Use kClearanceAltitudeBuffer for it, which is also used to ensure that during takeoff an
altitude setpoint above the clearance altitdue is set.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- explicitly defined takeoff airspeed setpoint
- dont use climbout mode
- allow max climb on takeoff
- dont handle post clearance altitude case (navigator will switch anyway)
- also put flaring internal states into a struct to organize a bit
- one concern with blending the throttle setpoint like this with the flare time param is that folding prop belly landing airframes may want to have a separate param for shorter throttle kill and still use the flare time ramps for everything else
abruptly changing to a heading setpoint on flare can cause the aircraft to roll and deviate from the runway, this commit
- maintains path following control during the flare not to disrupt the tracking just before touchdown
- (unfortunately for crosswind landing) removes the body axis alignment for runway bearing - this is a compromise
to achieve both runway bearing body axis alignment AND a specific touchdown point, either
1. the wind would need to be considered, and an appropriate diagonal approach (obstructions allowing) defined to the runway
2. slip control added, keeping path following outputs only commanding roll (controlling airspeed vector) and using yaw-rate command (only actuated by e.g. rudder) to align body axis with the runway
- consolidate takeoff rotation transition times for pitch constraints and throttle setpoint with a single param
- consolidate pitch takeoff constraint parameters (remove rwto_max_pitch, use nominal max)
- input correct units to rwto pitch constraint getters
- encapsulate absolute time interpolator method for transitions
- start runway ops from idle throttle
TECS climbout mode was used for takeoff climbout, which puts throttle to full and does not regulate a specific airspeed.
This commit sets the desired takeoff airspeed explicitly and allows max climb rate to track the ascent.
previously a scale factor param on min airspeed was used to define the climbout airspeed for runway takeoff
additionally, the rotation speed was defined by another hardcoded scale on top of the previously scaled min airspeed
this commit explicitly defines a takeoff speed and rotation speed for runway takeoff in params, with option to disable
* Log position setpoint reference of npfg
This commit logs the local position setpoint reference when using NPFG
* Address review comments
This commit address review comments from @tstastny
Previously the minimum airspeed setpoint was adjusted to the load_factor compensated
stall speed, which, when the stall speed was set without margin, gave the controller
no room for error (the vehicle would stall if the controller has even a small airspeed
error).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Affects the states AUTO_ALTITUDE and AUTO_CLIMBRATE. Those modes should only be entered
if armed (as they are pure failsafe modes). Also allow though to enter them even if
the position setpoint(s) are invalid, as they are not needed.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Instead of checking the .valid flag of position_setpoint, check for ISFINITE() of lat, lon, alt
when pulling the position_setpoint triplet. This fixes problems where the .valid flag didn't
reflect the proper state of the setpoint (e.g. .valid was true, .lat though NAN)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This commit fixes feedforward acceleration setpoints for fixedwing offboard position control.
Previously when acceleration feedforward inputs were sent, negative curvature accelerations were not being computed properly
If the current yaw setpoint is valid we should use it to make the transition in this direction.
For a VTOL_TAKEOFF the yaw_setpoint is used to specify the transition direction (the
vehicle is aligned towards it and then transition is started). The current yaw can be
a bit off (e.g. because MIS_YAW_ERR is large), and it is better to track the actual setpoint.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
-always reset roll/pitch/yaw integrators at the same time
-reset them while waiting for launch or during FW Takeoff before Climbout
-reset wheel rate integrator only when disarmed
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- msg constant names now comply with ROS conventions:
uppercase alphanumeric characters with underscores for separating words
partially fix#19917
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
FW_LND_USETER defaulted to 1 and FW_LND_ABORT terrain based bits all enabled. why? because using a distance sensor is critical to detecting when to flare, and we want to force the user to actively disable these safety settings if they so choose, so that they understand the implications.
- new param, FW_LND_TER_REL
- fixing the glide slope helps keep the landing glide behavior steady (avoiding bumps in the altitude setpoint from e.g. trees)
- flare is still triggered via the distance sensor, if enabled by FW_LND_USETERR
when the vehicle did not track the slope well (e.g. at an offset above the track) and the altitude setpoint flattening on intersection with terrain, the throttle would spool up to smoothly intersect the newly flattened altitude setpoint, this could happen before the flare altitude was reached, which is bad. now the steady state glide behavior will be maintained, and flare can trigger at the appropriate time
Silvan Fuhrer