external mode has been running. Also don't publish if we are not controlling anything,
e.g. in rotary wing mode
Signed-off-by: RomanBapst <bapstroman@gmail.com>
add RunwayControl messge to pass wheel steering controls to wheel controller
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Runway takeoff: specify that RWTO_TKOFF is directly applied during takeoff
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
msg/RateCtrlStatus: remove unused wheel_rate_integ field
The wheel rate controller is not run in the moduels that are now
running the MC/FW rate controllers, so thsi field canot be filled.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
wheel rate controller: use speed scaler quadratically on integrator
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
wheel yaw controller: use a time constant of 0.1
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
FW Attitude Controller: lock heading setpoint for wheels to initial heading
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Params that are used by FW Mode Manager
- FW NPFG: NPFG params, should be renamed to FW Lateral Control once moved to the lat/lon controller
- FW Auto Takeoff
- FW Auto Landing
Params used by Fw Lat/Long Controller:
- FW Lateral Control
- FW Longitudinal Control
Params used by both:
- FW General
Params used by Performance model:
- FW Performance (could be moerged with FW General?)
Signed-off-by: Silvan <silvan@auterion.com>
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
It turns out that we set the ADC range incorrectly leading to the
measured current being capped at a certain level as the ADC on the
sensor saturates.
Instead, we need to set the range according to the formula given in the
interface datasheet.
* adis16507: enhance driver to handle and recover from all failure modes
- Clean up driver
- Add optional hardware reset
- Fix scale and range for 125 deg/s variant
- Handle communication errors when read returns zeroes
- Improved perf counters
* change prints to PX4_DEBUG, define BURST_READ_CMD, do both soft and hard reset, use ScheduleNow instead of 1ms delay, change read/write stall period to SPI_STALL value
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
* gz: print version number in init, remove gst plugin spam, rename function
* fix 0 timestamp issue by waiting for clock callback before subscribing to other topics. Refactor to cleanup topic subscriptions
* format
* change gzerr to gzwarn
- only use data from airspeed_validated topic if source is SENSOR
- add 1s timeout (set to NAN if older)
- use FW_USE_AIRSPD consitently (treat the same as CAS=NAN)
Signed-off-by: Silvan <silvan@auterion.com>
Silvan Fuhrer