Update platforms/nuttx/src/bootloader/stm/stm32_common/main.c

* boards: ark fpv add SCH16T

* boards: ark fpv fix spi6

.ci/Jenkinsfile-compile

@@ -46,8 +46,10 @@ pipeline {
                      "ark_cannode_default",
                      "ark_fmu-v6x_bootloader",
                      "ark_fmu-v6x_default",
+                     "ark_fpv_bootloader",
+                     "ark_fpv_default",
                      "ark_pi6x_bootloader",
-                     "ark_pi6x_default"
+                     "ark_pi6x_default",
                      "atl_mantis-edu_default",
                      "av_x-v1_default",
                      "bitcraze_crazyflie21_default",

.vscode/cmake-variants.yaml

@@ -181,6 +181,16 @@ CONFIG:
       buildType: MinSizeRel
       settings:
         CONFIG: ark_fmu-v6x_default
+    ark_fpv_bootloader:
+      short: ark_fpv_bootloader
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_fpv_bootloader
+    ark_fpv_default:
+      short: ark_fpv_default
+      buildType: MinSizeRel
+      settings:
+        CONFIG: ark_fpv_default
     ark_pi6x_bootloader:
       short: ark_pi6x_bootloader
       buildType: MinSizeRel

CMakeLists.txt

@@ -1,6 +1,6 @@
 ############################################################################
 #
-# Copyright (c) 2017 - 2022 PX4 Development Team. All rights reserved.
+# Copyright (c) 2017 - 2024 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -132,7 +132,9 @@ list(GET VERSION_LIST 2 PX4_VERSION_PATCH)
 string(REPLACE "-" ";" PX4_VERSION_PATCH ${PX4_VERSION_PATCH})
 list(GET PX4_VERSION_PATCH 0 PX4_VERSION_PATCH)
 
-message(STATUS "PX4 version: ${PX4_GIT_TAG} (${PX4_VERSION_MAJOR}.${PX4_VERSION_MINOR}.${PX4_VERSION_PATCH})")
+# # Capture only the hash part after 'g'
+string(REGEX MATCH "g([a-f0-9]+)$" GIT_HASH "${PX4_GIT_TAG}")
+set(PX4_GIT_HASH ${CMAKE_MATCH_1})
 
 define_property(GLOBAL PROPERTY PX4_MODULE_LIBRARIES
                  BRIEF_DOCS "PX4 module libs"

Makefile

@@ -1,6 +1,6 @@
 ############################################################################
 #
-# Copyright (c) 2015 - 2020 PX4 Development Team. All rights reserved.
+# Copyright (c) 2015 - 2024 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -323,7 +323,33 @@ px4io_update:
 	cp build/cubepilot_io-v2_default/cubepilot_io-v2_default.bin boards/cubepilot/cubeyellow/extras/cubepilot_io-v2_default.bin
 	git status
 
-bootloaders_update: ark_fmu-v6x_bootloader cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader holybro_kakuteh7_bootloader matek_h743_bootloader matek_h743-mini_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6c_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
+bootloaders_update: \
+	ark_fmu-v6x_bootloader \
+	ark_fpv_bootloader \
+	ark_pi6x_bootloader \
+	cuav_nora_bootloader \
+	cuav_x7pro_bootloader \
+	cubepilot_cubeorange_bootloader \
+	cubepilot_cubeorangeplus_bootloader \
+	hkust_nxt-dual_bootloader \
+	hkust_nxt-v1_bootloader \
+	holybro_durandal-v1_bootloader \
+	holybro_kakuteh7_bootloader \
+	holybro_kakuteh7mini_bootloader \
+	holybro_kakuteh7v2_bootloader \
+	matek_h743_bootloader \
+	matek_h743-mini_bootloader \
+	matek_h743-slim_bootloader \
+	modalai_fc-v2_bootloader \
+	mro_ctrl-zero-classic_bootloader \
+	mro_ctrl-zero-h7_bootloader \
+	mro_ctrl-zero-h7-oem_bootloader \
+	mro_pixracerpro_bootloader \
+	px4_fmu-v6c_bootloader \
+	px4_fmu-v6u_bootloader \
+	px4_fmu-v6x_bootloader \
+	px4_fmu-v6xrt_bootloader \
+	siyi_n7_bootloader
 	git status
 
 .PHONY: coverity_scan

ROMFS/px4fmu_common/init.d/rcS

@@ -439,6 +439,14 @@ else
 	# Must be started after the serial config is read
 	rc_input start $RC_INPUT_ARGS
 
+	# Manages USB interface
+	if ! cdcacm_autostart start
+	then
+		sercon
+		echo "Starting MAVLink on /dev/ttyACM0"
+		mavlink start -d /dev/ttyACM0
+	fi
+
 	#
 	# Play the startup tune (if not disabled or there is an error)
 	#

Tools/px_uploader.py

@@ -1,7 +1,7 @@
 #!/usr/bin/env python3
 ############################################################################
 #
-#   Copyright (c) 2012-2017 PX4 Development Team. All rights reserved.
+#   Copyright (c) 2012-2024 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -50,9 +50,6 @@
 #       Currently only used for informational purposes.
 #
 
-# for python2.7 compatibility
-from __future__ import print_function
-
 import sys
 import argparse
 import binascii
@@ -70,35 +67,32 @@ from sys import platform as _platform
 try:
     import serial
 except ImportError as e:
-    print("Failed to import serial: " + str(e))
+    print(f"Failed to import serial: {e}")
     print("")
     print("You may need to install it using:")
-    print("    pip3 install --user pyserial")
+    print("    python -m pip install pyserial")
     print("")
     sys.exit(1)
 
 
-# Define time to use time.time() by default
-def _time():
-    return time.time()
-
 # Detect python version
 if sys.version_info[0] < 3:
-    runningPython3 = False
-else:
-    runningPython3 = True
-    if sys.version_info[1] >=3:
-        # redefine to use monotonic time when available
-        def _time():
-            try:
-                return time.monotonic()
-            except Exception:
-                return time.time()
+    raise RuntimeError("Python 2 is not supported. Please try again using Python 3.")
+    sys.exit(1)
+
+
+# Use monotonic time where available
+def _time():
+    try:
+        return time.monotonic()
+    except Exception:
+        return time.time()
 
 class FirmwareNotSuitableException(Exception):
     def __init__(self, message):
         super(FirmwareNotSuitableException, self).__init__(message)
 
+
 class firmware(object):
     '''Loads a firmware file'''
 
@@ -163,13 +157,13 @@ class firmware(object):
 
     def crc(self, padlen):
         state = self.__crc32(self.image, int(0))
-        for i in range(len(self.image), (padlen - 1), 4):
+        for _ in range(len(self.image), (padlen - 1), 4):
             state = self.__crc32(self.crcpad, state)
         return state
 
 
-class uploader(object):
-    '''Uploads a firmware file to the PX FMU bootloader'''
+class uploader:
+    '''Uploads a firmware file to the PX4 bootloader'''
 
     # protocol bytes
     INSYNC          = b'\x12'
@@ -195,6 +189,8 @@ class uploader(object):
     GET_CHIP        = b'\x2c'     # rev5+  , get chip version
     SET_BOOT_DELAY  = b'\x2d'     # rev5+  , set boot delay
     GET_CHIP_DES    = b'\x2e'     # rev5+  , get chip description in ASCII
+    GET_VERSION     = b'\x2f'     # rev5+  , get chip description in ASCII
+    CHIP_FULL_ERASE = b'\x40'     # full erase of flash, rev6+
     MAX_DES_LENGTH  = 20
 
     REBOOT          = b'\x30'
@@ -205,6 +201,7 @@ class uploader(object):
     INFO_BOARD_ID   = b'\x02'        # board type
     INFO_BOARD_REV  = b'\x03'        # board revision
     INFO_FLASH_SIZE = b'\x04'        # max firmware size in bytes
+    BL_VERSION      = b'\x07'        # get bootloader version, e.g. major.minor.patch.githash (up to 20 chars)
 
     PROG_MULTI_MAX  = 252            # protocol max is 255, must be multiple of 4
     READ_MULTI_MAX  = 252            # protocol max is 255
@@ -235,6 +232,7 @@ class uploader(object):
         self.baudrate_bootloader = baudrate_bootloader
         self.baudrate_flightstack = baudrate_flightstack
         self.baudrate_flightstack_idx = -1
+        self.force_erase = False
 
     def close(self):
         if self.port is not None:
@@ -357,19 +355,22 @@ class uploader(object):
             self.port.baudrate = self.baudrate_bootloader * 2.33
         except NotImplementedError as e:
             # This error can occur because pySerial on Windows does not support odd baudrates
-            print(str(e) + " -> could not check for FTDI device, assuming USB connection")
+            print(f"{e} -> could not check for FTDI device, assuming USB connection")
             return
 
         self.__send(uploader.GET_SYNC +
                     uploader.EOC)
         try:
             self.__getSync(False)
-        except:
+        except RuntimeError:
             # if it fails we are on a real serial port - only leave this enabled on Windows
             if sys.platform.startswith('win'):
                 self.ackWindowedMode = True
         finally:
-            self.port.baudrate = self.baudrate_bootloader
+            try:
+                self.port.baudrate = self.baudrate_bootloader
+            except Exception:
+                pass
 
     # send the GET_DEVICE command and wait for an info parameter
     def __getInfo(self, param):
@@ -410,6 +411,17 @@ class uploader(object):
         pieces = value.split(b",")
         return pieces
 
+    def __getVersion(self):
+        self.__send(uploader.GET_VERSION + uploader.EOC)
+        try:
+            length = self.__recv_int()
+            value = self.__recv(length)
+            self.__getSync()
+        except RuntimeError:
+            # Bootloader doesn't support version call
+            return "unknown"
+        return value.decode()
+
     def __drawProgressBar(self, label, progress, maxVal):
         if maxVal < progress:
             progress = maxVal
@@ -421,10 +433,16 @@ class uploader(object):
 
     # send the CHIP_ERASE command and wait for the bootloader to become ready
     def __erase(self, label):
-        print("Windowed mode: %s" % self.ackWindowedMode)
+        print(f"Windowed mode: {self.ackWindowedMode}")
         print("\n", end='')
-        self.__send(uploader.CHIP_ERASE +
-                    uploader.EOC)
+
+        if self.force_erase:
+            print("Trying force erase of full chip...\n")
+            self.__send(uploader.CHIP_FULL_ERASE +
+                        uploader.EOC)
+        else:
+            self.__send(uploader.CHIP_ERASE +
+                        uploader.EOC)
 
         # erase is very slow, give it 30s
         deadline = _time() + 30.0
@@ -441,9 +459,14 @@ class uploader(object):
 
             if self.__trySync():
                 self.__drawProgressBar(label, 10.0, 10.0)
+                if self.force_erase:
+                    print("\nForce erase done.\n")
                 return
 
-        raise RuntimeError("timed out waiting for erase")
+        if self.force_erase:
+            raise RuntimeError("timed out waiting for erase, force erase is likely not supported by bootloader!")
+        else:
+            raise RuntimeError("timed out waiting for erase")
 
     # send a PROG_MULTI command to write a collection of bytes
     def __program_multi(self, data, windowMode):
@@ -581,8 +604,11 @@ class uploader(object):
         self.board_rev = self.__getInfo(uploader.INFO_BOARD_REV)
         self.fw_maxsize = self.__getInfo(uploader.INFO_FLASH_SIZE)
 
+        self.version = self.__getVersion()
+
     # upload the firmware
-    def upload(self, fw_list, force=False, boot_delay=None, boot_check=False):
+    def upload(self, fw_list, force=False, boot_delay=None, boot_check=False, force_erase=False):
+        self.force_erase = force_erase
         # select correct binary
         found_suitable_firmware = False
         for file in fw_list:
@@ -611,6 +637,8 @@ class uploader(object):
         print("Loaded firmware for board id: %s,%s size: %d bytes (%.2f%%) " % (fw.property('board_id'), fw.property('board_revision'), fw.property('image_size'), percent))
         print()
 
+        print(f"Bootloader version: {self.version}")
+
         # Make sure we are doing the right thing
         start = _time()
         if self.board_type != fw.property('board_id'):
@@ -640,14 +668,14 @@ class uploader(object):
             self.otp_coa = self.otp[32:160]
             # show user:
             try:
-                print("sn: ", end='')
+                print("Sn: ", end='')
                 for byte in range(0, 12, 4):
                     x = self.__getSN(byte)
                     x = x[::-1]  # reverse the bytes
                     self.sn = self.sn + x
                     print(binascii.hexlify(x).decode('Latin-1'), end='')  # show user
                 print('')
-                print("chip: %08x" % self.__getCHIP())
+                print("Chip: %08x" % self.__getCHIP())
 
                 otp_id = self.otp_id.decode('Latin-1')
                 if ("PX4" in otp_id):
@@ -657,17 +685,19 @@ class uploader(object):
                     print("OTP pid: " + binascii.hexlify(self.otp_pid).decode('Latin-1'))
                     print("OTP coa: " + binascii.b2a_base64(self.otp_coa).decode('Latin-1'))
 
-            except Exception:
+            except Exception as e:
                 # ignore bad character encodings
+                print(f"Exception ignored: {e}")
                 pass
 
         # Silicon errata check was added in v5
         if (self.bl_rev >= 5):
             des = self.__getCHIPDes()
             if (len(des) == 2):
-                print("family: %s" % des[0])
-                print("revision: %s" % des[1])
-                print("flash: %d bytes" % self.fw_maxsize)
+                family, revision = des
+                print(f"Family: {family.decode()}")
+                print(f"Revision: {revision.decode()}")
+                print(f"Flash: {self.fw_maxsize} bytes")
 
                 # Prevent uploads where the maximum image size of the board config is smaller than the flash
                 # of the board. This is a hint the user chose the wrong config and will lack features
@@ -678,8 +708,7 @@ class uploader(object):
                 # https://github.com/PX4/Firmware/blob/master/src/drivers/boards/common/stm32/board_mcu_version.c#L125-L144
 
                 if self.fw_maxsize > fw.property('image_maxsize') and not force:
-                    raise RuntimeError("Board can accept larger flash images (%u bytes) than board config (%u bytes). Please use the correct board configuration to avoid lacking critical functionality."
-                                       % (self.fw_maxsize, fw.property('image_maxsize')))
+                    raise RuntimeError(f"Board can accept larger flash images ({self.fw_maxsize} bytes) than board config ({fw.property('image_maxsize')} bytes). Please use the correct board configuration to avoid lacking critical functionality.")
         else:
             # If we're still on bootloader v4 on a Pixhawk, we don't know if we
             # have the silicon errata and therefore need to flash px4_fmu-v2
@@ -780,16 +809,13 @@ class uploader(object):
 
 
 def main():
-    # Python2 is EOL
-    if not runningPython3:
-        raise RuntimeError("Python 2 is not supported. Please try again using Python 3.")
-
     # Parse commandline arguments
     parser = argparse.ArgumentParser(description="Firmware uploader for the PX autopilot system.")
     parser.add_argument('--port', action="store", required=True, help="Comma-separated list of serial port(s) to which the FMU may be attached")
     parser.add_argument('--baud-bootloader', action="store", type=int, default=115200, help="Baud rate of the serial port (default is 115200) when communicating with bootloader, only required for true serial ports.")
     parser.add_argument('--baud-flightstack', action="store", default="57600", help="Comma-separated list of baud rate of the serial port (default is 57600) when communicating with flight stack (Mavlink or NSH), only required for true serial ports.")
     parser.add_argument('--force', action='store_true', default=False, help='Override board type check, or silicon errata checks and continue loading')
+    parser.add_argument('--force-erase', action="store_true", help="Do not perform the blank check, always erase every sector of the application space")
     parser.add_argument('--boot-delay', type=int, default=None, help='minimum boot delay to store in flash')
     parser.add_argument('--use-protocol-splitter-format', action='store_true', help='use protocol splitter format for reboot')
     parser.add_argument('firmware', action="store", nargs='+', help="Firmware file(s)")
@@ -867,9 +893,10 @@ def main():
                         # Windows, don't open POSIX ports
                         if "/" not in port:
                             up = uploader(port, args.baud_bootloader, baud_flightstack)
-                except Exception:
+                except Exception as e:
                     # open failed, rate-limit our attempts
                     time.sleep(0.05)
+                    print(f"Exception ignored: {e}")
 
                     # and loop to the next port
                     continue
@@ -884,10 +911,10 @@ def main():
                         up.identify()
                         found_bootloader = True
                         print()
-                        print("Found board id: %s,%s bootloader version: %s on %s" % (up.board_type, up.board_rev, up.bl_rev, port))
+                        print(f"Found board id: {up.board_type},{up.board_rev} bootloader protocol revision {up.bl_rev} on {port}")
                         break
 
-                    except Exception:
+                    except (RuntimeError, serial.SerialException):
 
                         if not up.send_reboot(args.use_protocol_splitter_format):
                             break
@@ -907,14 +934,14 @@ def main():
 
                 try:
                     # ok, we have a bootloader, try flashing it
-                    up.upload(args.firmware, force=args.force, boot_delay=args.boot_delay)
+                    up.upload(args.firmware, force=args.force, boot_delay=args.boot_delay, force_erase=args.force_erase)
 
                     # if we made this far without raising exceptions, the upload was successful
                     successful = True
 
-                except RuntimeError as ex:
+                except RuntimeError as e:
                     # print the error
-                    print("\nERROR: %s" % ex.args)
+                    print(f"\n\nError: {e}")
 
                 except FirmwareNotSuitableException:
                     unsuitable_board = True

boards/airmind/mindpx-v2/default.px4board

@@ -12,6 +12,7 @@ CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y

boards/ark/fmu-v6x/default.px4board

@@ -8,6 +8,7 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
 CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y

boards/ark/fpv/bootloader.px4board

@@ -0,0 +1,3 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ROMFSROOT=""

boards/ark/fpv/default.px4board

@@ -0,0 +1,74 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS0"
+CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS5"
+CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS6"
+CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_DRIVERS_BAROMETER_BMP388=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
+CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
+CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_HEATER=y
+CONFIG_DRIVERS_IMU_INVENSENSE_IIM42653=y
+CONFIG_DRIVERS_IMU_MURATA_SCH16T=y
+CONFIG_COMMON_LIGHT=y
+CONFIG_COMMON_MAGNETOMETER=y
+CONFIG_DRIVERS_PWM_OUT=y
+CONFIG_COMMON_RC=y
+CONFIG_DRIVERS_UAVCAN=y
+CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=2
+CONFIG_MODULES_AIRSPEED_SELECTOR=y
+CONFIG_MODULES_BATTERY_STATUS=y
+CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
+CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_ESC_BATTERY=y
+CONFIG_MODULES_EVENTS=y
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_GYRO_FFT=y
+CONFIG_MODULES_LAND_DETECTOR=y
+CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+CONFIG_MODULES_LOAD_MON=y
+CONFIG_MODULES_LOGGER=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_MANUAL_CONTROL=y
+CONFIG_MODULES_MAVLINK=y
+CONFIG_MAVLINK_DIALECT="development"
+CONFIG_MODULES_MC_ATT_CONTROL=y
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+CONFIG_MODULES_MC_POS_CONTROL=y
+CONFIG_MODULES_MC_RATE_CONTROL=y
+CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODULES_RC_UPDATE=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_MODULES_UXRCE_DDS_CLIENT=y
+CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
+CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_LED_CONTROL=y
+CONFIG_SYSTEMCMDS_MFT=y
+CONFIG_SYSTEMCMDS_MTD=y
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SD_BENCH=y
+CONFIG_SYSTEMCMDS_SD_STRESS=y
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y

boards/ark/fpv/firmware.prototype

@@ -0,0 +1,13 @@
+{
+    "board_id": 59,
+    "magic": "ARKFPVFWv1",
+    "description": "Firmware for the ARKFPV board",
+    "image": "",
+    "build_time": 0,
+    "summary": "ARKFPV",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 1835008,
+    "git_identity": "",
+    "board_revision": 0
+}

boards/ark/fpv/init/rc.board_defaults

@@ -0,0 +1,37 @@
+#!/bin/sh
+#
+# board specific defaults
+#------------------------------------------------------------------------------
+
+# transision from params file to flash-based params (2022-08)
+if [ -f $PARAM_FILE ]
+then
+	param load $PARAM_FILE
+	param save
+	# create a backup
+	mv $PARAM_FILE ${PARAM_FILE}.bak
+	reboot
+fi
+
+# TODO: Tune the following parameters
+param set-default SENS_EN_THERMAL 1
+param set-default SENS_IMU_TEMP 10.0
+#param set-default SENS_IMU_TEMP_FF 0.0
+#param set-default SENS_IMU_TEMP_I 0.025
+#param set-default SENS_IMU_TEMP_P 1.0
+
+if ver hwtypecmp ARKFPV000
+then
+	param set-default SENS_TEMP_ID 3014666
+fi
+
+param set-default BAT1_V_DIV 21.0
+
+param set-default RC_CRSF_PRT_CFG 300
+param set-default RC_SBUS_PRT_CFG 0
+
+param set-default IMU_GYRO_DNF_EN 3
+
+# Single IMU
+param set-default EKF2_MULTI_IMU 0
+param set-default SENS_IMU_MODE 1

boards/ark/fpv/init/rc.board_sensors

@@ -0,0 +1,18 @@
+#!/bin/sh
+#
+# ARKFPV specific board sensors init
+#------------------------------------------------------------------------------
+
+board_adc start
+
+if ver hwtypecmp ARKFPV000
+then
+	# Internal SPI bus IIM42653
+	iim42653 -R 14 -s -b 1 start
+fi
+
+# Internal magnetometer on I2C
+iis2mdc -R 0 -I -b 4 start
+
+# Internal Baro on I2C
+bmp388 -I -b 2 start

boards/ark/fpv/nuttx-config/Kconfig

@@ -0,0 +1,17 @@
+#
+# For a description of the syntax of this configuration file,
+# see misc/tools/kconfig-language.txt.
+#
+config BOARD_HAS_PROBES
+	bool "Board provides GPIO or other Hardware for signaling to timing analyze."
+	default y
+	---help---
+		This board provides GPIO FMU-CH1-5, CAP1-6 as PROBE_1-11 to provide timing signals from selected drivers.
+
+config BOARD_USE_PROBES
+	bool "Enable the use the board provided FMU-CH1-5, CAP1-6 as PROBE_1-11"
+	default n
+	depends on BOARD_HAS_PROBES
+
+	---help---
+		Select to use GPIO FMU-CH1-5, CAP1-6  to provide timing signals from selected drivers.

boards/ark/fpv/nuttx-config/bootloader/defconfig

@@ -0,0 +1,95 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DEV_CONSOLE is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_SPI_EXCHANGE is not set
+# CONFIG_STM32H7_SYSCFG is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/fpv/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="ark"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743II=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=768
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARD_INITTHREAD_PRIORITY=254
+CONFIG_BOARD_LATE_INITIALIZE=y
+CONFIG_BOARD_LOOPSPERMSEC=95150
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x003B
+CONFIG_CDCACM_PRODUCTSTR="ARK BL FPV.x"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x3185
+CONFIG_CDCACM_VENDORSTR="ARK"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEBUG_TCBINFO=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FDCLONE_DISABLE=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_INIT_ENTRYPOINT="bootloader_main"
+CONFIG_INIT_STACKSIZE=3194
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SPI=y
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=32
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_UART7=y
+CONFIG_SYSTEMTICK_HOOK=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGINT_CHAR=0x03
+CONFIG_TTY_SIGTSTP=y
+CONFIG_UART7_RXBUFSIZE=512
+CONFIG_UART7_RXDMA=y
+CONFIG_UART7_TXBUFSIZE=512
+CONFIG_UART7_TXDMA=y
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000

boards/ark/fpv/nuttx-config/include/board.h

@@ -0,0 +1,507 @@
+/************************************************************************************
+ * nuttx-configs/px4_fmu-v6x/include/board.h
+ *
+ *   Copyright (C) 2016-2024 Gregory Nutt. All rights reserved.
+ *   Authors: David Sidrane <david.sidrane@nscdg.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+#ifndef __NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H
+#define __NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include "board_dma_map.h"
+
+#include <nuttx/config.h>
+
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+
+#include "stm32_rcc.h"
+#include "stm32_sdmmc.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+/* The px4_fmu-v6X  board provides the following clock sources:
+ *
+ *   X1: 16 MHz crystal for HSE
+ *
+ * So we have these clock source available within the STM32
+ *
+ *   HSI: 16 MHz RC factory-trimmed
+ *   HSE: 16 MHz crystal for HSE
+ */
+
+#define STM32_BOARD_XTAL        16000000ul
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+#define STM32_LSE_FREQUENCY     32768
+
+/* Main PLL Configuration.
+ *
+ * PLL source is HSE = 16,000,000
+ *
+ * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
+ * Subject to:
+ *
+ *     1 <= PLLM <= 63
+ *     4 <= PLLN <= 512
+ *   150 MHz <= PLL_VCOL <= 420MHz
+ *   192 MHz <= PLL_VCOH <= 836MHz
+ *
+ * SYSCLK  = PLL_VCO / PLLP
+ * CPUCLK  = SYSCLK / D1CPRE
+ * Subject to
+ *
+ *   PLLP1   = {2, 4, 6, 8, ..., 128}
+ *   PLLP2,3 = {2, 3, 4, ..., 128}
+ *   CPUCLK <= 480 MHz
+ */
+
+#define STM32_BOARD_USEHSE
+
+#define STM32_PLLCFG_PLLSRC      RCC_PLLCKSELR_PLLSRC_HSE
+
+/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR
+ *
+ *   PLL1_VCO = (16,000,000 / 1) * 40 = 640 MHz
+ *
+ *   PLL1P = PLL1_VCO/2  = 640 MHz / 2   = 320 MHz
+ *   PLL1Q = PLL1_VCO/4  = 640 MHz / 4   = 160 MHz
+ *   PLL1R = PLL1_VCO/8  = 640 MHz / 8   = 80 MHz
+ */
+
+#define STM32_PLLCFG_PLL1CFG    (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVP1EN | \
+				 RCC_PLLCFGR_DIVQ1EN | \
+				 RCC_PLLCFGR_DIVR1EN)
+#define STM32_PLLCFG_PLL1M       RCC_PLLCKSELR_DIVM1(1)
+#define STM32_PLLCFG_PLL1N       RCC_PLL1DIVR_N1(40)
+#define STM32_PLLCFG_PLL1P       RCC_PLL1DIVR_P1(2)
+#define STM32_PLLCFG_PLL1Q       RCC_PLL1DIVR_Q1(4)
+#define STM32_PLLCFG_PLL1R       RCC_PLL1DIVR_R1(8)
+
+#define STM32_VCO1_FREQUENCY     ((STM32_HSE_FREQUENCY / 1) * 40)
+#define STM32_PLL1P_FREQUENCY    (STM32_VCO1_FREQUENCY / 2)
+#define STM32_PLL1Q_FREQUENCY    (STM32_VCO1_FREQUENCY / 4)
+#define STM32_PLL1R_FREQUENCY    (STM32_VCO1_FREQUENCY / 8)
+
+/* PLL2 */
+
+#define STM32_PLLCFG_PLL2CFG     (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \
+				  RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \
+				  RCC_PLLCFGR_DIVP2EN | \
+				  RCC_PLLCFGR_DIVQ2EN | \
+				  RCC_PLLCFGR_DIVR2EN)
+#define STM32_PLLCFG_PLL2M       RCC_PLLCKSELR_DIVM2(4)
+#define STM32_PLLCFG_PLL2N       RCC_PLL2DIVR_N2(48)
+#define STM32_PLLCFG_PLL2P       RCC_PLL2DIVR_P2(2)
+#define STM32_PLLCFG_PLL2Q       RCC_PLL2DIVR_Q2(2)
+#define STM32_PLLCFG_PLL2R       RCC_PLL2DIVR_R2(2)
+
+#define STM32_VCO2_FREQUENCY     ((STM32_HSE_FREQUENCY / 4) * 48)
+#define STM32_PLL2P_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2Q_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2R_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+
+/* PLL3 */
+
+#define STM32_PLLCFG_PLL3CFG    (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVQ3EN)
+#define STM32_PLLCFG_PLL3M      RCC_PLLCKSELR_DIVM3(4)
+#define STM32_PLLCFG_PLL3N      RCC_PLL3DIVR_N3(48)
+#define STM32_PLLCFG_PLL3P      RCC_PLL3DIVR_P3(2)
+#define STM32_PLLCFG_PLL3Q      RCC_PLL3DIVR_Q3(4)
+#define STM32_PLLCFG_PLL3R      RCC_PLL3DIVR_R3(2)
+
+#define STM32_VCO3_FREQUENCY    ((STM32_HSE_FREQUENCY / 4) * 48)
+#define STM32_PLL3P_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+#define STM32_PLL3Q_FREQUENCY   (STM32_VCO3_FREQUENCY / 4)
+#define STM32_PLL3R_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+
+/* SYSCLK = PLL1P = 480MHz
+ * CPUCLK = SYSCLK / 1 = 480 MHz
+ */
+
+#define STM32_RCC_D1CFGR_D1CPRE  (RCC_D1CFGR_D1CPRE_SYSCLK)
+#define STM32_SYSCLK_FREQUENCY   (STM32_PLL1P_FREQUENCY)
+#define STM32_CPUCLK_FREQUENCY   (STM32_SYSCLK_FREQUENCY / 1)
+
+/* Configure Clock Assignments */
+
+/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max)
+ * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 160
+ */
+
+#define STM32_RCC_D1CFGR_HPRE   RCC_D1CFGR_HPRE_SYSCLKd2        /* HCLK  = SYSCLK / 2 */
+#define STM32_ACLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* ACLK in D1, HCLK3 in D1 */
+#define STM32_HCLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* HCLK in D2, HCLK4 in D3 */
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY            /* same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/2 (80 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE1  RCC_D2CFGR_D2PPRE1_HCLKd2       /* PCLK1 = HCLK / 2 */
+#define STM32_PCLK1_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB2 clock (PCLK2) is HCLK/2 (80 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE2  RCC_D2CFGR_D2PPRE2_HCLKd2       /* PCLK2 = HCLK / 2 */
+#define STM32_PCLK2_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB3 clock (PCLK3) is HCLK/2 (80 MHz) */
+
+#define STM32_RCC_D1CFGR_D1PPRE   RCC_D1CFGR_D1PPRE_HCLKd2        /* PCLK3 = HCLK / 2 */
+#define STM32_PCLK3_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB4 clock (PCLK4) is HCLK/4 (80 MHz) */
+
+#define STM32_RCC_D3CFGR_D3PPRE   RCC_D3CFGR_D3PPRE_HCLKd2       /* PCLK4 = HCLK / 2 */
+#define STM32_PCLK4_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* Timer clock frequencies */
+
+/* Timers driven from APB1 will be twice PCLK1 */
+
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* Timers driven from APB2 will be twice PCLK2 */
+
+#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM15_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM16_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM17_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+
+/* Kernel Clock Configuration
+ *
+ * Note: look at Table 54 in ST Manual
+ */
+
+/* I2C123 clock source */
+
+#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI
+
+/* I2C4 clock source */
+
+#define STM32_RCC_D3CCIPR_I2C4SRC    RCC_D3CCIPR_I2C4SEL_HSI
+
+/* SPI123 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2
+
+/* SPI45 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI45SRC  RCC_D2CCIP1R_SPI45SEL_PLL2
+
+/* SPI6 clock source */
+
+#define STM32_RCC_D3CCIPR_SPI6SRC    RCC_D3CCIPR_SPI6SEL_PLL2
+
+/* USB 1 and 2 clock source */
+
+#define STM32_RCC_D2CCIP2R_USBSRC    RCC_D2CCIP2R_USBSEL_PLL3
+
+/* ADC 1 2 3 clock source */
+
+#define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2
+
+/* FDCAN 1 2 clock source */
+
+#define STM32_RCC_D2CCIP1R_FDCANSEL  RCC_D2CCIP1R_FDCANSEL_HSE   /* FDCAN 1 2 clock source */
+
+#define STM32_FDCANCLK               STM32_HSE_FREQUENCY
+
+/* FLASH wait states
+ *
+ *  ------------ ---------- -----------
+ *  Vcore        MAX ACLK   WAIT STATES
+ *  ------------ ---------- -----------
+ *  1.15-1.26 V     70 MHz    0
+ *  (VOS1 level)   140 MHz    1
+ *                 210 MHz    2
+ *  1.05-1.15 V     55 MHz    0
+ *  (VOS2 level)   110 MHz    1
+ *                 165 MHz    2
+ *                 220 MHz    3
+ *  0.95-1.05 V     45 MHz    0
+ *  (VOS3 level)    90 MHz    1
+ *                 135 MHz    2
+ *                 180 MHz    3
+ *                 225 MHz    4
+ *  ------------ ---------- -----------
+ */
+
+#define BOARD_FLASH_WAITSTATES 2
+
+/* SDMMC definitions ********************************************************/
+
+/* Init 400kHz, freq = PLL1Q/(2*div)  div =  PLL1Q/(2*freq) */
+
+#define STM32_SDMMC_INIT_CLKDIV     (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+
+/* 25 MHz Max for now, 25 mHZ = PLL1Q/(2*div), div =  PLL1Q/(2*freq)
+ * div = 4.8 = 240 / 50, So round up to 5 for default speed 24 MB/s
+ */
+
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_SDXFR_CLKDIV    (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_SDXFR_CLKDIV    (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+
+#define STM32_SDMMC_CLKCR_EDGE      STM32_SDMMC_CLKCR_NEGEDGE
+
+/* LED definitions ******************************************************************/
+/* The ARKV6X board has three, LED_GREEN a Green LED, LED_BLUE a Blue LED and
+ * LED_RED a Red LED, that can be controlled by software.
+ *
+ * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
+ * The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with board_userled() */
+
+/* LED definitions ******************************************************************/
+/* The px4_fmu-v6x board has three, LED_GREEN a Green LED, LED_BLUE a Blue LED and
+ * LED_RED a Red LED, that can be controlled by software.
+ *
+ * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
+ * The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with board_userled() */
+
+#define BOARD_LED1        0
+#define BOARD_LED2        1
+#define BOARD_LED3        2
+#define BOARD_NLEDS       3
+
+#define BOARD_LED_RED     BOARD_LED1
+#define BOARD_LED_GREEN   BOARD_LED2
+#define BOARD_LED_BLUE    BOARD_LED3
+
+/* LED bits for use with board_userled_all() */
+
+#define BOARD_LED1_BIT    (1 << BOARD_LED1)
+#define BOARD_LED2_BIT    (1 << BOARD_LED2)
+#define BOARD_LED3_BIT    (1 << BOARD_LED3)
+
+/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
+ * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
+ * events as follows:
+ *
+ *
+ *   SYMBOL                     Meaning                      LED state
+ *                                                        Red   Green Blue
+ *   ----------------------  --------------------------  ------ ------ ----*/
+
+#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
+#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
+#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
+#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
+#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
+#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
+#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
+#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
+#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */
+
+/* Thus if the Green LED is statically on, NuttX has successfully booted and
+ * is, apparently, running normally.  If the Red LED is flashing at
+ * approximately 2Hz, then a fatal error has been detected and the system
+ * has halted.
+ */
+
+/* Alternate function pin selections ************************************************/
+
+#define GPIO_USART1_RX   GPIO_USART1_RX_3   /* PB7 */
+#define GPIO_USART1_TX   GPIO_USART1_TX_3   /* PB6 */
+
+#define GPIO_USART2_RX   GPIO_USART2_RX_1   /* PA3 */
+#define GPIO_USART2_TX   GPIO_USART2_TX_2   /* PD5 */
+
+#define GPIO_USART3_RX   GPIO_USART3_RX_3   /* PD9   */
+#define GPIO_USART3_TX   GPIO_USART3_TX_3   /* PD8   */
+
+#define GPIO_UART4_RX    GPIO_UART4_RX_6    /* PH14 */
+#define GPIO_UART4_TX    GPIO_UART4_TX_6    /* PH13 */
+
+#define GPIO_UART5_RX    GPIO_UART5_RX_3    /* PD2  */
+#define GPIO_UART5_TX    GPIO_UART5_TX_3    /* PC12 */
+// GPIO_UART5_RTS  No remap                 /* PC8  */
+//#define GPIO_UART5_CTS   (GPIO_ALT|GPIO_AF8|GPIO_PORTC|GPIO_PIN9|GPIO_PULLDOWN)    /* PC9  */
+
+#define GPIO_USART6_RX   GPIO_USART6_RX_1   /* PC7 */
+#define GPIO_USART6_TX   GPIO_USART6_TX_1   /* PC6  */
+
+#define GPIO_UART7_RX    GPIO_UART7_RX_4    /* PF6  */
+#define GPIO_UART7_TX    GPIO_UART7_TX_3    /* PE8  */
+#define GPIO_UART7_RTS   GPIO_UART7_RTS_2   /* PF8  */
+#define GPIO_UART7_CTS   (GPIO_UART7_CTS_1 | GPIO_PULLDOWN)   /* PE10 */
+
+
+/* CAN
+ *
+ * CAN1 is routed to transceiver.
+ */
+#define GPIO_CAN1_RX     GPIO_CAN1_RX_3     /* PD0  */
+#define GPIO_CAN1_TX     GPIO_CAN1_TX_3     /* PD1  */
+
+/* SPI
+ * SPI1 is sensors1
+ * SPI2 is sensors2
+ * SPI3 is sensors3
+ * SPI4 is Not Used
+ * SPI5 is Not Used
+ * SPI6 is EXTERNAL1
+ *
+ */
+
+#define ADJ_SLEW_RATE(p) (((p) & ~GPIO_SPEED_MASK) | (GPIO_SPEED_2MHz))
+
+#define GPIO_SPI1_MISO   GPIO_SPI1_MISO_3               /* PG9  */
+#define GPIO_SPI1_MOSI   GPIO_SPI1_MOSI_2               /* PB5  */
+#define GPIO_SPI1_SCK    ADJ_SLEW_RATE(GPIO_SPI1_SCK_1) /* PA5  */
+
+#define GPIO_SPI6_MISO   GPIO_SPI6_MISO_2               /* PA6  */
+#define GPIO_SPI6_MOSI   GPIO_SPI6_MOSI_1               /* PG14 */
+#define GPIO_SPI6_SCK    ADJ_SLEW_RATE(GPIO_SPI6_SCK_3) /* PB3  */
+
+/* I2C
+ *
+ *   The optional _GPIO configurations allow the I2C driver to manually
+ *   reset the bus to clear stuck slaves.  They match the pin configuration,
+ *   but are normally-high GPIOs.
+ *
+ */
+
+#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2       /* PB8  */
+#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2       /* PB9  */
+
+#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN8)
+#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN9)
+
+#define GPIO_I2C2_SCL GPIO_I2C2_SCL_2       /* PF1 */
+#define GPIO_I2C2_SDA GPIO_I2C2_SDA_2       /* PF0 */
+
+#define GPIO_I2C2_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN1)
+#define GPIO_I2C2_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN0)
+
+#define GPIO_I2C4_SCL GPIO_I2C4_SCL_2       /* PF14 */
+#define GPIO_I2C4_SDA GPIO_I2C4_SDA_2       /* PF15 */
+
+#define GPIO_I2C4_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN14)
+#define GPIO_I2C4_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTF | GPIO_PIN15)
+
+/* SDMMC2
+ *
+ *      VDD 3.3
+ *      GND
+ *      SDMMC2_CK                           PD6
+ *      SDMMC2_CMD                          PD7
+ *      SDMMC2_D0                           PB14
+ *      SDMMC2_D1                           PB15
+ *      SDMMC2_D2                           PG11
+ *      SDMMC2_D3                           PB4
+ */
+
+#define GPIO_SDMMC2_CK   GPIO_SDMMC2_CK_1  /* PD6 */
+#define GPIO_SDMMC2_CMD  GPIO_SDMMC2_CMD_1 /* PD7 */
+//      GPIO_SDMMC2_D0   No Remap          /* PB14 */
+//      GPIO_SDMMC2_D1   No Remap          /* PB15 */
+#define GPIO_SDMMC2_D2   GPIO_SDMMC2_D2_1  /* PG11 */
+//      GPIO_SDMMC2_D3    No Remap         /* PB4 */
+
+/* USB
+ *
+ *      OTG_FS_DM                           PA11
+ *      OTG_FS_DP                           PA12
+ *      VBUS                                PA9
+ */
+
+
+/* Board provides GPIO or other Hardware for signaling to timing analyzer */
+
+#if defined(CONFIG_BOARD_USE_PROBES)
+# include "stm32_gpio.h"
+# define PROBE_N(n) (1<<((n)-1))
+# define PROBE_1    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTI|GPIO_PIN0)   /* PI0 AUX1 */
+# define PROBE_2    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN12)  /* PH12 AUX2 */
+# define PROBE_3    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN11)  /* PH11 AUX3 */
+# define PROBE_4    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN10)  /* PH10 AUX4 */
+# define PROBE_5    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13)  /* PD13 AUX5 */
+# define PROBE_6    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14)  /* PD14 AUX6 */
+# define PROBE_7    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN6)   /* PH6  AUX7 */
+# define PROBE_8    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN9)   /* PH9  AUX8 */
+
+# define PROBE_INIT(mask) \
+	do { \
+		if ((mask)& PROBE_N(1)) { stm32_configgpio(PROBE_1); } \
+		if ((mask)& PROBE_N(2)) { stm32_configgpio(PROBE_2); } \
+		if ((mask)& PROBE_N(3)) { stm32_configgpio(PROBE_3); } \
+		if ((mask)& PROBE_N(4)) { stm32_configgpio(PROBE_4); } \
+		if ((mask)& PROBE_N(5)) { stm32_configgpio(PROBE_5); } \
+		if ((mask)& PROBE_N(6)) { stm32_configgpio(PROBE_6); } \
+		if ((mask)& PROBE_N(7)) { stm32_configgpio(PROBE_7); } \
+		if ((mask)& PROBE_N(8)) { stm32_configgpio(PROBE_8); } \
+		if ((mask)& PROBE_N(9)) { stm32_configgpio(PROBE_9); } \
+	} while(0)
+
+# define PROBE(n,s)  do {stm32_gpiowrite(PROBE_##n,(s));}while(0)
+# define PROBE_MARK(n) PROBE(n,false);PROBE(n,true)
+#else
+# define PROBE_INIT(mask)
+# define PROBE(n,s)
+# define PROBE_MARK(n)
+#endif
+
+#endif  /*__NUTTX_CONFIG_PX4_FMU_V6X_INCLUDE_BOARD_H  */

boards/ark/fpv/nuttx-config/include/board_dma_map.h

@@ -0,0 +1,108 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2024 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+// DMAMUX1 Using at most 8 Channels on DMA1 --------   Assigned
+//                                                     V
+
+// Timer 4 Channel 1                               /* DMA1:29 TIM4CH1 */
+
+#define DMAMAP_SPI1_RX    DMAMAP_DMA12_SPI1RX_0   /* 1 DMA1:37 IIM-42653 */
+#define DMAMAP_SPI1_TX    DMAMAP_DMA12_SPI1TX_0   /* 2 DMA1:38 IIM-42653 */
+
+//#define DMAMAP_SPI2_RX    DMAMAP_DMA12_SPI2RX_0  /* 3 DMA1:39 ICM-42688-P */
+//#define DMAMAP_SPI2_TX    DMAMAP_DMA12_SPI2TX_0  /* 4 DMA1:40 ICM-42688-P */
+
+#define DMAMAP_USART1_RX  DMAMAP_DMA12_USART1RX_0 /*  DMA1:41  GPS1 */
+#define DMAMAP_USART1_TX  DMAMAP_DMA12_USART1TX_0 /*  DMA1:42  GPS1 */
+
+//#define DMAMAP_USART3_RX  DMAMAP_DMA12_USART3RX_0 /*  DMA1:45 DEBUG */
+//#define DMAMAP_USART3_TX  DMAMAP_DMA12_USART3TX_0 /*  DMA1:46 DEBUG */
+
+// Timer 8 Channel 1                               /* DMA1:47 TIM8CH1 */
+// Timer 8 Channel 2                               /* DMA1:48 TIM8CH2 */
+// Timer 8 Channel 3                               /* DMA1:49 TIM8CH3 */
+// Timer 8 Channel 4                               /* DMA1:50 TIM8CH4 */
+
+// Timer 5 Channel 1                               /* DMA1:55 TIM5CH1 */
+// Timer 5 Channel 2                               /* DMA1:56 TIM5CH2 */
+// Timer 5 Channel 3                               /* DMA1:57 TIM5CH3 */
+// Timer 5 Channel 4                               /* DMA1:58 TIM5CH4 */
+
+// #define DMAMAP_UART4_RX   DMAMAP_DMA12_UART4RX_0  /*  DMA1:63 UART4 */
+// #define DMAMAP_UART4_TX   DMAMAP_DMA12_UART4TX_0  /*  DMA1:64 UART4 */
+
+#define DMAMAP_USART6_RX  DMAMAP_DMA12_USART6RX_0 /* 5 DMA1:71 RC */
+// #define DMAMAP_USART6_TX  DMAMAP_DMA12_USART6TX_0 /* 6 DMA1:72 RC */
+
+// Assigned in timer_config.cpp
+
+// Timer 4                                          /* 7 DMA1:32 TIM4UP */
+// Timer 5                                          /* 8 DMA1:50 TIM5UP */
+
+// DMAMUX2 Using at most 8 Channels on DMA2 --------   Assigned
+//                                                     V
+
+// Timer 4 Channel 1                               /* DMA2:29 TIM4CH1 */
+
+#define DMAMAP_USART2_RX  DMAMAP_DMA12_USART2RX_1   /* 3 DMA2:43 TELEM3 */
+#define DMAMAP_USART2_TX  DMAMAP_DMA12_USART2TX_1   /* 4 DMA2:44 TELEM3 */
+
+#define DMAMAP_USART3_RX  DMAMAP_DMA12_USART3RX_1   /* 3 DMA2:45 DEBUG */
+#define DMAMAP_USART3_TX  DMAMAP_DMA12_USART3TX_1   /* 4 DMA2:46 DEBUG */
+
+// Timer 8 Channel 1                                 /* DMA2:47 TIM8CH1 */
+// Timer 8 Channel 2                                 /* DMA2:48 TIM8CH2 */
+// Timer 8 Channel 3                                 /* DMA2:49 TIM8CH3 */
+// Timer 8 Channel 4                                 /* DMA2:50 TIM8CH4 */
+
+// Timer 5 Channel 1                                 /* DMA2:55 TIM5CH1 */
+// Timer 5 Channel 2                                 /* DMA2:56 TIM5CH2 */
+// Timer 5 Channel 3                                 /* DMA2:57 TIM5CH3 */
+// Timer 5 Channel 4                                 /* DMA2:58 TIM5CH4 */
+
+//#define DMAMAP_SPI3_RX    DMAMAP_DMA12_SPI3RX_1     /* 1 DMA2:61 BMI088 */
+//#define DMAMAP_SPI3_TX    DMAMAP_DMA12_SPI3TX_1     /* 2 DMA2:62 BMI088 */
+
+#define DMAMAP_UART5_RX   DMAMAP_DMA12_UART5RX_1    /* 5 DMA2:65 TELEM2 */
+#define DMAMAP_UART5_TX   DMAMAP_DMA12_UART5TX_1    /* 6 DMA2:66 TELEM2 */
+
+#define DMAMAP_UART7_RX   DMAMAP_DMA12_UART7RX_1    /* 7 DMA1:79 TELEM1 */
+#define DMAMAP_UART7_TX   DMAMAP_DMA12_UART7TX_1    /* 8 DMA1:80 TELEM1 */
+
+// DMAMUX2 Using at most 8 Channels on BDMA --------   Assigned
+//                                                     V
+
+#define DMAMAP_SPI6_RX    DMAMAP_BDMA_SPI6_RX       /* 1 BDMA:11 SPI J11 */
+#define DMAMAP_SPI6_TX    DMAMAP_BDMA_SPI6_TX       /* 2 BDMA:12 SPI J11 */

boards/ark/fpv/nuttx-config/nsh/defconfig

@@ -0,0 +1,279 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_MMCSD_HAVE_CARDDETECT is not set
+# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
+# CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_MMCSD_SPI is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_CAT is not set
+# CONFIG_NSH_DISABLE_CD is not set
+# CONFIG_NSH_DISABLE_CP is not set
+# CONFIG_NSH_DISABLE_DATE is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXPORT is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_IFCONFIG is not set
+# CONFIG_NSH_DISABLE_IFUPDOWN is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MKFATFS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PS is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_RM is not set
+# CONFIG_NSH_DISABLE_RMDIR is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_SET is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_TELNETD is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/ark/fpv/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="ark"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743II=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=768
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_DCACHE=y
+CONFIG_ARMV7M_DTCM=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_ARM_MPU_EARLY_RESET=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARD_CRASHDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=95751
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BUILTIN=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x003B
+CONFIG_CDCACM_PRODUCTSTR="ARK FPV.x"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x3185
+CONFIG_CDCACM_VENDORSTR="ARK"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_MEMFAULT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEBUG_TCBINFO=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
+CONFIG_DEV_PIPE_SIZE=70
+CONFIG_EXPERIMENTAL=y
+CONFIG_FAT_DMAMEMORY=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_LFN_ALIAS_HASH=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_BINFS=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FATTIME=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
+CONFIG_FS_PROCFS_MAX_TASKS=64
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3194
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_MAX_EXITFUNS=1
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MMCSD=y
+CONFIG_MMCSD_SDIO=y
+CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y
+CONFIG_MM_REGIONS=4
+CONFIG_MTD=y
+CONFIG_MTD_BYTE_WRITE=y
+CONFIG_MTD_PARTITION=y
+CONFIG_MTD_PROGMEM=y
+CONFIG_MTD_RAMTRON=y
+CONFIG_NAME_MAX=40
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_STRERROR=y
+CONFIG_NSH_VARS=y
+CONFIG_OTG_ID_GPIO_DISABLE=y
+CONFIG_PIPES=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAMTRON_EMULATE_PAGE_SHIFT=5
+CONFIG_RAMTRON_EMULATE_SECTOR_SHIFT=5
+CONFIG_RAMTRON_SETSPEED=y
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_READLINE_CMD_HISTORY=y
+CONFIG_READLINE_TABCOMPLETION=y
+CONFIG_RTC_DATETIME=y
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_LPWORKPRIORITY=50
+CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_WAITPID=y
+CONFIG_SDMMC2_SDIO_PULLUP=y
+CONFIG_SEM_PREALLOCHOLDERS=32
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STM32H7_ADC1=y
+CONFIG_STM32H7_ADC3=y
+CONFIG_STM32H7_BBSRAM=y
+CONFIG_STM32H7_BBSRAM_FILES=5
+CONFIG_STM32H7_BDMA=y
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_DMACAPABLE=y
+CONFIG_STM32H7_FLASH_OVERRIDE_I=y
+CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
+CONFIG_STM32H7_I2C1=y
+CONFIG_STM32H7_I2C2=y
+CONFIG_STM32H7_I2C4=y
+CONFIG_STM32H7_I2C_DYNTIMEO=y
+CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_RTC=y
+CONFIG_STM32H7_RTC_AUTO_LSECLOCK_START_DRV_CAPABILITY=y
+CONFIG_STM32H7_RTC_MAGIC_REG=1
+CONFIG_STM32H7_SAVE_CRASHDUMP=y
+CONFIG_STM32H7_SDMMC2=y
+CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_SPI1=y
+CONFIG_STM32H7_SPI1_DMA=y
+CONFIG_STM32H7_SPI1_DMA_BUFFER=1024
+CONFIG_STM32H7_SPI6=y
+CONFIG_STM32H7_SPI6_DMA=y
+CONFIG_STM32H7_SPI6_DMA_BUFFER=1024
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_TIM2=y
+CONFIG_STM32H7_TIM3=y
+CONFIG_STM32H7_TIM4=y
+CONFIG_STM32H7_TIM5=y
+CONFIG_STM32H7_TIM8=y
+CONFIG_STM32H7_TIM12=y
+CONFIG_STM32H7_UART4=y
+CONFIG_STM32H7_UART5=y
+CONFIG_STM32H7_UART7=y
+CONFIG_STM32H7_USART1=y
+CONFIG_STM32H7_USART2=y
+CONFIG_STM32H7_USART3=y
+CONFIG_STM32H7_USART6=y
+CONFIG_STM32H7_USART_BREAKS=y
+CONFIG_STM32H7_USART_INVERT=y
+CONFIG_STM32H7_USART_SINGLEWIRE=y
+CONFIG_STM32H7_USART_SWAP=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_UART4_BAUD=57600
+CONFIG_UART4_RXBUFSIZE=600
+CONFIG_UART4_TXBUFSIZE=1500
+CONFIG_UART5_IFLOWCONTROL=y
+CONFIG_UART5_OFLOWCONTROL=y
+CONFIG_UART5_RXDMA=y
+CONFIG_UART5_RXBUFSIZE=600
+CONFIG_UART5_TXBUFSIZE=10000
+CONFIG_UART5_TXDMA=y
+CONFIG_UART7_BAUD=57600
+CONFIG_UART7_IFLOWCONTROL=y
+CONFIG_UART7_OFLOWCONTROL=y
+CONFIG_UART7_RXBUFSIZE=600
+CONFIG_UART7_RXDMA=y
+CONFIG_UART7_TXBUFSIZE=3000
+CONFIG_UART7_TXDMA=y
+CONFIG_USART1_BAUD=57600
+CONFIG_USART1_RXDMA=y
+CONFIG_USART1_TXDMA=y
+CONFIG_USART1_RXBUFSIZE=600
+CONFIG_USART1_TXBUFSIZE=1500
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_RXDMA=y
+CONFIG_USART2_TXDMA=y
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_TXBUFSIZE=1500
+CONFIG_USART3_BAUD=57600
+CONFIG_USART3_RXBUFSIZE=180
+CONFIG_USART3_RXDMA=y
+CONFIG_USART3_SERIAL_CONSOLE=y
+CONFIG_USART3_TXBUFSIZE=1500
+CONFIG_USART3_TXDMA=y
+CONFIG_USART6_BAUD=57600
+CONFIG_USART6_RXDMA=y
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_WATCHDOG=y

boards/ark/fpv/nuttx-config/scripts/bootloader_script.ld

@@ -0,0 +1,215 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2024 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The ARKV6X uses an STM32H743II has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743II, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The ARKV6X has a test point on board, the BOOT0 pin is at ground so by
+ * default, the STM32 will boot to address 0x0800:0000 in FLASH unless the test
+ * point is pulled to 3.3V.then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743II also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ *
+ * The bootloader uses the first sector of the flash, which is 128K in length.
+ */
+
+MEMORY
+{
+	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	flash (rx)  : ORIGIN = 0x08000000, LENGTH =  128K
+	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
+	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
+	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
+	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
+	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
+	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/ark/fpv/nuttx-config/scripts/script.ld

@@ -0,0 +1,229 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2024 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The ARKV6X uses an STM32H743II has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743II, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The ARKV6X has a test point on board, the BOOT0 pin is at ground so by
+ * default, the STM32 will boot to address 0x0800:0000 in FLASH unless the test
+ * point is pulled to 3.3V.then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743II also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	ITCM_RAM  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	FLASH      (rx) : ORIGIN = 0x08020000, LENGTH = 1792K /* params in last sector */
+
+	DTCM1_RAM (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	DTCM2_RAM (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	AXI_SRAM  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K /* D1 domain AXI bus */
+	SRAM1     (rwx) : ORIGIN = 0x30000000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM2     (rwx) : ORIGIN = 0x30020000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM3     (rwx) : ORIGIN = 0x30040000, LENGTH =   32K /* D2 domain AHB bus */
+	SRAM4     (rwx) : ORIGIN = 0x38000000, LENGTH =   64K /* D3 domain */
+	BKPRAM    (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+EXTERN(board_get_manifest)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > FLASH
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > FLASH
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > FLASH
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > FLASH
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+
+		/* Pad out last section as the STM32H7 Flash write size is 256 bits. 32 bytes */
+		. = ALIGN(16);
+		FILL(0xffff)
+		. += 16;
+	} > AXI_SRAM AT > FLASH  = 0xffff
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > AXI_SRAM
+
+	/* Emit the the D3 power domain section for locating BDMA data */
+
+	.sram4_reserve (NOLOAD) :
+	{
+		*(.sram4)
+		. = ALIGN(4);
+		_sram4_heap_start = ABSOLUTE(.);
+	} > SRAM4
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/ark/fpv/src/CMakeLists.txt

@@ -0,0 +1,77 @@
+############################################################################
+#
+#   Copyright (c) 2016 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+if("${PX4_BOARD_LABEL}" STREQUAL  "bootloader")
+	add_compile_definitions(BOOTLOADER)
+	add_library(drivers_board
+		bootloader_main.c
+		init.c
+		usb.c
+		timer_config.cpp
+	)
+	target_link_libraries(drivers_board
+		PRIVATE
+			nuttx_arch # sdio
+			nuttx_drivers # sdio
+			px4_layer #gpio
+			arch_io_pins # iotimer
+			bootloader
+	)
+	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common)
+
+else()
+	add_library(drivers_board
+		can.c
+		i2c.cpp
+		init.c
+		led.c
+		mtd.cpp
+		sdio.c
+		spi.cpp
+		spix_sync.c
+		spix_sync.h
+		timer_config.cpp
+		usb.c
+	)
+	add_dependencies(drivers_board arch_board_hw_info)
+
+	target_link_libraries(drivers_board
+		PRIVATE
+			arch_io_pins
+			arch_spi
+			arch_board_hw_info
+			drivers__led # drv_led_start
+			nuttx_arch # sdio
+			nuttx_drivers # sdio
+			px4_layer
+	)
+endif()

boards/ark/fpv/src/board_config.h

@@ -0,0 +1,397 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2016-2024 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * ARK FPV internal definitions
+ */
+
+#pragma once
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+
+#include <stm32_gpio.h>
+
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+
+#undef TRACE_PINS
+
+/* Configuration ************************************************************************************/
+
+#  define BOARD_HAS_USB_VALID           1
+#  define BOARD_HAS_NBAT_V              1
+#  define BOARD_HAS_NBAT_I              1
+
+/* PX4FMU GPIOs ***********************************************************************************/
+
+/* Trace Clock and D0-D3 are available on the trace connector
+ *
+ * TRACECLK PE2  - Dedicated       - Trace Connector Pin 1
+ * TRACED0  PE3  - nLED_RED        - Trace Connector Pin 3
+ * TRACED1  PE4  - nLED_GREEN      - Trace Connector Pin 5
+ * TRACED2  PE5  - nLED_BLUE       - Trace Connector Pin 7
+ * TRACED3  PE6  - nARMED          - Trace Connector Pin 8
+
+ */
+
+/* LEDs are driven with push open drain to support Anode to 5V or 3.3V or used as TRACE0-2 */
+
+#if !defined(TRACE_PINS)
+#  define GPIO_nLED_RED        /* PE3 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
+#  define GPIO_nLED_GREEN      /* PE4 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
+#  define GPIO_nLED_BLUE       /* PE5 */  (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN5)
+
+#  define BOARD_HAS_CONTROL_STATUS_LEDS      1
+#  define BOARD_OVERLOAD_LED     LED_RED
+#  define BOARD_ARMED_STATE_LED  LED_BLUE
+
+#else
+
+#  define GPIO_TRACECLK1 (GPIO_TRACECLK |GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN2)
+#  define GPIO_TRACED0   (GPIO_TRACED0_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN3)
+#  define GPIO_TRACED1   (GPIO_TRACED1_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN4)
+#  define GPIO_TRACED2   (GPIO_TRACED2_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN5)
+#  define GPIO_TRACED3   (GPIO_TRACED3_2|GPIO_PULLUP|GPIO_SPEED_100MHz|GPIO_PUSHPULL)  //(GPIO_ALT|GPIO_AF0|GPIO_PORTE|GPIO_PIN6)
+//#define GPIO_TRACESWO                        //(GPIO_ALT|GPIO_AF0|GPIO_PORTB|GPIO_PIN3)
+
+#  undef  BOARD_HAS_CONTROL_STATUS_LEDS
+#  undef  BOARD_OVERLOAD_LED
+#  undef  BOARD_ARMED_STATE_LED
+
+#  define GPIO_nLED_RED    GPIO_TRACED0
+#  define GPIO_nLED_GREEN  GPIO_TRACED1
+#  define GPIO_nLED_BLUE   GPIO_TRACED2
+#  define GPIO_nARMED      GPIO_TRACED3
+#  define GPIO_nARMED_INIT GPIO_TRACED3
+#endif
+
+/* SPI */
+
+#define SPI6_nRESET_EXTERNAL1       /* PF10 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTF|GPIO_PIN10)
+#define SPI6_RESET(on_true)          px4_arch_gpiowrite(SPI6_nRESET_EXTERNAL1, !(on_true))
+
+/* I2C busses */
+
+/* Devices on the onboard buses.
+ *
+ * Note that these are unshifted addresses.
+ */
+#define PX4_I2C_OBDEV_SE050         0x48
+
+/*
+ * ADC channels
+ *
+ * These are the channel numbers of the ADCs of the microcontroller that
+ * can be used by the Px4 Firmware in the adc driver
+ */
+
+/* ADC defines to be used in sensors.cpp to read from a particular channel */
+
+#define ADC1_CH(n)                  (n)
+
+/* N.B. there is no offset mapping needed for ADC3 because */
+#define ADC3_CH(n)                  (n)
+
+/* We are only use ADC3 for REV/VER.
+ * ADC3_6V6 and ADC3_3V3 are mapped back to ADC1
+ * To do this We are relying on PC2_C, PC3_C being connected to PC2, PC3
+ * respectively by the SYSCFG_PMCR default of setting for PC3SO PC2SO PA1SO
+ * PA0SO of 0.
+ *
+ *  0 Analog switch closed (pads are connected through the analog switch)
+ *
+ * So ADC3_INP0 is GPIO_ADC123_INP12
+ *    ADC3_INP1 is GPIO_ADC12_INP13
+ */
+
+/* Define GPIO pins used as ADC N.B. Channel numbers must match below  */
+
+#define PX4_ADC_GPIO  \
+	/* PA0  */  GPIO_ADC1_INP16,   \
+	/* PA4  */  GPIO_ADC12_INP18,  \
+	/* PB0  */  GPIO_ADC12_INP9,   \
+	/* PB1  */  GPIO_ADC12_INP5,   \
+	/* PC2  */  GPIO_ADC123_INP12, \
+	/* PC3  */  GPIO_ADC12_INP13,  \
+	/* PF12 */  GPIO_ADC1_INP6,    \
+	/* PH3  */  GPIO_ADC3_INP14,   \
+	/* PH4  */  GPIO_ADC3_INP15
+
+/* Define Channel numbers must match above GPIO pin IN(n)*/
+#define ADC_BATTERY_VOLTAGE_CHANNEL        	/* PB0 */  ADC1_CH(9)
+#define ADC_BATTERY_CURRENT_CHANNEL        	/* PC2 */  ADC3_CH(12)
+#define ADC_SCALED_12V_CHANNEL	     		/* PA4 */  ADC1_CH(18)
+#define ADC_SCALED_VDD_3V3_SENSORS_CHANNEL     /* PA0 */  ADC1_CH(16)
+#define ADC_SCALED_V5_CHANNEL                   /* PB1 */  ADC1_CH(5)
+#define ADC_HW_VER_SENSE_CHANNEL                /* PH3 */  ADC3_CH(14)
+#define ADC_HW_REV_SENSE_CHANNEL                /* PH4 */  ADC3_CH(15)
+
+#define ADC_CHANNELS \
+	((1 << ADC_BATTERY_VOLTAGE_CHANNEL)         | \
+	 (1 << ADC_BATTERY_CURRENT_CHANNEL)         | \
+	 (1 << ADC_SCALED_VDD_3V3_SENSORS_CHANNEL)  | \
+	 (1 << ADC_SCALED_V5_CHANNEL)               | \
+	 (1 << ADC_SCALED_12V_CHANNEL))
+
+
+#define BOARD_BATTERY1_V_DIV	 (21.0f) // (20k + 1k) / 1k = 21
+
+#define ADC_SCALED_PAYLOAD_SENSE ADC_SCALED_12V_CHANNEL
+
+/* HW has to large of R termination on ADC todo:change when HW value is chosen */
+
+#define HW_REV_VER_ADC_BASE STM32_ADC3_BASE
+
+#define SYSTEM_ADC_BASE STM32_ADC1_BASE
+
+/* HW has to large of R termination on ADC todo:change when HW value is chosen */
+#define BOARD_ADC_OPEN_CIRCUIT_V     (5.6f)
+
+/* HW Version and Revision drive signals Default to 1 to detect */
+#define BOARD_HAS_HW_SPLIT_VERSIONING
+
+#define GPIO_HW_VER_REV_DRIVE  /* PG0 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTG|GPIO_PIN0)
+#define GPIO_HW_REV_SENSE      /* PH4 */  GPIO_ADC3_INP15
+#define GPIO_HW_VER_SENSE      /* PH3 */  GPIO_ADC3_INP14
+#define HW_INFO_INIT_PREFIX    "ARKFPV"
+
+#define BOARD_NUM_SPI_CFG_HW_VERSIONS 2
+//                 Base/FMUM
+#define ARKFPV_0   HW_FMUM_ID(0x0) // ARKFPV,     Sensor Set  Rev 0
+#define ARKFPV_1   HW_FMUM_ID(0x1) // ARKFPV,     Sensor Set  Rev 1
+
+#define UAVCAN_NUM_IFACES_RUNTIME  1
+
+/* HEATER
+ * PWM in future
+ */
+#define GPIO_HEATER_OUTPUT   /* PB10  T2CH3 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10)
+#define HEATER_OUTPUT_EN(on_true)	       px4_arch_gpiowrite(GPIO_HEATER_OUTPUT, (on_true))
+
+/* PE6 is nARMED
+ *  The GPIO will be set as input while not armed HW will have external HW Pull UP.
+ *  While armed it shall be configured at a GPIO OUT set LOW
+ */
+#if !defined(TRACE_PINS)
+#define GPIO_nARMED_INIT     /* PE6 */  (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN6)
+#define GPIO_nARMED          /* PE6 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN6)
+#define BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE(enabled)  px4_arch_configgpio((enabled) ? GPIO_nARMED : GPIO_nARMED_INIT)
+#define BOARD_GET_EXTERNAL_LOCKOUT_STATE() px4_arch_gpioread(GPIO_nARMED)
+#endif
+
+/* PWM
+ */
+#define DIRECT_PWM_OUTPUT_CHANNELS   9
+
+#define GPIO_FMU_CH1                    /* PI0  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN0)
+#define GPIO_FMU_CH2                    /* PH12 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN12)
+#define GPIO_FMU_CH3                    /* PH11 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN11)
+#define GPIO_FMU_CH4                    /* PH10 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTH|GPIO_PIN10)
+#define GPIO_FMU_CH5                    /* PI5  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN5)
+#define GPIO_FMU_CH6                    /* PI6  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN6)
+#define GPIO_FMU_CH7                    /* PI7  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN7)
+#define GPIO_FMU_CH8                    /* PI2  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTI|GPIO_PIN2)
+#define GPIO_FMU_CH9                    /* PD12 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTD|GPIO_PIN12)
+
+#define GPIO_SPIX_SYNC                  /* PE9  */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTE|GPIO_PIN9)
+
+/* Power supply control and monitoring GPIOs */
+
+#define GPIO_VDD_5V_PGOOD         	/* PF13 */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTF|GPIO_PIN13)
+#define GPIO_VDD_12V_PGOOD	 	/* PE15 */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTE|GPIO_PIN15)
+#define GPIO_5V_ON_BATTERY	 	/* PG1  */ (GPIO_INPUT |GPIO_FLOAT|GPIO_PORTG|GPIO_PIN1)
+#define GPIO_VDD_12V_EN			/* PG4  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTG|GPIO_PIN4)
+
+#define GPIO_VDD_3V3_SD_CARD_EN         /* PC13 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13)
+
+
+#define BOARD_NUMBER_BRICKS             1
+
+/* Define True logic Power Control in arch agnostic form */
+
+#define VDD_3V3_SD_CARD_EN(on_true)        px4_arch_gpiowrite(GPIO_VDD_3V3_SD_CARD_EN, (on_true))
+#define PAYLOAD_POWER_EN(on_true)          px4_arch_gpiowrite(GPIO_VDD_12V_EN, (on_true))
+
+/* USB OTG FS
+ *
+ * PA9  OTG_FS_VBUS VBUS sensing
+ */
+#define GPIO_OTGFS_VBUS         /* PA9 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTA|GPIO_PIN9)
+
+#define FLASH_BASED_PARAMS
+
+/* High-resolution timer */
+#define HRT_TIMER               3  /* use timer3 for the HRT */
+#define HRT_TIMER_CHANNEL       1 /* use capture/compare channel 1 */
+
+/* RC Serial port */
+
+#define RC_SERIAL_PORT                     "/dev/ttyS4"
+
+/* PWM input driver. Use FMU AUX5 pins attached to timer4 channel 2 */
+#define PWMIN_TIMER                       4
+#define PWMIN_TIMER_CHANNEL    /* T4C2 */ 2
+#define GPIO_PWM_IN            /* PD13 */ GPIO_TIM4_CH2IN_2
+
+#define SDIO_SLOTNO                    0  /* Only one slot */
+#define SDIO_MINOR                     0
+
+/* SD card bringup does not work if performed on the IDLE thread because it
+ * will cause waiting.  Use either:
+ *
+ *  CONFIG_BOARDCTL=y, OR
+ *  CONFIG_BOARD_INITIALIZE=y && CONFIG_BOARD_INITTHREAD=y
+ */
+
+#if defined(CONFIG_BOARD_INITIALIZE) && !defined(CONFIG_BOARDCTL) && \
+   !defined(CONFIG_BOARD_INITTHREAD)
+#  warning SDIO initialization cannot be perfomed on the IDLE thread
+#endif
+
+/* By Providing BOARD_ADC_USB_CONNECTED (using the px4_arch abstraction)
+ * this board support the ADC system_power interface, and therefore
+ * provides the true logic GPIO BOARD_ADC_xxxx macros.
+ */
+#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS))
+
+/* ARKFPV never powers off the Servo rail */
+
+#define BOARD_ADC_SERVO_VALID     (1)
+
+#define BOARD_ADC_BRICK_VALID   (px4_arch_gpioread(GPIO_VDD_5V_PGOOD))
+#define BOARD_GPIO_PAYOLOAD_V_VALID (px4_arch_gpioread(GPIO_VDD_12V_PGOOD))
+
+/* This board provides a DMA pool and APIs */
+#define BOARD_DMA_ALLOC_POOL_SIZE 5120
+
+/* This board provides the board_on_reset interface */
+
+#define BOARD_HAS_ON_RESET 1
+
+#if defined(TRACE_PINS)
+#define GPIO_TRACE                          \
+	GPIO_TRACECLK1,                           \
+	GPIO_TRACED0,                             \
+	GPIO_TRACED1,                             \
+	GPIO_TRACED2,                             \
+	GPIO_TRACED3
+#else
+#define GPIO_TRACE (GPIO_OUTPUT|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN2)
+#endif
+
+#define PX4_GPIO_INIT_LIST { \
+		GPIO_TRACE,                       \
+		PX4_ADC_GPIO,                     \
+		GPIO_HW_VER_REV_DRIVE,            \
+		GPIO_CAN1_TX,                     \
+		GPIO_CAN1_RX,                     \
+		GPIO_HEATER_OUTPUT,               \
+		GPIO_VDD_5V_PGOOD,                \
+		GPIO_VDD_12V_PGOOD,               \
+		GPIO_VDD_12V_EN,                  \
+		GPIO_5V_ON_BATTERY,               \
+		GPIO_VDD_3V3_SD_CARD_EN,          \
+		GPIO_nARMED_INIT,                 \
+		SPI6_nRESET_EXTERNAL1,            \
+		GPIO_FMU_CH1,     	          \
+		GPIO_FMU_CH2,     	          \
+		GPIO_FMU_CH3,     	          \
+		GPIO_FMU_CH4,     	          \
+		GPIO_FMU_CH5,     	          \
+		GPIO_FMU_CH6,     	          \
+		GPIO_FMU_CH7,     	          \
+		GPIO_FMU_CH8,     	          \
+		GPIO_FMU_CH9,     	          \
+		GPIO_SPIX_SYNC                    \
+	}
+
+#define BOARD_ENABLE_CONSOLE_BUFFER
+
+#define BOARD_NUM_IO_TIMERS  3
+#define BOARD_SPIX_SYNC_FREQ 32000
+
+__BEGIN_DECLS
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void);
+
+/****************************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the PX4FMU board.
+ *
+ ****************************************************************************************************/
+
+extern void stm32_spiinitialize(void);
+
+extern void stm32_usbinitialize(void);
+
+extern void board_peripheral_reset(int ms);
+
+#include <px4_platform_common/board_common.h>
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS

boards/ark/fpv/src/bootloader_main.c

@@ -0,0 +1,85 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2022 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file bootloader_main.c
+ *
+ * FMU-specific early startup code for bootloader
+*/
+
+#include "board_config.h"
+#include "bl.h"
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+#include <px4_platform/gpio.h>
+#include <px4_platform_common/init.h>
+
+extern int sercon_main(int c, char **argv);
+
+__EXPORT void board_on_reset(int status) {}
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* configure pins */
+	const uint32_t list[] = PX4_GPIO_INIT_LIST;
+
+	for (size_t gpio = 0; gpio < arraySize(list); gpio++) {
+		if (list[gpio] != 0) {
+			px4_arch_configgpio(list[gpio]);
+		}
+	}
+
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+}
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	return 0;
+}
+
+void board_late_initialize(void)
+{
+	sercon_main(0, NULL);
+}
+
+extern void sys_tick_handler(void);
+void board_timerhook(void)
+{
+	sys_tick_handler();
+}

boards/ark/fpv/src/can.c

@@ -0,0 +1,140 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file can.c
+ *
+ * Board-specific CAN functions.
+ */
+
+#if !defined(CONFIG_CAN)
+
+#include <stdint.h>
+
+#include "board_config.h"
+
+
+__EXPORT
+uint16_t board_get_can_interfaces(void)
+{
+	uint16_t enabled_interfaces = 0x3;
+
+	enabled_interfaces &= ~(1 << 1);
+
+	return enabled_interfaces;
+}
+
+#else
+
+#include <errno.h>
+#include <debug.h>
+
+#include <nuttx/can/can.h>
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "arm_internal.h"
+
+#include "chip.h"
+#include "stm32_can.h"
+#include "board_config.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+/* Configuration ********************************************************************/
+
+#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2)
+#  warning "Both CAN1 and CAN2 are enabled.  Assuming only CAN1."
+#  undef CONFIG_STM32_CAN2
+#endif
+
+#ifdef CONFIG_STM32_CAN1
+#  define CAN_PORT 1
+#else
+#  define CAN_PORT 2
+#endif
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+int can_devinit(void);
+
+/************************************************************************************
+ * Name: can_devinit
+ *
+ * Description:
+ *   All STM32 architectures must provide the following interface to work with
+ *   examples/can.
+ *
+ ************************************************************************************/
+
+int can_devinit(void)
+{
+	static bool initialized = false;
+	struct can_dev_s *can;
+	int ret;
+
+	/* Check if we have already initialized */
+
+	if (!initialized) {
+		/* Call stm32_caninitialize() to get an instance of the CAN interface */
+
+		can = stm32_caninitialize(CAN_PORT);
+
+		if (can == NULL) {
+			canerr("ERROR:  Failed to get CAN interface\n");
+			return -ENODEV;
+		}
+
+		/* Register the CAN driver at "/dev/can0" */
+
+		ret = can_register("/dev/can0", can);
+
+		if (ret < 0) {
+			canerr("ERROR: can_register failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Now we are initialized */
+
+		initialized = true;
+	}
+
+	return OK;
+}
+#endif /* CONFIG_CAN */

boards/ark/fpv/src/hw_config.h

@@ -0,0 +1,129 @@
+/*
+ * hw_config.h
+ *
+ *  Created on: May 17, 2015
+ *      Author: david_s5
+ */
+
+#ifndef HW_CONFIG_H_
+#define HW_CONFIG_H_
+
+/****************************************************************************
+ * 10-8--2016:
+ *  To simplify the ripple effect on the tools, we will be using
+ *  /dev/serial/by-id/<asterisk>PX4<asterisk> to locate PX4 devices. Therefore
+ *  moving forward all Bootloaders must contain the prefix "PX4 BL "
+ *  in the USBDEVICESTRING
+ *  This Change will be made in an upcoming BL release
+ ****************************************************************************/
+/*
+ * Define usage to configure a bootloader
+ *
+ *
+ * Constant                example          Usage
+ * APP_LOAD_ADDRESS     0x08004000            - The address in Linker Script, where the app fw is org-ed
+ * BOOTLOADER_DELAY     5000                  - Ms to wait while under USB pwr or bootloader request
+ * BOARD_FMUV2
+ * INTERFACE_USB        1                     - (Optional) Scan and use the USB interface for bootloading
+ * INTERFACE_USART      1                     - (Optional) Scan and use the Serial interface for bootloading
+ * USBDEVICESTRING      "PX4 BL FMU v2.x"     - USB id string
+ * USBPRODUCTID         0x0011                - PID Should match defconfig
+ * BOOT_DELAY_ADDRESS   0x000001a0            - (Optional) From the linker script from Linker Script to get a custom
+ *                                               delay provided by an APP FW
+ * BOARD_TYPE           9                     - Must match .prototype boad_id
+ * _FLASH_KBYTES        (*(uint16_t *)0x1fff7a22) - Run time flash size detection
+ * BOARD_FLASH_SECTORS  ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector
+ * BOARD_FLASH_SECTORS   11                   - Hard coded zero based last sector
+ * BOARD_FLASH_SIZE     (_FLASH_KBYTES*1024)-   Total Flash size of device, determined at run time.
+ *                         (1024 * 1024)      - Hard coded Total Flash of device - The bootloader and app reserved will be deducted
+ *                                              programmatically
+ *
+ * BOARD_FIRST_FLASH_SECTOR_TO_ERASE  2        - Optional sectors index in the flash_sectors table  (F4 only), to begin erasing.
+ *                                               This is to allow sectors to be reserved for app fw usage. That will NOT be erased
+ *                                               during a FW upgrade.
+ *                                               The default is 0, and selects the first sector to be erased, as the 0th entry in the
+ *                                               flash_sectors table. Which is the second physical sector of FLASH in the device.
+ *                                               The first physical sector of FLASH is used by the bootloader, and is not defined
+ *                                               in the table.
+ *
+ * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus
+ *                                                                        BOOTLOADER_RESERVATION_SIZE  will be deducted from
+ *                                                                        BOARD_FLASH_SIZE to determine the size of the App FW
+ *                                                                        and hence the address space of FLASH to erase and program.
+ * USBMFGSTRING            "PX4 AP"            - Optional USB MFG string (default is '3D Robotics' if not defined.)
+ * SERIAL_BREAK_DETECT_DISABLED                -  Optional prevent break selection on Serial port from entering or staying in BL
+ *
+ * * Other defines are somewhat self explanatory.
+ */
+
+/* Boot device selection list*/
+#define USB0_DEV       0x01
+#define SERIAL0_DEV    0x02
+#define SERIAL1_DEV    0x04
+
+#define APP_LOAD_ADDRESS               0x08020000
+#define BOOTLOADER_DELAY               5000
+#define INTERFACE_USB                  1
+#define INTERFACE_USB_CONFIG           "/dev/ttyACM0"
+#define BOARD_VBUS                     MK_GPIO_INPUT(GPIO_OTGFS_VBUS)
+
+//#define USE_VBUS_PULL_DOWN
+#define INTERFACE_USART                1
+#define INTERFACE_USART_CONFIG         "/dev/ttyS6,921600"
+#define BOOT_DELAY_ADDRESS             0x000001a0
+#define BOARD_TYPE                     59
+#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
+#define BOARD_FLASH_SECTORS            (14)
+#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)
+#define APP_RESERVATION_SIZE           (1 * 128 * 1024)
+
+#define OSC_FREQ                       16
+
+#define BOARD_PIN_LED_ACTIVITY         GPIO_nLED_BLUE // BLUE
+#define BOARD_PIN_LED_BOOTLOADER       GPIO_nLED_GREEN // GREEN
+#define BOARD_LED_ON                   0
+#define BOARD_LED_OFF                  1
+
+#define SERIAL_BREAK_DETECT_DISABLED   1
+
+/*
+ * Uncommenting this allows to force the bootloader through
+ * a PWM output pin. As this can accidentally initialize
+ * an ESC prematurely, it is not recommended. This feature
+ * has not been used and hence defaults now to off.
+ *
+ * # define BOARD_FORCE_BL_PIN_OUT         (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN14)
+ * # define BOARD_FORCE_BL_PIN_IN          (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN11)
+ *
+ * # define BOARD_POWER_PIN_OUT           (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
+ * # define BOARD_POWER_ON                 1
+ * # define BOARD_POWER_OFF                0
+ * # undef  BOARD_POWER_PIN_RELEASE        // Leave pin enabling Power - un comment to release (disable power)
+ *
+*/
+
+#if !defined(ARCH_SN_MAX_LENGTH)
+# define ARCH_SN_MAX_LENGTH 12
+#endif
+
+#if !defined(APP_RESERVATION_SIZE)
+#  define APP_RESERVATION_SIZE 0
+#endif
+
+#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE)
+#  define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1
+#endif
+
+#if !defined(USB_DATA_ALIGN)
+# define USB_DATA_ALIGN
+#endif
+
+#ifndef BOOT_DEVICES_SELECTION
+#  define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#ifndef BOOT_DEVICES_FILTER_ONUSB
+#  define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#endif /* HW_CONFIG_H_ */

boards/ark/fpv/src/i2c.cpp

@@ -0,0 +1,40 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2022 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/i2c_hw_description.h>
+
+constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
+	initI2CBusExternal(1),
+	initI2CBusInternal(2),
+	initI2CBusInternal(4),
+};

boards/ark/fpv/src/init.c

@@ -0,0 +1,299 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2012-2022 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file init.c
+ *
+ * ARKFMU-specific early startup code.  This file implements the
+ * board_app_initialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialization.
+ */
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include "board_config.h"
+#include "spix_sync.h"
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <string.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <nuttx/spi/spi.h>
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+#include <nuttx/analog/adc.h>
+#include <nuttx/mm/gran.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_board_led.h>
+#include <systemlib/px4_macros.h>
+#include <px4_arch/io_timer.h>
+#include <px4_platform_common/init.h>
+#include <px4_platform_common/px4_manifest.h>
+#include <px4_platform/gpio.h>
+#include <px4_platform/board_determine_hw_info.h>
+#include <px4_platform/board_dma_alloc.h>
+
+# if defined(FLASH_BASED_PARAMS)
+#  include <parameters/flashparams/flashfs.h>
+#endif
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+__END_DECLS
+
+
+/************************************************************************************
+ * Name: board_peripheral_reset
+ *
+ * Description:
+ *
+ ************************************************************************************/
+__EXPORT void board_peripheral_reset(int ms)
+{
+	/* set the peripheral rails off */
+
+	PAYLOAD_POWER_EN(false);
+	board_control_spi_sensors_power(false, 0xffff);
+	SPI6_RESET(true);
+
+	/* wait for the peripheral rail to reach GND */
+	usleep(ms * 1000);
+	syslog(LOG_DEBUG, "reset done, %d ms\n", ms);
+
+	/* re-enable power */
+
+	/* switch the peripheral rail back on */
+	board_control_spi_sensors_power(true, 0xffff);
+	PAYLOAD_POWER_EN(true);
+
+	/* Release SPI6 Reset */
+	SPI6_RESET(false);
+}
+
+/************************************************************************************
+ * Name: board_on_reset
+ *
+ * Description:
+ * Optionally provided function called on entry to board_system_reset
+ * It should perform any house keeping prior to the rest.
+ *
+ * status - 1 if resetting to boot loader
+ *          0 if just resetting
+ *
+ ************************************************************************************/
+__EXPORT void board_on_reset(int status)
+{
+	for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) {
+		px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i)));
+	}
+
+	if (status >= 0) {
+		up_mdelay(6);
+	}
+}
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+__EXPORT void
+stm32_boardinitialize(void)
+{
+	board_on_reset(-1); /* Reset PWM first thing */
+
+	/* configure LEDs */
+
+	board_autoled_initialize();
+
+	/* configure pins */
+
+	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
+	px4_gpio_init(gpio, arraySize(gpio));
+
+	/* configure USB interfaces */
+
+	stm32_usbinitialize();
+
+}
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX; the meaning of the argument is a contract
+ *         between the board-specific initalization logic and the the
+ *         matching application logic.  The value cold be such things as a
+ *         mode enumeration value, a set of DIP switch switch settings, a
+ *         pointer to configuration data read from a file or serial FLASH,
+ *         or whatever you would like to do with it.  Every implementation
+ *         should accept zero/NULL as a default configuration.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	/* Power on Interfaces */
+	PAYLOAD_POWER_EN(true);
+
+	SPI6_RESET(false);
+
+	/* Need hrt running before using the ADC */
+
+	px4_platform_init();
+
+	// Use the default HW_VER_REV(0x0,0x0) for Ramtron
+
+	stm32_spiinitialize();
+
+#if defined(FLASH_BASED_PARAMS)
+	static sector_descriptor_t params_sector_map[] = {
+		{15, 128 * 1024, 0x081E0000},
+		{0, 0, 0},
+	};
+
+	/* Initialize the flashfs layer to use heap allocated memory */
+	int result = parameter_flashfs_init(params_sector_map, NULL, 0);
+
+	if (result != OK) {
+		syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
+		led_on(LED_AMBER);
+	}
+
+#endif // FLASH_BASED_PARAMS
+
+	/* Configure the HW based on the manifest */
+
+	px4_platform_configure();
+
+	if (OK == board_determine_hw_info()) {
+		syslog(LOG_INFO, "[boot] Rev 0x%1x : Ver 0x%1x %s\n", board_get_hw_revision(), board_get_hw_version(),
+		       board_get_hw_type_name());
+
+	} else {
+		syslog(LOG_ERR, "[boot] Failed to read HW revision and version\n");
+	}
+
+	/* Configure the Actual SPI interfaces (after we determined the HW version)  */
+
+	stm32_spiinitialize();
+
+	board_spi_reset(10, 0xffff);
+
+	/* Configure the DMA allocator */
+
+	if (board_dma_alloc_init() < 0) {
+		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
+	}
+
+#if defined(SERIAL_HAVE_RXDMA)
+	// set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event.
+	static struct hrt_call serial_dma_call;
+	hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
+#endif
+
+	/* initial LED state */
+	drv_led_start();
+	led_off(LED_RED);
+	led_on(LED_GREEN); // Indicate Power.
+	led_off(LED_BLUE);
+
+	if (board_hardfault_init(2, true) != 0) {
+		led_on(LED_RED);
+	}
+
+	// Ensure Power is off for > 10 mS
+	usleep(15 * 1000);
+	VDD_3V3_SD_CARD_EN(true);
+	usleep(500 * 1000);
+
+#ifdef CONFIG_MMCSD
+	int ret = stm32_sdio_initialize();
+
+	if (ret != OK) {
+		led_on(LED_RED);
+		return ret;
+	}
+
+#endif /* CONFIG_MMCSD */
+
+	/* Configure the SPIX_SYNC output */
+	spix_sync_servo_init(BOARD_SPIX_SYNC_FREQ);
+	spix_sync_servo_set(0, 150);
+
+	return OK;
+}

boards/ark/fpv/src/led.c

@@ -0,0 +1,234 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2013 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file led.c
+ *
+ * ARKFMU LED backend.
+ */
+
+#include <px4_platform_common/px4_config.h>
+
+#include <stdbool.h>
+
+#include "chip.h"
+#include "stm32_gpio.h"
+#include "board_config.h"
+
+#include <nuttx/board.h>
+#include <arch/board/board.h>
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+extern void led_toggle(int led);
+__END_DECLS
+
+#ifdef CONFIG_ARCH_LEDS
+static bool nuttx_owns_leds = true;
+//                                B  R  S  G
+//                                0  1  2  3
+static const uint8_t xlatpx4[] = {1, 2, 4, 0};
+#  define xlat(p) xlatpx4[(p)]
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_GREEN,   // Indexed by BOARD_LED_GREEN
+	GPIO_nLED_BLUE,    // Indexed by BOARD_LED_BLUE
+	GPIO_nLED_RED,     // Indexed by BOARD_LED_RED
+};
+
+#else
+
+#  define xlat(p) (p)
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_BLUE,                     // Indexed by LED_BLUE
+	GPIO_nLED_RED,                      // Indexed by LED_RED, LED_AMBER
+	0,                                  // Indexed by LED_SAFETY (defaulted to an input)
+	GPIO_nLED_GREEN,                    // Indexed by LED_GREEN
+};
+
+#endif
+
+__EXPORT void led_init(void)
+{
+	for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
+		if (g_ledmap[l] != 0) {
+			stm32_configgpio(g_ledmap[l]);
+		}
+	}
+}
+
+static void phy_set_led(int led, bool state)
+{
+	/* Drive Low to switch on */
+
+	if (g_ledmap[led] != 0) {
+		stm32_gpiowrite(g_ledmap[led], !state);
+	}
+}
+
+static bool phy_get_led(int led)
+{
+	/* If Low it is on */
+	if (g_ledmap[led] != 0) {
+		return !stm32_gpioread(g_ledmap[led]);
+	}
+
+	return false;
+}
+
+__EXPORT void led_on(int led)
+{
+	phy_set_led(xlat(led), true);
+}
+
+__EXPORT void led_off(int led)
+{
+	phy_set_led(xlat(led), false);
+}
+
+__EXPORT void led_toggle(int led)
+{
+	phy_set_led(xlat(led), !phy_get_led(xlat(led)));
+}
+
+#ifdef CONFIG_ARCH_LEDS
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_autoled_initialize
+ ****************************************************************************/
+
+void board_autoled_initialize(void)
+{
+	led_init();
+}
+
+/****************************************************************************
+ * Name: board_autoled_on
+ ****************************************************************************/
+
+void board_autoled_on(int led)
+{
+	if (!nuttx_owns_leds) {
+		return;
+	}
+
+	switch (led) {
+	default:
+		break;
+
+	case LED_HEAPALLOCATE:
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_IRQSENABLED:
+		phy_set_led(BOARD_LED_BLUE, false);
+		phy_set_led(BOARD_LED_GREEN, true);
+		break;
+
+	case LED_STACKCREATED:
+		phy_set_led(BOARD_LED_GREEN, true);
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_INIRQ:
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_SIGNAL:
+		phy_set_led(BOARD_LED_GREEN, true);
+		break;
+
+	case LED_ASSERTION:
+		phy_set_led(BOARD_LED_RED, true);
+		phy_set_led(BOARD_LED_BLUE, true);
+		break;
+
+	case LED_PANIC:
+		phy_set_led(BOARD_LED_RED, true);
+		break;
+
+	case LED_IDLE : /* IDLE */
+		phy_set_led(BOARD_LED_RED, true);
+		break;
+	}
+}
+
+/****************************************************************************
+ * Name: board_autoled_off
+ ****************************************************************************/
+
+void board_autoled_off(int led)
+{
+	if (!nuttx_owns_leds) {
+		return;
+	}
+
+	switch (led) {
+	default:
+		break;
+
+	case LED_SIGNAL:
+		phy_set_led(BOARD_LED_GREEN, false);
+		break;
+
+	case LED_INIRQ:
+		phy_set_led(BOARD_LED_BLUE, false);
+		break;
+
+	case LED_ASSERTION:
+		phy_set_led(BOARD_LED_RED, false);
+		phy_set_led(BOARD_LED_BLUE, false);
+		break;
+
+	case LED_PANIC:
+		phy_set_led(BOARD_LED_RED, false);
+		break;
+
+	case LED_IDLE : /* IDLE */
+		phy_set_led(BOARD_LED_RED, false);
+		break;
+	}
+}
+
+#endif /* CONFIG_ARCH_LEDS */

boards/ark/fpv/src/mtd.cpp

@@ -0,0 +1,55 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2024 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+#include <board_config.h>
+
+#include <nuttx/spi/spi.h>
+#include <px4_platform_common/px4_manifest.h>
+
+static const px4_mft_entry_s mft_mft = {
+	.type = MFT,
+	.pmft = (void *) system_query_manifest,
+};
+
+static const px4_mft_s mft = {
+	.nmft = 1,
+	.mfts = {
+		&mft_mft,
+	}
+};
+
+const px4_mft_s *board_get_manifest(void)
+{
+	return &mft;
+}

boards/ark/fpv/src/sdio.c

@@ -0,0 +1,177 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+#include <board_config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+
+#include "chip.h"
+#include "board_config.h"
+#include "stm32_gpio.h"
+#include "stm32_sdmmc.h"
+
+#ifdef CONFIG_MMCSD
+
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Card detections requires card support and a card detection GPIO */
+
+#define HAVE_NCD   1
+#if !defined(GPIO_SDMMC1_NCD)
+#  undef HAVE_NCD
+#endif
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+static FAR struct sdio_dev_s *sdio_dev;
+#ifdef HAVE_NCD
+static bool g_sd_inserted = 0xff; /* Impossible value */
+#endif
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_ncd_interrupt
+ *
+ * Description:
+ *   Card detect interrupt handler.
+ *
+ ****************************************************************************/
+
+#ifdef HAVE_NCD
+static int stm32_ncd_interrupt(int irq, FAR void *context)
+{
+	bool present;
+
+	present = !stm32_gpioread(GPIO_SDMMC1_NCD);
+
+	if (sdio_dev && present != g_sd_inserted) {
+		sdio_mediachange(sdio_dev, present);
+		g_sd_inserted = present;
+	}
+
+	return OK;
+}
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void)
+{
+	int ret;
+
+#ifdef HAVE_NCD
+	/* Card detect */
+
+	bool cd_status;
+
+	/* Configure the card detect GPIO */
+
+	stm32_configgpio(GPIO_SDMMC1_NCD);
+
+	/* Register an interrupt handler for the card detect pin */
+
+	stm32_gpiosetevent(GPIO_SDMMC1_NCD, true, true, true, stm32_ncd_interrupt);
+#endif
+
+	/* Mount the SDIO-based MMC/SD block driver */
+	/* First, get an instance of the SDIO interface */
+
+	finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO);
+
+	sdio_dev = sdio_initialize(SDIO_SLOTNO);
+
+	if (!sdio_dev) {
+		syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", SDIO_SLOTNO);
+		return -ENODEV;
+	}
+
+	/* Now bind the SDIO interface to the MMC/SD driver */
+
+	finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR);
+
+	ret = mmcsd_slotinitialize(SDIO_MINOR, sdio_dev);
+
+	if (ret != OK) {
+		syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
+		return ret;
+	}
+
+	finfo("Successfully bound SDIO to the MMC/SD driver\n");
+
+#ifdef HAVE_NCD
+	/* Use SD card detect pin to check if a card is g_sd_inserted */
+
+	cd_status = !stm32_gpioread(GPIO_SDMMC1_NCD);
+	finfo("Card detect : %d\n", cd_status);
+
+	sdio_mediachange(sdio_dev, cd_status);
+#else
+	/* Assume that the SD card is inserted.  What choice do we have? */
+
+	sdio_mediachange(sdio_dev, true);
+#endif
+
+	return OK;
+}
+
+#endif /* CONFIG_MMCSD */

boards/ark/fpv/src/spi.cpp

@@ -0,0 +1,57 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2024 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/spi_hw_description.h>
+#include <drivers/drv_sensor.h>
+#include <nuttx/spi/spi.h>
+
+constexpr px4_spi_bus_all_hw_t px4_spi_buses_all_hw[BOARD_NUM_SPI_CFG_HW_VERSIONS] = {
+	initSPIFmumID(ARKFPV_0, {
+		initSPIBus(SPI::Bus::SPI1, {
+			initSPIDevice(DRV_IMU_DEVTYPE_IIM42653, SPI::CS{GPIO::PortI, GPIO::Pin9}, SPI::DRDY{GPIO::PortF, GPIO::Pin2}),
+		}, {GPIO::PortI, GPIO::Pin11}),
+		initSPIBusExternal(SPI::Bus::SPI6, {
+			initSPIConfigExternal(SPI::CS{GPIO::PortI, GPIO::Pin10}, SPI::DRDY{GPIO::PortD, GPIO::Pin11})
+		}),
+	}),
+	initSPIFmumID(ARKFPV_1, { // Placeholder
+		initSPIBus(SPI::Bus::SPI1, {
+			initSPIDevice(DRV_IMU_DEVTYPE_IIM42653, SPI::CS{GPIO::PortI, GPIO::Pin9}, SPI::DRDY{GPIO::PortF, GPIO::Pin2}),
+		}, {GPIO::PortI, GPIO::Pin11}),
+		initSPIBusExternal(SPI::Bus::SPI6, {
+			initSPIConfigExternal(SPI::CS{GPIO::PortI, GPIO::Pin10}, SPI::DRDY{GPIO::PortD, GPIO::Pin11})
+		}),
+	}),
+};
+
+static constexpr bool unused = validateSPIConfig(px4_spi_buses_all_hw);

boards/ark/fpv/src/spix_sync.c

@@ -0,0 +1,309 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2023 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name Airmind nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+* @file spix_sync.c
+*
+*
+*/
+
+#include <px4_platform_common/px4_config.h>
+
+#include <board_config.h>
+
+#include <sys/types.h>
+#include <stdint.h>
+#include <string.h>
+#include <stdlib.h>
+#include <stdbool.h>
+#include <fcntl.h>
+#include <unistd.h>
+#include <stdio.h>
+#include <ctype.h>
+
+
+#include <perf/perf_counter.h>
+#include <systemlib/err.h>
+#include <systemlib/px4_macros.h>
+
+#include <px4_arch/io_timer.h>
+
+#include "spix_sync.h"
+
+#define REG(_tmr, _reg) (*(volatile uint32_t *)(spix_sync_timers[_tmr].base + _reg))
+
+#define rCR1(_tmr)      REG(_tmr, STM32_GTIM_CR1_OFFSET)
+#define rCR2(_tmr)      REG(_tmr, STM32_GTIM_CR2_OFFSET)
+#define rSMCR(_tmr)     REG(_tmr, STM32_GTIM_SMCR_OFFSET)
+#define rDIER(_tmr)     REG(_tmr, STM32_GTIM_DIER_OFFSET)
+#define rSR(_tmr)       REG(_tmr, STM32_GTIM_SR_OFFSET)
+#define rEGR(_tmr)      REG(_tmr, STM32_GTIM_EGR_OFFSET)
+#define rCCMR1(_tmr)    REG(_tmr, STM32_GTIM_CCMR1_OFFSET)
+#define rCCMR2(_tmr)    REG(_tmr, STM32_GTIM_CCMR2_OFFSET)
+#define rCCER(_tmr)     REG(_tmr, STM32_GTIM_CCER_OFFSET)
+#define rCNT(_tmr)      REG(_tmr, STM32_GTIM_CNT_OFFSET)
+#define rPSC(_tmr)      REG(_tmr, STM32_GTIM_PSC_OFFSET)
+#define rARR(_tmr)      REG(_tmr, STM32_GTIM_ARR_OFFSET)
+#define rCCR1(_tmr)     REG(_tmr, STM32_GTIM_CCR1_OFFSET)
+#define rCCR2(_tmr)     REG(_tmr, STM32_GTIM_CCR2_OFFSET)
+#define rCCR3(_tmr)     REG(_tmr, STM32_GTIM_CCR3_OFFSET)
+#define rCCR4(_tmr)     REG(_tmr, STM32_GTIM_CCR4_OFFSET)
+#define rDCR(_tmr)      REG(_tmr, STM32_GTIM_DCR_OFFSET)
+#define rDMAR(_tmr)     REG(_tmr, STM32_GTIM_DMAR_OFFSET)
+#define rBDTR(_tmr)     REG(_tmr, STM32_ATIM_BDTR_OFFSET)
+
+#define BOARD_SPIX_SYNC_PWM_FREQ 1024000
+
+unsigned
+spix_sync_timer_get_period(unsigned timer)
+{
+	return (rARR(timer));
+}
+
+static void spix_sync_timer_init_timer(unsigned timer, unsigned rate)
+{
+	if (spix_sync_timers[timer].base) {
+
+		irqstate_t flags = px4_enter_critical_section();
+
+		/* enable the timer clock before we try to talk to it */
+
+		modifyreg32(spix_sync_timers[timer].clock_register, 0, spix_sync_timers[timer].clock_bit);
+
+		/* disable and configure the timer */
+		rCR1(timer) = 0;
+		rCR2(timer) = 0;
+		rSMCR(timer) = 0;
+		rDIER(timer) = 0;
+		rCCER(timer) = 0;
+		rCCMR1(timer) = 0;
+		rCCMR2(timer) = 0;
+		rCCR1(timer) = 0;
+		rCCR2(timer) = 0;
+		rCCR3(timer) = 0;
+		rCCR4(timer) = 0;
+		rCCER(timer) = 0;
+		rDCR(timer) = 0;
+
+		if ((spix_sync_timers[timer].base == STM32_TIM1_BASE) || (spix_sync_timers[timer].base == STM32_TIM8_BASE)) {
+
+			/* master output enable = on */
+
+			rBDTR(timer) = ATIM_BDTR_MOE;
+		}
+
+		/* If the timer clock source provided as clock_freq is the STM32_APBx_TIMx_CLKIN
+		 * then configure the timer to free-run at 1MHz.
+		 * Otherwise, other frequencies are attainable by adjusting .clock_freq accordingly.
+		 */
+
+		rPSC(timer) = (spix_sync_timers[timer].clock_freq / BOARD_SPIX_SYNC_PWM_FREQ) - 1;
+
+		/* configure the timer to update at the desired rate */
+
+		rARR(timer) = (BOARD_SPIX_SYNC_PWM_FREQ / rate) - 1;
+
+		/* generate an update event; reloads the counter and all registers */
+		rEGR(timer) = GTIM_EGR_UG;
+
+		px4_leave_critical_section(flags);
+	}
+
+}
+
+void spix_sync_channel_init(unsigned channel)
+{
+	/* Only initialize used channels */
+
+	if (spix_sync_channels[channel].timer_channel) {
+
+		unsigned timer = spix_sync_channels[channel].timer_index;
+
+		/* configure the GPIO first */
+		px4_arch_configgpio(spix_sync_channels[channel].gpio_out);
+
+		uint16_t polarity = spix_sync_channels[channel].masks;
+
+		/* configure the channel */
+		switch (spix_sync_channels[channel].timer_channel) {
+		case 1:
+			rCCMR1(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR1_OC1M_SHIFT) | GTIM_CCMR1_OC1PE;
+			rCCER(timer) |= polarity | GTIM_CCER_CC1E;
+			break;
+
+		case 2:
+			rCCMR1(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR1_OC2M_SHIFT) | GTIM_CCMR1_OC2PE;
+			rCCER(timer) |= polarity | GTIM_CCER_CC2E;
+			break;
+
+		case 3:
+			rCCMR2(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR2_OC3M_SHIFT) | GTIM_CCMR2_OC3PE;
+			rCCER(timer) |= polarity | GTIM_CCER_CC3E;
+			break;
+
+		case 4:
+			rCCMR2(timer) |= (GTIM_CCMR_MODE_PWM1 << GTIM_CCMR2_OC4M_SHIFT) | GTIM_CCMR2_OC4PE;
+			rCCER(timer) |= polarity | GTIM_CCER_CC4E;
+			break;
+		}
+	}
+}
+
+int
+spix_sync_servo_set(unsigned channel, uint8_t  cvalue)
+{
+	if (channel >= arraySize(spix_sync_channels)) {
+		return -1;
+	}
+
+	unsigned timer = spix_sync_channels[channel].timer_index;
+
+	/* test timer for validity */
+	if ((spix_sync_timers[timer].base == 0) ||
+	    (spix_sync_channels[channel].gpio_out == 0)) {
+		return -1;
+	}
+
+	unsigned period = spix_sync_timer_get_period(timer);
+
+	unsigned value = (unsigned)cvalue * period / 255;
+
+	/* configure the channel */
+	if (value > 0) {
+		value--;
+	}
+
+
+	switch (spix_sync_channels[channel].timer_channel) {
+	case 1:
+		rCCR1(timer) = value;
+		break;
+
+	case 2:
+		rCCR2(timer) = value;
+		break;
+
+	case 3:
+		rCCR3(timer) = value;
+		break;
+
+	case 4:
+		rCCR4(timer) = value;
+		break;
+
+	default:
+		return -1;
+	}
+
+	return 0;
+}
+
+unsigned spix_sync_servo_get(unsigned channel)
+{
+	if (channel >= 3) {
+		return 0;
+	}
+
+	unsigned timer = spix_sync_channels[channel].timer_index;
+	uint16_t value = 0;
+
+	/* test timer for validity */
+	if ((spix_sync_timers[timer].base == 0) ||
+	    (spix_sync_channels[channel].timer_channel == 0)) {
+		return 0;
+	}
+
+	/* configure the channel */
+	switch (spix_sync_channels[channel].timer_channel) {
+	case 1:
+		value = rCCR1(timer);
+		break;
+
+	case 2:
+		value = rCCR2(timer);
+		break;
+
+	case 3:
+		value = rCCR3(timer);
+		break;
+
+	case 4:
+		value = rCCR4(timer);
+		break;
+	}
+
+	unsigned period = spix_sync_timer_get_period(timer);
+	return ((value + 1) * 255 / period);
+}
+
+int spix_sync_servo_init(unsigned rate)
+{
+	/* do basic timer initialisation first */
+	for (unsigned i = 0; i < arraySize(spix_sync_timers); i++) {
+		spix_sync_timer_init_timer(i, rate);
+	}
+
+	/* now init channels */
+	for (unsigned i = 0; i < arraySize(spix_sync_channels); i++) {
+		spix_sync_channel_init(i);
+	}
+
+	spix_sync_servo_arm(true);
+	return OK;
+}
+
+void
+spix_sync_servo_deinit(void)
+{
+	/* disable the timers */
+	spix_sync_servo_arm(false);
+}
+void
+spix_sync_servo_arm(bool armed)
+{
+	/* iterate timers and arm/disarm appropriately */
+	for (unsigned i = 0; i < arraySize(spix_sync_timers); i++) {
+		if (spix_sync_timers[i].base != 0) {
+			if (armed) {
+				/* force an update to preload all registers */
+				rEGR(i) = GTIM_EGR_UG;
+
+				/* arm requires the timer be enabled */
+				rCR1(i) |= GTIM_CR1_CEN | GTIM_CR1_ARPE;
+
+			} else {
+				rCR1(i) = 0;
+			}
+		}
+	}
+}

boards/ark/fpv/src/spix_sync.h

@@ -0,0 +1,42 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2023 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+__BEGIN_DECLS
+void spix_sync_channel_init(unsigned channel);
+int spix_sync_servo_set(unsigned channel, uint8_t  value);
+unsigned spix_sync_servo_get(unsigned channel);
+int spix_sync_servo_init(unsigned rate);
+void spix_sync_servo_deinit(void);
+void spix_sync_servo_arm(bool armed);
+unsigned spix_sync_timer_get_period(unsigned timer);
+__END_DECLS

boards/ark/fpv/src/timer_config.cpp

@@ -0,0 +1,86 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/io_timer_hw_description.h>
+
+/* Timer allocation
+ *
+ * TIM5_CH4  T FMU_CH1
+ * TIM5_CH3  T FMU_CH2
+ * TIM5_CH2  T FMU_CH3
+ * TIM5_CH1  T FMU_CH4
+ *
+ * TIM8_CH1  T FMU_CH5
+ * TIM8_CH2  T FMU_CH6
+ * TIM8_CH3  T FMU_CH7
+ * TIM8_CH4  T FMU_CH8
+ *
+ * TIM4_CH1  T FMU_CH9
+ *
+ * TIM1_CH1  T SPIX_SYNC              > Pulse or GPIO strobe
+ *
+ * TIM2_CH3  T HEATER                 > PWM OUT or GPIO
+ *
+ * TIM3_CH1  T HRT_TIMER
+ *
+ */
+
+constexpr io_timers_t io_timers[MAX_IO_TIMERS] = {
+	initIOTimer(Timer::Timer5, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer8, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer4, DMA{DMA::Index1}),
+};
+
+constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel4}, {GPIO::PortI, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel3}, {GPIO::PortH, GPIO::Pin12}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel2}, {GPIO::PortH, GPIO::Pin11}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel1}, {GPIO::PortH, GPIO::Pin10}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel1}, {GPIO::PortI, GPIO::Pin5}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel2}, {GPIO::PortI, GPIO::Pin6}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel3}, {GPIO::PortI, GPIO::Pin7}),
+	initIOTimerChannel(io_timers, {Timer::Timer8, Timer::Channel4}, {GPIO::PortI, GPIO::Pin2}),
+	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel1}, {GPIO::PortD, GPIO::Pin12}),
+};
+
+constexpr io_timers_channel_mapping_t io_timers_channel_mapping =
+	initIOTimerChannelMapping(io_timers, timer_io_channels);
+
+
+constexpr io_timers_t spix_sync_timers[MAX_SPIX_SYNC_TIMERS] = {
+	initIOTimer(Timer::Timer1),
+};
+
+constexpr timer_io_channels_t spix_sync_channels[MAX_SPIX_SYNC_TIMERS] = {
+	initIOTimerChannel(spix_sync_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}),
+};

boards/ark/fpv/src/usb.c

@@ -0,0 +1,105 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2016 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file usb.c
+ *
+ * Board-specific USB functions.
+ */
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+
+#include <sys/types.h>
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/usb/usbdev.h>
+#include <nuttx/usb/usbdev_trace.h>
+
+#include "arm_internal.h"
+#include <chip.h>
+#include <stm32_gpio.h>
+#include <stm32_otg.h>
+#include "board_config.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_usbinitialize
+ *
+ * Description:
+ *   Called to setup USB-related GPIO pins for the ARKFMU board.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_usbinitialize(void)
+{
+	/* The OTG FS has an internal soft pull-up */
+
+	/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
+
+#ifdef CONFIG_STM32H7_OTGFS
+	stm32_configgpio(GPIO_OTGFS_VBUS);
+#endif
+}
+
+/************************************************************************************
+ * Name:  stm32_usbsuspend
+ *
+ * Description:
+ *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
+ *   used.  This function is called whenever the USB enters or leaves suspend mode.
+ *   This is an opportunity for the board logic to shutdown clocks, power, etc.
+ *   while the USB is suspended.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
+{
+	uinfo("resume: %d\n", resume);
+}

boards/ark/pi6x/default.px4board

@@ -8,13 +8,16 @@ CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_BROADCOM_AFBRS50=y
+CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_HEATER=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
 CONFIG_COMMON_LIGHT=y
 CONFIG_DRIVERS_MAGNETOMETER_MEMSIC_MMC5983MA=y
+CONFIG_DRIVERS_MAGNETOMETER_ST_IIS2MDC=y
 CONFIG_DRIVERS_OPTICAL_FLOW_PAW3902=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y

boards/ark/pi6x/init/rc.board_defaults

@@ -32,19 +32,10 @@ then
 	param set-default SENS_TEMP_ID 2490378
 fi
 
-param set-default EKF2_BARO_DELAY 13
-param set-default EKF2_BARO_NOISE 0.9
-param set-default EKF2_HGT_REF 2
-param set-default EKF2_MAG_DELAY 100
-param set-default EKF2_MAG_NOISE 0.06
 param set-default EKF2_MULTI_IMU 2
 param set-default EKF2_OF_CTRL 1
-param set-default EKF2_OF_DELAY 48
 param set-default EKF2_OF_N_MIN 0.05
 param set-default EKF2_RNG_A_HMAX 25
-param set-default EKF2_RNG_DELAY 48
-param set-default EKF2_RNG_NOISE 0.03
 param set-default EKF2_RNG_QLTY_T 0.1
-param set-default EKF2_RNG_SFE 0.03
 
 param set-default SENS_FLOW_RATE 150

boards/ark/pi6x/init/rc.board_sensors

@@ -21,8 +21,10 @@ then
 fi
 
 # Internal magnetometer on I2C
-# TODO: Write a driver for the MMC5983MA
-mmc5983ma -I -b 4 start
+if ! iis2mdc -R 4 -I -b 4 start
+then
+	mmc5983ma -I -b 4 start
+fi
 
 # Internal Baro on I2C
 bmp388 -I -b 4 start

boards/atl/mantis-edu/default.px4board

@@ -2,6 +2,7 @@ CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
 CONFIG_BOARD_ARCHITECTURE="cortex-m7"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_MAIERTEK_MPC2520=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
 CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y

boards/bitcraze/crazyflie/default.px4board

@@ -3,6 +3,7 @@ CONFIG_BOARD_ARCHITECTURE="cortex-m4"
 CONFIG_BOARD_CONSTRAINED_FLASH=y
 CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_COMPILE_DEFINITIONS="-Wno-narrowing"
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BAROMETER_LPS25H=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L0X=y
 CONFIG_DRIVERS_GPS=y

boards/bitcraze/crazyflie21/default.px4board

@@ -4,6 +4,7 @@ CONFIG_BOARD_CONSTRAINED_FLASH=y
 CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_COMPILE_DEFINITIONS="-Wno-narrowing"
 CONFIG_DRIVERS_BAROMETER_BMP388=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_VL53L1X=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI088_I2C=y

boards/cuav/nora/default.px4board

@@ -7,12 +7,14 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_COMMON_BAROMETERS=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_HEATER=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y

boards/cuav/x7pro/default.px4board

@@ -6,6 +6,7 @@ CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y

boards/cubepilot/cubeorange/default.px4board

@@ -11,9 +11,11 @@ CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y

boards/cubepilot/cubeorange/nuttx-config/include/board.h

@@ -194,6 +194,12 @@
 
 #define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2     /* ADC 1 2 3 clock source */
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/cubepilot/cubeorangeplus/default.px4board

@@ -11,9 +11,11 @@ CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20649=y

boards/cubepilot/cubeorangeplus/nuttx-config/include/board.h

@@ -195,6 +195,12 @@
 
 #define STM32_RCC_D3CCIPR_ADCSRC     RCC_D3CCIPR_ADCSEL_PLL2     /* ADC 1 2 3 clock source */
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/cubepilot/cubeyellow/default.px4board

@@ -12,6 +12,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/diatone/mamba-f405-mk2/default.px4board

@@ -8,6 +8,7 @@ CONFIG_BOARD_SERIAL_URT6="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y

boards/flywoo/gn-f405/default.px4board

@@ -7,6 +7,7 @@ CONFIG_BOARD_SERIAL_URT6="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y

boards/hkust/nxt-dual/default.px4board

@@ -12,6 +12,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/hkust/nxt-dual/src/hw_config.h

@@ -97,9 +97,9 @@
 #define INTERFACE_USART_CONFIG         "/dev/ttyS5,57600"
 #define BOOT_DELAY_ADDRESS             0x000001a0
 #define BOARD_TYPE                     1013
-#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
-#define BOARD_FLASH_SECTORS            (15)
-#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)
+#define BOARD_FLASH_SECTORS            (14)
+#define BOARD_FLASH_SIZE               (16 * 128 * 1024)
+#define APP_RESERVATION_SIZE 	       (1 * 128 * 1024)
 
 #define OSC_FREQ                       16
 

boards/hkust/nxt-v1/default.px4board

@@ -11,6 +11,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/holybro/durandal-v1/default.px4board

@@ -11,6 +11,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/holybro/kakutef7/default.px4board

@@ -9,6 +9,7 @@ CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20689=y

boards/holybro/kakuteh7/default.px4board

@@ -9,6 +9,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/holybro/kakuteh7mini/default.px4board

@@ -9,6 +9,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/holybro/kakuteh7v2/default.px4board

@@ -9,6 +9,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/holybro/pix32v5/default.px4board

@@ -11,6 +11,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/matek/h743-mini/default.px4board

@@ -7,6 +7,7 @@ CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y

boards/matek/h743-slim/default.px4board

@@ -7,6 +7,7 @@ CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y

boards/matek/h743/default.px4board

@@ -8,6 +8,7 @@ CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y

boards/modalai/fc-v1/default.px4board

@@ -12,6 +12,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/modalai/fc-v2/default.px4board

@@ -12,6 +12,7 @@ CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y

boards/mro/ctrl-zero-classic/default.px4board

@@ -12,6 +12,7 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/ctrl-zero-classic/init/rc.board_defaults

@@ -6,4 +6,5 @@
 param set-default BAT1_V_DIV 10.1
 param set-default BAT1_A_PER_V 17
 
+param set-default GPS_2_CONFIG 202
 param set-default TEL_FRSKY_CONFIG 103

boards/mro/ctrl-zero-classic/nuttx-config/include/board.h

@@ -197,6 +197,12 @@
 
 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/mro/ctrl-zero-f7-oem/default.px4board

@@ -10,6 +10,7 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/ctrl-zero-f7/default.px4board

@@ -9,6 +9,7 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/ctrl-zero-h7-oem/default.px4board

@@ -10,6 +10,7 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/ctrl-zero-h7-oem/nuttx-config/include/board.h

@@ -197,6 +197,12 @@
 
 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/mro/ctrl-zero-h7/default.px4board

@@ -10,6 +10,7 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/ctrl-zero-h7/nuttx-config/include/board.h

@@ -196,6 +196,12 @@
 
 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/mro/pixracerpro/default.px4board

@@ -9,9 +9,11 @@ CONFIG_DRIVERS_BAROMETER_DPS310=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GNSS_SEPTENTRIO=y
 CONFIG_DRIVERS_GPS=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI085=y
 CONFIG_DRIVERS_IMU_BOSCH_BMI088=y

boards/mro/pixracerpro/nuttx-config/include/board.h

@@ -196,6 +196,12 @@
 
 #define STM32_FDCANCLK               STM32_HSE_FREQUENCY
 
+/* UART clock selection */
+/* reset to default to overwrite any changes done by any bootloader */
+
+#define STM32_RCC_D2CCIP2R_USART234578_SEL RCC_D2CCIP2R_USART234578SEL_RCC
+#define STM32_RCC_D2CCIP2R_USART16_SEL     RCC_D2CCIP2R_USART16SEL_RCC
+
 /* FLASH wait states */
 #define BOARD_FLASH_WAITSTATES 2
 

boards/mro/x21-777/default.px4board

@@ -9,6 +9,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/mro/x21/default.px4board

@@ -10,6 +10,7 @@ CONFIG_COMMON_BAROMETERS=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DSHOT=y

boards/nxp/fmuk66-e/default.px4board

@@ -11,6 +11,7 @@ CONFIG_DRIVERS_BAROMETER_MPL3115A2=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_SRF05=y

boards/nxp/fmuk66-v3/default.px4board

@@ -11,6 +11,7 @@ CONFIG_DRIVERS_BAROMETER_MPL3115A2=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
 CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
 CONFIG_COMMON_DISTANCE_SENSOR=y
 CONFIG_DRIVERS_DISTANCE_SENSOR_SRF05=y