Heading offset was configured as radians but should be configured as
degrees on Septentrio receivers. The parameter was already in degrees
but the configuration logic was changing it into radians. Also allow the
entire allowed range of heading offset values for Septentrio receivers.
The documentation for `SEP_DUMP_COMM` was quite unclear and users had to
use the user guide to find out what exactly it did. The new
documentation tries to make the purpose clearer.
This fixes an incorrect check of the device paths during instantiation
of the Septentrio driver that caused the driver to start and not print
an error message.
- track accel clipping count per axis
- only set bad_acc_clipping fault_status if at least one axis is
clipping continuously or if all have been clipping at warning level
- Note: this doesn't impact the clipping projections that boost the
accel process noise, pause bias estimation, and skip gravity fusion
on a per sample basis
- Fixes matplotlib version expression from ">=3.0.*" ro ">=3.0" which is the right syntax
Fixes issue #23329
Co-authored-by: lee wonwoo <leewonwoo@leeui-MacBookPro.local>
We had a case where someone took off with an experimental
system with 100% RAM usage on the embedded system
without noticing. This lead to problems during flight.
Since we already have a CPU load check it seems natural
to also check the reported RAM usage.
- new parameter EKF2_LOG_VERBOSE to enable (currently enabled by default)
- force advertise topics immediately (based on EKF2_LOG_VERBOSE and per aid source configuration)
- logger optionally log all estimator topics at minimal rate
When using optical flow for terrain aiding, we cannot assume that the
terrain estimate is valid if flow is fused as is can only be observed
during motion. When no direct observation is available, the terrain is
assumed to be valid if its 1sigma uncertainty is < 10% of the hagl.
Terrain is the state: terrain vertical position
Hagl (height above ground level) is the vertical distance between the
vertical position and the terrain vertical position
* mission: skip a vtol takoff mission item if already in air and a fixed wing
* MissionBase: also skip FW takeoff when already in-air
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* mission: use setNextMissionItem to skip vtol takeoff when already in air
* mission: Only skip the VTOL takeoff in air for mission and rtl mission
If flying RTL mission reverse it must still include the takeoff point.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Without this flag the command silently succeeds even though the logs contains
an error. It's much more developer friendly to fail early in case of an error.
The log path is then also shown in the console output.
- GPS drivers in PX4/Firmware (c29d189788090f6994e488f65789a8fe6b835d8d): d92cf3a2b2
- GPS drivers current upstream: 0b79ec4dbe
- Changes: d92cf3a2b2...0b79ec4dbe
0b79ec4 2024-04-12 Thomas Frans - sbf: fix issue with automatic base config in QGC
5810dac 2024-04-12 Thomas Frans - style: add editorconfig file for consistent style
915024c 2024-03-26 Julian Oes - sbf: fix subsequent init in QGC
3ea1d76 2024-03-04 Julian Oes - sbf: don't foget to configure RTCM
c6da592 2024-03-04 Julian Oes - sbf: don't change baudrate of USB port
Co-authored-by: PX4 BuildBot <bot@px4.io>
- mavlink in PX4/Firmware (7d9b119283b5aff3976431bd48e4308a0bce7b56): 9e0d01df69
- mavlink current upstream: da3223ff93
- Changes: 9e0d01df69...da3223ff93
da3223ff 2024-06-13 Thomas Frans - gps: add status and integrity information (#2110)
- MPC_VEL_LP: new velocity first order low pass filter (off by default)
- MPC_VEL_NF_FRQ/MPC_VEL_NF_BW: new velocity notch filter (off by default)
- MPC_VELD_LP: existing velocity derivative low pass filter, but I've dropped the remaining controllib usage
