* Commander: make low remaining flight time configurable and do not clear
- add _ACT param to disable/warning/RTL this feature
- publish rtl flight time estimate also in RTL, and thus fix re-validation
- make failure message clearer, distinguish from battery low
* battery check: add hysteresis for declaring battery_low_remaining_time false again
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: KonradRudin <98741601+KonradRudin@users.noreply.github.com>
Previously uORB queue size was an awkward mix of runtime configurable (at advertise or IOCTL before allocate), but effectively static with all queue size settings (outside of test code) actually coming from the topic declaration (presently ORB_QUEUE_LENGTH in the .msg). This change finally resolves the inconsistency making the queue size fully static.
Additionally there were some corner cases that the muorb and orb communicator implementation were not correctly handling. This PR provides fixes for those issues. Also correctly sets remote queue lengths now based on the topic definitions.
* Made setting of uORB topic queue size in based on topic definition only
* Fixes to the ModalAI muorb implementation
* Removed libfc sensor from format checks
* msg/TransponderReport.msg ORB_QUEUE_LENGTH 8->16 (was set to higher in AdsbConflict.h
---------
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Daniel Agar <daniel@agar.ca>
1s gives some false positives at boot up, as the airspeed selector only
starts publishing 2s after its startup.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
New thrust and torque control mode added which replaces the previous
actuator mode,
in this mode the rate controllers are disables, the control allocator
is enabled and the used externally provices
vehicle_thrust_setpoints and vehicle_torque_setpoints.
New direct_actuator mode
In direct_actuator mode the control allocator module does not publish
actuator_motors and actuator_servos messages which must instead be
provided extrernally by the user.
Removed old direct mode.
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
- do reporting of breaching in-air only in geofenceCheck
- remove geofence_violation_reason_t
- replace geofence_breached field in GeofenceResult.msg with 3 fields
(one for each GF type: max dist, max alt, custom geofence)
- the warning message after breaching a GF is only done by Commander,
and it's specific to the GF type failure
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Has options *None where the check is disabled, and *Warning, where only a warning is
published (which replaces the high wind warning from the COM_WIND_WARN limit).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Some system are able to dead-reckon for a while after losing GPS or
other sources providing positional feedback. If the estimated position
error grows above the failsafe threshold, the system enters a failsafe
mode. As the position error estimate is growing linerly over time, and
it is recommended to take action before entering the failsafe, we here
warn the user about the imminent failsafe and propose to take manual
control.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Since we changed the threshold for allowing arming from TRIM/2 to AIRSPEED_MAX
is is very unlikely that one needs to disable this check.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
COM_ARMABLE is set to "Disabled" will prevent arming.
This allows to set the parameter when ground demoing a drone or
if it's in maintenance for safety reasons.
Set this flag to true if local position is valid but accuracy low, such that
the operator can be warned before system switches to position-failure failsafe.
Additionally, switch to RTL if currently in Mission or Loiter to try to reach home
or fly out of GNSS-denied area.
Set low accuracy threshold to 50m by default for FW and VTOL.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
In this case it did not cause any problems.
Fixes a compiler warning:
/src/modules/commander/HealthAndArmingChecks/HealthAndArmingChecks.cpp:39:21: error: member ‘HealthAndArmingChecks::_failsafe_flags’ is used uninitialized [-Werror=uninitialized]
39 | _reporter(_failsafe_flags)
| ^~~~~~~~~~~~~~~
Silvan Fuhrer