Remove Gazebo Classic installation branches for Ubuntu 18.04 and 20.04.
The script now only supports Ubuntu 22.04 and 24.04 with Gazebo Harmonic.
Supported Ubuntu LTS versions going forward:
- Ubuntu 24.04 (primary, used in CI and release builds)
- Ubuntu 22.04 (secondary, still supported)
When Ubuntu 26.04 LTS releases we will bump to 26.04/24.04.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* Fixed an issue where if the GCC_VER_STR would not contain the right NUTTX_GCC_VERSION, the grep -c command would throw a failure, silently exiting the entire ubuntu.sh setup script
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
I don't think the PX4 setup script should decide whether a user is to
use ccache or not. Anecdotally, I've heard from some in the dev team
that they are not using it themselves, so I don't think there is a good
basis to push it onto others.
That being said, we can of course still use ccache as part of the CI
builds nevertheless.
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
- slightly faster skipping necessary copying (depending on system)
- allows debugging in place
- easier to work directly in NuttX following official documentation
- simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
- the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
- also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
- mavlink/mavlink is now directly included as a submodule instead of the generated mavlink/c_library_v2
- this also switches to mavlink development.xml by default
This fixes running the Ubuntu setup script in a Python virtual
environment. This was failing because pip doesn't allow the --user
option in virtual environments.
