_PLL1N       RCC_PLL1DIVR_N1(40)
-#define STM32_PLLCFG_PLL1P       RCC_PLL1DIVR_P1(2)
-#define STM32_PLLCFG_PLL1Q       RCC_PLL1DIVR_Q1(4)
-#define STM32_PLLCFG_PLL1R       RCC_PLL1DIVR_R1(8)
-
-#define STM32_VCO1_FREQUENCY     ((STM32_HSE_FREQUENCY / 1) * 40)
-#define STM32_PLL1P_FREQUENCY    (STM32_VCO1_FREQUENCY / 2)
-#define STM32_PLL1Q_FREQUENCY    (STM32_VCO1_FREQUENCY / 4)
-#define STM32_PLL1R_FREQUENCY    (STM32_VCO1_FREQUENCY / 8)
-
-/* PLL2 */
-
-#define STM32_PLLCFG_PLL2CFG     (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \
-				  RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \
-				  RCC_PLLCFGR_DIVP2EN | \
-				  RCC_PLLCFGR_DIVQ2EN | \
-				  RCC_PLLCFGR_DIVR2EN)
-#define STM32_PLLCFG_PLL2M       RCC_PLLCKSELR_DIVM2(4)
-#define STM32_PLLCFG_PLL2N       RCC_PLL2DIVR_N2(48)
-#define STM32_PLLCFG_PLL2P       RCC_PLL2DIVR_P2(2)
-#define STM32_PLLCFG_PLL2Q       RCC_PLL2DIVR_Q2(2)
-#define STM32_PLLCFG_PLL2R       RCC_PLL2DIVR_R2(2)
-
-#define STM32_VCO2_FREQUENCY     ((STM32_HSE_FREQUENCY / 4) * 48)
-#define STM32_PLL2P_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
-#define STM32_PLL2Q_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
-#define STM32_PLL2R_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
-
-/* PLL3 */
-
-#define STM32_PLLCFG_PLL3CFG    (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \
-				 RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \
-				 RCC_PLLCFGR_DIVQ3EN)
-#define STM32_PLLCFG_PLL3M      RCC_PLLCKSELR_DIVM3(4)
-#define STM32_PLLCFG_PLL3N      RCC_PLL3DIVR_N3(48)
-#define STM32_PLLCFG_PLL3P      RCC_PLL3DIVR_P3(2)
-#define STM32_PLLCFG_PLL3Q      RCC_PLL3DIVR_Q3(4)
-#define STM32_PLLCFG_PLL3R      RCC_PLL3DIVR_R3(2)
-
-#define STM32_VCO3_FREQUENCY    ((STM32_HSE_FREQUENCY / 4) * 48)
-#define STM32_PLL3P_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
-#define STM32_PLL3Q_FREQUENCY   (STM32_VCO3_FREQUENCY / 4)
-#define STM32_PLL3R_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
-
-/* SYSCLK = PLL1P = 480MHz
- * CPUCLK = SYSCLK / 1 = 480 MHz
- */
-
-#define STM32_RCC_D1CFGR_D1CPRE  (RCC_D1CFGR_D1CPRE_SYSCLK)
-#define STM32_SYSCLK_FREQUENCY   (STM32_PLL1P_FREQUENCY)
-#define STM32_CPUCLK_FREQUENCY   (STM32_SYSCLK_FREQUENCY / 1)
-
-/* Configure Clock Assignments */
-
-/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max)
- * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 160
- */
-
-#define STM32_RCC_D1CFGR_HPRE   RCC_D1CFGR_HPRE_SYSCLKd2        /* HCLK  = SYSCLK / 2 */
-#define STM32_ACLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* ACLK in D1, HCLK3 in D1 */
-#define STM32_HCLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* HCLK in D2, HCLK4 in D3 */
-#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY            /* same as above, to satisfy compiler */
-
-/* APB1 clock (PCLK1) is HCLK/2 (80 MHz) */
-
-#define STM32_RCC_D2CFGR_D2PPRE1  RCC_D2CFGR_D2PPRE1_HCLKd2       /* PCLK1 = HCLK / 2 */
-#define STM32_PCLK1_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
-
-/* APB2 clock (PCLK2) is HCLK/2 (80 MHz) */
-
-#define STM32_RCC_D2CFGR_D2PPRE2  RCC_D2CFGR_D2PPRE2_HCLKd2       /* PCLK2 = HCLK / 2 */
-#define STM32_PCLK2_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
-
-/* APB3 clock (PCLK3) is HCLK/2 (80 MHz) */
-
-#define STM32_RCC_D1CFGR_D1PPRE   RCC_D1CFGR_D1PPRE_HCLKd2        /* PCLK3 = HCLK / 2 */
-#define STM32_PCLK3_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
-
-/* APB4 clock (PCLK4) is HCLK/4 (80 MHz) */
-
-#define STM32_RCC_D3CFGR_D3PPRE   RCC_D3CFGR_D3PPRE_HCLKd2       /* PCLK4 = HCLK / 2 */
-#define STM32_PCLK4_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
-
-/* Timer clock frequencies */
-
-/* Timers driven from APB1 will be twice PCLK1 */
-
-#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
-#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
-
-/* Timers driven from APB2 will be twice PCLK2 */
-
-#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
-#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK2_FREQUENCY)
-#define STM32_APB2_TIM15_CLKIN  (2*STM32_PCLK2_FREQUENCY)
-#define STM32_APB2_TIM16_CLKIN  (2*STM32_PCLK2_FREQUENCY)
-#define STM32_APB2_TIM17_CLKIN  (2*STM32_PCLK2_FREQUENCY)
-
-/* Kernel Clock Configuration
- *
- * Note: look at Table 54 in ST Manual
- */
-
-/* I2C123 clock source */
-
-#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI
-
-/* I2C4 clock source */
-
-#define STM32_RCC_D3CCIPR_I2C4SRC    RCC_D3CCIPR_I2C4SEL_HSI
-
-/* SPI123 clock source */
-
-#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2
-
-/* SPI45 clock source */
-
-#define STM32_RCC_D2CCIP1R_SPI45SRC  RCC_D2CCIP1R_SPI45SEL_PLL2
-
-/* SPI6 clock source */
-
-#define STM32_RCC_D3CCIPR_SPI6SRC    RCC_D3CCIPR_SPI6SEL_PLL2
-
-/* USB 1 and 2 clock source */
-
-#define STM32_RCC_D2CCIP2R_USBSRC    RCC_D2CCIP2R_USBSEL_PLL3
-
-/* ADC 1 2 3 clock source */
-
-#define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2
-
-/* FDCAN 1 2 clock source */
-
-#define STM32_RCC_D2CCIP1R_FDCANSEL  RCC_D2CCIP1R_FDCANSEL_HSE   /* FDCAN 1 2 clock source */
-
-#define STM32_FDCANCLK               STM32_HSE_FREQUENCY
-
-/* FLASH wait states
- *
- *  ------------ ---------- -----------
- *  Vcore        MAX ACLK   WAIT STATES
- *  ------------ ---------- -----------
- *  1.15-1.26 V     70 MHz    0
- *  (VOS1 level)   140 MHz    1
- *                 210 MHz    2
- *  1.05-1.15 V     55 MHz    0
- *  (VOS2 level)   110 MHz    1
- *                 165 MHz    2
- *                 220 MHz    3
- *  0.95-1.05 V     45 MHz    0
- *  (VOS3 level)    90 MHz    1
- *                 135 MHz    2
- *                 180 MHz    3
- *                 225 MHz    4
- *  ------------ ---------- -----------
- */
-
-#define BOARD_FLASH_WAITSTATES 2
-
-/* SDMMC definitions ********************************************************/
-
-/* Init 400kHz, freq = PLL1Q/(2*div)  div =  PLL1Q/(2*freq) */
-
-#define STM32_SDMMC_INIT_CLKDIV     (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
-
-/* 25 MHz Max for now, 25 mHZ = PLL1Q/(2*div), div =  PLL1Q/(2*freq)
- * div = 4.8 = 240 / 50, So round up to 5 for default speed 24 MB/s
- */
-
-#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
-#  define STM32_SDMMC_MMCXFR_CLKDIV   (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
-#else
-#  define STM32_SDMMC_MMCXFR_CLKDIV   (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
-#endif
-#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
-#  define STM32_SDMMC_SDXFR_CLKDIV    (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
-#else
-#  define STM32_SDMMC_SDXFR_CLKDIV    (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
-#endif
-
-#define STM32_SDMMC_CLKCR_EDGE      STM32_SDMMC_CLKCR_NEGEDGE
-
-/* LED definitions ******************************************************************/
-/* The ARKV6X board has three, LED_GREEN a Green LED, LED_BLUE a Blue LED and
- * LED_RED a Red LED, that can be controlled by software.
- *
- * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
- * The following definitions are used to access individual LEDs.
- */
-
-/* LED index values for use with board_userled() */
-
-/* LED definitions ******************************************************************/
-/* The px4_fmu-v6x board has three, LED_GREEN a Green LED, LED_BLUE a Blue LED and
- * LED_RED a Red LED, that can be controlled by software.
- *
- * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
- * The following definitions are used to access individual LEDs.
- */
-
-/* LED index values for use with board_userled() */
-
-#define BOARD_LED1        0
-#define BOARD_LED2        1
-#define BOARD_LED3        2
-#define BOARD_NLEDS       3
-
-#define BOARD_LED_RED     BOARD_LED1
-#define BOARD_LED_GREEN   BOARD_LED2
-#define BOARD_LED_BLUE    BOARD_LED3
-
-/* LED bits for use with board_userled_all() */
-
-#define BOARD_LED1_BIT    (1 << BOARD_LED1)
-#define BOARD_LED2_BIT    (1 << BOARD_LED2)
-#define BOARD_LED3_BIT    (1 << BOARD_LED3)
-
-/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
- * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
- * events as follows:
- *
- *
- *   SYMBOL                     Meaning                      LED state
- *                                                        Red   Green Blue
- *   ----------------------  --------------------------  ------ ------ ----*/
-
-#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
-#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
-#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
-#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
-#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
-#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
-#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
-#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
-#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */
-
-/* Thus if the Green LED is statically on, NuttX has successfully booted and
- * is, apparently, running normally.  If the Red LED is flashing at
- * approximately 2Hz, then a fatal error has been detected and the system
- * has halted.
- */
-
-/* Alternate function pin selections ************************************************/
-
-#define GPIO_USART1_RX   GPIO_USART1_RX_3   /* PB7 */
-#define GPIO_USART1_TX   GPIO_USART1_TX_3   /* PB6 */
-
-#define GPIO_USART2_RX   GPIO_USART2_RX_1   /* PA3 */
-#define GPIO_USART2_TX   GPIO_USART2_TX_2   /* PD5 */
-
-#define GPIO_USART3_RX   GPIO_USART3_RX_3   /* PD9   */
-#define GPIO_USART3_TX   GPIO_USART3_TX_3   /* PD8   */
-
-#define GPIO_UART4_RX    GPIO_UART4_RX_6    /* PH14 */
-#define GPIO_UART4_TX    GPIO_UART4_TX_6    /* PH13 */
-
-#define GPIO_UART5_RX    GPIO_UART5_RX_3    /* PD2  */
-#define GPIO_UART5_TX    GPIO_UART5_TX_3    /* PC12 */
-// GPIO_UART5_RTS  No remap                 /* PC8  */
-//#define GPIO_UART5_CTS   (GPIO_ALT|GPIO_AF8|GPIO_PORTC|GPIO_PIN9|GPIO_PULLDOWN)    /* PC9  */
-
-#define GPIO_USART6_RX   GPIO_USART6_RX_1   /* PC7 */
-#define GPIO_USART6_TX   GPIO_USART6_TX_1   /* PC6  */
-
-#define GPIO_UART7_RX    GPIO_UART7_RX_4    /* PF6  */
-#define GPIO_UART7_TX    GPIO_UART7_TX_3    /* PE8  */
-#define GPIO_UART7_RTS   GPIO_UART7_RTS_2   /* PF8  */
-#define GPIO_UART7_CTS   (GPIO_UART7_CTS_1 | GPIO_PULLDOWN)   /* PE10 */
-
-
-/* CAN
- *
- * CAN1 is routed to transceiver.
- */
-#define GPIO_CAN1_RX     GPIO_CAN1_RX_3     /* PD0  */
-#define GPIO_CAN1_TX     GPIO_CAN1_TX_3     /* PD1  */
-
-/* SPI
- * SPI1 is sensors1
- * SPI2 is sensors2
- * SPI3 is sensors3
- * SPI4 is Not Used
- * SPI5 is Not Used
- * SPI6 is EXTERNAL1
- *
- */
-
-#define ADJ_SLEW_RATE(p) (((p) & ~GPIO_SPEED_MASK) | (GPIO_SPEED_2MHz))
-
-#define GPIO_SPI1_MISO   GPIO_SPI1_MISO_3               /* PG9  */
-#define GPIO_SPI1_MOSI   GPIO_SPI1_MOSI_2               /* PB5  */
-#define GPIO_SPI1_SCK    ADJ_SLEW_RATE(GPIO_SPI1_SCK_1) /* PA5  */
-
-#define GPIO_SPI6_MISO   GPIO_SPI6_MISO_2               /* PA6  */
-#define GPIO_SPI6_MOSI   GPIO_SPI6_MOSI_1               /* PG14 */
-#define GPIO_SPI6_SCK    ADJ_SLEW_RATE(GPIO_SPI6_SCK_3) /* PB3  */
-
-/* I2C
- *
- *   The optional _GPIO configurations allow the I2C driver to manually
- *   reset the bus to clear stuck slaves.  They match the pin configuration,
- *   but are normally-high GPIOs.
- *
- */
-
-#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2       /* PB8  */
-#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2       /* PB9  */
-
-#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN8)
-#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN9)
-
-#define GPIO_I2C2_SCL GPIO_I2C2_SCL_2       /* PF1 */
-#define GPIO_I2C2_SDA GPIO_I2C2_SDA_2       /* PF0 */
-
-#define GPIO_I2C2_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN1)
-#define GPIO_I2C2_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN0)
-
-#define GPIO_I2C4_SCL GPIO_I2C4_SCL_2       /* PF14 */
-#define GPIO_I2C4_SDA GPIO_I2C4_SDA_2       /* PF15 */
-
-#define GPIO_I2C4_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN14)
-#define GPIO_I2C4_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN15)
-
-/* SDMMC2
- *
- *      VDD 3.3
- *      GND
- *      SDMMC2_CK                           PD6
- *      SDMMC2_CMD                          PD7
- *      SDMMC2_D0                           PB14
- *      SDMMC2_D1                           PB15
- *      SDMMC2_D2                           PG11
- *      SDMMC2_D3                           PB4
- */
-
-#define GPIO_SDMMC2_CK   GPIO_SDMMC2_CK_1  /* PD6 */
-#define GPIO_SDMMC2_CMD  GPIO_SDMMC2_CMD_1 /* PD7 */
-//      GPIO_SDMMC2_D0   No Remap          /* PB14 */
-//      GPIO_SDMMC2_D1   No Remap          /* PB15 */
-#define GPIO_SDMMC2_D2   GPIO_SDMMC2_D2_1  /* PG11 */
-//      GPIO_SDMMC2_D3    No Remap         /* PB4 */
-
-/* USB
- *
- *      OTG_FS_DM                           PA11
- *      OTG_FS_DP                           PA12
- *      VBUS                                PA9
- */
-
-
-/* Board provides GPIO or other Hardware for signaling to timing analyzer */
-
-#if defined(CONFIG_BOARD_USE_PROBES)
-# include "stm32_gpio.h"
-# define PROBE_N(n) (1<<((n)-1))
-# define PROBE_1    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTI|GPIO_PIN0)   /* PI0 AUX1 */
-# define PROBE_2    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN12)  /* PH12 AUX2 */
-# define PROBE_3    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN11)  /* PH11 AUX3 */
-# define PROBE_4    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN10)  /* PH10 AUX4 */
-# define PROBE_5    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13)  /* PD13 AUX5 */
-# define PROBE_6    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14)  /* PD14 AUX6 */
-# define PROBE_7    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN6)   /* PH6  AUX7 */
-# define PROBE_8    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN9)   /* PH9  AUX8 */
-
-# define PROBE_INIT(mask) \
-	do { \
-		if ((mask)& PROBE_N(1)) { stm32_configgpio(PROBE_1); } \
-		if ((mask)& PROBE_N(2)) { stm32_configgpio(PROBE_2); } \
-		if ((mask)& PROBE_N(3)) { stm32_configgpio(PROBE_3); } \
-		if ((mask)& PROBE_N(4)) { stm32_configgpio(PROBE_4); } \
-		if ((mask)& PROBE_N(5)) { stm32_configgpio(PROBE_5); } \
-		if ((mask)& PROBE_N(6)) { stm32_configgpio(PROBE_6); } \
-		if ((mask)& PROBE_N(7)) { stm32_configgpio(PROBE_7); } \
-		if ((mask)& PROBE_N(8)) { stm32_configgpio(PROBE_8); } \
-		if ((mask)& PROBE_N(9)) { stm32_configgpio(PROBE_9); } \
-	} while(0)
-
-# define PROBE(n,s)  do {stm32_gpiowrite(PROBE_##n,(s));}while(0)
-# define PROBE_MARK(n) PROBE(n,false);PROBE(n,true)
-#else
-# define PROBE_INIT(mask)
-# define PROBE(n,s)
-# define PROBE_MARK(n)
-#endif
-
-#endif  /*__NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H  */
@@ -1,108 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2024 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#pragma once
-
-// DMAMUX1 Using at most 8 Channels on DMA1 --------   Assigned
-//                                                     V
-
-// Timer 4 Channel 1                               /* DMA1:29 TIM4CH1 */
-
-#define DMAMAP_SPI1_RX    DMAMAP_DMA12_SPI1RX_0   /* 1 DMA1:37 IIM-42653 */
-#define DMAMAP_SPI1_TX    DMAMAP_DMA12_SPI1TX_0   /* 2 DMA1:38 IIM-42653 */
-
-//#define DMAMAP_SPI2_RX    DMAMAP_DMA12_SPI2RX_0  /* 3 DMA1:39 ICM-42688-P */
-//#define DMAMAP_SPI2_TX    DMAMAP_DMA12_SPI2TX_0  /* 4 DMA1:40 ICM-42688-P */
-
-#define DMAMAP_USART1_RX  DMAMAP_DMA12_USART1RX_0 /*  DMA1:41  GPS1 */
-#define DMAMAP_USART1_TX  DMAMAP_DMA12_USART1TX_0 /*  DMA1:42  GPS1 */
-
-//#define DMAMAP_USART3_RX  DMAMAP_DMA12_USART3RX_0 /*  DMA1:45 DEBUG */
-//#define DMAMAP_USART3_TX  DMAMAP_DMA12_USART3TX_0 /*  DMA1:46 DEBUG */
-
-// Timer 8 Channel 1                               /* DMA1:47 TIM8CH1 */
-// Timer 8 Channel 2                               /* DMA1:48 TIM8CH2 */
-// Timer 8 Channel 3                               /* DMA1:49 TIM8CH3 */
-// Timer 8 Channel 4                               /* DMA1:50 TIM8CH4 */
-
-// Timer 5 Channel 1                               /* DMA1:55 TIM5CH1 */
-// Timer 5 Channel 2                               /* DMA1:56 TIM5CH2 */
-// Timer 5 Channel 3                               /* DMA1:57 TIM5CH3 */
-// Timer 5 Channel 4                               /* DMA1:58 TIM5CH4 */
-
-// #define DMAMAP_UART4_RX   DMAMAP_DMA12_UART4RX_0  /*  DMA1:63 UART4 */
-// #define DMAMAP_UART4_TX   DMAMAP_DMA12_UART4TX_0  /*  DMA1:64 UART4 */
-
-#define DMAMAP_USART6_RX  DMAMAP_DMA12_USART6RX_0 /* 5 DMA1:71 RC */
-// #define DMAMAP_USART6_TX  DMAMAP_DMA12_USART6TX_0 /* 6 DMA1:72 RC */
-
-// Assigned in timer_config.cpp
-
-// Timer 4                                          /* 7 DMA1:32 TIM4UP */
-// Timer 5                                          /* 8 DMA1:50 TIM5UP */
-
-// DMAMUX2 Using at most 8 Channels on DMA2 --------   Assigned
-//                                                     V
-
-// Timer 4 Channel 1                               /* DMA2:29 TIM4CH1 */
-
-#define DMAMAP_USART2_RX  DMAMAP_DMA12_USART2RX_1   /* 3 DMA2:43 TELEM3 */
-#define DMAMAP_USART2_TX  DMAMAP_DMA12_USART2TX_1   /* 4 DMA2:44 TELEM3 */
-
-#define DMAMAP_USART3_RX  DMAMAP_DMA12_USART3RX_1   /* 3 DMA2:45 DEBUG */
-#define DMAMAP_USART3_TX  DMAMAP_DMA12_USART3TX_1   /* 4 DMA2:46 DEBUG */
-
-// Timer 8 Channel 1                                 /* DMA2:47 TIM8CH1 */
-// Timer 8 Channel 2                                 /* DMA2:48 TIM8CH2 */
-// Timer 8 Channel 3                                 /* DMA2:49 TIM8CH3 */
-// Timer 8 Channel 4                                 /* DMA2:50 TIM8CH4 */
-
-// Timer 5 Channel 1                                 /* DMA2:55 TIM5CH1 */
-// Timer 5 Channel 2                                 /* DMA2:56 TIM5CH2 */
-// Timer 5 Channel 3                                 /* DMA2:57 TIM5CH3 */
-// Timer 5 Channel 4                                 /* DMA2:58 TIM5CH4 */
-
-//#define DMAMAP_SPI3_RX    DMAMAP_DMA12_SPI3RX_1     /* 1 DMA2:61 BMI088 */
-//#define DMAMAP_SPI3_TX    DMAMAP_DMA12_SPI3TX_1     /* 2 DMA2:62 BMI088 */
-
-#define DMAMAP_UART5_RX   DMAMAP_DMA12_UART5RX_1    /* 5 DMA2:65 TELEM2 */
-#define DMAMAP_UART5_TX   DMAMAP_DMA12_UART5TX_1    /* 6 DMA2:66 TELEM2 */
-
-#define DMAMAP_UART7_RX   DMAMAP_DMA12_UART7RX_1    /* 7 DMA1:79 TELEM1 */
-#define DMAMAP_UART7_TX   DMAMAP_DMA12_UART7TX_1    /* 8 DMA1:80 TELEM1 */
-
-// DMAMUX2 Using at most 8 Channels on BDMA --------   Assigned
-//                                                     V
-
-#define DMAMAP_SPI6_RX    DMAMAP_BDMA_SPI6_RX       /* 1 BDMA:11 SPI J11 */
-#define DMAMAP_SPI6_TX    DMAMAP_BDMA_SPI6_TX       /* 2 BDMA:12 SPI J11 */
@@ -1,279 +0,0 @@
-#
-# This file is autogenerated: PLEASE DO NOT EDIT IT.
-#
-# You can use "make menuconfig" to make any modifications to the installed .config file.
-# You can then do "make savedefconfig" to generate a new defconfig file that includes your
-# modifications.
-#
-# CONFIG_DISABLE_ENVIRON is not set
-# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
-# CONFIG_DISABLE_PTHREAD is not set
-# CONFIG_MMCSD_HAVE_CARDDETECT is not set
-# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
-# CONFIG_MMCSD_MMCSUPPORT is not set
-# CONFIG_MMCSD_SPI is not set
-# CONFIG_NSH_DISABLEBG is not set
-# CONFIG_NSH_DISABLESCRIPT is not set
-# CONFIG_NSH_DISABLE_CAT is not set
-# CONFIG_NSH_DISABLE_CD is not set
-# CONFIG_NSH_DISABLE_CP is not set
-# CONFIG_NSH_DISABLE_DATE is not set
-# CONFIG_NSH_DISABLE_DF is not set
-# CONFIG_NSH_DISABLE_ECHO is not set
-# CONFIG_NSH_DISABLE_ENV is not set
-# CONFIG_NSH_DISABLE_EXEC is not set
-# CONFIG_NSH_DISABLE_EXPORT is not set
-# CONFIG_NSH_DISABLE_FREE is not set
-# CONFIG_NSH_DISABLE_GET is not set
-# CONFIG_NSH_DISABLE_HELP is not set
-# CONFIG_NSH_DISABLE_IFCONFIG is not set
-# CONFIG_NSH_DISABLE_IFUPDOWN is not set
-# CONFIG_NSH_DISABLE_ITEF is not set
-# CONFIG_NSH_DISABLE_KILL is not set
-# CONFIG_NSH_DISABLE_LOOPS is not set
-# CONFIG_NSH_DISABLE_LS is not set
-# CONFIG_NSH_DISABLE_MKDIR is not set
-# CONFIG_NSH_DISABLE_MKFATFS is not set
-# CONFIG_NSH_DISABLE_MOUNT is not set
-# CONFIG_NSH_DISABLE_MV is not set
-# CONFIG_NSH_DISABLE_PS is not set
-# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set
-# CONFIG_NSH_DISABLE_PWD is not set
-# CONFIG_NSH_DISABLE_RM is not set
-# CONFIG_NSH_DISABLE_RMDIR is not set
-# CONFIG_NSH_DISABLE_SEMICOLON is not set
-# CONFIG_NSH_DISABLE_SET is not set
-# CONFIG_NSH_DISABLE_SLEEP is not set
-# CONFIG_NSH_DISABLE_SOURCE is not set
-# CONFIG_NSH_DISABLE_TELNETD is not set
-# CONFIG_NSH_DISABLE_TEST is not set
-# CONFIG_NSH_DISABLE_TIME is not set
-# CONFIG_NSH_DISABLE_UMOUNT is not set
-# CONFIG_NSH_DISABLE_UNSET is not set
-# CONFIG_NSH_DISABLE_USLEEP is not set
-CONFIG_ARCH="arm"
-CONFIG_ARCH_BOARD_CUSTOM=y
-CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/fpv/nuttx-config"
-CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
-CONFIG_ARCH_BOARD_CUSTOM_NAME="ark"
-CONFIG_ARCH_CHIP="stm32h7"
-CONFIG_ARCH_CHIP_STM32H743II=y
-CONFIG_ARCH_CHIP_STM32H7=y
-CONFIG_ARCH_INTERRUPTSTACK=768
-CONFIG_ARCH_STACKDUMP=y
-CONFIG_ARMV7M_BASEPRI_WAR=y
-CONFIG_ARMV7M_DCACHE=y
-CONFIG_ARMV7M_DTCM=y
-CONFIG_ARMV7M_ICACHE=y
-CONFIG_ARMV7M_MEMCPY=y
-CONFIG_ARMV7M_USEBASEPRI=y
-CONFIG_ARM_MPU_EARLY_RESET=y
-CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
-CONFIG_BOARD_CRASHDUMP=y
-CONFIG_BOARD_LOOPSPERMSEC=95751
-CONFIG_BOARD_RESET_ON_ASSERT=2
-CONFIG_BUILTIN=y
-CONFIG_CDCACM=y
-CONFIG_CDCACM_IFLOWCONTROL=y
-CONFIG_CDCACM_PRODUCTID=0x003B
-CONFIG_CDCACM_PRODUCTSTR="ARK FPV.x"
-CONFIG_CDCACM_RXBUFSIZE=600
-CONFIG_CDCACM_TXBUFSIZE=12000
-CONFIG_CDCACM_VENDORID=0x3185
-CONFIG_CDCACM_VENDORSTR="ARK"
-CONFIG_DEBUG_FULLOPT=y
-CONFIG_DEBUG_HARDFAULT_ALERT=y
-CONFIG_DEBUG_MEMFAULT=y
-CONFIG_DEBUG_SYMBOLS=y
-CONFIG_DEBUG_TCBINFO=y
-CONFIG_DEFAULT_SMALL=y
-CONFIG_DEV_FIFO_SIZE=0
-CONFIG_DEV_PIPE_MAXSIZE=1024
-CONFIG_DEV_PIPE_SIZE=70
-CONFIG_EXPERIMENTAL=y
-CONFIG_FAT_DMAMEMORY=y
-CONFIG_FAT_LCNAMES=y
-CONFIG_FAT_LFN=y
-CONFIG_FAT_LFN_ALIAS_HASH=y
-CONFIG_FDCLONE_STDIO=y
-CONFIG_FS_BINFS=y
-CONFIG_FS_CROMFS=y
-CONFIG_FS_FAT=y
-CONFIG_FS_FATTIME=y
-CONFIG_FS_PROCFS=y
-CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
-CONFIG_FS_PROCFS_MAX_TASKS=64
-CONFIG_FS_PROCFS_REGISTER=y
-CONFIG_FS_ROMFS=y
-CONFIG_GRAN=y
-CONFIG_GRAN_INTR=y
-CONFIG_HAVE_CXX=y
-CONFIG_HAVE_CXXINITIALIZE=y
-CONFIG_I2C=y
-CONFIG_I2C_RESET=y
-CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_INIT_ENTRYPOINT="nsh_main"
-CONFIG_INIT_STACKSIZE=3194
-CONFIG_LIBC_FLOATINGPOINT=y
-CONFIG_LIBC_LONG_LONG=y
-CONFIG_LIBC_MAX_EXITFUNS=1
-CONFIG_LIBC_STRERROR=y
-CONFIG_MEMSET_64BIT=y
-CONFIG_MEMSET_OPTSPEED=y
-CONFIG_MMCSD=y
-CONFIG_MMCSD_SDIO=y
-CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y
-CONFIG_MM_REGIONS=4
-CONFIG_MTD=y
-CONFIG_MTD_BYTE_WRITE=y
-CONFIG_MTD_PARTITION=y
-CONFIG_MTD_PROGMEM=y
-CONFIG_MTD_RAMTRON=y
-CONFIG_NAME_MAX=40
-CONFIG_NSH_ARCHINIT=y
-CONFIG_NSH_ARGCAT=y
-CONFIG_NSH_BUILTIN_APPS=y
-CONFIG_NSH_CMDPARMS=y
-CONFIG_NSH_CROMFSETC=y
-CONFIG_NSH_LINELEN=128
-CONFIG_NSH_MAXARGUMENTS=15
-CONFIG_NSH_NESTDEPTH=8
-CONFIG_NSH_QUOTE=y
-CONFIG_NSH_ROMFSETC=y
-CONFIG_NSH_ROMFSSECTSIZE=128
-CONFIG_NSH_STRERROR=y
-CONFIG_NSH_VARS=y
-CONFIG_OTG_ID_GPIO_DISABLE=y
-CONFIG_PIPES=y
-CONFIG_PREALLOC_TIMERS=50
-CONFIG_PRIORITY_INHERITANCE=y
-CONFIG_PTHREAD_MUTEX_ROBUST=y
-CONFIG_PTHREAD_STACK_MIN=512
-CONFIG_RAMTRON_EMULATE_PAGE_SHIFT=5
-CONFIG_RAMTRON_EMULATE_SECTOR_SHIFT=5
-CONFIG_RAMTRON_SETSPEED=y
-CONFIG_RAM_SIZE=245760
-CONFIG_RAM_START=0x20010000
-CONFIG_RAW_BINARY=y
-CONFIG_READLINE_CMD_HISTORY=y
-CONFIG_READLINE_TABCOMPLETION=y
-CONFIG_RTC_DATETIME=y
-CONFIG_SCHED_HPWORK=y
-CONFIG_SCHED_HPWORKPRIORITY=249
-CONFIG_SCHED_HPWORKSTACKSIZE=1280
-CONFIG_SCHED_INSTRUMENTATION=y
-CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
-CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
-CONFIG_SCHED_LPWORK=y
-CONFIG_SCHED_LPWORKPRIORITY=50
-CONFIG_SCHED_LPWORKSTACKSIZE=1632
-CONFIG_SCHED_WAITPID=y
-CONFIG_SDMMC2_SDIO_PULLUP=y
-CONFIG_SEM_PREALLOCHOLDERS=32
-CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
-CONFIG_SERIAL_TERMIOS=y
-CONFIG_SIG_DEFAULT=y
-CONFIG_SIG_SIGALRM_ACTION=y
-CONFIG_SIG_SIGUSR1_ACTION=y
-CONFIG_SIG_SIGUSR2_ACTION=y
-CONFIG_SIG_SIGWORK=4
-CONFIG_STACK_COLORATION=y
-CONFIG_START_DAY=30
-CONFIG_START_MONTH=11
-CONFIG_STDIO_BUFFER_SIZE=256
-CONFIG_STM32H7_ADC1=y
-CONFIG_STM32H7_ADC3=y
-CONFIG_STM32H7_BBSRAM=y
-CONFIG_STM32H7_BBSRAM_FILES=5
-CONFIG_STM32H7_BDMA=y
-CONFIG_STM32H7_BKPSRAM=y
-CONFIG_STM32H7_DMA1=y
-CONFIG_STM32H7_DMA2=y
-CONFIG_STM32H7_DMACAPABLE=y
-CONFIG_STM32H7_FLASH_OVERRIDE_I=y
-CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
-CONFIG_STM32H7_I2C1=y
-CONFIG_STM32H7_I2C2=y
-CONFIG_STM32H7_I2C4=y
-CONFIG_STM32H7_I2C_DYNTIMEO=y
-CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
-CONFIG_STM32H7_OTGFS=y
-CONFIG_STM32H7_PROGMEM=y
-CONFIG_STM32H7_RTC=y
-CONFIG_STM32H7_RTC_AUTO_LSECLOCK_START_DRV_CAPABILITY=y
-CONFIG_STM32H7_RTC_MAGIC_REG=1
-CONFIG_STM32H7_SAVE_CRASHDUMP=y
-CONFIG_STM32H7_SDMMC2=y
-CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
-CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
-CONFIG_STM32H7_SPI1=y
-CONFIG_STM32H7_SPI1_DMA=y
-CONFIG_STM32H7_SPI1_DMA_BUFFER=1024
-CONFIG_STM32H7_SPI6=y
-CONFIG_STM32H7_SPI6_DMA=y
-CONFIG_STM32H7_SPI6_DMA_BUFFER=1024
-CONFIG_STM32H7_TIM1=y
-CONFIG_STM32H7_TIM2=y
-CONFIG_STM32H7_TIM3=y
-CONFIG_STM32H7_TIM4=y
-CONFIG_STM32H7_TIM5=y
-CONFIG_STM32H7_TIM8=y
-CONFIG_STM32H7_TIM12=y
-CONFIG_STM32H7_UART4=y
-CONFIG_STM32H7_UART5=y
-CONFIG_STM32H7_UART7=y
-CONFIG_STM32H7_USART1=y
-CONFIG_STM32H7_USART2=y
-CONFIG_STM32H7_USART3=y
-CONFIG_STM32H7_USART6=y
-CONFIG_STM32H7_USART_BREAKS=y
-CONFIG_STM32H7_USART_INVERT=y
-CONFIG_STM32H7_USART_SINGLEWIRE=y
-CONFIG_STM32H7_USART_SWAP=y
-CONFIG_SYSTEM_CDCACM=y
-CONFIG_SYSTEM_NSH=y
-CONFIG_TASK_NAME_SIZE=24
-CONFIG_UART4_BAUD=57600
-CONFIG_UART4_RXBUFSIZE=600
-CONFIG_UART4_TXBUFSIZE=1500
-CONFIG_UART5_IFLOWCONTROL=y
-CONFIG_UART5_OFLOWCONTROL=y
-CONFIG_UART5_RXDMA=y
-CONFIG_UART5_RXBUFSIZE=600
-CONFIG_UART5_TXBUFSIZE=10000
-CONFIG_UART5_TXDMA=y
-CONFIG_UART7_BAUD=57600
-CONFIG_UART7_IFLOWCONTROL=y
-CONFIG_UART7_OFLOWCONTROL=y
-CONFIG_UART7_RXBUFSIZE=600
-CONFIG_UART7_RXDMA=y
-CONFIG_UART7_TXBUFSIZE=3000
-CONFIG_UART7_TXDMA=y
-CONFIG_USART1_BAUD=57600
-CONFIG_USART1_RXDMA=y
-CONFIG_USART1_TXDMA=y
-CONFIG_USART1_RXBUFSIZE=600
-CONFIG_USART1_TXBUFSIZE=1500
-CONFIG_USART2_BAUD=57600
-CONFIG_USART2_RXDMA=y
-CONFIG_USART2_TXDMA=y
-CONFIG_USART2_RXBUFSIZE=600
-CONFIG_USART2_TXBUFSIZE=1500
-CONFIG_USART3_BAUD=57600
-CONFIG_USART3_RXBUFSIZE=180
-CONFIG_USART3_RXDMA=y
-CONFIG_USART3_SERIAL_CONSOLE=y
-CONFIG_USART3_TXBUFSIZE=1500
-CONFIG_USART3_TXDMA=y
-CONFIG_USART6_BAUD=57600
-CONFIG_USART6_RXDMA=y
-CONFIG_USART6_RXBUFSIZE=600
-CONFIG_USART6_TXBUFSIZE=1500
-CONFIG_USART6_RXBUFSIZE=600
-CONFIG_USART6_TXBUFSIZE=1500
-CONFIG_USBDEV=y
-CONFIG_USBDEV_BUSPOWERED=y
-CONFIG_USBDEV_MAXPOWER=500
-CONFIG_USEC_PER_TICK=1000
-CONFIG_WATCHDOG=y
@@ -1,215 +0,0 @@
-/****************************************************************************
- * scripts/script.ld
- *
- *   Copyright (C) 2016, 2024 Gregory Nutt. All rights reserved.
- *   Author: Gregory Nutt <gnutt@nuttx.org>
- *
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name NuttX nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/* The ARKV6X uses an STM32H743II has 2048Kb of main FLASH memory.
- * The flash memory is partitioned into a User Flash memory and a System
- * Flash memory. Each of these memories has two banks:
- *
- *   1) User Flash memory:
- *
- *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
- *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
- *
- *   2) System Flash memory:
- *
- *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
- *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
- *
- *   3) User option bytes for user configuration, only in Bank 1.
- *
- * In the STM32H743II, two different boot spaces can be selected through
- * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
- * BOOT_ADD1 option bytes:
- *
- *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
- *      ST programmed value: Flash memory at 0x0800:0000
- *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
- *      ST programmed value: System bootloader at 0x1FF0:0000
- *
- * The ARKV6X has a test point on board, the BOOT0 pin is at ground so by
- * default, the STM32 will boot to address 0x0800:0000 in FLASH unless the test
- * point is pulled to 3.3V.then the boot will be from 0x1FF0:0000
- *
- * The STM32H743II also has 1024Kb of data SRAM.
- * SRAM is split up into several blocks and into three power domains:
- *
- *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
- *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
- *
- *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
- *
- *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
- *           DTCM ports. The DTCM-RAM could be used for critical real-time
- *           data, such as interrupt service routines or stack / heap memory.
- *           Both DTCM-RAMs can be used in parallel (for load/store operations)
- *           thanks to the Cortex-M7 dual issue capability.
- *
- *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
- *
- *           This RAM is connected to ITCM 64-bit interface designed for
- *           execution of critical real-times routines by the CPU.
- *
- *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
- *      through D1 domain AXI bus matrix
- *
- *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
- *
- *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
- *      through D2 domain AHB bus matrix
- *
- *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
- *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
- *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
- *
- *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
- *
- *   4) AHB SRAM (D3 domain) accessible by most of system masters
- *      through D3 domain AHB bus matrix
- *
- *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
- *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
- *
- * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
- * where the code expects to begin execution by jumping to the entry point in
- * the 0x0800:0000 address range.
- *
- * The bootloader uses the first sector of the flash, which is 128K in length.
- */
-
-MEMORY
-{
-	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
-	flash (rx)  : ORIGIN = 0x08000000, LENGTH =  128K
-	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
-	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
-	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
-	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
-	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
-	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
-	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
-	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
-}
-
-OUTPUT_ARCH(arm)
-EXTERN(_vectors)
-ENTRY(_stext)
-
-/*
- * Ensure that abort() is present in the final object.  The exception handling
- * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
- */
-EXTERN(abort)
-EXTERN(_bootdelay_signature)
-
-SECTIONS
-{
-	.text : {
-		_stext = ABSOLUTE(.);
-		*(.vectors)
-		. = ALIGN(32);
-		/*
-		This signature provides the bootloader with a way to delay booting
-		*/
-		_bootdelay_signature = ABSOLUTE(.);
-		FILL(0xffecc2925d7d05c5)
-		. += 8;
-		*(.text .text.*)
-		*(.fixup)
-		*(.gnu.warning)
-		*(.rodata .rodata.*)
-		*(.gnu.linkonce.t.*)
-		*(.glue_7)
-		*(.glue_7t)
-		*(.got)
-		*(.gcc_except_table)
-		*(.gnu.linkonce.r.*)
-		_etext = ABSOLUTE(.);
-
-	} > flash
-
-	/*
-	 * Init functions (static constructors and the like)
-	 */
-	.init_section : {
-		_sinit = ABSOLUTE(.);
-		KEEP(*(.init_array .init_array.*))
-		_einit = ABSOLUTE(.);
-	} > flash
-
-
-	.ARM.extab : {
-		*(.ARM.extab*)
-	} > flash
-
-	__exidx_start = ABSOLUTE(.);
-	.ARM.exidx : {
-		*(.ARM.exidx*)
-	} > flash
-	__exidx_end = ABSOLUTE(.);
-
-	_eronly = ABSOLUTE(.);
-
-	.data : {
-		_sdata = ABSOLUTE(.);
-		*(.data .data.*)
-		*(.gnu.linkonce.d.*)
-		CONSTRUCTORS
-		_edata = ABSOLUTE(.);
-	} > sram AT > flash
-
-	.bss : {
-		_sbss = ABSOLUTE(.);
-		*(.bss .bss.*)
-		*(.gnu.linkonce.b.*)
-		*(COMMON)
-		. = ALIGN(4);
-		_ebss = ABSOLUTE(.);
-	} > sram
-
-	/* Stabs debugging sections. */
-	.stab 0 : { *(.stab) }
-	.stabstr 0 : { *(.stabstr) }
-	.stab.excl 0 : { *(.stab.excl) }
-	.stab.exclstr 0 : { *(.stab.exclstr) }
-	.stab.index 0 : { *(.stab.index) }
-	.stab.indexstr 0 : { *(.stab.indexstr) }
-	.comment 0 : { *(.comment) }
-	.debug_abbrev 0 : { *(.debug_abbrev) }
-	.debug_info 0 : { *(.debug_info) }
-	.debug_line 0 : { *(.debug_line) }
-	.debug_pubnames 0 : { *(.debug_pubnames) }
-	.debug_aranges 0 : { *(.debug_aranges) }
-}
@@ -1,229 +0,0 @@
-/****************************************************************************
- * scripts/script.ld
- *
- *   Copyright (C) 2016, 2024 Gregory Nutt. All rights reserved.
- *   Author: Gregory Nutt <gnutt@nuttx.org>
- *
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name NuttX nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/* The ARKV6X uses an STM32H743II has 2048Kb of main FLASH memory.
- * The flash memory is partitioned into a User Flash memory and a System
- * Flash memory. Each of these memories has two banks:
- *
- *   1) User Flash memory:
- *
- *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
- *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
- *
- *   2) System Flash memory:
- *
- *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
- *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
- *
- *   3) User option bytes for user configuration, only in Bank 1.
- *
- * In the STM32H743II, two different boot spaces can be selected through
- * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
- * BOOT_ADD1 option bytes:
- *
- *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
- *      ST programmed value: Flash memory at 0x0800:0000
- *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
- *      ST programmed value: System bootloader at 0x1FF0:0000
- *
- * The ARKV6X has a test point on board, the BOOT0 pin is at ground so by
- * default, the STM32 will boot to address 0x0800:0000 in FLASH unless the test
- * point is pulled to 3.3V.then the boot will be from 0x1FF0:0000
- *
- * The STM32H743II also has 1024Kb of data SRAM.
- * SRAM is split up into several blocks and into three power domains:
- *
- *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
- *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
- *
- *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
- *
- *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
- *           DTCM ports. The DTCM-RAM could be used for critical real-time
- *           data, such as interrupt service routines or stack / heap memory.
- *           Both DTCM-RAMs can be used in parallel (for load/store operations)
- *           thanks to the Cortex-M7 dual issue capability.
- *
- *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
- *
- *           This RAM is connected to ITCM 64-bit interface designed for
- *           execution of critical real-times routines by the CPU.
- *
- *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
- *      through D1 domain AXI bus matrix
- *
- *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
- *
- *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
- *      through D2 domain AHB bus matrix
- *
- *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
- *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
- *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
- *
- *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
- *
- *   4) AHB SRAM (D3 domain) accessible by most of system masters
- *      through D3 domain AHB bus matrix
- *
- *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
- *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
- *
- * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
- * where the code expects to begin execution by jumping to the entry point in
- * the 0x0800:0000 address range.
- */
-
-MEMORY
-{
-	ITCM_RAM  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
-	FLASH      (rx) : ORIGIN = 0x08020000, LENGTH = 1792K /* params in last sector */
-
-	DTCM1_RAM (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
-	DTCM2_RAM (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
-	AXI_SRAM  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K /* D1 domain AXI bus */
-	SRAM1     (rwx) : ORIGIN = 0x30000000, LENGTH =  128K /* D2 domain AHB bus */
-	SRAM2     (rwx) : ORIGIN = 0x30020000, LENGTH =  128K /* D2 domain AHB bus */
-	SRAM3     (rwx) : ORIGIN = 0x30040000, LENGTH =   32K /* D2 domain AHB bus */
-	SRAM4     (rwx) : ORIGIN = 0x38000000, LENGTH =   64K /* D3 domain */
-	BKPRAM    (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
-}
-
-OUTPUT_ARCH(arm)
-EXTERN(_vectors)
-ENTRY(_stext)
-
-/*
- * Ensure that abort() is present in the final object.  The exception handling
- * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
- */
-EXTERN(abort)
-EXTERN(_bootdelay_signature)
-EXTERN(board_get_manifest)
-
-SECTIONS
-{
-	.text : {
-		_stext = ABSOLUTE(.);
-		*(.vectors)
-		. = ALIGN(32);
-		/*
-		This signature provides the bootloader with a way to delay booting
-		*/
-		_bootdelay_signature = ABSOLUTE(.);
-		FILL(0xffecc2925d7d05c5)
-		. += 8;
-		*(.text .text.*)
-		*(.fixup)
-		*(.gnu.warning)
-		*(.rodata .rodata.*)
-		*(.gnu.linkonce.t.*)
-		*(.glue_7)
-		*(.glue_7t)
-		*(.got)
-		*(.gcc_except_table)
-		*(.gnu.linkonce.r.*)
-		_etext = ABSOLUTE(.);
-
-	} > FLASH
-
-	/*
-	 * Init functions (static constructors and the like)
-	 */
-	.init_section : {
-		_sinit = ABSOLUTE(.);
-		KEEP(*(.init_array .init_array.*))
-		_einit = ABSOLUTE(.);
-	} > FLASH
-
-
-	.ARM.extab : {
-		*(.ARM.extab*)
-	} > FLASH
-
-	__exidx_start = ABSOLUTE(.);
-	.ARM.exidx : {
-		*(.ARM.exidx*)
-	} > FLASH
-	__exidx_end = ABSOLUTE(.);
-
-	_eronly = ABSOLUTE(.);
-
-	.data : {
-		_sdata = ABSOLUTE(.);
-		*(.data .data.*)
-		*(.gnu.linkonce.d.*)
-		CONSTRUCTORS
-		_edata = ABSOLUTE(.);
-
-		/* Pad out last section as the STM32H7 Flash write size is 256 bits. 32 bytes */
-		. = ALIGN(16);
-		FILL(0xffff)
-		. += 16;
-	} > AXI_SRAM AT > FLASH  = 0xffff
-
-	.bss : {
-		_sbss = ABSOLUTE(.);
-		*(.bss .bss.*)
-		*(.gnu.linkonce.b.*)
-		*(COMMON)
-		. = ALIGN(4);
-		_ebss = ABSOLUTE(.);
-	} > AXI_SRAM
-
-	/* Emit the the D3 power domain section for locating BDMA data */
-
-	.sram4_reserve (NOLOAD) :
-	{
-		*(.sram4)
-		. = ALIGN(4);
-		_sram4_heap_start = ABSOLUTE(.);
-	} > SRAM4
-
-	/* Stabs debugging sections. */
-	.stab 0 : { *(.stab) }
-	.stabstr 0 : { *(.stabstr) }
-	.stab.excl 0 : { *(.stab.excl) }
-	.stab.exclstr 0 : { *(.stab.exclstr) }
-	.stab.index 0 : { *(.stab.index) }
-	.stab.indexstr 0 : { *(.stab.indexstr) }
-	.comment 0 : { *(.comment) }
-	.debug_abbrev 0 : { *(.debug_abbrev) }
-	.debug_info 0 : { *(.debug_info) }
-	.debug_line 0 : { *(.debug_line) }
-	.debug_pubnames 0 : { *(.debug_pubnames) }
-	.debug_aranges 0 : { *(.debug_aranges) }
-}
@@ -1,77 +0,0 @@
-############################################################################
-#
-#   Copyright (c) 2016 PX4 Development Team. All rights reserved.
-#
-# Redistribution and use in source and binary forms, with or without
-# modification, are permitted provided that the following conditions
-# are met:
-#
-# 1. Redistributions of source code must retain the above copyright
-#    notice, this list of conditions and the following disclaimer.
-# 2. Redistributions in binary form must reproduce the above copyright
-#    notice, this list of conditions and the following disclaimer in
-#    the documentation and/or other materials provided with the
-#    distribution.
-# 3. Neither the name PX4 nor the names of its contributors may be
-#    used to endorse or promote products derived from this software
-#    without specific prior written permission.
-#
-# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
-# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
-# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
-# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
-# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
-# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
-# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
-# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-# POSSIBILITY OF SUCH DAMAGE.
-#
-############################################################################
-if("${PX4_BOARD_LABEL}" STREQUAL  "bootloader")
-	add_compile_definitions(BOOTLOADER)
-	add_library(drivers_board
-		bootloader_main.c
-		init.c
-		usb.c
-		timer_config.cpp
-	)
-	target_link_libraries(drivers_board
-		PRIVATE
-			nuttx_arch # sdio
-			nuttx_drivers # sdio
-			px4_layer #gpio
-			arch_io_pins # iotimer
-			bootloader
-	)
-	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common)
-
-else()
-	add_library(drivers_board
-		can.c
-		i2c.cpp
-		init.c
-		led.c
-		mtd.cpp
-		sdio.c
-		spi.cpp
-		spix_sync.c
-		spix_sync.h
-		timer_config.cpp
-		usb.c
-	)
-	add_dependencies(drivers_board arch_board_hw_info)
-
-	target_link_libraries(drivers_board
-		PRIVATE
-			arch_io_pins
-			arch_spi
-			arch_board_hw_info
-			drivers__led # drv_led_start
-			nuttx_arch # sdio
-			nuttx_drivers # sdio
-			px4_layer
-	)
-endif()
@@ -1,397 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2016-2024 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file board_config.h
- *
- * ARK FPV internal definitions
- */
-
-#pragma once
-
-/****************************************************************************************************
- * Included Files
- ****************************************************************************************************/
-
-#include <px4_platform_common/px4_config.h>
-#include <nuttx/compiler.h>
-#include <stdint.h>
-
-
-#include <stm32_gpio.h>
-
-/****************************************************************************************************
- * Definitions
- ****************************************************************************************************/
-
-#undef TRACE_PINS
-
-/* Configuration ************************************************************************************/
-
-#  define BOARD_HAS_USB_VALID           1
-#  define BOARD_HAS_NBAT_V              1
-#  define BOARD_HAS_NBAT_I              1
-
-/* PX4FMU GPIOs ***********************************************************************************/
-
-/* Trace Clock and D0-D3 are available on the trace connector
- *
- * TRACECLK PE2  - Dedicated       - Trace Connector Pin 1
- * TRACED0  PE3  - nLED_RED        - Trace Connector Pin 3
- * TRACED1  PE4  - nLED_GREEN      - Trace Connector Pin 5
- * TRACED2  PE5  - nLED_BLUE       - Trace Connector Pin 7
- * TRACED3  PE6  - nARMED          - Trace Connector Pin 8
-
- */
-
-/* LEDs are driven with push open drain to support Anode to 5V or 3.3V or used as TRACE0-2 */
-
-#if !defined(TRACE_PINS)
-#  define GPIO_nLED_RED        /* PE3 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
-#  define GPIO_nLED_GREEN      /* PE4 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
-#  define GPIO_nLED_BLUE       /* PE5 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN5)
-
-#  define BOARD_HAS_CONTROL_STATUS_LEDS      1
-#  define BOARD_OVERLOAD_LED     LED_RED
-#  define BOARD_ARMED_STATE_LED  LED_BLUE
-
-#else
-
-#  define GPIO_TRACECLK1 (GPIO_TRACECLK |GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN2)
-#  define GPIO_TRACED0   (GPIO_TRACED0_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN3)
-#  define GPIO_TRACED1   (GPIO_TRACED1_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN4)
-#  define GPIO_TRACED2   (GPIO_TRACED2_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN5)
-#  define GPIO_TRACED3   (GPIO_TRACED3_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN6)
-//#define GPIO_TRACESWO                        //(GPIO_ALT|GPIO_AF0|GPIO_PORTB|GPIO_PIN3)
-
-#  undef  BOARD_HAS_CONTROL_STATUS_LEDS
-#  undef  BOARD_OVERLOAD_LED
-#  undef  BOARD_ARMED_STATE_LED
-
-#  define GPIO_nLED_RED    GPIO_TRACED0
-#  define GPIO_nLED_GREEN  GPIO_TRACED1
-#  define GPIO_nLED_BLUE   GPIO_TRACED2
-#  define GPIO_nARMED      GPIO_TRACED3
-#  define GPIO_nARMED_INIT GPIO_TRACED3
-#endif
-
-/* SPI */
-
-#define SPI6_nRESET_EXTERNAL1       /* PF10 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTF|GPIO_PIN10)
-#define SPI6_RESET(on_true)          px4_arch_gpiowrite(SPI6_nRESET_EXTERNAL1, !(on_true))
-
-/* I2C busses */
-
-/* Devices on the onboard buses.
- *
- * Note that these are unshifted addresses.
- */
-#define PX4_I2C_OBDEV_SE050         0x48
-
-/*
- * ADC channels
- *
- * These are the channel numbers of the ADCs of the microcontroller that
- * can be used by the Px4 Firmware in the adc driver
- */
-
-/* ADC defines to be used in sensors.cpp to read from a particular channel */
-
-#define ADC1_CH(n)                  (n)
-
-/* N.B. there is no offset mapping needed for ADC3 because */
-#define ADC3_CH(n)                  (n)
-
-/* We are only use ADC3 for REV/VER.
- * ADC3_6V6 and ADC3_3V3 are mapped back to ADC1
- * To do this We are relying on PC2_C, PC3_C being connected to PC2, PC3
- * respectively by the SYSCFG_PMCR default of setting for PC3SO PC2SO PA1SO
- * PA0SO of 0.
- *
- *  0 Analog switch closed (pads are connected through the analog switch)
- *
- * So ADC3_INP0 is GPIO_ADC123_INP12
- *    ADC3_INP1 is GPIO_ADC12_INP13
- */
-
-/* Define GPIO pins used as ADC N.B. Channel numbers must match below  */
-
-#define PX4_ADC_GPIO  \
-	/* PA0  */  GPIO_ADC1_INP16,   \
-	/* PA4  */  GPIO_ADC12_INP18,  \
-	/* PB0  */  GPIO_ADC12_INP9,   \
-	/* PB1  */  GPIO_ADC12_INP5,   \
-	/* PC2  */  GPIO_ADC123_INP12, \
-	/* PC3  */  GPIO_ADC12_INP13,  \
-	/* PF12 */  GPIO_ADC1_INP6,    \
-	/* PH3  */  GPIO_ADC3_INP14,   \
-	/* PH4  */  GPIO_ADC3_INP15
-
-/* Define Channel numbers must match above GPIO pin IN(n)*/
-#define ADC_BATTERY_VOLTAGE_CHANNEL        	/* PB0 */  ADC1_CH(9)
-#define ADC_BATTERY_CURRENT_CHANNEL        	/* PC2 */  ADC3_CH(12)
-#define ADC_SCALED_12V_CHANNEL	     		/* PA4 */  ADC1_CH(18)
-#define ADC_SCALED_VDD_3V3_SENSORS_CHANNEL     /* PA0 */  ADC1_CH(16)
-#define ADC_SCALED_V5_CHANNEL                   /* PB1 */  ADC1_CH(5)
-#define ADC_HW_VER_SENSE_CHANNEL                /* PH3 */  ADC3_CH(14)
-#define ADC_HW_REV_SENSE_CHANNEL                /* PH4 */  ADC3_CH(15)
-
-#define ADC_CHANNELS \
-	((1 << ADC_BATTERY_VOLTAGE_CHANNEL)         | \
-	 (1 << ADC_BATTERY_CURRENT_CHANNEL)         | \
-	 (1 << ADC_SCALED_VDD_3V3_SENSORS_CHANNEL)  | \
-	 (1 << ADC_SCALED_V5_CHANNEL)               | \
-	 (1 << ADC_SCALED_12V_CHANNEL))
-
-
-#define BOARD_BATTERY1_V_DIV	 (21.0f) // (20k + 1k) / 1k = 21
-
-#define ADC_SCALED_PAYLOAD_SENSE ADC_SCALED_12V_CHANNEL
-
-/* HW has to large of R termination on ADC todo:change when HW value is chosen */
-
-#define HW_REV_VER_ADC_BASE STM32_ADC3_BASE
-
-#define SYSTEM_ADC_BASE STM32_ADC1_BASE
-
-/* HW has to large of R termination on ADC todo:change when HW value is chosen */
-#define BOARD_ADC_OPEN_CIRCUIT_V     (5.6f)
-
-/* HW Version and Revision drive signals Default to 1 to detect */
-#define BOARD_HAS_HW_SPLIT_VERSIONING
-
-#define GPIO_HW_VER_REV_DRIVE  /* PG0 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTG|GPIO_PIN0)
-#define GPIO_HW_REV_SENSE      /* PH4 */  GPIO_ADC3_INP15
-#define GPIO_HW_VER_SENSE      /* PH3 */  GPIO_ADC3_INP14
-#define HW_INFO_INIT_PREFIX    "ARKFPV"
-
-#define BOARD_NUM_SPI_CFG_HW_VERSIONS 2
-//                 Base/FMUM
-#define ARKFPV_0   HW_FMUM_ID(0x0) // ARKFPV,     Sensor Set  Rev 0
-#define ARKFPV_1   HW_FMUM_ID(0x1) // ARKFPV,     Sensor Set  Rev 1
-
-#define UAVCAN_NUM_IFACES_RUNTIME  1
-
-/* HEATER
- * PWM in future
- */
-#define GPIO_HEATER_OUTPUT   /* PB10  T2CH3 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10)
-#define HEATER_OUTPUT_EN(on_true)	       px4_arch_gpiowrite(GPIO_HEATER_OUTPUT, (on_true))
-
-/* PE6 is nARMED
- *  The GPIO will be set as input while not armed HW will have external HW Pull UP.
- *  While armed it shall be configured at a GPIO OUT set LOW
- */
-#if !defined(TRACE_PINS)
-#define GPIO_nARMED_INIT     /* PE6 */  (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN6)
-#define GPIO_nARMED          /* PE6 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN6)
-#define BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE(enabled)  px4_arch_configgpio((enabled) ? GPIO_nARMED : GPIO_nARMED_INIT)
-#define BOARD_GET_EXTERNAL_LOCKOUT_STATE() px4_arch_gpioread(GPIO_nARMED)
-#endif
-
-/* PWM
- */
-#define DIRECT_PWM_OUTPUT_CHANNELS   9
-
-#define GPIO_FMU_CH1                    /* PI0  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN0)
-#define GPIO_FMU_CH2                    /* PH12 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN12)
-#define GPIO_FMU_CH3                    /* PH11 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN11)
-#define GPIO_FMU_CH4                    /* PH10 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN10)
-#define GPIO_FMU_CH5                    /* PI5  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN5)
-#define GPIO_FMU_CH6                    /* PI6  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN6)
-#define GPIO_FMU_CH7                    /* PI7  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN7)
-#define GPIO_FMU_CH8                    /* PI2  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN2)
-#define GPIO_FMU_CH9                    /* PD12 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTD|GPIO_PIN12)
-
-#define GPIO_SPIX_SYNC                  /* PE9  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTE|GPIO_PIN9)
-
-/* Power supply control and monitoring GPIOs */
-
-#define GPIO_VDD_5V_PGOOD         	/* PF13 */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTF|GPIO_PIN13)
-#define GPIO_VDD_12V_PGOOD	 	/* PE15 */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTE|GPIO_PIN15)
-#define GPIO_5V_ON_BATTERY	 	/* PG1  */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTG|GPIO_PIN1)
-#define GPIO_VDD_12V_EN			/* PG4  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTG|GPIO_PIN4)
-
-#define GPIO_VDD_3V3_SD_CARD_EN         /* PC13 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13)
-
-
-#define BOARD_NUMBER_BRICKS             1
-
-/* Define True logic Power Control in arch agnostic form */
-
-#define VDD_3V3_SD_CARD_EN(on_true)        px4_arch_gpiowrite(GPIO_VDD_3V3_SD_CARD_EN, (on_true))
-#define PAYLOAD_POWER_EN(on_true)          px4_arch_gpiowrite(GPIO_VDD_12V_EN, (on_true))
-
-/* USB OTG FS
- *
- * PA9  OTG_FS_VBUS VBUS sensing
- */
-#define GPIO_OTGFS_VBUS         /* PA9 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTA|GPIO_PIN9)
-
-#define FLASH_BASED_PARAMS
-
-/* High-resolution timer */
-#define HRT_TIMER               3  /* use timer3 for the HRT */
-#define HRT_TIMER_CHANNEL       1 /* use capture/compare channel 1 */
-
-/* RC Serial port */
-
-#define RC_SERIAL_PORT                     "/dev/ttyS4"
-
-/* PWM input driver. Use FMU AUX5 pins attached to timer4 channel 2 */
-#define PWMIN_TIMER                       4
-#define PWMIN_TIMER_CHANNEL    /* T4C2 */ 2
-#define GPIO_PWM_IN            /* PD13 */ GPIO_TIM4_CH2IN_2
-
-#define SDIO_SLOTNO                    0  /* Only one slot */
-#define SDIO_MINOR                     0
-
-/* SD card bringup does not work if performed on the IDLE thread because it
- * will cause waiting.  Use either:
- *
- *  CONFIG_BOARDCTL=y, OR
- *  CONFIG_BOARD_INITIALIZE=y && CONFIG_BOARD_INITTHREAD=y
- */
-
-#if defined(CONFIG_BOARD_INITIALIZE) && !defined(CONFIG_BOARDCTL) && \
-   !defined(CONFIG_BOARD_INITTHREAD)
-#  warning SDIO initialization cannot be perfomed on the IDLE thread
-#endif
-
-/* By Providing BOARD_ADC_USB_CONNECTED (using the px4_arch abstraction)
- * this board support the ADC system_power interface, and therefore
- * provides the true logic GPIO BOARD_ADC_xxxx macros.
- */
-#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS))
-
-/* ARKFPV never powers off the Servo rail */
-
-#define BOARD_ADC_SERVO_VALID     (1)
-
-#define BOARD_ADC_BRICK_VALID   (px4_arch_gpioread(GPIO_VDD_5V_PGOOD))
-#define BOARD_GPIO_PAYOLOAD_V_VALID (px4_arch_gpioread(GPIO_VDD_12V_PGOOD))
-
-/* This board provides a DMA pool and APIs */
-#define BOARD_DMA_ALLOC_POOL_SIZE 5120
-
-/* This board provides the board_on_reset interface */
-
-#define BOARD_HAS_ON_RESET 1
-
-#if defined(TRACE_PINS)
-#define GPIO_TRACE                          \
-	GPIO_TRACECLK1,                           \
-	GPIO_TRACED0,                             \
-	GPIO_TRACED1,                             \
-	GPIO_TRACED2,                             \
-	GPIO_TRACED3
-#else
-#define GPIO_TRACE (GPIO_OUTPUT|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN2)
-#endif
-
-#define PX4_GPIO_INIT_LIST { \
-		GPIO_TRACE,                       \
-		PX4_ADC_GPIO,                     \
-		GPIO_HW_VER_REV_DRIVE,            \
-		GPIO_CAN1_TX,                     \
-		GPIO_CAN1_RX,                     \
-		GPIO_HEATER_OUTPUT,               \
-		GPIO_VDD_5V_PGOOD,                \
-		GPIO_VDD_12V_PGOOD,               \
-		GPIO_VDD_12V_EN,                  \
-		GPIO_5V_ON_BATTERY,               \
-		GPIO_VDD_3V3_SD_CARD_EN,          \
-		GPIO_nARMED_INIT,                 \
-		SPI6_nRESET_EXTERNAL1,            \
-		GPIO_FMU_CH1,     	          \
-		GPIO_FMU_CH2,     	          \
-		GPIO_FMU_CH3,     	          \
-		GPIO_FMU_CH4,     	          \
-		GPIO_FMU_CH5,     	          \
-		GPIO_FMU_CH6,     	          \
-		GPIO_FMU_CH7,     	          \
-		GPIO_FMU_CH8,     	          \
-		GPIO_FMU_CH9,     	          \
-		GPIO_SPIX_SYNC                    \
-	}
-
-#define BOARD_ENABLE_CONSOLE_BUFFER
-
-#define BOARD_NUM_IO_TIMERS  3
-#define BOARD_SPIX_SYNC_FREQ 32000
-
-__BEGIN_DECLS
-
-/****************************************************************************************************
- * Public Types
- ****************************************************************************************************/
-
-/****************************************************************************************************
- * Public data
- ****************************************************************************************************/
-
-#ifndef __ASSEMBLY__
-
-/****************************************************************************************************
- * Public Functions
- ****************************************************************************************************/
-
-/****************************************************************************
- * Name: stm32_sdio_initialize
- *
- * Description:
- *   Initialize SDIO-based MMC/SD card support
- *
- ****************************************************************************/
-
-int stm32_sdio_initialize(void);
-
-/****************************************************************************************************
- * Name: stm32_spiinitialize
- *
- * Description:
- *   Called to configure SPI chip select GPIO pins for the PX4FMU board.
- *
- ****************************************************************************************************/
-
-extern void stm32_spiinitialize(void);
-
-extern void stm32_usbinitialize(void);
-
-extern void board_peripheral_reset(int ms);
-
-#include <px4_platform_common/board_common.h>
-
-#endif /* __ASSEMBLY__ */
-
-__END_DECLS
@@ -1,85 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2022 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file bootloader_main.c
- *
- * FMU-specific early startup code for bootloader
-*/
-
-#include "board_config.h"
-#include "bl.h"
-
-#include <nuttx/config.h>
-#include <nuttx/board.h>
-#include <chip.h>
-#include <stm32_uart.h>
-#include <arch/board/board.h>
-#include "arm_internal.h"
-#include <px4_platform/gpio.h>
-#include <px4_platform_common/init.h>
-
-extern int sercon_main(int c, char **argv);
-
-__EXPORT void board_on_reset(int status) {}
-
-__EXPORT void stm32_boardinitialize(void)
-{
-	/* configure pins */
-	const uint32_t list[] = PX4_GPIO_INIT_LIST;
-
-	for (size_t gpio = 0; gpio < arraySize(list); gpio++) {
-		if (list[gpio] != 0) {
-			px4_arch_configgpio(list[gpio]);
-		}
-	}
-
-	/* configure USB interfaces */
-	stm32_usbinitialize();
-}
-
-__EXPORT int board_app_initialize(uintptr_t arg)
-{
-	return 0;
-}
-
-void board_late_initialize(void)
-{
-	sercon_main(0, NULL);
-}
-
-extern void sys_tick_handler(void);
-void board_timerhook(void)
-{
-	sys_tick_handler();
-}
@@ -1,140 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file can.c
- *
- * Board-specific CAN functions.
- */
-
-#if !defined(CONFIG_CAN)
-
-#include <stdint.h>
-
-#include "board_config.h"
-
-
-__EXPORT
-uint16_t board_get_can_interfaces(void)
-{
-	uint16_t enabled_interfaces = 0x3;
-
-	enabled_interfaces &= ~(1 << 1);
-
-	return enabled_interfaces;
-}
-
-#else
-
-#include <errno.h>
-#include <debug.h>
-
-#include <nuttx/can/can.h>
-#include <arch/board/board.h>
-
-#include "chip.h"
-#include "arm_internal.h"
-
-#include "chip.h"
-#include "stm32_can.h"
-#include "board_config.h"
-
-/************************************************************************************
- * Pre-processor Definitions
- ************************************************************************************/
-/* Configuration ********************************************************************/
-
-#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2)
-#  warning "Both CAN1 and CAN2 are enabled.  Assuming only CAN1."
-#  undef CONFIG_STM32_CAN2
-#endif
-
-#ifdef CONFIG_STM32_CAN1
-#  define CAN_PORT 1
-#else
-#  define CAN_PORT 2
-#endif
-
-/************************************************************************************
- * Private Functions
- ************************************************************************************/
-
-/************************************************************************************
- * Public Functions
- ************************************************************************************/
-int can_devinit(void);
-
-/************************************************************************************
- * Name: can_devinit
- *
- * Description:
- *   All STM32 architectures must provide the following interface to work with
- *   examples/can.
- *
- ************************************************************************************/
-
-int can_devinit(void)
-{
-	static bool initialized = false;
-	struct can_dev_s *can;
-	int ret;
-
-	/* Check if we have already initialized */
-
-	if (!initialized) {
-		/* Call stm32_caninitialize() to get an instance of the CAN interface */
-
-		can = stm32_caninitialize(CAN_PORT);
-
-		if (can == NULL) {
-			canerr("ERROR:  Failed to get CAN interface\n");
-			return -ENODEV;
-		}
-
-		/* Register the CAN driver at "/dev/can0" */
-
-		ret = can_register("/dev/can0", can);
-
-		if (ret < 0) {
-			canerr("ERROR: can_register failed: %d\n", ret);
-			return ret;
-		}
-
-		/* Now we are initialized */
-
-		initialized = true;
-	}
-
-	return OK;
-}
-#endif /* CONFIG_CAN */
@@ -1,129 +0,0 @@
-/*
- * hw_config.h
- *
- *  Created on: May 17, 2015
- *      Author: david_s5
- */
-
-#ifndef HW_CONFIG_H_
-#define HW_CONFIG_H_
-
-/****************************************************************************
- * 10-8--2016:
- *  To simplify the ripple effect on the tools, we will be using
- *  /dev/serial/by-id/<asterisk>PX4<asterisk> to locate PX4 devices. Therefore
- *  moving forward all Bootloaders must contain the prefix "PX4 BL "
- *  in the USBDEVICESTRING
- *  This Change will be made in an upcoming BL release
- ****************************************************************************/
-/*
- * Define usage to configure a bootloader
- *
- *
- * Constant                example          Usage
- * APP_LOAD_ADDRESS     0x08004000            - The address in Linker Script, where the app fw is org-ed
- * BOOTLOADER_DELAY     5000                  - Ms to wait while under USB pwr or bootloader request
- * BOARD_FMUV2
- * INTERFACE_USB        1                     - (Optional) Scan and use the USB interface for bootloading
- * INTERFACE_USART      1                     - (Optional) Scan and use the Serial interface for bootloading
- * USBDEVICESTRING      "PX4 BL FMU v2.x"     - USB id string
- * USBPRODUCTID         0x0011                - PID Should match defconfig
- * BOOT_DELAY_ADDRESS   0x000001a0            - (Optional) From the linker script from Linker Script to get a custom
- *                                               delay provided by an APP FW
- * BOARD_TYPE           9                     - Must match .prototype boad_id
- * _FLASH_KBYTES        (*(uint16_t *)0x1fff7a22) - Run time flash size detection
- * BOARD_FLASH_SECTORS  ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector
- * BOARD_FLASH_SECTORS   11                   - Hard coded zero based last sector
- * BOARD_FLASH_SIZE     (_FLASH_KBYTES*1024)-   Total Flash size of device, determined at run time.
- *                         (1024 * 1024)      - Hard coded Total Flash of device - The bootloader and app reserved will be deducted
- *                                              programmatically
- *
- * BOARD_FIRST_FLASH_SECTOR_TO_ERASE  2        - Optional sectors index in the flash_sectors table  (F4 only), to begin erasing.
- *                                               This is to allow sectors to be reserved for app fw usage. That will NOT be erased
- *                                               during a FW upgrade.
- *                                               The default is 0, and selects the first sector to be erased, as the 0th entry in the
- *                                               flash_sectors table. Which is the second physical sector of FLASH in the device.
- *                                               The first physical sector of FLASH is used by the bootloader, and is not defined
- *                                               in the table.
- *
- * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus
- *                                                                        BOOTLOADER_RESERVATION_SIZE  will be deducted from
- *                                                                        BOARD_FLASH_SIZE to determine the size of the App FW
- *                                                                        and hence the address space of FLASH to erase and program.
- * USBMFGSTRING            "PX4 AP"            - Optional USB MFG string (default is '3D Robotics' if not defined.)
- * SERIAL_BREAK_DETECT_DISABLED                -  Optional prevent break selection on Serial port from entering or staying in BL
- *
- * * Other defines are somewhat self explanatory.
- */
-
-/* Boot device selection list*/
-#define USB0_DEV       0x01
-#define SERIAL0_DEV    0x02
-#define SERIAL1_DEV    0x04
-
-#define APP_LOAD_ADDRESS               0x08020000
-#define BOOTLOADER_DELAY               5000
-#define INTERFACE_USB                  1
-#define INTERFACE_USB_CONFIG           "/dev/ttyACM0"
-#define BOARD_VBUS                     MK_GPIO_INPUT(GPIO_OTGFS_VBUS)
-
-//#define USE_VBUS_PULL_DOWN
-#define INTERFACE_USART                1
-#define INTERFACE_USART_CONFIG         "/dev/ttyS6,921600"
-#define BOOT_DELAY_ADDRESS             0x000001a0
-#define BOARD_TYPE                     59
-#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
-#define BOARD_FLASH_SECTORS            (14)
-#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)
-#define APP_RESERVATION_SIZE           (1 * 128 * 1024)
-
-#define OSC_FREQ                       16
-
-#define BOARD_PIN_LED_ACTIVITY         GPIO_nLED_BLUE // BLUE
-#define BOARD_PIN_LED_BOOTLOADER       GPIO_nLED_GREEN // GREEN
-#define BOARD_LED_ON                   0
-#define BOARD_LED_OFF                  1
-
-#define SERIAL_BREAK_DETECT_DISABLED   1
-
-/*
- * Uncommenting this allows to force the bootloader through
- * a PWM output pin. As this can accidentally initialize
- * an ESC prematurely, it is not recommended. This feature
- * has not been used and hence defaults now to off.
- *
- * # define BOARD_FORCE_BL_PIN_OUT         (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN14)
- * # define BOARD_FORCE_BL_PIN_IN          (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN11)
- *
- * # define BOARD_POWER_PIN_OUT           (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
- * # define BOARD_POWER_ON                 1
- * # define BOARD_POWER_OFF                0
- * # undef  BOARD_POWER_PIN_RELEASE        // Leave pin enabling Power - un comment to release (disable power)
- *
-*/
-
-#if !defined(ARCH_SN_MAX_LENGTH)
-# define ARCH_SN_MAX_LENGTH 12
-#endif
-
-#if !defined(APP_RESERVATION_SIZE)
-#  define APP_RESERVATION_SIZE 0
-#endif
-
-#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE)
-#  define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1
-#endif
-
-#if !defined(USB_DATA_ALIGN)
-# define USB_DATA_ALIGN
-#endif
-
-#ifndef BOOT_DEVICES_SELECTION
-#  define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
-#endif
-
-#ifndef BOOT_DEVICES_FILTER_ONUSB
-#  define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
-#endif
-
-#endif /* HW_CONFIG_H_ */
@@ -1,40 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2022 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include <px4_arch/i2c_hw_description.h>
-
-constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
-	initI2CBusExternal(1),
-	initI2CBusInternal(2),
-	initI2CBusInternal(4),
-};
@@ -1,299 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2012-2022 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file init.c
- *
- * ARKFMU-specific early startup code.  This file implements the
- * board_app_initialize() function that is called early by nsh during startup.
- *
- * Code here is run before the rcS script is invoked; it should start required
- * subsystems and perform board-specific initialization.
- */
-
-/****************************************************************************
- * Included Files
- ****************************************************************************/
-
-#include "board_config.h"
-#include "spix_sync.h"
-
-#include <stdbool.h>
-#include <stdio.h>
-#include <string.h>
-#include <debug.h>
-#include <errno.h>
-
-#include <nuttx/config.h>
-#include <nuttx/board.h>
-#include <nuttx/spi/spi.h>
-#include <nuttx/sdio.h>
-#include <nuttx/mmcsd.h>
-#include <nuttx/analog/adc.h>
-#include <nuttx/mm/gran.h>
-#include <chip.h>
-#include <stm32_uart.h>
-#include <arch/board/board.h>
-#include "arm_internal.h"
-
-#include <drivers/drv_hrt.h>
-#include <drivers/drv_board_led.h>
-#include <systemlib/px4_macros.h>
-#include <px4_arch/io_timer.h>
-#include <px4_platform_common/init.h>
-#include <px4_platform_common/px4_manifest.h>
-#include <px4_platform/gpio.h>
-#include <px4_platform/board_determine_hw_info.h>
-#include <px4_platform/board_dma_alloc.h>
-
-# if defined(FLASH_BASED_PARAMS)
-#  include <parameters/flashparams/flashfs.h>
-#endif
-
-/****************************************************************************
- * Pre-Processor Definitions
- ****************************************************************************/
-
-/* Configuration ************************************************************/
-
-/*
- * Ideally we'd be able to get these from arm_internal.h,
- * but since we want to be able to disable the NuttX use
- * of leds for system indication at will and there is no
- * separate switch, we need to build independent of the
- * CONFIG_ARCH_LEDS configuration switch.
- */
-__BEGIN_DECLS
-extern void led_init(void);
-extern void led_on(int led);
-extern void led_off(int led);
-__END_DECLS
-
-
-/************************************************************************************
- * Name: board_peripheral_reset
- *
- * Description:
- *
- ************************************************************************************/
-__EXPORT void board_peripheral_reset(int ms)
-{
-	/* set the peripheral rails off */
-
-	PAYLOAD_POWER_EN(false);
-	board_control_spi_sensors_power(false, 0xffff);
-	SPI6_RESET(true);
-
-	/* wait for the peripheral rail to reach GND */
-	usleep(ms * 1000);
-	syslog(LOG_DEBUG, "reset done, %d ms\n", ms);
-
-	/* re-enable power */
-
-	/* switch the peripheral rail back on */
-	board_control_spi_sensors_power(true, 0xffff);
-	PAYLOAD_POWER_EN(true);
-
-	/* Release SPI6 Reset */
-	SPI6_RESET(false);
-}
-
-/************************************************************************************
- * Name: board_on_reset
- *
- * Description:
- * Optionally provided function called on entry to board_system_reset
- * It should perform any house keeping prior to the rest.
- *
- * status - 1 if resetting to boot loader
- *          0 if just resetting
- *
- ************************************************************************************/
-__EXPORT void board_on_reset(int status)
-{
-	for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) {
-		px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i)));
-	}
-
-	if (status >= 0) {
-		up_mdelay(6);
-	}
-}
-
-/************************************************************************************
- * Name: stm32_boardinitialize
- *
- * Description:
- *   All STM32 architectures must provide the following entry point.  This entry point
- *   is called early in the initialization -- after all memory has been configured
- *   and mapped but before any devices have been initialized.
- *
- ************************************************************************************/
-
-__EXPORT void
-stm32_boardinitialize(void)
-{
-	board_on_reset(-1); /* Reset PWM first thing */
-
-	/* configure LEDs */
-
-	board_autoled_initialize();
-
-	/* configure pins */
-
-	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
-	px4_gpio_init(gpio, arraySize(gpio));
-
-	/* configure USB interfaces */
-
-	stm32_usbinitialize();
-
-}
-
-/****************************************************************************
- * Name: board_app_initialize
- *
- * Description:
- *   Perform application specific initialization.  This function is never
- *   called directly from application code, but only indirectly via the
- *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
- *
- * Input Parameters:
- *   arg - The boardctl() argument is passed to the board_app_initialize()
- *         implementation without modification.  The argument has no
- *         meaning to NuttX; the meaning of the argument is a contract
- *         between the board-specific initalization logic and the the
- *         matching application logic.  The value cold be such things as a
- *         mode enumeration value, a set of DIP switch switch settings, a
- *         pointer to configuration data read from a file or serial FLASH,
- *         or whatever you would like to do with it.  Every implementation
- *         should accept zero/NULL as a default configuration.
- *
- * Returned Value:
- *   Zero (OK) is returned on success; a negated errno value is returned on
- *   any failure to indicate the nature of the failure.
- *
- ****************************************************************************/
-
-__EXPORT int board_app_initialize(uintptr_t arg)
-{
-	/* Power on Interfaces */
-	PAYLOAD_POWER_EN(true);
-
-	SPI6_RESET(false);
-
-	/* Need hrt running before using the ADC */
-
-	px4_platform_init();
-
-	// Use the default HW_VER_REV(0x0,0x0) for Ramtron
-
-	stm32_spiinitialize();
-
-#if defined(FLASH_BASED_PARAMS)
-	static sector_descriptor_t params_sector_map[] = {
-		{15, 128 * 1024, 0x081E0000},
-		{0, 0, 0},
-	};
-
-	/* Initialize the flashfs layer to use heap allocated memory */
-	int result = parameter_flashfs_init(params_sector_map, NULL, 0);
-
-	if (result != OK) {
-		syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
-		led_on(LED_AMBER);
-	}
-
-#endif // FLASH_BASED_PARAMS
-
-	/* Configure the HW based on the manifest */
-
-	px4_platform_configure();
-
-	if (OK == board_determine_hw_info()) {
-		syslog(LOG_INFO, "[boot] Rev 0x%1x : Ver 0x%1x %s\n", board_get_hw_revision(), board_get_hw_version(),
-		       board_get_hw_type_name());
-
-	} else {
-		syslog(LOG_ERR, "[boot] Failed to read HW revision and version\n");
-	}
-
-	/* Configure the Actual SPI interfaces (after we determined the HW version)  */
-
-	stm32_spiinitialize();
-
-	board_spi_reset(10, 0xffff);
-
-	/* Configure the DMA allocator */
-
-	if (board_dma_alloc_init() < 0) {
-		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
-	}
-
-#if defined(SERIAL_HAVE_RXDMA)
-	// set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event.
-	static struct hrt_call serial_dma_call;
-	hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
-#endif
-
-	/* initial LED state */
-	drv_led_start();
-	led_off(LED_RED);
-	led_on(LED_GREEN); // Indicate Power.
-	led_off(LED_BLUE);
-
-	if (board_hardfault_init(2, true) != 0) {
-		led_on(LED_RED);
-	}
-
-	// Ensure Power is off for > 10 mS
-	usleep(15 * 1000);
-	VDD_3V3_SD_CARD_EN(true);
-	usleep(500 * 1000);
-
-#ifdef CONFIG_MMCSD
-	int ret = stm32_sdio_initialize();
-
-	if (ret != OK) {
-		led_on(LED_RED);
-		return ret;
-	}
-
-#endif /* CONFIG_MMCSD */
-
-	/* Configure the SPIX_SYNC output */
-	spix_sync_servo_init(BOARD_SPIX_SYNC_FREQ);
-	spix_sync_servo_set(0, 150);
-
-	return OK;
-}
@@ -1,234 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (c) 2013 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file led.c
- *
- * ARKFMU LED backend.
- */
-
-#include <px4_platform_common/px4_config.h>
-
-#include <stdbool.h>
-
-#include "chip.h"
-#include "stm32_gpio.h"
-#include "board_config.h"
-
-#include <nuttx/board.h>
-#include <arch/board/board.h>
-
-/*
- * Ideally we'd be able to get these from arm_internal.h,
- * but since we want to be able to disable the NuttX use
- * of leds for system indication at will and there is no
- * separate switch, we need to build independent of the
- * CONFIG_ARCH_LEDS configuration switch.
- */
-__BEGIN_DECLS
-extern void led_init(void);
-extern void led_on(int led);
-extern void led_off(int led);
-extern void led_toggle(int led);
-__END_DECLS
-
-#ifdef CONFIG_ARCH_LEDS
-static bool nuttx_owns_leds = true;
-//                                B  R  S  G
-//                                0  1  2  3
-static const uint8_t xlatpx4[] = {1, 2, 4, 0};
-#  define xlat(p) xlatpx4[(p)]
-static uint32_t g_ledmap[] = {
-	GPIO_nLED_GREEN,   // Indexed by BOARD_LED_GREEN
-	GPIO_nLED_BLUE,    // Indexed by BOARD_LED_BLUE
-	GPIO_nLED_RED,     // Indexed by BOARD_LED_RED
-};
-
-#else
-
-#  define xlat(p) (p)
-static uint32_t g_ledmap[] = {
-	GPIO_nLED_BLUE,                     // Indexed by LED_BLUE
-	GPIO_nLED_RED,                      // Indexed by LED_RED, LED_AMBER
-	0,                                  // Indexed by LED_SAFETY (defaulted to an input)
-	GPIO_nLED_GREEN,                    // Indexed by LED_GREEN
-};
-
-#endif
-
-__EXPORT void led_init(void)
-{
-	for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
-		if (g_ledmap[l] != 0) {
-			stm32_configgpio(g_ledmap[l]);
-		}
-	}
-}
-
-static void phy_set_led(int led, bool state)
-{
-	/* Drive Low to switch on */
-
-	if (g_ledmap[led] != 0) {
-		stm32_gpiowrite(g_ledmap[led], !state);
-	}
-}
-
-static bool phy_get_led(int led)
-{
-	/* If Low it is on */
-	if (g_ledmap[led] != 0) {
-		return !stm32_gpioread(g_ledmap[led]);
-	}
-
-	return false;
-}
-
-__EXPORT void led_on(int led)
-{
-	phy_set_led(xlat(led), true);
-}
-
-__EXPORT void led_off(int led)
-{
-	phy_set_led(xlat(led), false);
-}
-
-__EXPORT void led_toggle(int led)
-{
-	phy_set_led(xlat(led), !phy_get_led(xlat(led)));
-}
-
-#ifdef CONFIG_ARCH_LEDS
-/****************************************************************************
- * Public Functions
- ****************************************************************************/
-
-/****************************************************************************
- * Name: board_autoled_initialize
- ****************************************************************************/
-
-void board_autoled_initialize(void)
-{
-	led_init();
-}
-
-/****************************************************************************
- * Name: board_autoled_on
- ****************************************************************************/
-
-void board_autoled_on(int led)
-{
-	if (!nuttx_owns_leds) {
-		return;
-	}
-
-	switch (led) {
-	default:
-		break;
-
-	case LED_HEAPALLOCATE:
-		phy_set_led(BOARD_LED_BLUE, true);
-		break;
-
-	case LED_IRQSENABLED:
-		phy_set_led(BOARD_LED_BLUE, false);
-		phy_set_led(BOARD_LED_GREEN, true);
-		break;
-
-	case LED_STACKCREATED:
-		phy_set_led(BOARD_LED_GREEN, true);
-		phy_set_led(BOARD_LED_BLUE, true);
-		break;
-
-	case LED_INIRQ:
-		phy_set_led(BOARD_LED_BLUE, true);
-		break;
-
-	case LED_SIGNAL:
-		phy_set_led(BOARD_LED_GREEN, true);
-		break;
-
-	case LED_ASSERTION:
-		phy_set_led(BOARD_LED_RED, true);
-		phy_set_led(BOARD_LED_BLUE, true);
-		break;
-
-	case LED_PANIC:
-		phy_set_led(BOARD_LED_RED, true);
-		break;
-
-	case LED_IDLE : /* IDLE */
-		phy_set_led(BOARD_LED_RED, true);
-		break;
-	}
-}
-
-/****************************************************************************
- * Name: board_autoled_off
- ****************************************************************************/
-
-void board_autoled_off(int led)
-{
-	if (!nuttx_owns_leds) {
-		return;
-	}
-
-	switch (led) {
-	default:
-		break;
-
-	case LED_SIGNAL:
-		phy_set_led(BOARD_LED_GREEN, false);
-		break;
-
-	case LED_INIRQ:
-		phy_set_led(BOARD_LED_BLUE, false);
-		break;
-
-	case LED_ASSERTION:
-		phy_set_led(BOARD_LED_RED, false);
-		phy_set_led(BOARD_LED_BLUE, false);
-		break;
-
-	case LED_PANIC:
-		phy_set_led(BOARD_LED_RED, false);
-		break;
-
-	case LED_IDLE : /* IDLE */
-		phy_set_led(BOARD_LED_RED, false);
-		break;
-	}
-}
-
-#endif /* CONFIG_ARCH_LEDS */
@@ -1,55 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2024 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include <nuttx/config.h>
-#include <board_config.h>
-
-#include <nuttx/spi/spi.h>
-#include <px4_platform_common/px4_manifest.h>
-
-static const px4_mft_entry_s mft_mft = {
-	.type = MFT,
-	.pmft = (void *) system_query_manifest,
-};
-
-static const px4_mft_s mft = {
-	.nmft = 1,
-	.mfts = {
-		&mft_mft,
-	}
-};
-
-const px4_mft_s *board_get_manifest(void)
-{
-	return &mft;
-}
@@ -1,177 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
- *   Author: Gregory Nutt <gnutt@nuttx.org>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name NuttX nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/****************************************************************************
- * Included Files
- ****************************************************************************/
-
-#include <nuttx/config.h>
-#include <board_config.h>
-
-#include <stdbool.h>
-#include <stdio.h>
-#include <debug.h>
-#include <errno.h>
-
-#include <nuttx/sdio.h>
-#include <nuttx/mmcsd.h>
-
-#include "chip.h"
-#include "board_config.h"
-#include "stm32_gpio.h"
-#include "stm32_sdmmc.h"
-
-#ifdef CONFIG_MMCSD
-
-
-/****************************************************************************
- * Pre-processor Definitions
- ****************************************************************************/
-
-/* Card detections requires card support and a card detection GPIO */
-
-#define HAVE_NCD   1
-#if !defined(GPIO_SDMMC1_NCD)
-#  undef HAVE_NCD
-#endif
-
-/****************************************************************************
- * Private Data
- ****************************************************************************/
-
-static FAR struct sdio_dev_s *sdio_dev;
-#ifdef HAVE_NCD
-static bool g_sd_inserted = 0xff; /* Impossible value */
-#endif
-
-/****************************************************************************
- * Private Functions
- ****************************************************************************/
-
-/****************************************************************************
- * Name: stm32_ncd_interrupt
- *
- * Description:
- *   Card detect interrupt handler.
- *
- ****************************************************************************/
-
-#ifdef HAVE_NCD
-static int stm32_ncd_interrupt(int irq, FAR void *context)
-{
-	bool present;
-
-	present = !stm32_gpioread(GPIO_SDMMC1_NCD);
-
-	if (sdio_dev && present != g_sd_inserted) {
-		sdio_mediachange(sdio_dev, present);
-		g_sd_inserted = present;
-	}
-
-	return OK;
-}
-#endif
-
-/****************************************************************************
- * Public Functions
- ****************************************************************************/
-
-/****************************************************************************
- * Name: stm32_sdio_initialize
- *
- * Description:
- *   Initialize SDIO-based MMC/SD card support
- *
- ****************************************************************************/
-
-int stm32_sdio_initialize(void)
-{
-	int ret;
-
-#ifdef HAVE_NCD
-	/* Card detect */
-
-	bool cd_status;
-
-	/* Configure the card detect GPIO */
-
-	stm32_configgpio(GPIO_SDMMC1_NCD);
-
-	/* Register an interrupt handler for the card detect pin */
-
-	stm32_gpiosetevent(GPIO_SDMMC1_NCD, true, true, true, stm32_ncd_interrupt);
-#endif
-
-	/* Mount the SDIO-based MMC/SD block driver */
-	/* First, get an instance of the SDIO interface */
-
-	finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO);
-
-	sdio_dev = sdio_initialize(SDIO_SLOTNO);
-
-	if (!sdio_dev) {
-		syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", SDIO_SLOTNO);
-		return -ENODEV;
-	}
-
-	/* Now bind the SDIO interface to the MMC/SD driver */
-
-	finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR);
-
-	ret = mmcsd_slotinitialize(SDIO_MINOR, sdio_dev);
-
-	if (ret != OK) {
-		syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
-		return ret;
-	}
-
-	finfo("Successfully bound SDIO to the MMC/SD driver\n");
-
-#ifdef HAVE_NCD
-	/* Use SD card detect pin to check if a card is g_sd_inserted */
-
-	cd_status = !stm32_gpioread(GPIO_SDMMC1_NCD);
-	finfo("Card detect : %d\n", cd_status);
-
-	sdio_mediachange(sdio_dev, cd_status);
-#else
-	/* Assume that the SD card is inserted.  What choice do we have? */
-
-	sdio_mediachange(sdio_dev, true);
-#endif
-
-	return OK;
-}
-
-#endif /* CONFIG_MMCSD */
@@ -1,57 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2024 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include <px4_arch/spi_hw_description.h>
-#include <drivers/drv_sensor.h>
-#include <nuttx/spi/spi.h>
-
-constexpr px4_spi_bus_all_hw_t px4_spi_buses_all_hw[BOARD_NUM_SPI_CFG_HW_VERSIONS] = {
-	initSPIFmumID(ARKFPV_0, {
-		initSPIBus(SPI::Bus::SPI1, {
-			initSPIDevice(DRV_IMU_DEVTYPE_IIM42653, SPI::CS{GPIO::PortI, GPIO::Pin9}, SPI::DRDY{GPIO::PortF, GPIO::Pin2}),
-		}, {GPIO::PortI, GPIO::Pin11}),
-		initSPIBusExternal(SPI::Bus::SPI6, {
-			initSPIConfigExternal(SPI::CS{GPIO::PortI, GPIO::Pin10}, SPI::DRDY{GPIO::PortD, GPIO::Pin11})
-		}),
-	}),
-	initSPIFmumID(ARKFPV_1, { // Placeholder
-		initSPIBus(SPI::Bus::SPI1, {
-			initSPIDevice(DRV_IMU_DEVTYPE_IIM42653, SPI::CS{GPIO::PortI, GPIO::Pin9}, SPI::DRDY{GPIO::PortF, GPIO::Pin2}),
-		}, {GPIO::PortI, GPIO::Pin11}),
-		initSPIBusExternal(SPI::Bus::SPI6, {
-			initSPIConfigExternal(SPI::CS{GPIO::PortI, GPIO::Pin10}, SPI::DRDY{GPIO::PortD, GPIO::Pin11})
-		}),
-	}),
-};
-
-static constexpr bool unused = validateSPIConfig(px4_spi_buses_all_hw);
@@ -1,309 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2023 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name Airmind nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
-* @file spix_sync.c
-*
-*
-*/
-
-#include <px4_platform_common/px4_config.h>
-
-#include <board_config.h>
-
-#include <sys/types.h>
-#include <stdint.h>
-#include <string.h>
-#include <stdlib.h>
-#include <stdbool.h>
-#include <fcntl.h>
-#include <unistd.h>
-#include <stdio.h>
-#include <ctype.h>
-
-
-#include <perf/perf_counter.h>
-#include <systemlib/err.h>
-#include <systemlib/px4_macros.h>
-
-#include <px4_arch/io_timer.h>
-
-#include "spix_sync.h"
-
-#define REG(_tmr, _reg) (*(volatile uint32_t *)(spix_sync_timers[_tmr].base + _reg))
-
-#define rCR1(_tmr)      REG(_tmr, STM32_GTIM_CR1_OFFSET)
-#define rCR2(_tmr)      REG(_tmr, STM32_GTIM_CR2_OFFSET)
-#define rSMCR(_tmr)     REG(_tmr, STM32_GTIM_SMCR_OFFSET)
-#define rDIER(_tmr)     REG(_tmr, STM32_GTIM_DIER_OFFSET)
-#define rSR(_tmr)       REG(_tmr, STM32_GTIM_SR_OFFSET)
-#define rEGR(_tmr)      REG(_tmr, STM32_GTIM_EGR_OFFSET)
-#define rCCMR1(_tmr)    REG(_tmr, STM32_GTIM_CCMR1_OFFSET)
-#define rCCMR2(_tmr)    REG(_tmr, STM32_GTIM_CCMR2_OFFSET)
-#define rCCER(_tmr)     REG(_tmr, STM32_GTIM_CCER_OFFSET)
-#define rCNT(_tmr)      REG(_tmr, STM32_GTIM_CNT_OFFSET)
-#define rPSC(_tmr)      REG(_tmr, STM32_GTIM_PSC_OFFSET)
-#define rARR(_tmr)      REG(_tmr, STM32_GTIM_ARR_OFFSET)
-#define rCCR1(_tmr)     REG(_tmr, STM32_GTIM_CCR1_OFFSET)
-#define rCCR2(_tmr)     REG(_tmr, STM32_GTIM_CCR2_OFFSET)
-#define rCCR3(_tmr)     REG(_tmr, STM32_GTIM_CCR3_OFFSET)
-#define rCCR4(_tmr)     REG(_tmr, STM32_GTIM_CCR4_OFFSET)
-#define rDCR(_tmr)      REG(_tmr, STM32_GTIM_DCR_OFFSET)
-#define rDMAR(_tmr)     REG(_tmr, STM32_GTIM_DMAR_OFFSET)
-#define rBDTR(_tmr)     REG(_tmr, STM32_ATIM_BDTR_OFFSET)
-
-#define BOARD_SPIX_SYNC_PWM_FREQ 1024000
-
-unsigned
-spix_sync_timer_get_period(unsigned timer)
-{
-	return (rARR(timer));
-}
-
-static void spix_sync_timer_init_timer(unsigned timer, unsigned rate)
-{
-	if (spix_sync_timers[timer].base) {
-
-		irqstate_t flags = px4_enter_critical_section();
-
-		/* enable the timer clock before we try to talk to it */
-
-		modifyreg32(spix_sync_timers[timer].clock_register, 0, spix_sync_timers[timer].clock_bit);
-
-		/* disable and configure the timer */
-		rCR1(timer) = 0;
-		rCR2(timer) = 0;
-		rSMCR(timer) = 0;
-		rDIER(timer) = 0;
-		rCCER(timer) = 0;
-		rCCMR1(timer) = 0;
-		rCCMR2(timer) = 0;
-		rCCR1(timer) = 0;
-		rCCR2(timer) = 0;
-		rCCR3(timer) = 0;
-		rCCR4(timer) = 0;
-		rCCER(timer) = 0;
-		rDCR(timer) = 0;
-
-		if ((spix_sync_timers[timer].base == STM32_TIM1_BASE) || (spix_sync_timers[timer].base == STM32_TIM8_BASE)) {
-
-			/* master output enable = on */
-
-			rBDTR(timer) = ATIM_BDTR_MOE;
-		}
-
-		/* If the timer clock source provided as clock_freq is the STM32_APBx_TIMx_CLKIN
-		 * then configure the timer to free-run at 1MHz.
-		 * Otherwise, other frequencies are attainable by adjusting .clock_freq accordingly.
-		 */
-
-		rPSC(timer) = (spix_sync_timers[timer].clock_freq / BOARD_SPIX_SYNC_PWM_FREQ) - 1;
-
-		/* configure the timer to update at the desired rate */
-
-		rARR(timer) = (BOARD_SPIX_SYNC_PWM_FREQ / rate) - 1;
-
-		/* generate an update event; reloads the counter and all registers */
-		rEGR(timer) = GTIM_EGR_UG;
-
-		px4_leave_critical_section(flags);
-	}
-
-}
-
-void spix_sync_channel_init(unsigned channel)
-{
-	/* Only initialize used channels */
-
-	if (spix_sync_channels[channel].timer_channel) {
-
-		unsigned timer = spix_sync_channels[channel].timer_index;
-
-		/* configure the GPIO first */
-		px4_arch_configgpio(spix_sync_channels[channel].gpio_out);
-
-		uint16_t polarity = spix_sync_channels[channel].masks;
-
-		/* configure the channel */
-		switch (spix_sync_channels[channel].timer_channel) {
-		case 1:
-			rCCMR1(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR1_OC1M_SHIFT) | GTIM_CCMR1_OC1PE;
-			rCCER(timer) |= polarity | GTIM_CCER_CC1E;
-			break;
-
-		case 2:
-			rCCMR1(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR1_OC2M_SHIFT) | GTIM_CCMR1_OC2PE;
-			rCCER(timer) |= polarity | GTIM_CCER_CC2E;
-			break;
-
-		case 3:
-			rCCMR2(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR2_OC3M_SHIFT) | GTIM_CCMR2_OC3PE;
-			rCCER(timer) |= polarity | GTIM_CCER_CC3E;
-			break;
-
-		case 4:
-			rCCMR2(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR2_OC4M_SHIFT) | GTIM_CCMR2_OC4PE;
-			rCCER(timer) |= polarity | GTIM_CCER_CC4E;
-			break;
-		}
-	}
-}
-
-int
-spix_sync_servo_set(unsigned channel, uint8_t  cvalue)
-{
-	if (channel >= arraySize(spix_sync_channels)) {
-		return -1;
-	}
-
-	unsigned timer = spix_sync_channels[channel].timer_index;
-
-	/* test timer for validity */
-	if ((spix_sync_timers[timer].base == 0) ||
-	    (spix_sync_channels[channel].gpio_out == 0)) {
-		return -1;
-	}
-
-	unsigned period = spix_sync_timer_get_period(timer);
-
-	unsigned value = (unsigned)cvalue * period / 255;
-
-	/* configure the channel */
-	if (value > 0) {
-		value--;
-	}
-
-
-	switch (spix_sync_channels[channel].timer_channel) {
-	case 1:
-		rCCR1(timer) = value;
-		break;
-
-	case 2:
-		rCCR2(timer) = value;
-		break;
-
-	case 3:
-		rCCR3(timer) = value;
-		break;
-
-	case 4:
-		rCCR4(timer) = value;
-		break;
-
-	default:
-		return -1;
-	}
-
-	return 0;
-}
-
-unsigned spix_sync_servo_get(unsigned channel)
-{
-	if (channel >= 3) {
-		return 0;
-	}
-
-	unsigned timer = spix_sync_channels[channel].timer_index;
-	uint16_t value = 0;
-
-	/* test timer for validity */
-	if ((spix_sync_timers[timer].base == 0) ||
-	    (spix_sync_channels[channel].timer_channel == 0)) {
-		return 0;
-	}
-
-	/* configure the channel */
-	switch (spix_sync_channels[channel].timer_channel) {
-	case 1:
-		value = rCCR1(timer);
-		break;
-
-	case 2:
-		value = rCCR2(timer);
-		break;
-
-	case 3:
-		value = rCCR3(timer);
-		break;
-
-	case 4:
-		value = rCCR4(timer);
-		break;
-	}
-
-	unsigned period = spix_sync_timer_get_period(timer);
-	return ((value + 1) * 255 / period);
-}
-
-int spix_sync_servo_init(unsigned rate)
-{
-	/* do basic timer initialisation first */
-	for (unsigned i = 0; i < arraySize(spix_sync_timers); i++) {
-		spix_sync_timer_init_timer(i, rate);
-	}
-
-	/* now init channels */
-	for (unsigned i = 0; i < arraySize(spix_sync_channels); i++) {
-		spix_sync_channel_init(i);
-	}
-
-	spix_sync_servo_arm(true);
-	return OK;
-}
-
-void
-spix_sync_servo_deinit(void)
-{
-	/* disable the timers */
-	spix_sync_servo_arm(false);
-}
-void
-spix_sync_servo_arm(bool armed)
-{
-	/* iterate timers and arm/disarm appropriately */
-	for (unsigned i = 0; i < arraySize(spix_sync_timers); i++) {
-		if (spix_sync_timers[i].base != 0) {
-			if (armed) {
-				/* force an update to preload all registers */
-				rEGR(i) = GTIM_EGR_UG;
-
-				/* arm requires the timer be enabled */
-				rCR1(i) |= GTIM_CR1_CEN | GTIM_CR1_ARPE;
-
-			} else {
-				rCR1(i) = 0;
-			}
-		}
-	}
-}
@@ -1,42 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2023 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-__BEGIN_DECLS
-void spix_sync_channel_init(unsigned channel);
-int spix_sync_servo_set(unsigned channel, uint8_t  value);
-unsigned spix_sync_servo_get(unsigned channel);
-int spix_sync_servo_init(unsigned rate);
-void spix_sync_servo_deinit(void);
-void spix_sync_servo_arm(bool armed);
-unsigned spix_sync_timer_get_period(unsigned timer);
-__END_DECLS
@@ -1,86 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-#include <px4_arch/io_timer_hw_description.h>
-
-/* Timer allocation
- *
- * TIM5_CH4  T FMU_CH1
- * TIM5_CH3  T FMU_CH2
- * TIM5_CH2  T FMU_CH3
- * TIM5_CH1  T FMU_CH4
- *
- * TIM8_CH1  T FMU_CH5
- * TIM8_CH2  T FMU_CH6
- * TIM8_CH3  T FMU_CH7
- * TIM8_CH4  T FMU_CH8
- *
- * TIM4_CH1  T FMU_CH9
- *
- * TIM1_CH1  T SPIX_SYNC              > Pulse or GPIO strobe
- *
- * TIM2_CH3  T HEATER                 > PWM OUT or GPIO
- *
- * TIM3_CH1  T HRT_TIMER
- *
- */
-
-constexpr io_timers_t io_timers[MAX_IO_TIMERS] = {
-	initIOTimer(Timer::Timer5, DMA{DMA::Index1}),
-	initIOTimer(Timer::Timer8, DMA{DMA::Index1}),
-	initIOTimer(Timer::Timer4, DMA{DMA::Index1}),
-};
-
-constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
-	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel4}, {GPIO::PortI, GPIO::Pin0}),
-	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel3}, {GPIO::PortH, GPIO::Pin12}),
-	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel2}, {GPIO::PortH, GPIO::Pin11}),
-	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel1}, {GPIO::PortH, GPIO::Pin10}),
-	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel1}, {GPIO::PortI, GPIO::Pin5}),
-	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel2}, {GPIO::PortI, GPIO::Pin6}),
-	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel3}, {GPIO::PortI, GPIO::Pin7}),
-	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel4}, {GPIO::PortI, GPIO::Pin2}),
-	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel1}, {GPIO::PortD, GPIO::Pin12}),
-};
-
-constexpr io_timers_channel_mapping_t io_timers_channel_mapping =
-	initIOTimerChannelMapping(io_timers, timer_io_channels);
-
-
-constexpr io_timers_t spix_sync_timers[MAX_SPIX_SYNC_TIMERS] = {
-	initIOTimer(Timer::Timer1),
-};
-
-constexpr timer_io_channels_t spix_sync_channels[MAX_SPIX_SYNC_TIMERS] = {
-	initIOTimerChannel(spix_sync_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}),
-};
@@ -1,105 +0,0 @@
-/****************************************************************************
- *
- *   Copyright (C) 2016 PX4 Development Team. All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in
- *    the documentation and/or other materials provided with the
- *    distribution.
- * 3. Neither the name PX4 nor the names of its contributors may be
- *    used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
- * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
- * POSSIBILITY OF SUCH DAMAGE.
- *
- ****************************************************************************/
-
-/**
- * @file usb.c
- *
- * Board-specific USB functions.
- */
-
-/************************************************************************************
- * Included Files
- ************************************************************************************/
-
-#include <px4_platform_common/px4_config.h>
-
-#include <sys/types.h>
-#include <stdint.h>
-#include <stdbool.h>
-#include <debug.h>
-
-#include <nuttx/usb/usbdev.h>
-#include <nuttx/usb/usbdev_trace.h>
-
-#include "arm_internal.h"
-#include <chip.h>
-#include <stm32_gpio.h>
-#include <stm32_otg.h>
-#include "board_config.h"
-
-/************************************************************************************
- * Definitions
- ************************************************************************************/
-
-/************************************************************************************
- * Private Functions
- ************************************************************************************/
-
-/************************************************************************************
- * Public Functions
- ************************************************************************************/
-
-/************************************************************************************
- * Name: stm32_usbinitialize
- *
- * Description:
- *   Called to setup USB-related GPIO pins for the ARKFMU board.
- *
- ************************************************************************************/
-
-__EXPORT void stm32_usbinitialize(void)
-{
-	/* The OTG FS has an internal soft pull-up */
-
-	/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
-
-#ifdef CONFIG_STM32H7_OTGFS
-	stm32_configgpio(GPIO_OTGFS_VBUS);
-#endif
-}
-
-/************************************************************************************
- * Name:  stm32_usbsuspend
- *
- * Description:
- *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
- *   used.  This function is called whenever the USB enters or leaves suspend mode.
- *   This is an opportunity for the board logic to shutdown clocks, power, etc.
- *   while the USB is suspended.
- *
- ************************************************************************************/
-
-__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
-{
-	uinfo("resume: %d\n", resume);
-}
@@ -8,9 +8,7 @@ CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_BROADCOM_AFBRS50=y
-CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_HEATER=y
@@ -32,10 +32,19 @@ then
 	param set-default SENS_TEMP_ID 2490378
 fi

+param set-default EKF2_BARO_DELAY 39
+param set-default EKF2_BARO_NOISE 0.9
+param set-default EKF2_HGT_REF 0
+param set-default EKF2_MAG_DELAY 60
+param set-default EKF2_MAG_NOISE 0.06
 param set-default EKF2_MULTI_IMU 2
 param set-default EKF2_OF_CTRL 1
+param set-default EKF2_OF_DELAY 28
 param set-default EKF2_OF_N_MIN 0.05
 param set-default EKF2_RNG_A_HMAX 25
+param set-default EKF2_RNG_DELAY 105
+param set-default EKF2_RNG_NOISE 0.03
 param set-default EKF2_RNG_QLTY_T 0.1
+param set-default EKF2_RNG_SFE 0.03

 param set-default SENS_FLOW_RATE 150
@@ -2,7 +2,6 @@ CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
 CONFIG_BOARD_ARCHITECTURE="cortex-m7"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_MAIERTEK_MPC2520=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
 CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y
@@ -3,7 +3,6 @@ CONFIG_BOARD_ARCHITECTURE="cortex-m4"
 CONFIG_BOARD_CONSTRAINED_FLASH=y
 CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_COMPILE_DEFINITIONS="-Wno-narrowing"
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BAROMETER_LPS25H=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
 CONFIG_DRIVERS_GPS=y
@@ -4,7 +4,6 @@ CONFIG_BOARD_CONSTRAINED_FLASH=y
 CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_COMPILE_DEFINITIONS="-Wno-narrowing"
 CONFIG_DRIVERS_BAROMETER_BMP388=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L1X=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI088_I2C=y
@@ -7,14 +7,12 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_COMMON_BAROMETERS=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
-CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_HEATER=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
@@ -6,7 +6,6 @@ CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
@@ -11,11 +11,9 @@ CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
-CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
@@ -194,12 +194,6 @@

 #define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2     /* ADC 1 2 3 clock source */

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

@@ -11,11 +11,9 @@ CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
-CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20649=y
@@ -195,12 +195,6 @@

 #define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2     /* ADC 1 2 3 clock source */

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

@@ -12,7 +12,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -8,7 +8,6 @@ CONFIG_BOARD_SERIAL_URT6="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
@@ -7,7 +7,6 @@ CONFIG_BOARD_SERIAL_URT6="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
@@ -12,7 +12,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -97,9 +97,9 @@
 #define INTERFACE_USART_CONFIG         "/dev/ttyS5,57600"
 #define BOOT_DELAY_ADDRESS             0x000001a0
 #define BOARD_TYPE                     1013
-#define BOARD_FLASH_SECTORS            (14)
-#define BOARD_FLASH_SIZE               (16 * 128 * 1024)
-#define APP_RESERVATION_SIZE 	       (1 * 128 * 1024)
+#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
+#define BOARD_FLASH_SECTORS            (15)
+#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)

 #define OSC_FREQ                       16

@@ -11,7 +11,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -11,7 +11,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -9,7 +9,6 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20689=y
@@ -9,7 +9,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -9,7 +9,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -9,7 +9,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -11,7 +11,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -7,7 +7,6 @@ CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
@@ -7,7 +7,6 @@ CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
@@ -8,7 +8,6 @@ CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
@@ -12,7 +12,6 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -12,7 +12,6 @@ CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
@@ -12,7 +12,6 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -6,5 +6,4 @@
 param set-default BAT1_V_DIV 10.1
 param set-default BAT1_A_PER_V 17

-param set-default GPS_2_CONFIG 202
 param set-default TEL_FRSKY_CONFIG 103
@@ -197,12 +197,6 @@

 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

@@ -10,7 +10,6 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -9,7 +9,6 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -10,7 +10,6 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -197,12 +197,6 @@

 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

@@ -10,7 +10,6 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
@@ -196,12 +196,6 @@

 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

@@ -9,11 +9,9 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
-CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
-CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI085=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI088=y
@@ -196,12 +196,6 @@

 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY

-/* UART clock selection */
-/* reset to default to overwrite any changes done by any bootloader */
-
-#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
-#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
-
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2

--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
Matthias Grob	1d5d96e8f9	mavlink: return unsupported frame result when that's the case	2024-05-02 17:32:37 +02:00
Matthias Grob	3b21f3999f	mavlink: spacing, naming of command frame handling	2024-05-02 17:30:59 +02:00
Matthias Grob	6dbf39be7c	Update MAVLink to contain _INT frame deprecation warning	2024-05-02 17:19:31 +02:00
Daniel Agar	3bd14fcb16	mavlink: COMMAND_INT receiver reject unsupported MAV_FRAMEs	2024-05-02 16:49:37 +02:00
Daniel Agar	ed35155b50	vehicle_command: add initial frame support (GLOBAL & GLOBAL_RELATIVE_ALT)	2024-05-02 16:49:37 +02:00
David Sidrane	c13e3bae12	px4_fmu-v6xrt:Support_MMCSD_MULTIBLOCK with preflight	2024-05-01 20:45:42 -04:00
David Sidrane	a3e1dcce4b	NuttX with imxrt_sd-preflight backport	2024-05-01 20:45:42 -04:00
Daniel Agar	33234f4dc0	drivers/ins/vectornav: add missing sensor_gps velocity magnitude	2024-05-01 20:40:28 -04:00
Julian Oes	e79993a316	gps: split enum after rebase Signed-off-by: Julian Oes <julian@oes.ch>	2024-05-01 14:42:58 -04:00
alexklimaj	b308c4fbcc	boards: ark rtk gps safety led open drain	2024-05-01 14:42:58 -04:00
alexklimaj	c90ccabbe0	gps: add ZED-F9P-15B	2024-05-01 14:42:58 -04:00
alexklimaj	2498ce6a5c	boards: add iis2mdc mag to ark pi6x	2024-04-30 21:26:42 -04:00
alexklimaj	67b39314bf	boards: update ark_pi6x EKF delays	2024-04-30 21:26:42 -04:00
Daniel Agar	b6da0b141d	ekf2: GPS yaw only invalidate yaw_align if stopping due to fusion failure	2024-04-29 21:04:21 -04:00
Beat Küng	547209e1dc	libevents: update submodule And remove obsolete libevents_definitions.h	2024-04-29 07:22:40 -07:00
bresch	9dc7719d4a	ekf2: Only reset to GNSS heading if necessary When North-East (e.g.: GNSS pos/vel) aiding is active, the heading estimate is constrained and consistent with the vel/pos aiding. Reset to GNSS heading should only occur if no N-E aiding is active or if the filter is not yes aligned. Otherwise, just wait for the consistency check to pass again (will pass at some point if the heading uncertainty of the filter is getting too high).	2024-04-29 07:22:01 -07:00
Jukka Laitinen	6435e25929	commander: Use PX4_STACK_ADJUSTED to increase stack for 64-bit targets Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>	2024-04-29 08:11:54 +02:00
Hamish Willee	902712b97f	LogMessage.msg - expand out descriptive string (#23054 )	2024-04-29 14:02:09 +12:00
Peter van der Perk	500332e424	imxrt: flexpwm remove 1:1 mapping requirement	2024-04-27 07:57:32 -04:00
Silvan Fuhrer	34cb69898e	FW Position Controller: fix Altitude mode without valid z reference (e.g. no GPS) Signed-off-by: Silvan Fuhrer <silvan@auterion.com>	2024-04-26 10:44:40 +02:00
oravla5	f91103af6e	boards: removed CONFIG_SYSTEMCMDS_REFLECT from Sky-Drones AIRLink board support	2024-04-26 09:42:06 +02:00
oravla5	9d6ac0b87a	mavlink: Added MAV_{i}_HL_FREQ parameter	2024-04-26 09:42:06 +02:00
oravla5	2b2e1c9521	mavlink: Added parsing of CLI option to configure HL frequency	2024-04-26 09:42:06 +02:00
oravla5	e7b4c5903f	px4_cli: Added px4_get_parameter_value function overload for float type	2024-04-26 09:42:06 +02:00
bresch	7cefc3172a	estimatorCheck: get param only if handle is valid	2024-04-25 14:48:23 -04:00
murata,katsutoshi	ba448fb549	MC Auto: add fixed yaw mode	2024-04-25 13:53:05 +02:00
oravla5	98b23e41f7	mavlink: fixed compilation error after var renaming	2024-04-25 08:23:32 +02:00
oravla5	283ae60a15	telemetry: removed iridium driver	2024-04-25 08:23:32 +02:00
oravla5	3cb48feb61	high_latency_stream: minor PR fix	2024-04-25 08:23:32 +02:00
oravla5	bf1266af11	mavlink: added back gimbal v1 protocol command	2024-04-25 08:23:32 +02:00
oravla5	03652beef8	commander: fixed format	2024-04-25 08:23:32 +02:00
oravla5	d0e7f2c368	high_latency_stream: heading taken from vehicle_attitude topic	2024-04-25 08:23:32 +02:00
Igor Mišić	d0532f45b2	telemetry: enable iridium	2024-04-25 08:23:32 +02:00
Igor Mišić	61ca65d863	mavlink: use high_latency_data_link_lost as backup to normal data_link	2024-04-25 08:23:32 +02:00
Igor Mišić	4f8de500af	iridiumsbd: update logic for detecting if the modem is not responsive	2024-04-25 08:23:32 +02:00
Igor Mišić	5be0adc779	mavlink: don't send command ACK for internal commands over Iridium	2024-04-25 08:23:32 +02:00
Igor Mišić	29af189cd0	mavlink: don't send events over Iridium	2024-04-25 08:23:32 +02:00
Igor Mišić	208909d471	mavlink: use high_latency_data_link_lost as backup to normal data_link	2024-04-25 08:23:32 +02:00
Igor Mišić	de23c10b68	commander: improve handling high latency link lost/regain	2024-04-25 08:23:32 +02:00
Igor Mišić	d3b853a7f9	mavlink: fix handling of transmission enable/disable Co-authored-by: RomanBapst <bapstroman@gmail.com>	2024-04-25 08:23:32 +02:00
Igor Mišić	760bcdec2f	high_latency_stream: fixed bug where fields were not updating - topic update was checked twice in the same loop and thus the second time the topic would never indicate to have updated Co-authored-by: RomanBapst <bapstroman@gmail.com>	2024-04-25 08:23:32 +02:00
Igor Mišić	df2cc4af05	commander: fix check for availability of high latency link Signed-off-by: RomanBapst <bapstroman@gmail.com>	2024-04-25 08:23:32 +02:00
Beat Küng	f543951e10	commander: set correct health component when reporting errors	2024-04-24 16:06:32 -04:00
Jacob Dahl	69e082c83d	drivers/magnetometer: new ST IIS2MDC Magnetometer driver	2024-04-24 13:01:18 -07:00
dirksavage88	6a3e57d428	Shift vertical orientation above scaling yaw operation, cp angle sign change Signed-off-by: dirksavage88 <dirksavage88@gmail.com>	2024-04-24 15:58:12 -04:00
dirksavage88	0f6f4c5b07	fix to orientation offsets for scaled yaw, removed unused param Signed-off-by: dirksavage88 <dirksavage88@gmail.com>	2024-04-24 15:58:12 -04:00
Thomas Frans	65c7e034dc	VSCode: add EditorConfig extension to recommended and devcontainer.json	2024-04-24 15:52:23 -04:00
Daniel Agar	eb59bb9de9	simulation/gz_bridge: eliminate implicit float conversion	2024-04-24 15:51:30 -04:00
bresch	b508df39a2	imu consistency: don't scale param threshold	2024-04-24 15:51:07 -04:00
bresch	8bf1cf0b15	ekf2_params: reduce "short" description	2024-04-24 15:09:57 -04:00
Silvan Fuhrer	97191bd60f	autopilot_tester: for mission end timeout check take speed factor into account And increase the (simulation time) timeouts. Signed-off-by: Silvan Fuhrer <silvan@auterion.com>	2024-04-23 16:37:31 +02:00
Silvan Fuhrer	818e318334	autopilot_tester: reduce mission distance for wind world Signed-off-by: Silvan Fuhrer <silvan@auterion.com>	2024-04-23 16:37:31 +02:00
Silvan Fuhrer	59232c27ae	autopilot_tester: use normal VTOL mission for airspeed blockage test Signed-off-by: Silvan Fuhrer <silvan@auterion.com>	2024-04-23 16:37:31 +02:00
fury1895	2683128205	PM Selector Auterion: remove INA226_SHUNT value reset (skynode only)	2024-04-23 16:02:35 +02:00