- this is required to support use cases where N numbers of batteries are connected
in parallel and detected by the system and N is not known beforehand
Signed-off-by: RomanBapst <bapstroman@gmail.com>
The length check for unknown packets did not include PACKET_SIZE_TYPE_SIZE
and CRC_SIZE, and hence working_index could overflow CRSF_MAX_PACKET_LEN,
triggering invalid memory access further down in QueueBuffer_PeekBuffer.
Also the working_segment_size was wrong for unknown packets.
Credits for finding this go to @Pwn9uin.
This allows to inject an updated ext_autostart folder with the name
ext_autostart_new, and then PX4 takes care of renaming it to
ext_autostart during bootup.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The sparse vector template requires to know which states are non-zero in
the observation jacobian. This complicates the modularity of the code
when the state vector or the derivation is changed.
The computation cost difference is almost negligible for this size.
For FW takeoffs we need to keep the course straight towards the first
waypoint, and not climb in loiter patterns first.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Current threshhold has no margins of errors with the set acceptance radius. Increase corridor radius by 5m.
Increase time to disarm for tailsitter test to pass.
Rverse mission needs check tracks test disabled since mavsdk does not really work with mission has reverse order.
mavsdk-test: added a vtol mission without a landing at the end (used for reversed RTL)
math_helpers: added function to compute local position from a raw mission item
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Dataman: Add write function to dataman cache.
RTL and mission have a new common base class mission_base. Both inherit from them and mission, RTL mission, and rtl reverse mission inherit from them and implement their desired functionalities. This simplifies the logic in mission as well as make the logic in rtl mission reverse and mission more readable.
Rtl mission reverse now functional again for VTOL flying back the mission and transitioning to MC at the home position.
Dataman cache has new write functionality to write to dataman while updating write item in its cache if necessary.
Dataman cache is now only updated when the respective module is active. Leads to a higher computation time once on activation, but decreases unnecessary cache updates when inactive.
This is required to support fixed pitch propeller helicopters that have
no collective but only cyclic pitch with two degrees of freedom and
hence only two servos.
The amount of thrust in the body z axis is then controlled using the
motor speed which makes particularly sense on coaxial helicopters
that need to control yaw with changing motor speeds already.
Events have a global, system-wide sequence number, which must be handled
atomically, (fetching and incrementing the sequence AND sending the event
to uORB must be atomic). Currently in FLAT mode, only one instance of this
sequence number exists, so it is OK to have it in px4_platform.
However, in PROTECTED mode px4_platform is instantiated both in kernel-
and user spaces, which makes two instances of this sequence number, which
causes problems in the mavlink event handling logic.
When mavlink receives and handles events, it expects that:
- The sequence numbers arrive in order (seq n is followed by n+1 etc)
- It increments by 1
- There is only one instance of the sequence number
In PROTECTED mode this is violated, as the kernel and user sequence
numbers run freely on their own. This patch fixes the issue by moving
the event backend to the kernel and by providing user access to it via
ioctl.
Even if there is some horizontal motion, a passing check should be
accepted as the terrain can be flat. However, the vehicle must not be
moving horizontally to invalidate the consistency as a change in terrain
can make the kinematic check temporarily fail.
A setpoint of type IDLE can be published by Navigator without a valid position,
and should be handled in the auto function in FW_POSCTRL_MODE_AUTO. If it wouldn't be
handled there the controller would switch to mode FW_POSCTRL_MODE_OTHER, in which case
no attitude setpoint is published and the lower controllers would be stuck with the
last published value (incl. thrust).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
but this time compared to
2fbb70d9ca
the minimum thrust is ramping to not produce a thrust jump.
The better long term solution will be to always have airmode but
with the effect limited to a magnitude of MPC_MANTHR_MIN.
high rates and (super) expo are necessary for
- acrobatic flying
- fpv
- racing
but they are not useful for:
- a typical vehicle's rate control tuning
- beginners
The defaults that I set in #8036 were put with the assumption Acro mode
is mainly used on racing drones for acrobatic manouvers but instead
users including me use it most of the time to tune any drone.
When tuning the rates are lowered and expo disabled.
My suggested strategy is to make the beginner friendly rates without
expo which are good for tuning the default and document more clearly
how this can be raised for acrobatic flying in documentation and later
on hopefully also directly in the ground station UI
on an Acro mode specific page.
* FW Positon Controller: set altitude_ref to 0 if not provided by GPS
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Positon Controller: set lat/lon reference to 0 if not provided in local_position
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
If no altitude setpoint is specified then takeoff to the default
altitude above the current global position, not above Home.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
c23b72dffe [BACKPORT] sched/semaphore: Remove restriction to use nxsem_trywait from ISR
fd47cd20a2 [BACKPORT] imxrt:Serial Preserve all but W1C bit in SR
c55f0fd3ac [BACKPORT] imxrt: lpspi dma invalidate cache after exchange
198c7caecb [BACKPORT] imxrt:lpi2c fix status handeling & race
cbd2e44c10 [BACKPORT] s32k3xx: lpspi dma invalidate cache after exchange
e71618d60e [BACKPORT] s32k3xx:lpi2c fix status handeling & race
6f59cc3659 [BACKPORT] s32k1xx:lpi2c fix status handeling & race
1e316d7e32 [BACKPORT] imxrt: flexcan use hpwork for receiving frames
67c1c59865 [BACKPORT] net/can can_readahead_timestamp always free iob
8be831a4ff [BACKPORT] imxrt: fix txdeadline add ecc/fd support
00a68b7668 [BACKPORT] fs/cromfs: Fix faulty DEBUGASSERT() check
d5cf545d6e [BACKPORT] S32K3XX EMAC MCAST support Fix compile warning when ioctl is not enabled
4265c830fa [BACKPORT] imxrt:edma {s|d}last needs to be total xfer size
24b4d44896 [BACKPORT] s32k3xx:edma {s|d}last needs to be total xfer size
eed0482f64 [BACKPORT] s32k1xx:edma {s|d}last needs to be total xfer size
36aab4146a [BACKPORT] kinetis:edma {s|d}last needs to be total xfer size
a0faf31f6f [BACKPORT] arch/stm32f7: fixes for pinmap
eb8255121d [BACKPORT] stm32h7:sdmmc It is not an error if no wait was needed
062044fe41 [BACKPORT] board nucleo-h743zi:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
e03f9d3917 [BACKPORT] board olimexino-stm32:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
4c3a467415 [BACKPORT] stm32l5:pinmap Add suffix to all pins and add legacy pinmap
153069ed40 [BACKPORT] stm32wb:pinmap Add suffix to all pins and add legacy pinmap
d84d737f89 [BACKPORT] stm32f0l0g0:stm32f0{3|5|7|9}x_pinmap & stm32g0_pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
5fc7071ac1 [BACKPORT] stm32l4:stm32l4x{3|4|5|6|r}xx_pinmap pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
20061c2aab [BACKPORT] stm32:stm32f10{0|2|3{c|r|v|z}|5{r|v}|7v}_pinmap refactor
4d1f83d484 [BACKPORT] stm32:stm32l15xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
2dfa3f2601 [BACKPORT] stm32:stm32g4xx{c|k|r|m|v|q} pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d206327809 [BACKPORT] stm32:stm32f3{0|3|7}xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
95e66ab508 [BACKPORT] stm32:stm32f20xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d2fd9178ad [BACKPORT] stm32:f4/f412 pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
a9df45166d [BACKPORT] stm32f7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
07dd2b424e [BACKPORT] stm32h7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
1e3065344f [BACKPORT] stm32u5:stm32u585xx_pinmap Fix typo
0a05365a90 [BACKPORT] stm32wl5:pinmap Fix typo
e3834138dc [BACKPORT] tools:Add STM32 Pin migration tool
df851a8768 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h also for stm32h7x7xx
d75dfcf1e9 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h
963f35f4fc [BACKPORT] {stm32,stm32f7,stm32h7,stm32l4,efm32}/otg: rasie an assertion if IN request is not possible to transfer
de2fcc6668 [BACKPORT] {stm32f7,stm32h7,stm32l4}/sdmmc: callback support requires HPWORK
6929144fc2 [BACKPORT] stm32h7/otgdev: FS transceiver must be enabled if OTGFS enabled
a2078afaea [BACKPORT] stm32h7/otg: add support for external ULPI
26e1246c86 [BACKPORT] stm32h7/rcc: OTGHS ULPI works only in VOS0
cd6daa185e [BACKPORT] stm32h7: update ULPI pins
c73c261ae3 [BACKPORT] arch/boards: fix stm32f411-mininum:nsh compilation failure after enabling IRQMONITOR
8078f134ef [BACKPORT] arch/stm32/stm32.h: do not include stm32_usbdev.h if not supported
60e884fa92 [BACKPORT] {stm32,stm32l4,stm32f0l0g0}/otg: move STM32_NENDPOINTS definitions to header files
dda297cb78 [BACKPORT] arch/arm/src/stm32/hardware: Fix register define
362b976b0e [BACKPORT] arch/arm/src/stm32/hardware: Add stm32g4 rcc apb1 timer enable compatibility
434fd71f2c [BACKPORT] {stm32/stm32l4/stm32f7/stm32h7/efm32}/otgdev: remove invalid use of the priv field for EP
2476d24e8c [BACKPORT] {stm32f7,stm32h7}/otg: fix compilation for USBDEV when USB_DEBUG=y
eb43c582ea [BACKPORT] drivers/mtd/ramtron: change nsectors size to uint32
20f61ff0d5 [BACKPORT] fs/littlefs: add full support for LittleFS block device cfg in Kconfig
60471fbf8c [BACKPORT] drivers/mtd: add Kconfig options for RAMTRON emulated page & sector size
- for FW the primary range finder usage is estimating the distance to
the ground (terrain estimate) to guide the landing approach and initiate flare
- increase EKF2_RNG_QLTY_T default 1->3 seconds
- force initialize takeoff airspeed setpoint at start of takeoff modes
- force set airspeed constraints if slewed value is out of bounds
- always slew airspeed setpoints as long as inside constraints
- move target airspeed setpoint calculation into mode specific logic regions (hand vs runway)
when we're in a takeoff situation, we only want to adapt the airspeed to
avoid accelerated stall due to load factor changes. Disable othre logic
like minimum ground speed, wind based adaption and airspeed slew rating.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
From looking at the history the BMM150 rotation was initially 0. Then,
this was changed to 6 when the intent was to only change it for Skynode.
A bit later, the rotation was changed back to 0, but only for Skynode.
This tells me that rotation 0 was correct for all 6X including Skynode
all along.
Signed-off-by: Julian Oes <julian@oes.ch>
- ekf2 heading first initializes to 0 degrees, then immediately resets to mag heading once a few samples are accumulated
- the yaw standard deviation check could be adjusted to exclude this brief (<1s) initial period
- on NuttX if the SD card was just cleared (quick format) it's possible for the newly created uninitialized dataman file to still have the previous compatibility key, which causes the initialization to be skipped
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
RomanBapst