Overhauls the DShot driver with per-timer BDShot selection, multi-timer
sequential capture, Extended DShot Telemetry (EDT), and AM32 ESC EEPROM
read/write via MAVLink. Expands ESC support from 8 to 12 channels.
BDShot:
- Per-timer BDShot protocol selection via actuator config UI
- Multi-timer sequential burst/capture on any DMA-capable timer
- Adaptive per-channel GCR bitstream decoding
- Per-channel online/offline detection with hysteresis
Extended DShot Telemetry (EDT):
- Temperature, voltage, current from BDShot frames (no serial wire)
- New DSHOT_BIDIR_EDT parameter
- EDT data merged with serial telemetry when both available
AM32 EEPROM:
- Read/write AM32 ESC settings via MAVLink ESC_EEPROM message
- ESCSettingsInterface abstraction for future ESC firmware types
- New DSHOT_ESC_TYPE parameter
Other changes:
- Per-motor pole count params DSHOT_MOT_POL1–12 (replaces MOT_POLE_COUNT)
- EscStatus/EscReport expanded to 12 ESCs with uint16 bitmasks
- Numerous bounds-check, overflow, and concurrency fixes
- Updated DShot documentation
* heater: add multi-instance support, refactor parameter handling, remove legacy params file
This change introduces multi-instance heater support to allow independent temperature control for multiple IMUs.
Main changes:
- Add support for multiple heater instances
- Refactor parameter handling to use per-instance parameters
- Remove the legacy parameter file and migrate to the updated parameter structure
This improves scalability and makes heater configuration consistent across setups with multiple sensors.
* Refactor heater configuration across multiple boards
- Updated heater GPIO definitions to introduce a new naming convention for better clarity and consistency.
- Replaced `GPIO_HEATER_OUTPUT` with `GPIO_HEATER1_OUTPUT` and adjusted the corresponding output enable macros.
- Changed parameter names from `SENS_TEMP_ID` to `HEATER1_IMU_ID` in various board default configurations to reflect the new heater setup.
- Ensured all affected board configurations are updated to maintain functionality with the new heater definitions.
* heater: fix missing HEATER1_OUTPUT_EN control
* heater: fix more missing HEATER1_OUTPUT_EN control
* heater: tidy config, docs, and instance handling
- Remove unused controller period member and use CONTROLLER_PERIOD_DEFAULT
- Improve HEATER${i}_IMU_ID description and instance-related logging/behavior
- Add a guard when HEATER_NUM exceeds HEATER_MAX_INSTANCES
Note: drop intermediate/reverted change around the 'celsius' spelling.
* heater: refactor constructor to remove unused parameter and add instance name function
- Remove unused ModuleParams argument from Heater constructor
- Add heater_instance_name() helper to provide per-instance work queue task names
- Use instance-specific parameter lookup (HEATER{n}_*) during initialization
Use heater_instance_name() to label each instance (heater_1/2/3) in work queue.
Also drop unused ModuleParams argument from constructor and keep per-instance
parameter handle lookup in initialization.
* format
* board: update GPIO configuration for multiple heater instances, add HEATER_NUM for boards using PX4IO
* heater: update heater control to use HEATER1_OUTPUT_EN when using PX4IO for consistency
* heater: add a TODO for px4io multi-instance
* heater: update missing GPIO_HEATER1_OUTPUT in sky-drones
* heater: fix multiple newlines at EOF (resolve CI check failure)
* heater: switch to PublicationMulti for heater_status and log multi-instance
- Changed _heater_status_pub from Publication to PublicationMulti to support independent per-instance publications without overwriting.
- Updated logged_topics.cpp to use add_optional_topic_multi("heater_status")
This fixes the issue where multiple heater instances were writing to the same heater_status topic, causing data overwriting and incorrect update rates in logs.
---------
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
- Initialize W25N01GV NAND flash on SPI1 with littlefs.
- Enable BOARD_SMALL_FLASH_LOGGING for small flash handling.
- Increase logger buffer size for flash write performance.
I don't think we have a way to explicitly detect if BAT1 or BAT2
"bricks" are correct, so we have to assume they are, and rely on the
voltage/current shown.
Additionally, we can now power cycle sensor power.
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
This configures the RTC clock to use the HSE instead of the not existing
LSE clock which prevents boot waiting for the not existing LSE crystal
for a few seconds on startup.
* Bidirectional DShot
Co-authored-by: Julian Oes <julian@oes.ch>
* f4/f1 support, not supported
* fix f1 build target
* sanity check timer_channel value, fix CCxNP ifdef, debug stuff
* removed debug code, added define for H7 HAVE_GTIM_CCXNP
* round robin sampling for less than 4 DMA
* unlimited esc_status logging
* dshot: fix formatting
* dshot: add define for number of DMA channels to use
This allows individual boards to override the number of DShot channels
and hence avoid round robin capture of the RPM feedback.
* ARK: enable 4 DMA channels for DShot on 6X
* dshot: publish when all channels are updated
This slows down the ESC_STATUS publication in the case of round robin
capture. E.g. for 800 Hz output with one DMA channel, the ESC_STATUS is
now published at 200 Hz.
* dshot: avoid duplicate publications for bidir and telem
Instead of publishing both bidirectional dshot updates as well as
telemetry updates, we now combine the data from both streams, and
publish whenever we get RPM updates, as the latter arrives with higher
rate, e.g. 200 Hz with round robin, or faster otherwise.
When combining the data, we take RPM from bidirectional dshot, and the
rest from telemetry.
When we have only one of the two, either telemetry or bidirectional
dshot, we just publish that one.
* boards: add ark fpv and pi6x BOARD_DMA_NUM_DSHOT_CHANNELS
* dshot: turn off debug build
---------
Co-authored-by: Julian Oes <julian@oes.ch>
Co-authored-by: alexklimaj <alex@arkelectron.com>
* boards: change board ID of KakuteH7 mini
Holybro would like to consolidate the board ID to what is used in
ArduPilot.
* boards: update KakuteH7mini bootloader
This is due to the board ID change.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
Jacob Dahl