RT7 Boot from debugger now
RT7 Version OCOTP GUID/Rev Fix
RT7 I2C & SPI Partly working
RT7 Add FRAM support
Co-authored-by: David Sidrane <david.sidrane@nscdg.com>
nxp_imxrt1170-evk:Finish 1170 iomux versioning
With Networking
Memory region Used Size Region Size %age Used
flash: 722108 B 7 MB 9.84%
flashxip: 909032 B 1 MB 86.69%
sram: 780212 B 856 KB 89.01%
itcm: 0 GB 0 GB
dtcm: 0 GB 128 KB 0.00%
total used free largest nused nfree
total used free largest nused nfree
Umem: 267232 229136 38096 37264 906 53
No Network
[846/848] Linking CXX executable nxp_fmurt1062-v2_default.elf
Memory region Used Size Region Size %age Used
flash: 685340 B 7 MB 9.34%
flashxip: 895448 B 1 MB 85.40%
sram: 722356 B 856 KB 82.41%
itcm: 0 GB 0 GB
dtcm: 0 GB 128 KB 0.00%
total used free largest nused nfree
Umem: 325088 200992 124096 123376 813 46
This commit With Networking
[4/6] Linking CXX executable nxp_fmurt1062-v2_default.elf
Memory region Used Size Region Size %age Used
flash: 694852 B 7 MB 9.47%
flashxip: 936880 B 1 MB 89.35%
sram: 753588 B 856 KB 85.97%
itcm: 0 GB 0 GB
dtcm: 0 GB 128 KB 0.00%
total used free largest nused nfree
Umem: 293856 228432 65424 64448 900 51
px4io_update: Add px4io FW on nxp_fmurt1062-v2
nxp_fmurt1062-v2:Use DMA on SPI
nxp_fmurt1062-v2:Timer configuration for 1 channel per group (timer)
nxp_fmurt1062-v2:Normalize with V5X - start PX4IO and Mavlink on TELEM2
nxp_fmurt1062-v2:Update PX4IO Firmware
nxp_fmurt1062-v2:Normalize boardconfig to upstream
nxp_fmurt1062-v2:Corect roataion of ICM20602
nxp_fmurt1062-v2 RC04 HW Changes
nxp_fmurt1062-v2:Use TJA1103 PHY
nxp_fmurt1062-v2:Update to NuttX 10.3+
nxp_fmurt1062:Use Buffer based HW flow control
nxp_fmurt1062-v2:Free Memory
nxp_fmurt1062-v2:Remove fixed wing
* Cyphal: fix comparing floating-point issue
* Cyphal: fix setpoint serialization
* Cyphal: fix bug with wrong comparasion of param name and pub/sub name: remove prefix from UavcanPublisher::updateParam and UavcanDynamicPortSubscriber::updateParam and PublicationManager::updateDynamicPublications
* Cyphal: integrate UavcanEscController with PublicationManager, remove second instance of UavcanEscController from CyphalNode
* Cyphal: publish readiness with minimal frequency because according to UDRAL The drive shall enter STANDBY state automatically if the readiness subject is not updated for CONTROL_TIMEOUT
* Cyphal: increase setpoint publish rate from ~75 to 200 by removing PX4_INFO (it really significantly react on the the output rate) and changing the mixing output rate and the shedule interval
* Cyphal: restore prefix because we need it for uorb over uavcan/cyphal and add udral prefix for non uorb pub/sub
* Cyphal: fix DynamicPortSubscriber subscription: if it has multiple subscribers, it should call subscription only after updating of all port subscribers port identifiers
* Cyphal: fix SubscriptionManager: we should take care about prefix
* Cyphal: fix readiness for test motor mode
* [Cyphal] Fix dynamicsubscription, improve printinfo, enable MR-CANHUBK3 config
---------
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
David Sidrane