This system command will display, set and save the network
settings.
netman show - Displays the current settings.
netman update - Will check for a net.cfg file on the SD card.
If present, it will update the paramaters,
delete the file, and reboot. Using the new settings.
netman save - Saves the current settings to net.cfg on the SD card.
This file shoulf be renamed to preserver it across
reboots or editited to chech networkin paramates.
File format is name<space>value:
echo DEVICE=eth0 > /fs/microsd/net.cfg
echo BOOTPROTO=fallback >> /fs/microsd/net.cfg
echo IPADDR=192.168.0.4 >> /fs/microsd/net.cfg
echo NETMASK=255.255.255.0 >>/fs/microsd/net.cfg
echo ROUTER=192.168.0.254 >>/fs/microsd/net.cfg
echo DNS=192.168.0.254 >>/fs/microsd/net.cfg
Valid values for `proto` are `dhcp`, `static`, `falback`
Both will try dhcp for CONFIG_NETINIT_FALLBACK times
and fall back to the static address.
NETMASK - is the network mask.
IPADDR - this nodes ip address for static or fall back.
ROUTER - The default route.
DNS - The address of the dns server.
- generate PWM_MAIN 1-14
- generate PWM_AUX 1-8
- generate PWM_EXTRA 1-8
- px4io and pwm_out directly read configuration parameters
- only available and active physical outputs are actually shown for configuration
- overall saves flash despite adding many new parameters
- control allocation module with multirotor, VTOL standard, and tiltrotor support
- angular_velocity_controller
- See https://github.com/PX4/PX4-Autopilot/pull/13351 for details
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Roman Bapst <bapstroman@gmail.com>
- commander preflightcheck use estimator_sensor_bias message instead of EKF state index magic number
- ekf2 publish estimated bias limits in estimator_sensor_bias
- preflightcheck only error if bias estimate exceeds half of configured limit (delete COM_ARM_EKF_AB and COM_ARM_EKF_GB parameters)
- ekf2 can now run in multi-instance mode (currently up to 9 instances)
- in multi mode all estimates are published to alternate topics (eg estimator_attitude instead of vehicle_attitude)
- new ekf2 selector runs in multi-instance mode to monitor and compare all instances, selecting a primary (eg N x estimator_attitude => vehicle_attitude)
- sensors module accel & gyro inconsistency checks are now relative to the mean of all instances, rather than the current primary (when active ekf2 selector is responsible for choosing primary accel & gyro)
- existing consumers of estimator_status must check estimator_selector_status to select current primary instance status
- ekf2 single instance mode is still fully supported and the default
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- add new parameter `IMU_GYRO_FFT_EN` to start
- add 75% overlap in buffer to increase FFT update rate
- space out FFT calls (no more than 1 per cycle)
- increase `IMU_GYRO_FFT_MIN` default
- decrease main stack usage
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
Nuttx now supports sh and source (.)
sh will open a new process for each invocation.
This means the child can not modify the parent
env. So we must use . to matain how nuttx worked.
Since rc.vehicle_setup is used in both we use
source and alis as we did with sh.
