* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Fix comments from review:
- Switch ssh link to https link in submodule
- Remove mc_nn_control from startup
* Add tflm to px4 with module
- Add TensorFlow Lite Micro(TFLM) as a library in px4
- Make a module that uses neural network inference for control, which uses TFLM for inference
- Make board config files for PX4 with neural module
* Added neural flight mode
* Add posibility to read of inference times
* Remove auto start
* Add logging from neural control module
* Fix automatic startup to only be when module is included
* Switch to flight mode registration
* Add docs
* Change min/max/coeff to actual parameters
* add figures to neural network docs
* Switch to e2e network
* Remove toolchain changes and replace with instructions in docs
* Get ready for merge after toolchain upgrade
* switch back to submodule
* Try to figure out cmake
* Get CI working with new toolchain
* Remove fork dependency
* Finalize PR
* fix toolchain inclusion
* Fix ctype_base.h include
* Cleanup includes for TFLM
* Remove redundant std
* Update FW module names in board files
* Fix docs
* Remove cstdlib copy
* Copy header from nuttx
* Prettier, markup, layout
* NeuralControl.msg - update uorb comments to current standard
* Add description to neural topic
* Fix typo
* Typo
* TFLM and Module utitlities
* Neural networks top level
* Update docs
* Add manual control
* Update docs
* Revert the manual control attempt
* Update docs/en/advanced/nn_module_utilities.md
* Add posibility to set trajectory setpoint with manual control
---------
Co-authored-by: Pedro Roque <padr@kth.se>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
* brought in the Vertiq Cpp API as a submodule. updated the serial rx handling so that we can parse out IQUART data packets
---------
Co-authored-by: Luca Scheuer <scheuer.luca@gmail.com>
This resets the USARTs' clock source selection to the default, in case
it has been changed by the bootloader.
This is required if booting from the ArduPilot bootloader which happens
to reset the clock selection to PLL.
Without this fix, UARTs (including the console) is garbled, so
presumably at an invalid baudrate.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
When flow control is used together with DMA, we need to add a pulldown
to CTS. Without it, it assumes flow control and gets stuck when
CTS is not connected.
Signed-off-by: Julian Oes <julian@oes.ch>
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Jacob Dahl