* NuttX cmake
* px4_macros:Pass the stringified predicate as second arg to static assert
CC_ASSERT mapes to the c++ static_assert or provides the same
funtionality for c via the other macros. The c++ static assert
takes 2 argumants the prdicate and a message. This fixes the
lacking second argument.
* Updated nuttx and apps submodule to upstream nuttx 7.21+==master
This is the latest uptake of upstream nuttx and apps.
* ROMFS generate with xxd instead of objcopy
* delete nuttx-patches
* NuttX update submodules to latest px4_nuttx-master
* fix nuttx apps and board dependency
* docker_run update to latest container 2017-08-29
* cmake ROMFS portable sed usage
* NuttX update submodules to latest px4_nuttx-master
was:<nuttx/arch.h> is:platform/cxxinitialize.h
Removed PX4 version:src/modules/systemlib/up_cxxinitialize.c
in favor of nuttx platform/gnu/gnu_cxxinitialize.c
This change plus the new FPGA RTL(version 0xC1 or higher) will make
use of the new I2C bus, this new bus will be shared between aerofc_adc
and ll40ls(if connected) and leaving the old bus just to IST8310.
The UART3 also have the I2C bus 2 functions so moving GPS to UART7 to
have one additional I2C.
To keep GPS working is also necessary update the FPGA RTL to version
0xC1 or higher.
This can help "unbrick" AeroFC when a bad firmware is loaded
and it keeps rebooting or it spinning in some loop.
No need to request to stay in booloader as it will stay
in bootloader because the pin is set.
- There's no I2C2, so remove it
- Fix alignments everywhere in board_config.h
- Clarify STM32 ADC (not available) and the ADC on the FGPA
- Fix format on some comments
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
The maximum number of missions was increased in almost 8 times in
recent commit: 9369262e63 navigator: allow more mission items.
As this board loads missions in RAM, now it don't have enough memory
to allocate causing dataman start to fail, so mark it as a memory
constrained system and reduce the number of maximum missions
supported.
We need to protect access to the param_values array. This is dynamically
allocated and resized (utarray_reserve() calls realloc). If some thread
was iterating the array while another was resizing the array, the first one
would iterate on a freed array, thus accessing invalid memory.
On NuttX this could lead to hardfaults in rare conditions.
Unfortunately we need to initialize the semaphore on startup, by calling
sem_init(). This adds a param_init() method called by every board/config
that uses the params (at least I think I've found all of them)
Changed the CONFIG_ARCH_BOARD_AEROFC_V1 in tap_esc.cpp to
TAP_ESC_NO_VERIFY_CONFIG to maintian the commitment to not
have CONFIG_ARCH_BOARD_xxxx ifdef litter in the PX4 code base.
TAP_ESC_NO_VERIFY_CONFIG will be removed (see todo) in
aerofc-v1/board_config.h
- Other channels are irrelevant since they aren't physically
connected. Avoid the I2C transaction to get invalid data
- Port the driver to use only one address, as it should be
- Minor changes here and there
- Add test() method to read the latest value - helpful during
debugging.
Measure the battery voltage of Aero RTF kit will be done by FPGA
and read by AeroFC using I2C bus.
The protocol is a little bit odd, it have different I2C slave
address for each "register", in future the FPGA RTL will
have a protocol more similar to other I2C sensors.
Also Aero RTF don't have a ADC line to measure current consumption.
boards define BOARD_NAME, so board_name() is not necessary. HW_ARCH was
just a wrapper around board_name().
This patch simplifies to having only one common method px4_board_name().
alessandro