* SF45 fixes to restart the state machine if sensor does not init correctly (#23565)
* fixes to restart the state machine if sensor does not init correctly
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* fixes
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* increase fail count
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* remove extra flush, switch from warn to debug, add enum states for sensor bring-up
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* remove dead code, decrease restart fail count metric, break out of loop with consec errors if over the fail count and not init
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* remove tel2 default from sf45 (#24602)
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* fix to orientation offsets for scaled yaw, removed unused param
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Shift vertical orientation above scaling yaw operation, cp angle sign change
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* SENS: RNG: SF45 changed data processing and publication design, moved to a publishing per sector design.
other minor improvements
* SENS: RNG: SF45: Fixed sf45 parser, added general checks to avoid potential out-of-bound access
* SENS: RNG: SF45:Fix startup problems, increase frequency, robust parser, use nonblocking reads
* SENS: RNG: SF45: Added timeout to sensor measurements, to compensate the lower loop time of CollisionPrevention
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Claudio Chies <61051109+Claudio-Chies@users.noreply.github.com>
Co-authored-by: Alexander Lerach <alexander@auterion.com>
* gps: heading fixes for NMEA/Unicore
This updates the GPS submodule which includes NMEA/Unicore fixes:
- Add correct return value for sat infos
- Only publish on position updates
- Request required topics at 5 Hz for Unicore
* gps: build fix
This fixes various edge cases when input is set to both: RC and
MAVLink gimbal protocol v2.
Specifically:
- We no longer immediately reset primary control if there is no update,
otherwise this will reset immediately after an commands.
- Talking of commands: GIMBAL_MANAGER_CONFIGURE no longer switches
control to MAVLink but only an actual incoming setpoint command does.
- And incoming setpoint command only triggers UpdatedActiveOnce which
means we will check RC again afterwards and if there is big movement
switch back to RC. That's the intuitive thing to do until we have
better reporting about who/what is in control.
- Also, with RC we no longer always set us to be in control but only on
major movement.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
- warn about full traffic conflict buffer at 1/60hz.
- add conflict expiry for buffer.
- use only events for buffer full warning. mavlink_log_critical no longer needed.
- use icao address for conflict warnings id, stop using uas_id. UTM_GLOBAL_POSITION assumed deprecated.
- stop spamming when buffer is full
- fix warning wording if buffer is full.
- remove UTM_GLOBAL_POSITION
Fixes failing unit test:
* [adsbTest] Reduce conflict timestamps - not enough time has passed in ci
- failed ci output - (passes locally with make tests TESTFILTER=AdsbConflict)
- Timestamp: 6000000000
- Time now: 457720038
- Time since timestamp: 0
- Old Conflict warning expired: 0
- --------------------
- adsb_conflict._traffic_state 0
- ../../src/lib/adsb/AdsbConflictTest.cpp:244: Failure
- Value of: adsb_conflict._traffic_state == TRAFFIC_STATE::REMIND_CONFLICT
- Actual: false
- Expected: true
* Made Serial API open the UART in NON BLOCKING mode
* Updated voxl_esc driver to latest from ModalAI fork
* Ported voxl_esc driver over to new Serial UART API
* Removed voxl_esc serial abstraction since new Serial API is already a serial abstraction
