The case where the airframe maintainer wants to enforce a reset to airframe is
not covered anymore with the `param set-default` mechanism. For products based
on PX4 this is still required to ensure proper functionality after a major update.
- gz in PX4/Firmware (0c18d43657b1b7279b8dce78a6014243cc14d1e2): d754381a1c
- gz current upstream: 881558c8c2
- Changes: d754381a1c...881558c8c2
881558c 2024-05-29 Jacob Dahl - new lidar_v2 model and x500_lidar vehicle
Having a generic interface over the GPS drivers makes dedicated
functionality for each driver harder. Move the Septentrio driver into
its own module under the `gnss` driver directory, and let it have its
own parameters for only the functionality it requires. This also helps
with adding new features because they only need to be implemented for
the driver that wants it, simplifying testing.
- these are old RC switch configuration parameters that haven't been used for
years, but were hardcoded into old versions of QGC
- RC_MAP_RATT_SW, RC_MAP_POSCTL_SW, RC_MAP_ACRO_SW, RC_MAP_STAB_SW, RC_MAP_MAN_SW deleted
-
* ist8310: do reset before WHOAMI call
Apparently, the IST8310's WHOAMI register is writeable. Presumably, this
can get corrupted by bus noise. It is only reset if powered off for 30s.
Therefore, we do a reset before doing the WHOAMI.
* ist8310: improve comment
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
---------
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Compared to GNSS, alternate position observation methods are less accurate
and thus generally not good enough to do airspeed validation with.
Airspeed validation is thus disabled if no GNSS fusion is happening.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* AirspeedValidator: remove additional one second of hysteresis for triggering
innovation checks
- this check already uses an integrator and so adding more delay just makes
log analysis more difficult and does not really add any value
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* removed unnecessary conditions
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* AirspeedValidator: only disable innov checks if ASPD_FS_INTEG is negative
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* get rid of unnecessary check on innovation threshold parameter
Signed-off-by: RomanBapst <bapstroman@gmail.com>
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
* update GCS connection loss failsafe in all gazebo models
Signed-off-by: frederik <frederik@auterion.com>
* cleanup and return of old parameter
Signed-off-by: frederik <frederik@auterion.com>
---------
Signed-off-by: frederik <frederik@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
This fixes various edge cases when input is set to both: RC and
MAVLink gimbal protocol v2.
Specifically:
- We no longer immediately reset primary control if there is no update,
otherwise this will reset immediately after an commands.
- Talking of commands: GIMBAL_MANAGER_CONFIGURE no longer switches
control to MAVLink but only an actual incoming setpoint command does.
- And incoming setpoint command only triggers UpdatedActiveOnce which
means we will check RC again afterwards and if there is big movement
switch back to RC. That's the intuitive thing to do until we have
better reporting about who/what is in control.
- Also, with RC we no longer always set us to be in control but only on
major movement.
192.168.0.x is often used by routers for WIFI/ethernet networks, and thus
can create conflicts.
This can happen for example if a companion is connected to the FMU via
ethernet and at the same time connects to a WIFI network as DHCP client.
