* rft: clean merge to PX4
* fix: formatting
* fix: extra line
* fix: moved submarine out of "is_ground_vehicle", added proper check for center-throttle
* feat: updated gazebo models to include bluerov update
* fix: use 'is_uuv_vehicle', remove FW_MM/LLC from uuv build
* fix: added saturation to thrust and torque messages via param
* doc: updated parameters documentation for uuv
* fix: formatting
* feat: matching hardware reference
* fix: thrusters kg
* rft: removed commented lines
* fix: update gz reference given hw setup
* fix: hardware references
* fix: recommendations
* fix: updated settings to match hardware
* rft: check only for fixed and rotary wing for high throttle
Co-authored-by: Daniel Agar <daniel@agar.ca>
* fix: commit oupsie
* fix: format
* rft: remove is_uuv
* fix: hw parameters, uuv build target for v6x
* feat: added support for D-pad attitude changes in stabilized position control
* fix: position setpoint update and parametrized trajectory age and att change
* fix: format
* fix: removed duplicated call to check_validity_setpoint
* fix: setpoint update on arming logic
* fix: setpoint initialization for stabilized mode
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
* feat: configurable board pwm freq from Kconfig
* feat: add board_pwm_config to submenu
* fix: define sequence correction
* fix: revert Tools/simulation/gz
* fix: track upstream gz
* fix: track upstream mavlink
* feat: adjustable pwm for multiple board types
* feat: add conditional check for CONFIG_ for correct fallback
* add: spacecraft board with correct BOARD_PWM_FREQ supporting 10Hz actuation rate
* fix: set dependencies for submenu arch chips
* fix: keep only upper arch level
* fix: proper checking - still not showing up for board config
* feat: add hidden kconfig for platforms
* Merge Nuttx config into px4board
Allows to expose nuttx into PX4 if needed
* Kconfig: Include nuttx symbols in updateconfig
Only if applicable i.e. defined in the kconfig
* fix: merged config with previously generated boardconfig
* doc: updated code comment
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
* Added various features to flash analysis (also run with FLASH overflow, summary in comment output, newer bloaty version, only add comment if change is large enough, ...)
* Added feedback from review
* Use wildcards
* Removed backward-compat logic and use correct base
This resets the USARTs' clock source selection to the default, in case
it has been changed by the bootloader.
This is required if booting from the ArduPilot bootloader which happens
to reset the clock selection to PLL.
Without this fix, UARTs (including the console) is garbled, so
presumably at an invalid baudrate.
* Update Zenoh-pico from 0.7.0 to 1.0.0
* Update the zenoh-pico version to use PX4/dev/1.0.0-px4
* Remove the rostopic and rt/ prefix
* Unlike zenoh-bridge-dds we were using, zenoh-bridge-ros2dds is now adding the rt/ prefix automagically.
192.168.0.x is often used by routers for WIFI/ethernet networks, and thus
can create conflicts.
This can happen for example if a companion is connected to the FMU via
ethernet and at the same time connects to a WIFI network as DHCP client.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
When flow control is used together with DMA, we need to add a pulldown
to CTS. Without it, it assumes flow control and gets stuck when
CTS is not connected.
Signed-off-by: Julian Oes <julian@oes.ch>
Alexander Lerach