When disconnecting USB poll returns successfully, but the read returns
-1 with ENOTCONN.
In addition this also ensures there's no busy loop when poll returns an
error.
MAVLink continues to work after reconnecting USB.
* Enhancement: State of health, and max_error value is added. Both shows battery health of SMBUS smart battery.
* Enhancement: BAT_C_MULT parameter is introduced. This is for high-current capable SMBUS-based battery.
As SMBUS only provides 16-bit for current, it could only be +-32768mA which is about +-32A.
But with proper treatment, it could be extended with little accuracy loss.
This factor can be set for individual battery system with available information.
* Relative SOC introduced. Proper SMBUS battery should provide percentage of remaining battery
directly. Therefore it does not have to be computed like before.
* State of Health introduced. Proper SMBUS battery should provide SOH value.
* Max error: this shows estimation error of BMS.
* Enhancement: With smart battery, precise estimation of time remaining is provided
with impedance track. It is unit of minute, so 60 seconds multiplied.
Update rate of this is not fast, but very useful.
Co-authored-by: Hyon Lim <lim@uvify.com>
This commit handles incoming MISSION_REQUEST_LIST messages such that
they are no longer ignored if the previously requested mission has
sent all mission items but the ack has never been received.
This was the cause for frequent "IGN REQUEST LIST: Busy" warnings
* uORB orb_stat() and update(uint64_t *time, void *dst) are now obsolete and have been deleted
* mavlink messages add more advertised checks in streams get_size() check to improve data rate calculation across different scenarios
* add support for unmanned underwater vehicles:
* airframe uuv_generic + uuv_hippocammpus including mav_type = 12 for submarines
* mixer for UUVs with X-shaped thruster setup similar to quadcopter
* add module uuv_att_control for underwater robot attitude control
* add rc.uuv_defaults/apps for autostarting e.g. ekf2 and uuv_att_control app
* Add param for software flow ctl on 3DR radios
* Dont reset telemetry type on radio timeout
* Treat 3DR radio as generic link type
* Rename 3DR to SiK radio
The previous forwarding rules exclude another onboard MAVLink node to
send messages to a specific target.
E.g. a message from a companion computer with sysid 1 (same as
autopilot) with target sysid 190 (for the ground station) was not
forwarded.
With the new rules, anything that is not specifically addressed to the
autopilot's sysid and compid is forwarded.
- split out integrated data into new standalone messages (sensor_accel_integrated and sensor_gyro_integrated)
- publish sensor_gyro at full rate and remove sensor_gyro_control
- limit sensor status publications to 10 Hz
- remove unused accel/gyro raw ADC fields
- add device IDs to sensor_bias and sensor_correction
- vehicle_angular_velocity/vehicle_acceleration: check device ids before using bias and corrections
* Treat UAVS diffrently from manned aviation
* Added fake_traffic testing functionality,
* Added NAV_TRAFF_AVOID Hold and Landmode
* Added Behavior: HOLD Position to collision avoidance mode and implemented Landmode to collision avoidance.
Boards where no Hardware GUID is defined will send 0 as GUID.
Right now collision avoidance for more than one FMU without Hardware GUID is not possible.
We should consider adding a randomly generated HW GUID as a placeholder for legacy Boards
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
* Mavlink: subscribe to airspeed_validated instead of airspeed topic
This e.g. changes the way QGC displays the airspeed in case of an
airspeed failure (0 instead of the last valid airspeed). It will
always display the airspeed that's used currently in the control
modules.
* FW land detector: move to subscribe to airspeed_validated instead of airspeed topic
- the land detector checks further if the airspeed is NAN, in which case
it sets the airspeed to 0 (min groundspeed, vz and accel checks still
have to pass.
* Fixed-wing land detector use airspeed_vaidated: addressed review comments
- replaced ternary by conditional
- set airspeed to 0 if airspeed_validated stops publishing
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Daniel Agar