Replace the existing check for the availability of a takeoff mission item with a combined
check for takeoff and landing item (or landing pattern). New param MIS_TKO_LAND_REQ
can be set to require only a takeoff, only a landing, both takeoff and landing, and
both or none. The latter is meant to be set if is e.g. deemed unsafe to start a flight
through a Takeoff WP without though defining a Landing - as then in case of a RTL the
vehicle doesn't follow a pre-defined path but instead only can do default RTL that especially
for FW and VTOL isn't always safe.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Previously the minimum airspeed setpoint was adjusted to the load_factor compensated
stall speed, which, when the stall speed was set without margin, gave the controller
no room for error (the vehicle would stall if the controller has even a small airspeed
error).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* LandDetectorMC: enforce that LNDMC_Z_VEL_MAX * 1.2 is below *MPC_LAND_CRWL/MPC_LAND_SPEED
Otherwise the _in_descend flag doesn't get set correctly during the last part
of the landing, where the descend speed is at MPC_LAND_CRWL or LAND_SPEED.
The _in_descend flag is set it the velocity setpoint is >1.1*LNDMC_Z_VEL_MAX.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
- in a lot of cases this won't really matter, although you can see it in logs (especially with things like vehicle_at_rest), but it's something we might as well do properly
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
Fixes a regression from 8bae4e5c0e, where
the orbit flight task wasn't an extra task (flight_tasks_to_add) anymore
and therefore the command handling wasn't generated.
There was a race condition that could cause several outcomes. The most severe
was that flight_mode_manager gets the command, switches to orbit and then
in the next iteration switches back because commander did not change
nav_state yet. When commander then switches, flight_mode_manager would still
be in the old mode.
This is prevented by storing the command (allowing it to arrive before or
after mode switch), and then apply it after the switch happens.
- vehicle_angular_velocity and vehicle_angular_acceleration are produced together from the same input data, consumed together, and share the the same metadata (timestamps)
- individually these topics each have 16 bytes of metadata (2 timestamps) for 12 bytes of data (x,y,z float32)
During the whole flight, if the difference between the yaw estimate from
EKF2 and the emergency estimator is large and that the GNSS velocity
fusion is failing continuously, immediately reset to the emergency yaw
estimate.
- with Ekf::initialiseFilter() resetting _time_last_hagl_fuse the terrain estimate was technically valid regardless of any range or flow data availability and as a result optical flow fusion is able to start and stay active
- only consider terrain estimate valid based on control status flags and recent fusion
The CameraFeedback module used only the vehicle attitude for the camera orientation so far. With this change, the gimbal_device_attitude_status is used to compute the global camera orientation when a gimbal is used.
In this case it did not cause any problems.
Fixes a compiler warning:
/src/modules/commander/HealthAndArmingChecks/HealthAndArmingChecks.cpp:39:21: error: member ‘HealthAndArmingChecks::_failsafe_flags’ is used uninitialized [-Werror=uninitialized]
39 | _reporter(_failsafe_flags)
| ^~~~~~~~~~~~~~~
* simulator_mavlink: Add basic vio failure injection
Signed-off-by: Paul Frivold <paul@kefrobotics.com>
* simulator_mavlink: Rm failure not supported warning
Failures commands are also handled in other files,
so warning here could be confusing.
Signed-off-by: Paul Frivold <paul@kefrobotics.com>
Signed-off-by: Paul Frivold <paul@kefrobotics.com>
Silvan Fuhrer