* ZMO airframe: update parameters
Including some parameters we found useful during the tests over the
previous months:
- various controller & transition tuning refinements
- remove battery capacity (not reliable enough w battery degradation)
- airspeed scale
- rotor configs:
- remove everything related to rotors 3 and 4 (which don't exist)
- set moment coefficients explicitly even if at default
- Increase roll limit (FW_R_LIM, FD_FAIL_R)
- min and max airspeeds
- tilt servo min and default PWM values
* ZMO airframe: address review
- explicitly set CA_ROTOR3_* to 0 (as these are set in the parent
13100 which describes a quadrotor)
- remove ASPD_SCALE_1 (close enough to default, and better to have
slightly low reading)
- remove MPC_ACC_HOR_MAX (= default)
- remove MPC_TILTMAX_AIR (was temporary)
- remove SENS_EN_SF1XX (= default)
* ZMO airframe: update tilt setup
to describe a setup where tilt servos can provide yaw torque in both
directions in multicopter mode.
* ZMO airframe: wording
* Update ulog_file_format.md
Update Known Parser Implementations with updated information for Foxglove and the typescript parser
* Update docs/en/dev_log/ulog_file_format.md
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
* Docs: add moving platform
documenting the addition in #24471
* Moving platform docs: address review
- Release note, write release in docs
- Describe configuration also in main gazebo sim docs, syntax section
- Tip that plugin can be used in other worlds, linking to plugin readme
* Update docs/en/sim_gazebo_gz/index.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Rescale throttle curve to HTE as option
* Add slew rate to hover thrust estimate
* Update docs to reflect changes
Fix formating
* mc_att_control: suggestions for hover thrust slewing
- Slower slew rate
- Move update of hover thrust estimate into main loop
- Make sure dt for slew rate is correct
- Apply parameter updates if hover thrust estimate not used
- Parameter description in metadata files
* fix: Rescaling cases order
* Rescale to HTE estimate by default
* Update src/modules/mc_pos_control/multicopter_position_control_params.c
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
* Fix hte sub name
* Update MPC_THR_CURVE description
* Swap thr curve values to make hte rescaling default for value 0
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
* Updated Encrypted logs docs to reflect https://github.com/PX4/PX4-Autopilot/pull/24489
* Subedit
* Subedit the key generation bit
* Updated the docs with multiple command line args for the decryptor and added OpenSSL as a requirement
* Subedit
* Update log_encryption.md
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
