a9ec1a35bc
divide lat/lon received from HIL_STATE_QUATERNION msg by 1E7
2017-04-13 11:18:10 +02:00
2955a2c317
simulator: typo in initial output message
2017-04-12 18:58:37 +02:00
1302b6a796
inav: check for updated baro in baro_offset calculation
2017-04-11 06:24:41 +02:00
24380ae88c
logger: add SDLOG_DIRS_MAX param to limit the max number of log directories
...
Disabled by default, so that logs are not deleted unexpectedly.
2017-04-10 23:37:09 +02:00
7f0db95f87
logger: reduce CPU load by ~1.5%
...
Reduces CPU load from ~6.9% to 5.3% (tested on Pixracer & Pixhawk). The
method is only used once, so it does not increase flash usage.
2017-04-10 23:37:09 +02:00
75bd4f1121
logger: implement a logrotate
...
Remove old log directories on startup if free space falls below a threshold.
The threshold is 300MB or 10% of the disk capacity if that's smaller.
2017-04-10 23:37:09 +02:00
85b074f8d8
Navigator: Fix RTL state sequence
2017-04-10 23:34:35 +02:00
83cf4fb16e
cmake multi_tables.py dependency
2017-04-10 23:31:56 +02:00
5fd7f2fa6f
Navigator: Clean up of mission block init
2017-04-10 23:18:40 +02:00
8687d414bf
mc_pos_control: new variable that defines speed in manual controlled mode
2017-04-10 21:34:00 +02:00
0b8e88f476
fw_pos_control_l1 remove unnecessary ground_speed
2017-04-10 09:41:01 +02:00
dc30498c80
fw_pos_control_l1 control_position split position_setpoint_triplet
2017-04-10 09:41:01 +02:00
0b0c552dee
fw_pos_control_l1 remove unused ground_speed arg
2017-04-10 09:41:01 +02:00
af7b2cd22f
fw_pos_control_l1 cleanup init and uorb helpers
2017-04-10 09:41:01 +02:00
474ce2851e
fw_pos_control_l1 using math constrain, max, min, radians
2017-04-10 09:41:01 +02:00
8b4877a6eb
fw_pos_control_l1 delete unused terrain helper
2017-04-10 09:41:01 +02:00
c5e0bf1c2f
uORB combine VTOL FW and MC virtual topics ( #7008 )
2017-04-09 13:17:20 -04:00
19f0b0be3a
Navigator: Altitude acceptance to switch to new waypoints should be more accurace than horizontal distance by default
2017-04-09 17:25:38 +02:00
3b743fbbe9
MC position control: Smoother takeoff
...
This patch ramps up the throttle to hover throttle instead of a fixed value and limits the vertical takeoff speed to the value set in the parameter. This should ensure smoother, slower takeoffs, in particular in autonomous flight modes.
2017-04-09 17:22:58 +02:00
61cd89efc1
Land detector: Since multicopters take off and land slower than 0.7 m/s, setting the default detection threshold to 0.5 m/s is a much safer default
2017-04-09 17:22:58 +02:00
4ff3fb4dee
mc_pos_control: if takeoff setpoint in auto mode, then do not enter ground contact
2017-04-09 17:19:28 +02:00
08cf97c687
Commander: indicate failsafe reasons more clearly
2017-04-09 12:40:34 +02:00
f74d6e443e
Navigator: Initialize RTL state properly
2017-04-08 07:58:37 +02:00
5788701cc7
Replaced warn() with PX4_WARN()
2017-04-06 12:05:57 +02:00
02a9ccc4f2
Removed dependency on <algorithm>
2017-04-06 12:05:57 +02:00
098b57534d
UAVCAN GNSS bridge: proper handling of various time bases
2017-04-06 12:05:57 +02:00
8e61ed9b77
Republishing GNSS Fix2 if no GNSS publishers are available on the bus
2017-04-06 12:05:57 +02:00
14249d3318
UAVCAN GNSS bridge status output shows whether support for the old Fix message is active
2017-04-06 12:05:57 +02:00
75c45b62d7
UAVCAN GNSS Fix2 handling
2017-04-06 12:05:57 +02:00
32ac1288ba
Libuavcan update
2017-04-06 12:05:57 +02:00
044a767235
param: add PARAM_NO_AUTOSAVE: if defined, do not depend on LP work queue
...
Some NuttX configs do not have the work queues enabled.
2017-04-06 11:49:03 +02:00
1be639ec46
temperature_calibration: turn off param autosave
2017-04-06 11:49:03 +02:00
43afb8d41e
sensor calibration: remove param_save_default() calls
2017-04-06 11:49:03 +02:00
4b18f8ea46
LandDetector: remove param_notify_changes()
...
not needed anymore because of autosave
2017-04-06 11:49:03 +02:00
dffba3e03b
param: move variable definitions to the top of the file
2017-04-06 11:49:03 +02:00
a0e2b0c5a2
param: add param_control_autosave to enable/disable autosave
2017-04-06 11:49:03 +02:00
f3e9739ab0
param export: use writer lock
...
to protect against concurrent writes to the same file
2017-04-06 11:49:03 +02:00
a5cdff06d5
param: implement rate-limited autosave
...
- add a saving delay of 300ms
- save at most once every 2 seconds
2017-04-06 11:49:03 +02:00
7c43689ddc
commander: remove param autosave
2017-04-06 11:49:03 +02:00
f179049e95
replay: ignore the ULogMessageType::INFO message
...
This got introduced the the addition of the perf counter to the log.
Fixes the error:
unknown log message type 73
2017-04-06 11:48:35 +02:00
c7d9a7a6d1
mavlink_log_handler: fix potential buffer overflow
2017-04-06 11:48:35 +02:00
b0ee1579a9
local_position_estimator: fix typo in params
2017-04-06 11:48:35 +02:00
04303dcf72
PreflightCheck: use orb_unsubscribe instead of px4_close
2017-04-06 11:48:35 +02:00
a6eb0053c5
TECS default FW_T_HRATE_FF 0.8
2017-04-05 09:31:20 +02:00
22d0e507c6
TECS fix height demand change
2017-04-05 09:31:20 +02:00
0158f1d506
VTOL Standard transition improvements ( #6904 )
...
* FW actuators fully on the entirety of front and back transition
* back transition ramp up to full MC weight half way through back transition
* increase maximum front and back transition times
* navigator don't reset transition altitude
2017-04-02 19:39:39 -04:00
1d681b0356
Update URL in airspeed calibration error message
...
When a FW/VTOL system detects a missing airspeed sensor, it produces an error message.
This patch uses the new relevant URLs in the PX4 documentation.
Fixes #4549
2017-04-03 00:25:24 +02:00
e8e4e5be49
land detector : add stbs for altitude
2017-04-02 21:52:18 +02:00
5f135acf33
Land detector: Add mode for rovers
2017-04-02 21:52:18 +02:00
d1c3b771ee
Update navigator_main.cpp
...
fix a spell error
2017-04-02 12:15:10 +02:00
Mohamed Abdelkader Zahana