Camera controls should not happen through the flight controller, and
the control allocation has no means of controlling the camera zoom.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When requesting a message from a stream that is not active we start the
stream with interval=0 and call the request method once. For all streams
this works fine except the gps_global_origin. For this one the request method
is actually overidden to throttle down the rate and not just send out the message.
This will cause this message to never being sent on request if the stream
is not active by default.
Prior commit added opening of /dev/null as 0, 1 and/or 2 file
descriptors, if they where not present. However, if the temporary
file descriptor used to open /dev/null matched the target file
descriptor, it would be immediately closed again. This commit fixes that,
and does not duplicate and close the temporary file descriptor if it is
already at the correct number.
If 0, 1 and/or 2 file descriptors are not open when mavlink module
starts (as might be the case for USB auto-start), use default /dev/null
so that these numbers are not used by other other files.
Instead of interpret a request for "more logs than currently exists" as
a new request, use a request for index 0, which is more likely to be
the first request.
Previously, it was not possible to enable forwarding of messages to/from
teh USB instance because it does not have a param for it, like the
serial instances have.
With this commit, we change the default to always set forwarding on for
the USB instance as that is likely desired.
Signed-off-by: Julian Oes <julian@oes.ch>
When we receive a command_long or command_int message to
answer, it arrives with a source sysid/compid, so this means we can send
the command_ack back on the appropriate MAVLink instances instead of all
of them.
This commit filters outgoing command_ack messages, so they are only sent
on the MAVLink instances where the sysid/compid has been seen in the
past.
This means that a command_ack is likely still sent on multiple links for
a setup with redundant links.
This should also prevent command_acks from being blasted on Iridium links
when it's not required.
Signed-off-by: Julian Oes <julian@oes.ch>
On CubeOrange where no console is configured by default, starting
MAVLink shell just stalls, and doesn't work.
Also, logfile download has been reported not to work, and again, seems
to work with this change.
Signed-off-by: Julian Oes <julian@oes.ch>
- move EV yaw and EV position to new state machines
- EV yaw and EV pos now configured via EKF2_EV_CTRL (migrated from EKF2_AID_MASK)
- new EV position offset estimator to enable EV position while GPS position is active (no more EV pos delta fusion)
- yaw_align now strictly means north (no more rotate external vision aid mask)
- automatic switching between EV yaw, and yaw align north based on GPS quality
* GPS_RAW_INT: Only send no gps messages if gps has ever been present
* GPS2_RAW: Keep in sync with GPS_RAW_INT
Signed-off-by: Marcell Rausch <marcell@auterion.com>
In review it was requested to have a different name for
manual_control_setpoint.z because of the adjusted range.
I started to investigate what naming is most intuitive and found
that most people recognize the stick axes as roll, pitch, yaw, throttle.
It comes at no surprise because other autopilots
and APIs seem to share this convention.
While changing the code I realized that even within the code base
the axes are usually assigned to a variable with that name or
have comments next to the assignment clarifying the axes
using these names.
To be consistent with all other axes of stick input and avoid future
rescaling confusion.
Note: for the MAVLink message 69 MANUAL_CONTROL it's using the full range
according to the message specs now [-1000,1000].
The CameraFeedback module used only the vehicle attitude for the camera orientation so far. With this change, the gimbal_device_attitude_status is used to compute the global camera orientation when a gimbal is used.
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
Jaeyoung Lim