split drivers/rc_input per protocol

On CubeOrange where no console is configured by default, starting
MAVLink shell just stalls, and doesn't work.

Also, logfile download has been reported not to work, and again, seems
to work with this change.

Signed-off-by: Julian Oes <julian@oes.ch>

.ci/Jenkinsfile-compile

@@ -65,6 +65,8 @@ pipeline {
                      "holybro_pix32v5_default",
                      "matek_gnss-m9n-f4_canbootloader",
                      "matek_gnss-m9n-f4_default",
+                     "matek_h743-mini_default",
+                     "matek_h743-slim_default",
                      "matek_h743_default",
                      "modalai_fc-v1_default",
                      "modalai_fc-v2_default",

.ci/Jenkinsfile-hardware

@@ -684,7 +684,7 @@ void checkStatus() {
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param save"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param status"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show SYS*"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params"'
 
   // status commands
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "cat /proc/fs/blocks"'
@@ -715,7 +715,7 @@ void checkStatus() {
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mavlink status" || true'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mount"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mtd status"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param show" || true'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param status"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "perf latency"'
@@ -767,13 +767,13 @@ void runTests() {
 
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "tests file" || true'
 
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump /fs/mtd_params"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mtd readtest"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump /fs/mtd_params"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mtd rwtest"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump /fs/mtd_params"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "mtd erase"'
-  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "param dump /fs/mtd_params"'
+  sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "bsondump /fs/mtd_params" || true' // expected to fail after erase
 
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sd_bench"'
   sh './Tools/HIL/run_nsh_cmd.py --device `find /dev/serial -name *usb-*` --cmd "sd_bench -v"'

.github/workflows/compile_nuttx.yml

@@ -40,6 +40,8 @@ jobs:
           holybro_pix32v5,
           matek_gnss-m9n-f4,
           matek_h743,
+          matek_h743-mini,
+          matek_h743-slim,
           modalai_fc-v1,
           modalai_fc-v2,
           mro_ctrl-zero-f7,

.github/workflows/sitl_tests.yml

@@ -16,7 +16,7 @@ jobs:
       matrix:
         config:
           - {model: "iris",          latitude:  "59.617693", longitude: "-151.145316", altitude:  "48", build_type: "RelWithDebInfo" } # Alaska
-          - {model: "standard_vtol", latitude: "-38.071235", longitude:  "145.281220", altitude:  "31", build_type: "AddressSanitizer" } # Australia
+          # - {model: "standard_vtol", latitude: "-38.071235", longitude:  "145.281220", altitude:  "31", build_type: "AddressSanitizer" } # Australia
           - {model: "tailsitter" ,   latitude:  "29.660316", longitude:  "-82.316658", altitude:  "30", build_type: "RelWithDebInfo" } # Florida
           - {model: "standard_vtol", latitude:  "47.397742", longitude:    "8.545594", altitude: "488", build_type: "Coverage" } # Zurich
 

.gitmodules

@@ -21,11 +21,11 @@
 [submodule "platforms/nuttx/NuttX/nuttx"]
 	path = platforms/nuttx/NuttX/nuttx
 	url = https://github.com/PX4/NuttX.git
-	branch = px4_firmware_nuttx-10.1.0+
+	branch = px4_firmware_nuttx-10.3.0+
 [submodule "platforms/nuttx/NuttX/apps"]
 	path = platforms/nuttx/NuttX/apps
 	url = https://github.com/PX4/NuttX-apps.git
-	branch = px4_firmware_nuttx-10.1.0+
+	branch = px4_firmware_nuttx-10.3.0+
 [submodule "Tools/flightgear_bridge"]
 	path = Tools/simulation/flightgear/flightgear_bridge
 	url = https://github.com/PX4/PX4-FlightGear-Bridge.git

.vscode/cmake-variants.yaml

@@ -211,11 +211,11 @@ CONFIG:
       buildType: MinSizeRel
       settings:
         CONFIG: holybro_durandal-v1_default
-    matek_h743_default:
-      short: matek_h743
+    matek_h743-slim_default:
+      short: matek_h743-slim
       buildType: MinSizeRel
       settings:
-        CONFIG: matek_h743_default
+        CONFIG: matek_h743-slim_default
     matek_gnss-m9n-f4_canbootloader:
       short: matek_gnss-m9n-f4_canbootloader
       buildType: MiniSizeRel

.vscode/settings.json

@@ -119,7 +119,9 @@
                 "utility": "cpp",
                 "valarray": "cpp",
                 "variant": "cpp",
-                "vector": "cpp"
+                "vector": "cpp",
+                "Jenkinsfile*": "groovy",
+                "*.sdf": "xml"
         },
         "search.exclude": {
                 "${workspaceFolder}/build": true
@@ -133,6 +135,5 @@
         "workbench.settings.enableNaturalLanguageSearch": false,
         "yaml.schemas": {
                 "${workspaceFolder}/validation/module_schema.yaml": "${workspaceFolder}/src/modules/*/module.yaml"
-        },
-        "cortex-debug.openocdPath": "${env:PICO_SDK_PATH}/../openocd/src/openocd"       // Added for rp2040
+        }
 }

CMakeLists.txt

@@ -1,6 +1,6 @@
 ############################################################################
 #
-# Copyright (c) 2017 - 2019 PX4 Development Team. All rights reserved.
+# Copyright (c) 2017 - 2022 PX4 Development Team. All rights reserved.
 #
 # Redistribution and use in source and binary forms, with or without
 # modification, are permitted provided that the following conditions
@@ -143,25 +143,17 @@ define_property(GLOBAL PROPERTY PX4_SRC_FILES
 # configuration
 #
 
-set(CONFIG "px4_sitl_default" CACHE STRING "desired configuration")
-
 include(px4_add_module)
 set(config_module_list)
 set(config_kernel_list)
 
 # Find Python
-# If using catkin, Python 2 is found since it points
-# to the Python libs installed with the ROS distro
-if (NOT CATKIN_DEVEL_PREFIX)
-	find_package(PythonInterp 3)
-	# We have a custom error message to tell users how to install python3.
-	if (NOT PYTHONINTERP_FOUND)
-		message(FATAL_ERROR "Python 3 not found. Please install Python 3:\n"
-			"    Ubuntu: sudo apt install python3 python3-dev python3-pip\n"
-			"    macOS: brew install python")
-	endif()
-else()
-	find_package(PythonInterp REQUIRED)
+find_package(PythonInterp 3)
+# We have a custom error message to tell users how to install python3.
+if(NOT PYTHONINTERP_FOUND)
+	message(FATAL_ERROR "Python 3 not found. Please install Python 3:\n"
+		"    Ubuntu: sudo apt install python3 python3-dev python3-pip\n"
+		"    macOS: brew install python")
 endif()
 
 option(PYTHON_COVERAGE "Python code coverage" OFF)
@@ -207,6 +199,11 @@ if(EXISTS "${PX4_SOURCE_DIR}/platforms/${PX4_PLATFORM}/cmake/init.cmake")
 	include(init)
 endif()
 
+#=============================================================================
+# project definition
+#
+project(px4 CXX C ASM)
+
 # CMake build type (Debug Release RelWithDebInfo MinSizeRel Coverage)
 if(NOT CMAKE_BUILD_TYPE)
 	if(${PX4_PLATFORM} STREQUAL "nuttx")
@@ -235,11 +232,6 @@ endif()
 set_property(CACHE CMAKE_BUILD_TYPE PROPERTY STRINGS "Debug;Release;RelWithDebInfo;MinSizeRel;Coverage;AddressSanitizer;UndefinedBehaviorSanitizer")
 message(STATUS "cmake build type: ${CMAKE_BUILD_TYPE}")
 
-#=============================================================================
-# project definition
-#
-project(px4 CXX C ASM)
-
 # Check if LTO option and check if toolchain supports it
 if(LTO)
     include(CheckIPOSupported)
@@ -256,15 +248,9 @@ set(CMAKE_C_STANDARD 11)
 set(CMAKE_C_STANDARD_REQUIRED ON)
 set(CMAKE_EXPORT_COMPILE_COMMANDS ON)
 
-# For the catkin build process, unset build of dynamically-linked binaries
-# and do not change CMAKE_RUNTIME_OUTPUT_DIRECTORY
-if (NOT CATKIN_DEVEL_PREFIX)
-	set(CMAKE_RUNTIME_OUTPUT_DIRECTORY ${PX4_BINARY_DIR})
-	set(CMAKE_RUNTIME_OUTPUT_DIRECTORY_DEBUG ${PX4_BINARY_DIR})
-	set(CMAKE_RUNTIME_OUTPUT_DIRECTORY_RELEASE ${PX4_BINARY_DIR})
-else()
-	SET(BUILD_SHARED_LIBS OFF)
-endif()
+set(CMAKE_RUNTIME_OUTPUT_DIRECTORY ${PX4_BINARY_DIR})
+set(CMAKE_RUNTIME_OUTPUT_DIRECTORY_DEBUG ${PX4_BINARY_DIR})
+set(CMAKE_RUNTIME_OUTPUT_DIRECTORY_RELEASE ${PX4_BINARY_DIR})
 
 #=============================================================================
 
@@ -309,21 +295,6 @@ endif()
 
 include(ccache)
 
-#=============================================================================
-# find programs and packages
-#
-
-# see if catkin was invoked to build this
-if (CATKIN_DEVEL_PREFIX)
-	message(STATUS "catkin ENABLED")
-	find_package(catkin REQUIRED)
-	if (catkin_FOUND)
-		catkin_package()
-	else()
-		message(FATAL_ERROR "catkin not found")
-	endif()
-endif()
-
 #=============================================================================
 # get chip and chip manufacturer
 #
@@ -450,10 +421,10 @@ add_subdirectory(src/lib/metadata EXCLUDE_FROM_ALL)
 add_subdirectory(src/lib/parameters EXCLUDE_FROM_ALL)
 
 if(${PX4_PLATFORM} STREQUAL "nuttx" AND NOT CONFIG_BUILD_FLAT)
-target_link_libraries(parameters_interface INTERFACE usr_parameters)
-target_link_libraries(kernel_parameters_interface INTERFACE parameters)
+	target_link_libraries(parameters_interface INTERFACE usr_parameters)
+	target_link_libraries(kernel_parameters_interface INTERFACE parameters)
 else()
-target_link_libraries(parameters_interface INTERFACE parameters)
+	target_link_libraries(parameters_interface INTERFACE parameters)
 endif()
 
 # firmware added last to generate the builtin for included modules
@@ -486,17 +457,13 @@ include(doxygen)
 include(metadata)
 include(package)
 
-# print size
-add_custom_target(size
-	COMMAND size $<TARGET_FILE:px4>
-	DEPENDS px4
-	WORKING_DIRECTORY ${PX4_BINARY_DIR}
-	USES_TERMINAL
-	)
-
 # install python requirements using configured python
 add_custom_target(install_python_requirements
 	COMMAND ${PYTHON_EXECUTABLE} -m pip install --requirement ${PX4_SOURCE_DIR}/Tools/setup/requirements.txt
 	DEPENDS ${PX4_SOURCE_DIR}/Tools/setup/requirements.txt
 	USES_TERMINAL
 )
+
+if(EXISTS "${PX4_SOURCE_DIR}/platforms/${PX4_PLATFORM}/cmake/finalize.cmake")
+	include(finalize)
+endif()

Kconfig

@@ -17,6 +17,8 @@ menu "Toolchain"
             bool "posix"
         config PLATFORM_QURT
             bool "qurt"
+        config PLATFORM_ROS2
+            bool "ros2"
     endchoice
 
     config BOARD_PLATFORM
@@ -24,6 +26,7 @@ menu "Toolchain"
         default "nuttx" if PLATFORM_NUTTX
         default "posix" if PLATFORM_POSIX
         default "qurt" if PLATFORM_QURT
+        default "ros2" if PLATFORM_ROS2
 
     config BOARD_LOCKSTEP
         bool "Force enable lockstep"
@@ -37,8 +40,8 @@ menu "Toolchain"
         help
             forces nolockstep behaviour, despite REPLAY env variable
 
-    config BOARD_LINUX
-        bool "Linux OS"
+    config BOARD_LINUX_TARGET
+        bool "Linux OS Target"
         depends on PLATFORM_POSIX
         help
             Board Platform is running the Linux operating system

Makefile

@@ -328,7 +328,7 @@ jlink-nuttx:
 	$(CC) -shared -fPIC platforms/nuttx/NuttX/nuttx/tools/jlink-nuttx.c -o Tools/jlink-nuttx.so
 
 
-bootloaders_update: ark_fmu-v6x_bootloader cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader holybro_kakuteh7_bootloader matek_h743_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6c_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
+bootloaders_update: ark_fmu-v6x_bootloader cuav_nora_bootloader cuav_x7pro_bootloader cubepilot_cubeorange_bootloader holybro_durandal-v1_bootloader holybro_kakuteh7_bootloader matek_h743_bootloader matek_h743-mini_bootloader matek_h743-slim_bootloader modalai_fc-v2_bootloader mro_ctrl-zero-classic_bootloader mro_ctrl-zero-h7_bootloader mro_ctrl-zero-h7-oem_bootloader mro_pixracerpro_bootloader px4_fmu-v6c_bootloader px4_fmu-v6u_bootloader px4_fmu-v6x_bootloader
 	git status
 
 .PHONY: coverity_scan

ROMFS/cannode/init.d/rcS

@@ -31,6 +31,11 @@ then
 	set PARAM_FILE /dev/eeeprom0
 fi
 
+if mft query -q -k MTD -s MTD_PARAMETERS -v /mnt/qspi/params
+then
+	set PARAM_FILE /mnt/qspi/params
+fi
+
 #
 # Load parameters.
 #

ROMFS/px4fmu_common/init.d-posix/airframes/1037_believer

@@ -38,8 +38,6 @@ param set-default MIS_TAKEOFF_ALT 30
 param set-default NAV_ACC_RAD 15
 param set-default NAV_DLL_ACT 2
 
-param set-default FW_USE_NPFG 1
-
 param set-default RWTO_TKOFF 1
 
 param set-default CA_AIRFRAME 1

ROMFS/px4fmu_common/init.d-posix/px4-rc.mavlink

@@ -3,7 +3,7 @@
 
 udp_offboard_port_local=$((14580+px4_instance))
 udp_offboard_port_remote=$((14540+px4_instance))
-[ $px4_instance -gt 9 ] && udp_offboard_port_remote=14549 # use the same ports for more than 10 instances to avoid port overlaps
+[ "$px4_instance" -gt 9 ] && udp_offboard_port_remote=14549 # use the same ports for more than 10 instances to avoid port overlaps
 udp_onboard_payload_port_local=$((14280+px4_instance))
 udp_onboard_payload_port_remote=$((14030+px4_instance))
 udp_onboard_gimbal_port_local=$((13030+px4_instance))

ROMFS/px4fmu_common/init.d-posix/px4-rc.simulator

@@ -13,108 +13,97 @@ if [ "$PX4_SIMULATOR" = "sihsim" ] || [ "$(param show -q SYS_AUTOSTART)" -eq "0"
 		sensor_mag_sim start
 
 	else
-		echo "ERROR  [init] simulator_sih failed to start"
+		echo "ERROR [init] simulator_sih failed to start"
 		exit 1
 	fi
 
 elif [ "$PX4_SIMULATOR" = "gz" ]; then
 
 	# source generated gazebo_env.sh for IGN_GAZEBO_RESOURCE_PATH
-	if [ -f gazebo_env.sh ]; then
+	if [ -f ./gazebo_env.sh ]; then
 		. ./gazebo_env.sh
+
 	elif [ -f ../gazebo_env.sh ]; then
 		. ../gazebo_env.sh
 	fi
 
-# shellcheck disable=SC2236
-	if [ ! -z $PX4_GZ_VERBOSE ]; then
-		if [ "$PX4_GZ_VERBOSE" -le "4" ] && [ "$PX4_GZ_VERBOSE" -ge "1" ]; then
-			gz_verbose=$PX4_GZ_VERBOSE
-		else
-			gz_verbose=4
-			echo "WARN  [init] PX4_GZ_VERBOSE was passed: $PX4_GZ_VERBOSE, not in range [1,4], defaulting to: $gz_verbose."
-		fi
-		echo "INFO  [init] PX4_GZ_VERBOSE set to $gz_verbose."
-	else
-		gz_verbose=1
-		echo "INFO  [init] PX4_GZ_VERBOSE not explicitly set, defaulting to: $gz_verbose."
-	fi
+	gz_command="ign" # "ign" before garden
+	gz_sub_command="gazebo" # "gazebo" before garden
 
-	gz_world=$( ign topic -l | grep -m 1 -e "/world/.*/clock" | sed 's/\/world\///g; s/\/clock//g' )
-	
-	gz_version_major=$( ign gazebo --versions | sed 's/\..*//g' )
-	gz_version_minor=$( ign gazebo --versions | sed 's/'"${gz_version_major}"\.'//; s/\..*//g' )
-	gz_version_point=$( ign gazebo --versions | sed 's/'"${gz_version_major}"\.'//; s/'"${gz_version_minor}"\.'//')
+	# look for running ${gz_command} gazebo world
+	gz_world=$( ${gz_command} topic -l | grep -m 1 -e "/world/.*/clock" | sed 's/\/world\///g; s/\/clock//g' )
 
-	if [ "$gz_version_major" -gt "6" ] || { [ "$gz_version_major" -eq "6" ] && [ "$gz_version_minor" -gt "12" ]; } || { [ "$gz_version_major" -eq "6" ] && [ "$gz_version_minor" -eq "12" ] && [ "$gz_version_point" -gt "0" ]; }; then
-		echo "INFO  [init] using latest version of MultiCopterMotor plugin."
-	else
-		echo "WARN  [init] using older version of MultiCopterMotor plugin, please update to latest gazebo > 6.12.0."
-		if [ "$PX4_SIM_MODEL" = "x500" ]; then
-			PX4_SIM_MODEL="x500-Legacy"
-			echo "WARN  [init] setting PX4_SIM_MODEL -> $PX4_SIM_MODEL from x500 till gazebo > 6.12.0"
-		fi
-	fi
+	# shellcheck disable=SC2153
+	if [ -z "${gz_world}" ] && [ -n "${PX4_GZ_WORLDS}" ] && [ -n "${PX4_GZ_WORLD}" ]; then
 
-	if [ -z $gz_world ]; then
+		echo "INFO  [init] starting gazebo with world: ${PX4_GZ_WORLDS}/${PX4_GZ_WORLD}.sdf"
 
-		# starting ign gazebo with ${PX4_GZ_WORLD} world
-		echo "INFO  [init] starting ign gazebo"
-# shellcheck disable=SC2153
-		ign gazebo --verbose=$gz_verbose -r -s "${PX4_GZ_WORLDS}/${PX4_GZ_WORLD}.sdf" &
+		${gz_command} ${gz_sub_command} --verbose=1 -r -s "${PX4_GZ_WORLDS}/${PX4_GZ_WORLD}.sdf" &
 
-		if [ -z $HEADLESS ]; then
+		if [ -z "${HEADLESS}" ]; then
 			# HEADLESS not set, starting ign gazebo gui
-			ign gazebo -g &
+			${gz_command} gazebo -g &
 		fi
+
 	else
-		echo "INFO  [init] ign gazebo already running world: $gz_world"
-		PX4_GZ_WORLD=$gz_world
+		echo "INFO  [init] gazebo already running world: ${gz_world}"
+		PX4_GZ_WORLD=${gz_world}
 	fi
 
-# shellcheck disable=SC2236
-	if [ ! -z $PX4_GZ_MODEL ] && [ -z $PX4_GZ_MODEL_NAME ]; then
+	# start gz_bridge
+	if [ -n "${PX4_GZ_MODEL}" ] && [ -z "${PX4_GZ_MODEL_NAME}" ]; then
+		# model specified, gz_bridge will spawn model
 
-# shellcheck disable=SC2236
-		if [ ! -z $PX4_GZ_MODEL_POSE ]; then
+		if [ -n "${PX4_GZ_MODEL_POSE}" ]; then
 			# Clean potential input line formatting.
-			model_pose="$( echo ${PX4_GZ_MODEL_POSE} | sed -e 's/^[ \t]*//; s/[ \t]*$//; s/,/ /g; s/  / /g; s/ /,/g' )"
+			model_pose="$( echo "${PX4_GZ_MODEL_POSE}" | sed -e 's/^[ \t]*//; s/[ \t]*$//; s/,/ /g; s/  / /g; s/ /,/g' )"
 			echo "INFO  [init] PX4_GZ_MODEL_POSE set, spawning at: ${model_pose}"
+
 		else
 			echo "WARN  [init] PX4_GZ_MODEL_POSE not set, spawning at origin."
 			model_pose="0,0,0,0,0,0"
 		fi
+
 		# start gz bridge with pose arg.
-		if gz_bridge start -p "${model_pose}"  -m "${PX4_GZ_MODEL}" -w "${PX4_GZ_WORLD}" -i "${px4_instance}"; then
+		if gz_bridge start -p "${model_pose}" -m "${PX4_GZ_MODEL}" -w "${PX4_GZ_WORLD}" -i "${px4_instance}"; then
 			sensor_baro_sim start
 			sensor_gps_sim start
 			sensor_mag_sim start
+
 		else
-			echo "ERROR  [init] ign gazebo failed to start"
+			echo "ERROR [init] gazebo failed to start"
 			exit 1
 		fi
-	elif [ ! -z $PX4_GZ_MODEL_NAME ] && [ -z $PX4_GZ_MODEL ]; then
+
+	elif [ -n "${PX4_GZ_MODEL_NAME}" ] && [ -z "${PX4_GZ_MODEL}" ]; then
+		# model name specificed, gz_bridge will attach to existing model
+
 		if gz_bridge start -n "${PX4_GZ_MODEL_NAME}" -w "${PX4_GZ_WORLD}"; then
 			sensor_baro_sim start
 			sensor_gps_sim start
 			sensor_mag_sim start
+
 		else
-			echo "ERROR  [init] ign gazebo failed to start"
+			echo "ERROR [init] gazebo failed to start"
 			exit 1
 		fi
-	elif [ ! -z $PX4_SIM_MODEL ] && [ -z $PX4_GZ_MODEL_NAME ] && [ -z $PX4_GZ_MODEL ]; then
+
+	elif [ -n "${PX4_SIM_MODEL}" ] && [ -z "${PX4_GZ_MODEL_NAME}" ] && [ -z "${PX4_GZ_MODEL}" ]; then
+
 		echo "WARN  [init] PX4_GZ_MODEL_NAME or PX4_GZ_MODEL not set using PX4_SIM_MODEL."
+
 		if gz_bridge start -m "${PX4_SIM_MODEL}" -w "${PX4_GZ_WORLD}" -i "${px4_instance}"; then
 			sensor_baro_sim start
 			sensor_gps_sim start
 			sensor_mag_sim start
+
 		else
-			echo "ERROR  [init] ign gazebo failed to start"
+			echo "ERROR [init] gazebo failed to start"
 			exit 1
 		fi
 
 	else
-		echo "ERROR  [init] failed to pass only PX4_GZ_MODEL_NAME or PX4_GZ_MODEL"
+		echo "ERROR [init] failed to pass only PX4_GZ_MODEL_NAME or PX4_GZ_MODEL"
 		exit 1
 	fi
 
@@ -131,13 +120,13 @@ else
 			echo "PX4 SIM HOST: localhost"
 			simulator_mavlink start -c $simulator_tcp_port
 		else
-			echo "PX4 SIM HOST: $PX4_SIM_HOST_ADDR"
-			simulator_mavlink start -t $PX4_SIM_HOST_ADDR $simulator_tcp_port
+			echo "PX4 SIM HOST: ${PX4_SIM_HOST_ADDR}"
+			simulator_mavlink start -t "${PX4_SIM_HOST_ADDR}" "${simulator_tcp_port}"
 		fi
 
 	else
-		echo "PX4 SIM HOST: $PX4_SIM_HOSTNAME"
-		simulator_mavlink start -h $PX4_SIM_HOSTNAME $simulator_tcp_port
+		echo "PX4 SIM HOST: ${PX4_SIM_HOSTNAME}"
+		simulator_mavlink start -h "${PX4_SIM_HOSTNAME}" "${simulator_tcp_port}"
 	fi
 
 fi

ROMFS/px4fmu_common/init.d-posix/rcS

@@ -74,7 +74,7 @@ if [ -f $PARAM_FILE ]; then
 	then
 		echo "ERROR [init] param import failed"
 
-		param dump $PARAM_FILE
+		bsondump $PARAM_FILE
 
 		# try to make a backup copy
 		cp $PARAM_FILE param_import_fail.bson
@@ -85,7 +85,7 @@ if [ -f $PARAM_FILE ]; then
 			echo "[init] importing from parameter backup"
 
 			# dump current backup file contents for comparison
-			param dump $PARAM_BACKUP_FILE
+			bsondump $PARAM_BACKUP_FILE
 
 			param import $PARAM_BACKUP_FILE
 
@@ -142,7 +142,9 @@ then
 	param set CAL_GYRO2_ID 1311004 # 1311004: DRV_IMU_DEVTYPE_SIM, BUS: 3, ADDR: 1, TYPE: SIMULATION
 
 	param set CAL_MAG0_ID 197388
+	param set CAL_MAG0_PRIO 50
 	param set CAL_MAG1_ID 197644
+	param set CAL_MAG1_PRIO 50
 
 	param set SENS_BOARD_X_OFF 0.000001
 	param set SENS_DPRES_OFF 0.001
@@ -260,7 +262,19 @@ fi
 navigator start
 
 # Try to start the microdds_client with UDP transport if module exists
-microdds_client start -t udp -p 8888
+microdds_ns=""
+if [ "$px4_instance" -ne "0" ]
+then
+	# Assign new xrce dds key based on instance number and set default namespace
+	param set XRCE_DDS_KEY ${px4_instance}
+	microdds_ns="-n px4_$px4_instance"
+fi
+if [ -n "$PX4_MICRODDS_NS" ]
+then
+	# Override namespace if environment variable is defined
+	microdds_ns="-n $PX4_MICRODDS_NS"
+fi
+microdds_client start -t udp -p 8888 $microdds_ns
 
 if param greater -s MNT_MODE_IN -1
 then

ROMFS/px4fmu_common/init.d/rcS

@@ -29,7 +29,6 @@ set LOGGER_ARGS ""
 set LOGGER_BUF 8
 set PARAM_FILE ""
 set PARAM_BACKUP_FILE ""
-set RC_INPUT_ARGS ""
 set SDCARD_AVAILABLE no
 set SDCARD_EXT_PATH /fs/microsd/ext_autostart
 set SDCARD_FORMAT no
@@ -130,7 +129,7 @@ else
 		echo "ERROR [init] param import failed"
 		set STARTUP_TUNE 2 # tune 2 = ERROR_TUNE
 
-		param dump $PARAM_FILE
+		bsondump $PARAM_FILE
 
 		if [ -d "/fs/microsd" ]
 		then
@@ -143,7 +142,7 @@ else
 				echo "[init] importing from parameter backup"
 
 				# dump current backup file contents for comparison
-				param dump $PARAM_BACKUP_FILE
+				bsondump $PARAM_BACKUP_FILE
 
 				param import $PARAM_BACKUP_FILE
 
@@ -411,8 +410,10 @@ else
 	#
 	. ${R}etc/init.d/rc.serial
 
-	# Must be started after the serial config is read
-	rc_input start $RC_INPUT_ARGS
+	if param compare -s RC_PPM_EN 1
+	then
+		ppm_in start
+	fi
 
 	#
 	# Play the startup tune (if not disabled or there is an error)
@@ -544,7 +545,6 @@ unset LOGGER_ARGS
 unset LOGGER_BUF
 unset PARAM_FILE
 unset PARAM_BACKUP_FILE
-unset RC_INPUT_ARGS
 unset SDCARD_AVAILABLE
 unset SDCARD_EXT_PATH
 unset SDCARD_FORMAT

Tools/HIL/test_airframes.sh

@@ -43,13 +43,13 @@ do
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param reset SYS_HITL'
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param status'
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param save'
-	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param dump'
+	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'bsondump /fs/mtd_params'
 
 	${DIR}/reboot.py --device ${SERIAL_DEVICE}
 
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param status'
-	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param dump /fs/mtd_params' || true
-	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'param dump /fs/microsd/parameters_backup.bson' || true
+	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'bsondump /fs/mtd_params' || true
+	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'bsondump /fs/microsd/parameters_backup.bson' || true
 
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'ps'
 	${DIR}/run_nsh_cmd.py --device ${SERIAL_DEVICE} --cmd 'work_queue status'

Tools/generate_board_targets_json.py

@@ -28,7 +28,7 @@ args = parser.parse_args()
 verbose = args.verbose
 
 build_configs = []
-excluded_boards = ['modalai_voxl2']  # TODO: fix and enable
+excluded_boards = ['modalai_voxl2', 'px4_ros2']  # TODO: fix and enable
 excluded_manufacturers = ['atlflight']
 excluded_platforms = ['qurt']
 excluded_labels = [

Tools/serial/generate_config.py

@@ -136,9 +136,9 @@ serial_ports = {
         "default_baudrate": 1, # set default to an unusable value to detect that this serial port has not been configured
         },
 
-    # Pixhawk Payload Bus
-    "PPB": {
-        "label": "Pixhawk Payload Bus",
+    # EXT2
+    "EXT2": {
+        "label": "EXT2",
         "index": 401,
         "default_baudrate": 57600,
         },

Tools/simulation/gazebo/sitl_gazebo

@@ -1 +1 @@
-Subproject commit b38e701ec4230a6105ace872447c0f63bc181d41
+Subproject commit 049b667d5e86fa71bd47c41dd10e911a0e2681b0

Tools/simulation/gz/models/x500-Legacy/model.config

@@ -1,11 +0,0 @@
-<?xml version="1.0"?>
-<model>
-  <name>x500-Legacy</name>
-  <version>1.0</version>
-  <sdf version="1.9">model.sdf</sdf>
-  <author>
-    <name>Benjamin Perseghetti</name>
-    <email>bperseghetti@rudislabs.com</email>
-  </author>
-  <description>Model of the NXP HoverGames Drone development kit (KIT-HGDRONEK66). The PX4 software compatible kit provides mechanical, RC remote and other components needed to evaluate the RDDRONE-FMUK66 reference design. The FMU includes 100Base-T1 Automotive Ethernet, dual CAN transceivers, as well as SE050 secure element, and works with add on boards NavQPlus, MR-T1ETH8, MR-T1ADAPT, and CAN-nodes such as UCANS32K1SIC.  Kit may be used with, and contains the components needed for the HoverGames.com coding challenges.</description>
-</model>

Tools/simulation/gz/models/x500-Legacy/model.sdf

@@ -1,76 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<sdf version='1.9'>
-  <model name='x500-Legacy'>
-    <include merge='true'>
-      <uri>model://x500-NoPlugin</uri>
-    </include>
-    <plugin filename="ignition-gazebo-multicopter-motor-model-system" name="ignition::gazebo::systems::MulticopterMotorModel">
-      <robotNamespace>/x500-Legacy_0</robotNamespace>
-      <jointName>rotor_0_joint</jointName>
-      <linkName>rotor_0</linkName>
-      <turningDirection>ccw</turningDirection>
-      <timeConstantUp>0.0125</timeConstantUp>
-      <timeConstantDown>0.025</timeConstantDown>
-      <maxRotVelocity>1000.0</maxRotVelocity>
-      <motorConstant>8.54858e-06</motorConstant>
-      <momentConstant>0.016</momentConstant>
-      <commandSubTopic>command/motor_speed</commandSubTopic>
-      <motorNumber>0</motorNumber>
-      <rotorDragCoefficient>8.06428e-05</rotorDragCoefficient>
-      <rollingMomentCoefficient>1e-06</rollingMomentCoefficient>
-      <rotorVelocitySlowdownSim>10</rotorVelocitySlowdownSim>
-      <motorType>velocity</motorType>
-    </plugin>
-    <plugin filename="ignition-gazebo-multicopter-motor-model-system" name="ignition::gazebo::systems::MulticopterMotorModel">
-      <robotNamespace>/x500-Legacy_0</robotNamespace>
-      <jointName>rotor_1_joint</jointName>
-      <linkName>rotor_1</linkName>
-      <turningDirection>ccw</turningDirection>
-      <timeConstantUp>0.0125</timeConstantUp>
-      <timeConstantDown>0.025</timeConstantDown>
-      <maxRotVelocity>1000.0</maxRotVelocity>
-      <motorConstant>8.54858e-06</motorConstant>
-      <momentConstant>0.016</momentConstant>
-      <commandSubTopic>command/motor_speed</commandSubTopic>
-      <motorNumber>1</motorNumber>
-      <rotorDragCoefficient>8.06428e-05</rotorDragCoefficient>
-      <rollingMomentCoefficient>1e-06</rollingMomentCoefficient>
-      <rotorVelocitySlowdownSim>10</rotorVelocitySlowdownSim>
-      <motorType>velocity</motorType>
-    </plugin>
-    <plugin filename="ignition-gazebo-multicopter-motor-model-system" name="ignition::gazebo::systems::MulticopterMotorModel">
-      <robotNamespace>/x500-Legacy_0</robotNamespace>
-      <jointName>rotor_2_joint</jointName>
-      <linkName>rotor_2</linkName>
-      <turningDirection>cw</turningDirection>
-      <timeConstantUp>0.0125</timeConstantUp>
-      <timeConstantDown>0.025</timeConstantDown>
-      <maxRotVelocity>1000.0</maxRotVelocity>
-      <motorConstant>8.54858e-06</motorConstant>
-      <momentConstant>0.016</momentConstant>
-      <commandSubTopic>command/motor_speed</commandSubTopic>
-      <motorNumber>2</motorNumber>
-      <rotorDragCoefficient>8.06428e-05</rotorDragCoefficient>
-      <rollingMomentCoefficient>1e-06</rollingMomentCoefficient>
-      <rotorVelocitySlowdownSim>10</rotorVelocitySlowdownSim>
-      <motorType>velocity</motorType>
-    </plugin>
-    <plugin filename="ignition-gazebo-multicopter-motor-model-system" name="ignition::gazebo::systems::MulticopterMotorModel">
-      <robotNamespace>/x500-Legacy_0</robotNamespace>
-      <jointName>rotor_3_joint</jointName>
-      <linkName>rotor_3</linkName>
-      <turningDirection>cw</turningDirection>
-      <timeConstantUp>0.0125</timeConstantUp>
-      <timeConstantDown>0.025</timeConstantDown>
-      <maxRotVelocity>1000.0</maxRotVelocity>
-      <motorConstant>8.54858e-06</motorConstant>
-      <momentConstant>0.016</momentConstant>
-      <commandSubTopic>command/motor_speed</commandSubTopic>
-      <motorNumber>3</motorNumber>
-      <rotorDragCoefficient>8.06428e-05</rotorDragCoefficient>
-      <rollingMomentCoefficient>1e-06</rollingMomentCoefficient>
-      <rotorVelocitySlowdownSim>10</rotorVelocitySlowdownSim>
-      <motorType>velocity</motorType>
-    </plugin>
-  </model>
-</sdf>

Tools/simulation/jmavsim/jmavsim_run.sh

@@ -73,4 +73,5 @@ fi
 ant create_run_jar copy_res
 cd out/production
 
-java -XX:GCTimeRatio=20 -Djava.ext.dirs= -jar jmavsim_run.jar $device $extra_args
+java --add-exports java.base/java.lang=ALL-UNNAMED --add-exports java.desktop/sun.awt=ALL-UNNAMED --add-exports java.desktop/sun.java2d=ALL-UNNAMED \
+	-XX:GCTimeRatio=20 -Djava.ext.dirs= -jar jmavsim_run.jar $device $extra_args

boards/airmind/mindpx-v2/default.px4board

@@ -4,6 +4,7 @@ CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS3"
 CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS2"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS0"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_COMMON_BAROMETERS=y
@@ -28,7 +29,8 @@ CONFIG_DRIVERS_PCA9685_PWM_OUT=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_INPUT=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_DRIVERS_ROBOCLAW=y
 CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
@@ -79,8 +81,9 @@ CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
 CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y
 CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y

boards/ark/fmu-v6x/default.px4board

@@ -7,9 +7,9 @@ CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS6"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
 CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS5"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP388=y
-CONFIG_DRIVERS_BAROMETER_MS5611=y
 CONFIG_DRIVERS_BATT_SMBUS=y
 CONFIG_DRIVERS_CAMERA_CAPTURE=y
 CONFIG_DRIVERS_CAMERA_TRIGGER=y
@@ -28,7 +28,8 @@ CONFIG_DRIVERS_POWER_MONITOR_INA228=y
 CONFIG_DRIVERS_POWER_MONITOR_INA238=y
 CONFIG_DRIVERS_PWM_OUT=y
 CONFIG_DRIVERS_PX4IO=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_DRIVERS_SAFETY_BUTTON=y
 CONFIG_DRIVERS_TONE_ALARM=y
 CONFIG_DRIVERS_UAVCAN=y
@@ -66,10 +67,10 @@ CONFIG_MODULES_ROVER_POS_CONTROL=y
 CONFIG_MODULES_SENSORS=y
 CONFIG_MODULES_SIMULATION_PWM_OUT_SIM=y
 CONFIG_MODULES_SIMULATION_SIMULATOR_SIH=y
-CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
 CONFIG_SYSTEMCMDS_I2CDETECT=y

boards/ark/fmu-v6x/init/rc.board_defaults

@@ -16,6 +16,13 @@ param set-default SENS_EN_INA238 0
 param set-default SENS_EN_INA228 0
 param set-default SENS_EN_INA226 1
 
+param set-default SENS_EN_THERMAL 1
+param set-default SENS_TEMP_ID 2818058
+param set-default SENS_IMU_TEMP 10.0
+#param set-default SENS_IMU_TEMP_FF 0.0
+#param set-default SENS_IMU_TEMP_I 0.025
+#param set-default SENS_IMU_TEMP_P 1.0
+
 if ver hwtypecmp ARKV6X001000 ARKV6X001001 ARKV6X001002 ARKV6X001003 ARKV6X001004 ARKV6X001005 ARKV6X001006 ARKV6X001007
 then
 	param set-default SYS_USE_IO 0

boards/ark/fmu-v6x/init/rc.board_sensors

@@ -8,6 +8,7 @@ if ver hwtypecmp ARKV6X005000 ARKV6X005001 ARKV6X005002 ARKV6X005003 ARKV6X00500
 then
 	set HAVE_PM2 no
 fi
+
 if param compare -s ADC_ADS1115_EN 1
 then
 	ads1115 start -X
@@ -15,7 +16,6 @@ else
 	board_adc start
 fi
 
-
 if param compare SENS_EN_INA226 1
 then
 	# Start Digital power monitors
@@ -56,16 +56,10 @@ icm42688p -R 9 -s -b 2 start
 # Internal SPI bus ICM42688p
 icm42688p -R 6 -s -b 3 start
 
-# Internal magnetometer on I2c
+# Internal magnetometer on I2C
 bmm150 -I start
 
-# External compass on GPS1/I2C1 (the 3rd external bus): standard Holybro Pixhawk 4 or CUAV V5 GPS/compass puck (with lights, safety button, and buzzer)
-ist8310 -X -b 1 -R 10 start
-
-# Possible internal Baro
+# Internal Baro on I2C
 bmp388 -I start
 
-# Baro on I2C3
-ms5611 -X start
-
 unset HAVE_PM2

boards/ark/fmu-v6x/nuttx-config/nsh/defconfig

@@ -159,6 +159,7 @@ CONFIG_NET_BROADCAST=y
 CONFIG_NET_ETH_PKTSIZE=1518
 CONFIG_NET_ICMP=y
 CONFIG_NET_ICMP_SOCKET=y
+CONFIG_NET_NACTIVESOCKETS=16
 CONFIG_NET_SOLINGER=y
 CONFIG_NET_TCP=y
 CONFIG_NET_TCPBACKLOG=y

boards/ark/fmu-v6x/src/board_config.h

@@ -323,7 +323,6 @@
 #define GPIO_PPM_IN             /* PI5 T8C1 */ GPIO_TIM8_CH1IN_2
 
 /* RC Serial port */
-
 #define RC_SERIAL_PORT                     "/dev/ttyS5"
 
 /* Input Capture Channels. */

boards/atl/mantis-edu/src/board_config.h

@@ -145,10 +145,6 @@
 #define HRT_TIMER               8  /* use timer8 for the HRT */
 #define HRT_TIMER_CHANNEL       3  /* use capture/compare channel 3 */
 
-/* RC Serial port */
-#define RC_SERIAL_PORT                     "/dev/ttyS5"
-#define RC_SERIAL_SINGLEWIRE
-
 /* power on/off */
 #define MS_PWR_BUTTON_DOWN 750
 #define KEY_AD_GPIO    (GPIO_INPUT|GPIO_PULLUP|GPIO_EXTI|GPIO_PORTC|GPIO_PIN4)

boards/av/x-v1/default.px4board

@@ -6,6 +6,7 @@ CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS0"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_COMMON_BAROMETERS=y
@@ -22,14 +23,12 @@ CONFIG_DRIVERS_IRLOCK=y
 CONFIG_COMMON_LIGHT=y
 CONFIG_COMMON_MAGNETOMETER=y
 CONFIG_COMMON_OPTICAL_FLOW=y
-CONFIG_DRIVERS_OSD=y
 CONFIG_DRIVERS_PCA9685=y
 CONFIG_DRIVERS_PCA9685_PWM_OUT=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
 CONFIG_DRIVERS_ROBOCLAW=y
-CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_COMMON_TELEMETRY=y
 CONFIG_DRIVERS_UAVCAN=y
@@ -38,6 +37,7 @@ CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
 CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_ESC_BATTERY=y
@@ -46,6 +46,7 @@ CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
 CONFIG_MODULES_FW_ATT_CONTROL=y
 CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_GYRO_CALIBRATION=y
 CONFIG_MODULES_GYRO_FFT=y
 CONFIG_MODULES_LAND_DETECTOR=y
@@ -61,7 +62,6 @@ CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
 CONFIG_MODULES_MC_POS_CONTROL=y
 CONFIG_MODULES_MC_RATE_CONTROL=y
-CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_NAVIGATOR=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_ROVER_POS_CONTROL=y
@@ -74,10 +74,10 @@ CONFIG_MODULES_SIMULATION_SIMULATOR_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
-CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/av/x-v1/nuttx-config/nsh/defconfig

@@ -138,6 +138,7 @@ CONFIG_NET_ARP_SEND=y
 CONFIG_NET_BROADCAST=y
 CONFIG_NET_ICMP=y
 CONFIG_NET_ICMP_SOCKET=y
+CONFIG_NET_NACTIVESOCKETS=16
 CONFIG_NET_SOLINGER=y
 CONFIG_NET_TCP=y
 CONFIG_NET_TCPBACKLOG=y

boards/av/x-v1/src/board_config.h

@@ -103,7 +103,6 @@
 #define HRT_TIMER_CHANNEL    1  /* use capture/compare channel 3 */
 
 /* RC Serial port */
-
 #define RC_SERIAL_PORT                     "/dev/ttyS4"
 
 /* Power switch controls ******************************************************/

boards/beaglebone/blue/cmake/init.cmake

@@ -35,8 +35,8 @@ add_compile_options(-Wno-cast-align)
 
 include(ExternalProject)
 ExternalProject_Add(librobotcontrol
-	GIT_REPOSITORY https://github.com/dagar/librobotcontrol.git
-	GIT_TAG 1abcb0a # latest as of 2019-12-29
+        GIT_REPOSITORY https://github.com/beagleboard/librobotcontrol.git
+        GIT_TAG 290e14f
 	CMAKE_CACHE_ARGS -DCMAKE_TOOLCHAIN_FILE:STRING=${CMAKE_TOOLCHAIN_FILE}
 	INSTALL_COMMAND ""
 	TEST_COMMAND ""

boards/beaglebone/blue/default.px4board

@@ -1,8 +1,9 @@
 CONFIG_PLATFORM_POSIX=y
-CONFIG_BOARD_LINUX=y
+CONFIG_BOARD_LINUX_TARGET=y
 CONFIG_BOARD_TOOLCHAIN="arm-linux-gnueabihf"
 CONFIG_BOARD_ARCHITECTURE="cortex-a8"
 CONFIG_BOARD_TESTING=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
@@ -16,7 +17,7 @@ CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y
 CONFIG_DRIVERS_LINUX_PWM_OUT=y
 CONFIG_DRIVERS_MAGNETOMETER_HMC5883=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_MODULES_AIRSPEED_SELECTOR=y
 CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
@@ -63,6 +64,7 @@ CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DYN=y
 CONFIG_SYSTEMCMDS_LED_CONTROL=y
 CONFIG_SYSTEMCMDS_PARAM=y

boards/cuav/nora/default.px4board

@@ -31,7 +31,9 @@ CONFIG_DRIVERS_PCA9685=y
 CONFIG_DRIVERS_PCA9685_PWM_OUT=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS5"
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_DRIVERS_ROBOCLAW=y
 CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SAFETY_BUTTON=y
@@ -81,8 +83,9 @@ CONFIG_MODULES_SIMULATION_SIMULATOR_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/cuav/x7pro/default.px4board

@@ -4,6 +4,7 @@ CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS0"
 CONFIG_BOARD_SERIAL_GPS2="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS5"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_COMMON_BAROMETERS=y
@@ -27,14 +28,13 @@ CONFIG_COMMON_LIGHT=y
 CONFIG_DRIVERS_LIGHTS_RGBLED_PWM=y
 CONFIG_COMMON_MAGNETOMETER=y
 CONFIG_COMMON_OPTICAL_FLOW=y
-CONFIG_DRIVERS_OSD=y
 CONFIG_DRIVERS_PCA9685=y
 CONFIG_DRIVERS_PCA9685_PWM_OUT=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_DRIVERS_ROBOCLAW=y
-CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SAFETY_BUTTON=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_COMMON_TELEMETRY=y
@@ -46,6 +46,7 @@ CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
 CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_ESC_BATTERY=y
@@ -54,6 +55,7 @@ CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
 CONFIG_MODULES_FW_ATT_CONTROL=y
 CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_GYRO_CALIBRATION=y
 CONFIG_MODULES_GYRO_FFT=y
 CONFIG_MODULES_LAND_DETECTOR=y
@@ -69,7 +71,6 @@ CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
 CONFIG_MODULES_MC_POS_CONTROL=y
 CONFIG_MODULES_MC_RATE_CONTROL=y
-CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_NAVIGATOR=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_ROVER_POS_CONTROL=y
@@ -80,10 +81,10 @@ CONFIG_MODULES_SIMULATION_SENSOR_GPS_SIM=y
 CONFIG_MODULES_SIMULATION_SENSOR_MAG_SIM=y
 CONFIG_MODULES_SIMULATION_SIMULATOR_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y
@@ -106,4 +107,3 @@ CONFIG_SYSTEMCMDS_USB_CONNECTED=y
 CONFIG_SYSTEMCMDS_VER=y
 CONFIG_SYSTEMCMDS_WORK_QUEUE=y
 CONFIG_EXAMPLES_FAKE_GPS=y
-#CONFIG_DRIVERS_TRANSPONDER_SAGETECH_MXS=y

boards/cubepilot/cubeorange/default.px4board

@@ -75,6 +75,7 @@ CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/cubepilot/cubeorange/nuttx-config/bootloader/defconfig

@@ -7,6 +7,7 @@
 #
 # CONFIG_DEV_CONSOLE is not set
 # CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
 # CONFIG_SPI_EXCHANGE is not set
 # CONFIG_STM32H7_SYSCFG is not set
 CONFIG_ARCH="arm"
@@ -22,13 +23,14 @@ CONFIG_ARMV7M_BASEPRI_WAR=y
 CONFIG_ARMV7M_ICACHE=y
 CONFIG_ARMV7M_MEMCPY=y
 CONFIG_ARMV7M_USEBASEPRI=y
-CONFIG_BOARDCTL=y
 CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARDCTL=y
 CONFIG_BOARD_INITTHREAD_PRIORITY=254
 CONFIG_BOARD_LATE_INITIALIZE=y
 CONFIG_BOARD_LOOPSPERMSEC=79954
 CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_C99_BOOL8=y
 CONFIG_CDCACM=y
 CONFIG_CDCACM_IFLOWCONTROL=y
 CONFIG_CDCACM_PRODUCTID=0x1016
@@ -37,17 +39,37 @@ CONFIG_CDCACM_RXBUFSIZE=600
 CONFIG_CDCACM_TXBUFSIZE=12000
 CONFIG_CDCACM_VENDORID=0x2DAE
 CONFIG_CDCACM_VENDORSTR="CubePilot"
+CONFIG_CLOCK_MONOTONIC=y
 CONFIG_DEBUG_FULLOPT=y
 CONFIG_DEBUG_SYMBOLS=y
 CONFIG_DEFAULT_SMALL=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MODCMDS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_PTHREAD=y
 CONFIG_EXPERIMENTAL=y
 CONFIG_FDCLONE_DISABLE=y
 CONFIG_FDCLONE_STDIO=y
 CONFIG_HAVE_CXX=y
 CONFIG_HAVE_CXXINITIALIZE=y
 CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_INIT_ENTRYPOINT="bootloader_main"
-CONFIG_INIT_STACKSIZE=2944
 CONFIG_LIBC_FLOATINGPOINT=y
 CONFIG_LIBC_LONG_LONG=y
 CONFIG_LIBC_STRERROR=y
@@ -58,6 +80,7 @@ CONFIG_PTHREAD_STACK_MIN=512
 CONFIG_RAM_SIZE=245760
 CONFIG_RAM_START=0x20010000
 CONFIG_RAW_BINARY=y
+CONFIG_SDCLONE_DISABLE=y
 CONFIG_SERIAL_TERMIOS=y
 CONFIG_SIG_DEFAULT=y
 CONFIG_SIG_SIGALRM_ACTION=y
@@ -87,3 +110,5 @@ CONFIG_USBDEV=y
 CONFIG_USBDEV_BUSPOWERED=y
 CONFIG_USBDEV_MAXPOWER=500
 CONFIG_USEC_PER_TICK=1000
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_INIT_ENTRYPOINT="bootloader_main"

boards/cubepilot/cubeorange/nuttx-config/nsh/defconfig

@@ -68,10 +68,10 @@ CONFIG_ARMV7M_MEMCPY=y
 CONFIG_ARMV7M_USEBASEPRI=y
 CONFIG_ARM_MPU_EARLY_RESET=y
 CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
 CONFIG_BOARD_CRASHDUMP=y
 CONFIG_BOARD_LOOPSPERMSEC=79954
 CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
 CONFIG_BUILTIN=y
 CONFIG_CDCACM=y
 CONFIG_CDCACM_IFLOWCONTROL=y

boards/cubepilot/cubeorange/test.px4board

@@ -1,12 +1,8 @@
 CONFIG_DRIVERS_ADC_ADS1115=n
 CONFIG_DRIVERS_IMU_ANALOG_DEVICES_ADIS16448=n
 CONFIG_DRIVERS_IRLOCK=n
-CONFIG_DRIVERS_PCA9685=n
 CONFIG_DRIVERS_PCA9685_PWM_OUT=n
-CONFIG_DRIVERS_RPM=n
 CONFIG_DRIVERS_UAVCAN=n
-CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=n
-CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=n
 CONFIG_MODULES_ROVER_POS_CONTROL=n
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=n
 CONFIG_BOARD_TESTING=y

boards/cubepilot/cubeyellow/default.px4board

@@ -80,8 +80,9 @@ CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
 CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/diatone/mamba-f405-mk2/default.px4board

@@ -16,7 +16,9 @@ CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y
 CONFIG_DRIVERS_MAGNETOMETER_AKM_AK8963=y
 CONFIG_DRIVERS_MAGNETOMETER_HMC5883=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS0"
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_COMMANDER=y

boards/diatone/mamba-f405-mk2/src/board_config.h

@@ -132,7 +132,6 @@
 #define GPIO_PPM_IN                  (GPIO_ALT|GPIO_AF2|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN8)
 
 #define RC_SERIAL_PORT               "/dev/ttyS0"
-#define BOARD_SUPPORTS_RC_SERIAL_PORT_OUTPUT
 
 /*
  * One RC_IN

boards/emlid/navio2/default.px4board

@@ -1,8 +1,9 @@
 CONFIG_PLATFORM_POSIX=y
-CONFIG_BOARD_LINUX=y
+CONFIG_BOARD_LINUX_TARGET=y
 CONFIG_BOARD_TOOLCHAIN="arm-linux-gnueabihf"
 CONFIG_BOARD_ARCHITECTURE="cortex-a53"
 CONFIG_BOARD_TESTING=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
 CONFIG_DRIVERS_ADC_ADS1115=y
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_MS5611=y
@@ -18,7 +19,7 @@ CONFIG_DRIVERS_IMU_ST_LSM9DS1=y
 CONFIG_DRIVERS_LINUX_PWM_OUT=y
 CONFIG_DRIVERS_MAGNETOMETER_HMC5883=y
 CONFIG_DRIVERS_MAGNETOMETER_LSM9DS1_MAG=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_MODULES_AIRSPEED_SELECTOR=y
 CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
@@ -66,6 +67,7 @@ CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DYN=y
 CONFIG_SYSTEMCMDS_LED_CONTROL=y
 CONFIG_SYSTEMCMDS_PARAM=y

boards/flywoo/gn-f405/default.px4board

@@ -5,23 +5,19 @@ CONFIG_BOARD_NO_HELP=y
 CONFIG_BOARD_CONSTRAINED_MEMORY=y
 CONFIG_BOARD_SERIAL_URT6="/dev/ttyS2"
 CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS0"
 CONFIG_DRIVERS_ADC_BOARD_ADC=y
 CONFIG_DRIVERS_BAROMETER_BMP280=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_GPS=y
-CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=n
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
-CONFIG_DRIVERS_MAGNETOMETER_QMC5883=y
-CONFIG_DRIVERS_OSD=y
 CONFIG_DRIVERS_PWM_OUT=y
 CONFIG_DRIVERS_RC_INPUT=y
-CONFIG_DRIVERS_TELEMETRY_FRSKY_TELEMETRY=n
-CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=n
-CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_COMMANDER=y
 CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
 CONFIG_MODULES_LAND_DETECTOR=y
 CONFIG_MODULES_LOAD_MON=y
@@ -33,14 +29,12 @@ CONFIG_MODULES_MC_RATE_CONTROL=y
 CONFIG_MODULES_NAVIGATOR=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_SENSORS=y
-CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
-CONFIG_SYSTEMCMDS_TOP=y
 CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_TOP=y
 CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
 CONFIG_SYSTEMCMDS_UORB=y
-CONFIG_SYSTEMCMDS_MIXER=y
-CONFIG_SYSTEMCMDS_PARAM=y
-CONFIG_SYSTEMCMDS_I2CDETECT=y
-CONFIG_SYSTEMCMDS_PWM=y
-CONFIG_SYSTEMCMDS_REBOOT=y
-CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_VER=y

boards/flywoo/gn-f405/nuttx-config/nsh/defconfig

@@ -6,9 +6,48 @@
 # modifications.
 #
 # CONFIG_DEV_CONSOLE is not set
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
 # CONFIG_MMCSD_HAVE_CARDDETECT is not set
 # CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
 # CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_CAT is not set
+# CONFIG_NSH_DISABLE_CD is not set
+# CONFIG_NSH_DISABLE_CP is not set
+# CONFIG_NSH_DISABLE_DATE is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MKFATFS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PS is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_RM is not set
+# CONFIG_NSH_DISABLE_RMDIR is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_SET is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
 # CONFIG_SPI_CALLBACK is not set
 # CONFIG_STM32_CCMEXCLUDE is not set
 CONFIG_ARCH="arm"
@@ -20,15 +59,17 @@ CONFIG_ARCH_CHIP="stm32"
 CONFIG_ARCH_CHIP_STM32=y
 CONFIG_ARCH_CHIP_STM32F405RG=y
 CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARCH_STACKDUMP=y
 CONFIG_ARMV7M_MEMCPY=y
 CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_ARM_MPU_EARLY_RESET=y
 CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
 CONFIG_BOARD_CRASHDUMP=y
 CONFIG_BOARD_CUSTOM_LEDS=y
 CONFIG_BOARD_LOOPSPERMSEC=16717
 CONFIG_BOARD_RESET_ON_ASSERT=2
 CONFIG_BUILTIN=y
-CONFIG_C99_BOOL8=y
 CONFIG_CDCACM=y
 CONFIG_CDCACM_IFLOWCONTROL=y
 CONFIG_CDCACM_PRODUCTID=0x0001
@@ -37,11 +78,14 @@ CONFIG_CDCACM_RXBUFSIZE=600
 CONFIG_CDCACM_TXBUFSIZE=2000
 CONFIG_CDCACM_VENDORID=0x26ac
 CONFIG_CDCACM_VENDORSTR="Flywoo"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
 CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
 CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
 CONFIG_DEV_PIPE_SIZE=70
-CONFIG_DISABLE_MQUEUE=y
-CONFIG_DISABLE_POSIX_TIMERS=y
+CONFIG_EXAMPLES_CALIB_UDELAY=y
 CONFIG_FAT_DMAMEMORY=y
 CONFIG_FAT_LCNAMES=y
 CONFIG_FAT_LFN=y
@@ -52,6 +96,7 @@ CONFIG_FS_CROMFS=y
 CONFIG_FS_FAT=y
 CONFIG_FS_FATTIME=y
 CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
 CONFIG_FS_PROCFS_REGISTER=y
 CONFIG_FS_ROMFS=y
 CONFIG_GRAN=y
@@ -61,37 +106,27 @@ CONFIG_HAVE_CXXINITIALIZE=y
 CONFIG_I2C=y
 CONFIG_I2C_RESET=y
 CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_MAX_EXITFUNS=1
 CONFIG_LIBC_STRERROR=y
 CONFIG_MEMSET_64BIT=y
 CONFIG_MEMSET_OPTSPEED=y
 CONFIG_MMCSD=y
 CONFIG_MM_REGIONS=2
+CONFIG_NAME_MAX=40
 CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
 CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
 CONFIG_NSH_CROMFSETC=y
-CONFIG_NSH_DISABLE_BASENAME=y
-CONFIG_NSH_DISABLE_DD=y
-CONFIG_NSH_DISABLE_DIRNAME=y
-CONFIG_NSH_DISABLE_HEXDUMP=y
-CONFIG_NSH_DISABLE_IFCONFIG=y
-CONFIG_NSH_DISABLE_IFUPDOWN=y
-CONFIG_NSH_DISABLE_LOSETUP=y
-CONFIG_NSH_DISABLE_MKFIFO=y
-CONFIG_NSH_DISABLE_MKRD=y
-CONFIG_NSH_DISABLE_PUT=y
-CONFIG_NSH_DISABLE_REBOOT=y
-CONFIG_NSH_DISABLE_TELNETD=y
-CONFIG_NSH_DISABLE_UNAME=y
-CONFIG_NSH_DISABLE_WGET=y
-CONFIG_NSH_DISABLE_XD=y
 CONFIG_NSH_FATDEVNO=0
-CONFIG_NSH_FILEIOSIZE=512
 CONFIG_NSH_LINELEN=128
 CONFIG_NSH_MAXARGUMENTS=15
 CONFIG_NSH_MMCSDSPIPORTNO=2
 CONFIG_NSH_NESTDEPTH=8
-CONFIG_NSH_READLINE=y
+CONFIG_NSH_QUOTE=y
 CONFIG_NSH_ROMFSETC=y
 CONFIG_NSH_ROMFSSECTSIZE=128
 CONFIG_NSH_STRERROR=y
@@ -99,23 +134,24 @@ CONFIG_NSH_VARS=y
 CONFIG_PIPES=y
 CONFIG_PREALLOC_TIMERS=50
 CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
 CONFIG_PTHREAD_STACK_MIN=512
 CONFIG_RAM_SIZE=196608
 CONFIG_RAM_START=0x20000000
 CONFIG_RAW_BINARY=y
 CONFIG_RTC_DATETIME=y
-CONFIG_SCHED_ATEXIT=y
 CONFIG_SCHED_HPWORK=y
 CONFIG_SCHED_HPWORKPRIORITY=249
 CONFIG_SCHED_HPWORKSTACKSIZE=1280
 CONFIG_SCHED_INSTRUMENTATION=y
 CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
 CONFIG_SCHED_LPWORK=y
 CONFIG_SCHED_LPWORKPRIORITY=50
 CONFIG_SCHED_LPWORKSTACKSIZE=1632
 CONFIG_SCHED_WAITPID=y
-CONFIG_SDCLONE_DISABLE=y
 CONFIG_SEM_PREALLOCHOLDERS=32
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
 CONFIG_SERIAL_TERMIOS=y
 CONFIG_SIG_DEFAULT=y
 CONFIG_SIG_SIGALRM_ACTION=y
@@ -156,7 +192,6 @@ CONFIG_STM32_SPI1_DMA_BUFFER=1024
 CONFIG_STM32_SPI2=y
 CONFIG_STM32_SPI2_DMA=y
 CONFIG_STM32_SPI3=y
-CONFIG_STM32_SPI_DMA=y
 CONFIG_STM32_SPI_DMATHRESHOLD=8
 CONFIG_STM32_TIM1=y
 CONFIG_STM32_TIM5=y
@@ -183,5 +218,3 @@ CONFIG_USBDEV=y
 CONFIG_USBDEV_BUSPOWERED=y
 CONFIG_USBDEV_MAXPOWER=500
 CONFIG_USEC_PER_TICK=1000
-CONFIG_USERMAIN_STACKSIZE=2944
-CONFIG_USER_ENTRYPOINT="nsh_main"

boards/flywoo/gn-f405/src/board_config.h

@@ -135,7 +135,6 @@
 #define GPIO_PPM_IN                  (GPIO_ALT|GPIO_AF2|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN8)
 
 #define RC_SERIAL_PORT               "/dev/ttyS0"
-#define BOARD_SUPPORTS_RC_SERIAL_PORT_OUTPUT
 
 /*
  * One RC_IN

boards/flywoo/gn-f405/src/usb.c

@@ -51,7 +51,7 @@
 #include <nuttx/usb/usbdev.h>
 #include <nuttx/usb/usbdev_trace.h>
 
-#include <arm_arch.h>
+#include <arm_internal.h>
 #include <stm32.h>
 #include "board_config.h"
 

boards/holybro/durandal-v1/default.px4board

@@ -28,10 +28,8 @@ CONFIG_DRIVERS_PCA9685=y
 CONFIG_DRIVERS_PCA9685_PWM_OUT=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_MODULES_SIMULATION_PWM_OUT_SIM=y
 CONFIG_DRIVERS_PX4IO=y
 CONFIG_DRIVERS_ROBOCLAW=y
-CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_COMMON_TELEMETRY=y
 CONFIG_DRIVERS_TONE_ALARM=y
@@ -40,6 +38,7 @@ CONFIG_MODULES_AIRSPEED_SELECTOR=y
 CONFIG_MODULES_BATTERY_STATUS=y
 CONFIG_MODULES_CAMERA_FEEDBACK=y
 CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_DATAMAN=y
 CONFIG_MODULES_EKF2=y
 CONFIG_MODULES_ESC_BATTERY=y
@@ -48,6 +47,7 @@ CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
 CONFIG_MODULES_FW_ATT_CONTROL=y
 CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_GYRO_CALIBRATION=y
 CONFIG_MODULES_GYRO_FFT=y
 CONFIG_MODULES_LAND_DETECTOR=y
@@ -62,7 +62,6 @@ CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
 CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
 CONFIG_MODULES_MC_POS_CONTROL=y
 CONFIG_MODULES_MC_RATE_CONTROL=y
-CONFIG_MODULES_CONTROL_ALLOCATOR=y
 CONFIG_MODULES_NAVIGATOR=y
 CONFIG_MODULES_RC_UPDATE=y
 CONFIG_MODULES_ROVER_POS_CONTROL=y
@@ -73,10 +72,10 @@ CONFIG_MODULES_SIMULATION_SENSOR_GPS_SIM=y
 CONFIG_MODULES_SIMULATION_SENSOR_MAG_SIM=y
 CONFIG_MODULES_SIMULATION_SIMULATOR_SIH=y
 CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
-CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/holybro/kakutef7/default.px4board

@@ -12,9 +12,8 @@ CONFIG_DRIVERS_BAROMETER_BMP280=y
 CONFIG_DRIVERS_DSHOT=y
 CONFIG_DRIVERS_IMU_INVENSENSE_ICM20689=y
 CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
-CONFIG_DRIVERS_OSD=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
 CONFIG_DRIVERS_TELEMETRY_FRSKY_TELEMETRY=y
 CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
 CONFIG_MODULES_BATTERY_STATUS=y

boards/holybro/kakutef7/src/board_config.h

@@ -111,7 +111,6 @@
 #define HRT_TIMER_CHANNEL       1  /* use capture/compare channel 1 */
 
 /* RC Serial port */
-
 #define RC_SERIAL_PORT                     "/dev/ttyS4"
 
 #define GPIO_RSSI_IN                       /* PC5  */ (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN5)

boards/holybro/kakuteh7/default.px4board

@@ -20,7 +20,7 @@ CONFIG_COMMON_MAGNETOMETER=y
 CONFIG_COMMON_OPTICAL_FLOW=y
 CONFIG_DRIVERS_POWER_MONITOR_INA226=y
 CONFIG_DRIVERS_PWM_OUT=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
 CONFIG_DRIVERS_ROBOCLAW=y
 CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
 CONFIG_COMMON_TELEMETRY=y
@@ -69,6 +69,7 @@ CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
 CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/holybro/kakuteh7/nuttx-config/bootloader/defconfig

@@ -7,6 +7,7 @@
 #
 # CONFIG_DEV_CONSOLE is not set
 # CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
 # CONFIG_SPI_EXCHANGE is not set
 # CONFIG_STM32H7_SYSCFG is not set
 CONFIG_ARCH="arm"
@@ -22,13 +23,14 @@ CONFIG_ARMV7M_BASEPRI_WAR=y
 CONFIG_ARMV7M_ICACHE=y
 CONFIG_ARMV7M_MEMCPY=y
 CONFIG_ARMV7M_USEBASEPRI=y
-CONFIG_BOARDCTL=y
 CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARDCTL=y
 CONFIG_BOARD_INITTHREAD_PRIORITY=254
 CONFIG_BOARD_LATE_INITIALIZE=y
 CONFIG_BOARD_LOOPSPERMSEC=22114
 CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_C99_BOOL8=y
 CONFIG_CDCACM=y
 CONFIG_CDCACM_IFLOWCONTROL=y
 CONFIG_CDCACM_PRODUCTID=0x0050
@@ -37,17 +39,37 @@ CONFIG_CDCACM_RXBUFSIZE=600
 CONFIG_CDCACM_TXBUFSIZE=12000
 CONFIG_CDCACM_VENDORID=0x3162
 CONFIG_CDCACM_VENDORSTR="Holybro"
+CONFIG_CLOCK_MONOTONIC=y
 CONFIG_DEBUG_FULLOPT=y
 CONFIG_DEBUG_SYMBOLS=y
 CONFIG_DEFAULT_SMALL=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MODCMDS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_PTHREAD=y
 CONFIG_EXPERIMENTAL=y
 CONFIG_FDCLONE_DISABLE=y
 CONFIG_FDCLONE_STDIO=y
 CONFIG_HAVE_CXX=y
 CONFIG_HAVE_CXXINITIALIZE=y
 CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_INIT_ENTRYPOINT="bootloader_main"
-CONFIG_INIT_STACKSIZE=2944
 CONFIG_LIBC_FLOATINGPOINT=y
 CONFIG_LIBC_LONG_LONG=y
 CONFIG_LIBC_STRERROR=y
@@ -58,6 +80,7 @@ CONFIG_PTHREAD_STACK_MIN=512
 CONFIG_RAM_SIZE=245760
 CONFIG_RAM_START=0x20010000
 CONFIG_RAW_BINARY=y
+CONFIG_SDCLONE_DISABLE=y
 CONFIG_SERIAL_TERMIOS=y
 CONFIG_SIG_DEFAULT=y
 CONFIG_SIG_SIGALRM_ACTION=y
@@ -87,3 +110,5 @@ CONFIG_USBDEV=y
 CONFIG_USBDEV_BUSPOWERED=y
 CONFIG_USBDEV_MAXPOWER=500
 CONFIG_USEC_PER_TICK=1000
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_INIT_ENTRYPOINT="bootloader_main"

boards/holybro/kakuteh7/nuttx-config/nsh/defconfig

@@ -14,31 +14,14 @@
 # CONFIG_NSH_DISABLEBG is not set
 # CONFIG_NSH_DISABLESCRIPT is not set
 # CONFIG_NSH_DISABLE_DF is not set
-# CONFIG_NSH_DISABLE_ECHO is not set
-# CONFIG_NSH_DISABLE_ENV is not set
 # CONFIG_NSH_DISABLE_EXEC is not set
 # CONFIG_NSH_DISABLE_EXIT is not set
-# CONFIG_NSH_DISABLE_FREE is not set
 # CONFIG_NSH_DISABLE_GET is not set
-# CONFIG_NSH_DISABLE_HELP is not set
 # CONFIG_NSH_DISABLE_ITEF is not set
-# CONFIG_NSH_DISABLE_KILL is not set
 # CONFIG_NSH_DISABLE_LOOPS is not set
-# CONFIG_NSH_DISABLE_LS is not set
-# CONFIG_NSH_DISABLE_MKDIR is not set
 # CONFIG_NSH_DISABLE_MKFATFS is not set
-# CONFIG_NSH_DISABLE_MOUNT is not set
-# CONFIG_NSH_DISABLE_MV is not set
-# CONFIG_NSH_DISABLE_PRINTF is not set
-# CONFIG_NSH_DISABLE_PWD is not set
 # CONFIG_NSH_DISABLE_SEMICOLON is not set
-# CONFIG_NSH_DISABLE_SLEEP is not set
-# CONFIG_NSH_DISABLE_SOURCE is not set
-# CONFIG_NSH_DISABLE_TEST is not set
 # CONFIG_NSH_DISABLE_TIME is not set
-# CONFIG_NSH_DISABLE_UMOUNT is not set
-# CONFIG_NSH_DISABLE_UNSET is not set
-# CONFIG_NSH_DISABLE_USLEEP is not set
 # CONFIG_SPI_CALLBACK is not set
 CONFIG_ARCH="arm"
 CONFIG_ARCH_BOARD_CUSTOM=y
@@ -58,11 +41,13 @@ CONFIG_ARMV7M_MEMCPY=y
 CONFIG_ARMV7M_USEBASEPRI=y
 CONFIG_ARM_MPU_EARLY_RESET=y
 CONFIG_BOARDCTL_RESET=y
-CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARDCTL=y
 CONFIG_BOARD_CRASHDUMP=y
 CONFIG_BOARD_LOOPSPERMSEC=95150
 CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
 CONFIG_BUILTIN=y
+CONFIG_C99_BOOL8=y
 CONFIG_CDCACM=y
 CONFIG_CDCACM_IFLOWCONTROL=y
 CONFIG_CDCACM_PRODUCTID=0x004b
@@ -71,11 +56,31 @@ CONFIG_CDCACM_RXBUFSIZE=600
 CONFIG_CDCACM_TXBUFSIZE=12000
 CONFIG_CDCACM_VENDORID=0x3162
 CONFIG_CDCACM_VENDORSTR="Holybro"
+CONFIG_CLOCK_MONOTONIC=y
 CONFIG_DEBUG_FULLOPT=y
 CONFIG_DEBUG_HARDFAULT_ALERT=y
 CONFIG_DEBUG_MEMFAULT=y
 CONFIG_DEBUG_SYMBOLS=y
 CONFIG_DEFAULT_SMALL=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MODCMDS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
 CONFIG_DEV_FIFO_SIZE=0
 CONFIG_DEV_PIPE_MAXSIZE=1024
 CONFIG_DEV_PIPE_SIZE=70
@@ -101,11 +106,8 @@ CONFIG_HAVE_CXXINITIALIZE=y
 CONFIG_I2C=y
 CONFIG_I2C_RESET=y
 CONFIG_IDLETHREAD_STACKSIZE=750
-CONFIG_INIT_ENTRYPOINT="nsh_main"
-CONFIG_INIT_STACKSIZE=2944
 CONFIG_LIBC_FLOATINGPOINT=y
 CONFIG_LIBC_LONG_LONG=y
-CONFIG_LIBC_MAX_EXITFUNS=1
 CONFIG_LIBC_STRERROR=y
 CONFIG_MEMSET_64BIT=y
 CONFIG_MEMSET_OPTSPEED=y
@@ -123,6 +125,9 @@ CONFIG_NSH_ARGCAT=y
 CONFIG_NSH_BUILTIN_APPS=y
 CONFIG_NSH_CMDPARMS=y
 CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_DISABLE_IFCONFIG=y
+CONFIG_NSH_DISABLE_IFUPDOWN=y
+CONFIG_NSH_DISABLE_TELNETD=y
 CONFIG_NSH_LINELEN=128
 CONFIG_NSH_MAXARGUMENTS=15
 CONFIG_NSH_MMCSDSPIPORTNO=1
@@ -145,6 +150,7 @@ CONFIG_RAW_BINARY=y
 CONFIG_READLINE_CMD_HISTORY=y
 CONFIG_READLINE_TABCOMPLETION=y
 CONFIG_RTC_DATETIME=y
+CONFIG_LIBC_MAX_EXITFUNS=1
 CONFIG_SCHED_HPWORK=y
 CONFIG_SCHED_HPWORKPRIORITY=249
 CONFIG_SCHED_HPWORKSTACKSIZE=1280
@@ -155,6 +161,7 @@ CONFIG_SCHED_LPWORK=y
 CONFIG_SCHED_LPWORKPRIORITY=50
 CONFIG_SCHED_LPWORKSTACKSIZE=1632
 CONFIG_SCHED_WAITPID=y
+CONFIG_SDCLONE_DISABLE=y
 CONFIG_SEM_PREALLOCHOLDERS=32
 CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
 CONFIG_SERIAL_TERMIOS=y
@@ -194,6 +201,7 @@ CONFIG_STM32H7_SPI2=y
 CONFIG_STM32H7_SPI4=y
 CONFIG_STM32H7_SPI4_DMA=y
 CONFIG_STM32H7_SPI4_DMA_BUFFER=1024
+CONFIG_STM32H7_SPI_DMA=y
 CONFIG_STM32H7_UART4=y
 CONFIG_STM32H7_UART7=y
 CONFIG_STM32H7_USART1=y
@@ -233,4 +241,6 @@ CONFIG_USBDEV=y
 CONFIG_USBDEV_BUSPOWERED=y
 CONFIG_USBDEV_MAXPOWER=500
 CONFIG_USEC_PER_TICK=1000
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_INIT_ENTRYPOINT="nsh_main"
 CONFIG_WATCHDOG=y

boards/holybro/kakuteh7/src/init.c

@@ -194,12 +194,14 @@ stm32_boardinitialize(void)
  *
  ****************************************************************************/
 
+
 __EXPORT int board_app_initialize(uintptr_t arg)
 {
 	/* Power on Interfaces */
 	board_control_spi_sensors_power(true, 0xffff);
 
 	/* Need hrt running before using the ADC */
+
 	px4_platform_init();
 
 	/* configure SPI interfaces */
@@ -207,6 +209,7 @@ __EXPORT int board_app_initialize(uintptr_t arg)
 	stm32_spiinitialize();
 
 	/* configure the DMA allocator */
+
 	if (board_dma_alloc_init() < 0) {
 		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
 	}

boards/holybro/pix32v5/default.px4board

@@ -34,7 +34,9 @@ CONFIG_DRIVERS_PWM_INPUT=y
 CONFIG_DRIVERS_PWM_OUT=y
 CONFIG_MODULES_SIMULATION_PWM_OUT_SIM=y
 CONFIG_DRIVERS_PX4IO=y
-CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_COMMON_RC=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
+CONFIG_DRIVERS_RC_PPM_IN=y
 CONFIG_DRIVERS_ROBOCLAW=y
 CONFIG_DRIVERS_RPM=y
 CONFIG_DRIVERS_SAFETY_BUTTON=y
@@ -85,8 +87,9 @@ CONFIG_MODULES_UUV_ATT_CONTROL=y
 CONFIG_MODULES_UUV_POS_CONTROL=y
 CONFIG_MODULES_GIMBAL=y
 CONFIG_MODULES_VTOL_ATT_CONTROL=y
-CONFIG_SYSTEMCMDS_BL_UPDATE=y
 CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_BSONDUMP=y
 CONFIG_SYSTEMCMDS_DMESG=y
 CONFIG_SYSTEMCMDS_DUMPFILE=y
 CONFIG_SYSTEMCMDS_GPIO=y

boards/holybro/pix32v5/src/board_config.h

@@ -283,7 +283,6 @@
 #define GPIO_PPM_IN             /* PI5 T8C1 */ GPIO_TIM8_CH1IN_2
 
 /* RC Serial port */
-
 #define RC_SERIAL_PORT                     "/dev/ttyS4"
 #define RC_SERIAL_SINGLEWIRE
 

boards/matek/h743-mini/bootloader.px4board

@@ -0,0 +1,3 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ROMFSROOT=""

boards/matek/h743-mini/default.px4board

@@ -0,0 +1,90 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS2"
+CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
+CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
+CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_DRIVERS_BAROMETER_DPS310=y
+CONFIG_DRIVERS_CAMERA_CAPTURE=n
+CONFIG_DRIVERS_CAMERA_TRIGGER=n
+CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_INVENSENSE_MPU6000=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM42605=y
+CONFIG_DRIVERS_MAGNETOMETER_QMC5883L=y
+CONFIG_COMMON_DISTANCE_SENSOR=n
+CONFIG_COMMON_LIGHT=n
+CONFIG_COMMON_MAGNETOMETER=n
+CONFIG_COMMON_OPTICAL_FLOW=y
+CONFIG_DRIVERS_OSD=y
+CONFIG_DRIVERS_PWM_OUT=y
+CONFIG_DRIVERS_PWM_OUT_SIM=n
+CONFIG_COMMON_RC=y
+CONFIG_BOARD_SERIAL_RC="/dev/ttyS4"
+CONFIG_DRIVERS_RPM=n
+CONFIG_COMMON_TELEMETRY=y
+CONFIG_DRIVERS_TONE_ALARM=y
+CONFIG_DRIVERS_UAVCAN=y
+CONFIG_BOARD_UAVCAN_INTERFACES=1
+CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
+CONFIG_MODULES_BATTERY_STATUS=y
+CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
+CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_EVENTS=y
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_FW_ATT_CONTROL=y
+CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_GYRO_FFT=y
+CONFIG_MODULES_LAND_DETECTOR=y
+CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+CONFIG_MODULES_LOAD_MON=y
+CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y
+CONFIG_MODULES_LOGGER=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_MANUAL_CONTROL=y
+CONFIG_MODULES_MAVLINK=y
+CONFIG_MODULES_MC_ATT_CONTROL=y
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=n
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+CONFIG_MODULES_MC_POS_CONTROL=y
+CONFIG_MODULES_MC_RATE_CONTROL=y
+CONFIG_MODULES_MICRODDS_CLIENT=y
+CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODULES_RC_UPDATE=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_MODULES_TEMPERATURE_COMPENSATION=n
+CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_MODULES_GIMBAL=n
+CONFIG_SYSTEMCMDS_BL_UPDATE=n
+CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_DUMPFILE=n
+CONFIG_SYSTEMCMDS_GPIO=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_LED_CONTROL=n
+CONFIG_SYSTEMCMDS_MFT=n
+CONFIG_SYSTEMCMDS_MOTOR_TEST=n
+CONFIG_SYSTEMCMDS_MTD=n
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SD_BENCH=n
+CONFIG_SYSTEMCMDS_SD_STRESS=n
+CONFIG_SYSTEMCMDS_SERIAL_TEST=n
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_TUNE_CONTROL=n
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y
+CONFIG_EXAMPLES_FAKE_GPS=n

boards/matek/h743-mini/firmware.prototype

@@ -0,0 +1,13 @@
+{
+    "board_id": 1013,
+    "magic": "PX4FWv1",
+    "description": "Firmware for the MatekH743-slim board",
+    "image": "",
+    "build_time": 0,
+    "summary": "MatekH743-mini",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 1966080,
+    "git_identity": "",
+    "board_revision": 0
+}

boards/matek/h743-mini/init/rc.board_extras

@@ -0,0 +1,16 @@
+#!/bin/sh
+#
+# board specific extras init
+#------------------------------------------------------------------------------
+
+# if ! param compare OSD_ATXXXX_CFG 0
+# then
+# 	atxxxx start -s
+# fi
+
+atxxxx start -s
+
+
+# DShot telemetry is always on UART7
+# dshot telemetry /dev/ttyS5
+

boards/matek/h743-mini/init/rc.board_sensors

@@ -0,0 +1,22 @@
+#!/bin/sh
+#
+# board specific sensors init
+#------------------------------------------------------------------------------
+
+board_adc start
+
+# Internal SPI bus ICM-42605
+if ! icm42605 -R 14 -s start
+then
+	# internal SPI bus ICM-20602
+	icm20602 -R 12 -s start
+fi
+
+# Internal SPI bus MPU-6000
+mpu6000 -R 12 -s start
+
+# Internal baro
+dps310 -I start -a 118
+
+# External mag
+qmc5883l -X start -a 13

boards/matek/h743-mini/nuttx-config/Kconfig

@@ -0,0 +1,17 @@
+#
+# For a description of the syntax of this configuration file,
+# see misc/tools/kconfig-language.txt.
+#
+config BOARD_HAS_PROBES
+	bool "Board provides GPIO or other Hardware for signaling to timing analyze."
+	default y
+	---help---
+		This board provides GPIO FMU-CH1-5, CAP1-6 as PROBE_1-11 to provide timing signals from selected drivers.
+
+config BOARD_USE_PROBES
+	bool "Enable the use the board provided FMU-CH1-5, CAP1-6 as PROBE_1-11"
+	default n
+	depends on BOARD_HAS_PROBES
+
+	---help---
+		Select to use GPIO FMU-CH1-5, CAP1-6  to provide timing signals from selected drivers.

boards/matek/h743-mini/nuttx-config/bootloader/defconfig

@@ -0,0 +1,113 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DEV_CONSOLE is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_SPI_EXCHANGE is not set
+# CONFIG_STM32H7_SYSCFG is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/matek/h743-mini/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743VI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARDCTL=y
+CONFIG_BOARD_INITTHREAD_PRIORITY=254
+CONFIG_BOARD_LATE_INITIALIZE=y
+CONFIG_BOARD_LOOPSPERMSEC=22114
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_C99_BOOL8=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_PRODUCTID=0x004b
+CONFIG_CDCACM_PRODUCTSTR="Matek H743-mini"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x3162
+CONFIG_CDCACM_VENDORSTR="Matek"
+CONFIG_CLOCK_MONOTONIC=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MODCMDS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_DISABLE_MQUEUE=y
+CONFIG_DISABLE_PTHREAD=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FDCLONE_DISABLE=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SPI=y
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=32
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_USART1=y
+CONFIG_SYSTEMTICK_HOOK=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGINT_CHAR=0x03
+CONFIG_TTY_SIGTSTP=y
+CONFIG_USART1_RXBUFSIZE=600
+CONFIG_USART1_TXBUFSIZE=300
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_INIT_ENTRYPOINT="bootloader_main"

boards/matek/h743-mini/nuttx-config/include/board.h

@@ -0,0 +1,493 @@
+/************************************************************************************
+ * nuttx-configs/px4_fmu-v6u/include/board.h
+ *
+ *   Copyright (C) 2016-2019 Gregory Nutt. All rights reserved.
+ *   Authors: David Sidrane <david.sidrane@nscdg.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+#ifndef __NUTTX_CONFIG_MATEKH743SLIM_INCLUDE_BOARD_H
+#define __NUTTX_CONFIG_MATEKH743SLIM_INCLUDE_BOARD_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include "board_dma_map.h"
+
+#include <nuttx/config.h>
+
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+
+#include "stm32_rcc.h"
+#include "stm32_sdmmc.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+/* The MatekH743-Slim  board provides the following clock sources:
+ *
+ *   X1: 8 MHz crystal for HSE
+ *
+ * So we have these clock source available within the STM32
+ *
+ *   HSI: 64 MHz RC factory-trimmed
+ *   HSE:  8 MHz crystal for HSE
+ */
+
+#define STM32_BOARD_XTAL        8000000ul
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+#define STM32_LSE_FREQUENCY     32768
+
+/* Main PLL Configuration.
+ *
+ * PLL source is HSE = 8,000,000
+ *
+ * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
+ * Subject to:
+ *
+ *     1 <= PLLM <= 63
+ *     4 <= PLLN <= 512
+ *   150 MHz <= PLL_VCOL <= 420MHz
+ *   192 MHz <= PLL_VCOH <= 836MHz
+ *
+ * SYSCLK  = PLL_VCO / PLLP
+ * CPUCLK  = SYSCLK / D1CPRE
+ * Subject to
+ *
+ *   PLLP1   = {2, 4, 6, 8, ..., 128}
+ *   PLLP2,3 = {2, 3, 4, ..., 128}
+ *   CPUCLK <= 480 MHz
+ */
+
+#define STM32_BOARD_USEHSE
+
+#define STM32_PLLCFG_PLLSRC      RCC_PLLCKSELR_PLLSRC_HSE
+
+/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR
+ *
+ *   PLL1_VCO = (8,000,000 / 1) * 120 = 960 MHz
+ *
+ *   PLL1P = PLL1_VCO/2  = 960 MHz / 2   = 480 MHz
+ *   PLL1Q = PLL1_VCO/4  = 960 MHz / 4   = 240 MHz
+ *   PLL1R = PLL1_VCO/8  = 960 MHz / 8   = 120 MHz
+ */
+
+#define STM32_PLLCFG_PLL1CFG    (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVP1EN | \
+				 RCC_PLLCFGR_DIVQ1EN | \
+				 RCC_PLLCFGR_DIVR1EN)
+#define STM32_PLLCFG_PLL1M       RCC_PLLCKSELR_DIVM1(1)
+#define STM32_PLLCFG_PLL1N       RCC_PLL1DIVR_N1(120)
+#define STM32_PLLCFG_PLL1P       RCC_PLL1DIVR_P1(2)
+#define STM32_PLLCFG_PLL1Q       RCC_PLL1DIVR_Q1(4)
+#define STM32_PLLCFG_PLL1R       RCC_PLL1DIVR_R1(8)
+
+#define STM32_VCO1_FREQUENCY     ((STM32_HSE_FREQUENCY / 1) * 120)
+#define STM32_PLL1P_FREQUENCY    (STM32_VCO1_FREQUENCY / 2)
+#define STM32_PLL1Q_FREQUENCY    (STM32_VCO1_FREQUENCY / 4)
+#define STM32_PLL1R_FREQUENCY    (STM32_VCO1_FREQUENCY / 8)
+
+/* PLL2 */
+
+#define STM32_PLLCFG_PLL2CFG     (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \
+				  RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \
+				  RCC_PLLCFGR_DIVP2EN | \
+				  RCC_PLLCFGR_DIVQ2EN | \
+				  RCC_PLLCFGR_DIVR2EN)
+#define STM32_PLLCFG_PLL2M       RCC_PLLCKSELR_DIVM2(2)
+#define STM32_PLLCFG_PLL2N       RCC_PLL2DIVR_N2(48)
+#define STM32_PLLCFG_PLL2P       RCC_PLL2DIVR_P2(2)
+#define STM32_PLLCFG_PLL2Q       RCC_PLL2DIVR_Q2(2)
+#define STM32_PLLCFG_PLL2R       RCC_PLL2DIVR_R2(2)
+
+#define STM32_VCO2_FREQUENCY     ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL2P_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2Q_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2R_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+
+/* PLL3 */
+
+#define STM32_PLLCFG_PLL3CFG    (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVQ3EN)
+#define STM32_PLLCFG_PLL3M      RCC_PLLCKSELR_DIVM3(2)
+#define STM32_PLLCFG_PLL3N      RCC_PLL3DIVR_N3(48)
+#define STM32_PLLCFG_PLL3P      RCC_PLL3DIVR_P3(2)
+#define STM32_PLLCFG_PLL3Q      RCC_PLL3DIVR_Q3(4)
+#define STM32_PLLCFG_PLL3R      RCC_PLL3DIVR_R3(2)
+
+#define STM32_VCO3_FREQUENCY    ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL3P_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+#define STM32_PLL3Q_FREQUENCY   (STM32_VCO3_FREQUENCY / 4)
+#define STM32_PLL3R_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+
+/* SYSCLK = PLL1P = 480MHz
+ * CPUCLK = SYSCLK / 1 = 480 MHz
+ */
+
+#define STM32_RCC_D1CFGR_D1CPRE  (RCC_D1CFGR_D1CPRE_SYSCLK)
+#define STM32_SYSCLK_FREQUENCY   (STM32_PLL1P_FREQUENCY)
+#define STM32_CPUCLK_FREQUENCY   (STM32_SYSCLK_FREQUENCY / 1)
+
+/* Configure Clock Assignments */
+
+/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max)
+ * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 240
+ */
+
+#define STM32_RCC_D1CFGR_HPRE   RCC_D1CFGR_HPRE_SYSCLKd2        /* HCLK  = SYSCLK / 2 */
+#define STM32_ACLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* ACLK in D1, HCLK3 in D1 */
+#define STM32_HCLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* HCLK in D2, HCLK4 in D3 */
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY            /* same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE1  RCC_D2CFGR_D2PPRE1_HCLKd2       /* PCLK1 = HCLK / 2 */
+#define STM32_PCLK1_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB2 clock (PCLK2) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE2  RCC_D2CFGR_D2PPRE2_HCLKd2       /* PCLK2 = HCLK / 2 */
+#define STM32_PCLK2_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB3 clock (PCLK3) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D1CFGR_D1PPRE   RCC_D1CFGR_D1PPRE_HCLKd2        /* PCLK3 = HCLK / 2 */
+#define STM32_PCLK3_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB4 clock (PCLK4) is HCLK/4 (120 MHz) */
+
+#define STM32_RCC_D3CFGR_D3PPRE   RCC_D3CFGR_D3PPRE_HCLKd2       /* PCLK4 = HCLK / 2 */
+#define STM32_PCLK4_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* Timer clock frequencies */
+
+/* Timers driven from APB1 will be twice PCLK1 */
+
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* Timers driven from APB2 will be twice PCLK2 */
+
+#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM15_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM16_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM17_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+
+/* Kernel Clock Configuration
+ *
+ * Note: look at Table 54 in ST Manual
+ */
+
+/* I2C123 clock source */
+
+#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI
+
+/* I2C4 clock source */
+
+#define STM32_RCC_D3CCIPR_I2C4SRC    RCC_D3CCIPR_I2C4SEL_HSI
+
+/* SPI123 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2
+
+/* SPI45 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI45SRC  RCC_D2CCIP1R_SPI45SEL_PLL2
+
+/* SPI6 clock source */
+
+#define STM32_RCC_D3CCIPR_SPI6SRC    RCC_D3CCIPR_SPI6SEL_PLL2
+
+/* USB 1 and 2 clock source */
+
+#define STM32_RCC_D2CCIP2R_USBSRC    RCC_D2CCIP2R_USBSEL_PLL3
+
+/* ADC 1 2 3 clock source */
+
+#define STM32_RCC_D3CCIPR_ADCSEL     RCC_D3CCIPR_ADCSEL_PLL2
+
+/* FDCAN 1 clock source */
+
+#define STM32_RCC_D2CCIP1R_FDCANSEL  RCC_D2CCIP1R_FDCANSEL_HSE   /* FDCAN 1 2 clock source */
+
+#define STM32_FDCANCLK               STM32_HSE_FREQUENCY
+
+/* FLASH wait states
+ *
+ *  ------------ ---------- -----------
+ *  Vcore        MAX ACLK   WAIT STATES
+ *  ------------ ---------- -----------
+ *  1.15-1.26 V     70 MHz    0
+ *  (VOS1 level)   140 MHz    1
+ *                 210 MHz    2
+ *  1.05-1.15 V     55 MHz    0
+ *  (VOS2 level)   110 MHz    1
+ *                 165 MHz    2
+ *                 220 MHz    3
+ *  0.95-1.05 V     45 MHz    0
+ *  (VOS3 level)    90 MHz    1
+ *                 135 MHz    2
+ *                 180 MHz    3
+ *                 225 MHz    4
+ *  ------------ ---------- -----------
+ */
+
+#define BOARD_FLASH_WAITSTATES 2
+
+/* SDMMC definitions ********************************************************/
+
+/* Init 480kHz, freq = PLL1Q/(2*div)  div =  PLL1Q/(2*freq) */
+
+#define STM32_SDMMC_INIT_CLKDIV     (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+
+/* 20 MHz Max for now - more reliable on some boards than 25 MHz
+ * 20 MHz = PLL1Q/(2*div), div =  PLL1Q/(2*freq), div = 6 = 240 / 40
+ */
+
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (6 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_SDXFR_CLKDIV    (6 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_SDXFR_CLKDIV    (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+
+#define STM32_SDMMC_CLKCR_EDGE      STM32_SDMMC_CLKCR_NEGEDGE
+
+/* LED definitions ******************************************************************/
+/* The board has two, LED_GREEN a Green LED and LED_BLUE a Blue LED,
+ * that can be controlled by software.
+ *
+ * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
+ * The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with board_userled() */
+
+#define BOARD_LED1        0
+#define BOARD_LED2        1
+#define BOARD_NLEDS       2
+
+#define BOARD_LED_BLUE    BOARD_LED1
+#define BOARD_LED_GREEN   BOARD_LED2
+
+/* LED bits for use with board_userled_all() */
+
+#define BOARD_LED1_BIT    (1 << BOARD_LED1)
+#define BOARD_LED2_BIT    (1 << BOARD_LED2)
+
+/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
+ * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
+ * events as follows:
+ *
+ *
+ *   SYMBOL                     Meaning                      LED state
+ *                                                        Red   Green Blue
+ *   ----------------------  --------------------------  ------ ------ ----*/
+
+#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
+#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
+#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
+#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
+#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
+#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
+#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
+#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
+#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */
+
+/* Thus if the Green LED is statically on, NuttX has successfully booted and
+ * is, apparently, running normally.  If the Red LED is flashing at
+ * approximately 2Hz, then a fatal error has been detected and the system
+ * has halted.
+ */
+
+/* Alternate function pin selections ************************************************/
+
+#define GPIO_USART1_RX   GPIO_USART1_RX_2   /* PA10 */
+#define GPIO_USART1_TX   GPIO_USART1_TX_2   /* PA9  */
+
+#define GPIO_USART2_RX   GPIO_USART2_RX_2   /* PD6  */
+#define GPIO_USART2_TX   GPIO_USART2_TX_2   /* PD5  */
+
+#define GPIO_USART3_RX   GPIO_USART3_RX_3   /* PD9  */
+#define GPIO_USART3_TX   GPIO_USART3_TX_3   /* PD8  */
+
+#define GPIO_UART4_RX    GPIO_UART4_RX_3    /* PB8  */
+#define GPIO_UART4_TX    GPIO_UART4_TX_3    /* PB9  */
+
+#define GPIO_USART6_RX   GPIO_USART6_RX_1   /* PC7  */
+#define GPIO_USART6_TX   GPIO_USART6_TX_1   /* PC6  */
+
+#define GPIO_UART7_RX    GPIO_UART7_RX_3    /* PE7  */
+#define GPIO_UART7_TX    GPIO_UART7_TX_3    /* PE8  */
+#define GPIO_UART7_RTS   GPIO_UART7_RTS_1   /* PE9  */
+#define GPIO_UART7_CTS   GPIO_UART7_CTS_1   /* PE10 */
+
+#define GPIO_UART8_RX    GPIO_UART8_RX_1    /* PE0  */
+#define GPIO_UART8_TX    GPIO_UART8_TX_1    /* PE1  */
+
+
+/* CAN
+ *
+ * CAN1 is routed to transceiver.
+ */
+
+#define GPIO_CAN1_RX     GPIO_CAN1_RX_3     /* PD0  */
+#define GPIO_CAN1_TX     GPIO_CAN1_TX_3     /* PD1  */
+
+/* SPI
+ *
+ * SPI1 is MPU6000
+ * SPI2 is MAX7456
+ * SPI3 is extern with PD4 and PE2 as CS
+ * SPI4 is ICM20602
+ */
+
+#define ADJ_SLEW_RATE(p) (((p) & ~GPIO_SPEED_MASK) | (GPIO_SPEED_2MHz))
+
+#define GPIO_SPI1_MISO   GPIO_SPI1_MISO_1               /* PA6  */
+#define GPIO_SPI1_MOSI   GPIO_SPI1_MOSI_3               /* PD7  */
+#define GPIO_SPI1_SCK    ADJ_SLEW_RATE(GPIO_SPI1_SCK_1) /* PA5  */
+
+#define GPIO_SPI2_MISO   GPIO_SPI2_MISO_1               /* PB14 */
+#define GPIO_SPI2_MOSI   GPIO_SPI2_MOSI_1               /* PB15 */
+#define GPIO_SPI2_SCK    ADJ_SLEW_RATE(GPIO_SPI2_SCK_4) /* PB13 */
+
+#define GPIO_SPI3_MISO   GPIO_SPI3_MISO_1               /* PB4  */
+#define GPIO_SPI3_MOSI   GPIO_SPI3_MOSI_4               /* PB5  */
+#define GPIO_SPI3_SCK    ADJ_SLEW_RATE(GPIO_SPI3_SCK_1) /* PB3  */
+
+#define GPIO_SPI4_MISO   GPIO_SPI4_MISO_1               /* PE13 */
+#define GPIO_SPI4_MOSI   GPIO_SPI4_MOSI_1               /* PE14 */
+#define GPIO_SPI4_SCK    ADJ_SLEW_RATE(GPIO_SPI4_SCK_1) /* PE12 */
+
+/* I2C
+ *
+ *   The optional _GPIO configurations allow the I2C driver to manually
+ *   reset the bus to clear stuck slaves.  They match the pin configuration,
+ *   but are normally-high GPIOs.
+ *
+ */
+
+#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1       /* PB6  */
+#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1       /* PB7  */
+
+#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
+#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
+
+#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1       /* PB10 */
+#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1       /* PB11 */
+
+#define GPIO_I2C2_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN10)
+#define GPIO_I2C2_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN11)
+
+/* SDMMC1
+ *
+ *      SDMMC1_D0                          PC8
+ *      SDMMC1_D1                          PC9
+ *      SDMMC1_D2                          PC10
+ *      SDMMC1_D3                          PC11
+ *      SDMMC1_CK                          PC12
+ *      SDMMC1_CMD                         PD2
+ */
+
+// #define GPIO_SDMMC1_D0   GPIO_SDMMC1_D0    /* PC8  */
+// #define GPIO_SDMMC1_D1   GPIO_SDMMC1_D1    /* PC9  */
+// #define GPIO_SDMMC1_D2   GPIO_SDMMC1_D2    /* PC10 */
+// #define GPIO_SDMMC1_D3   GPIO_SDMMC1_D3    /* PC11 */
+// #define GPIO_SDMMC1_CK   GPIO_SDMMC1_CK    /* PC12 */
+// #define GPIO_SDMMC1_CMD  GPIO_SDMMC1_CMD   /* PD2  */
+
+
+/* USB
+ *
+ *      OTG_FS_DM                           PA11
+ *      OTG_FS_DP                           PA12
+ *      VBUS                                PA9
+ */
+
+
+/* Board provides GPIO or other Hardware for signaling to timing analyzer */
+
+#if defined(CONFIG_BOARD_USE_PROBES)
+# include "stm32_gpio.h"
+# define PROBE_N(n) (1<<((n)-1))
+# define PROBE_1    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTI|GPIO_PIN0)   /* PI0 AUX1 */
+# define PROBE_2    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN12)  /* PH12 AUX2 */
+# define PROBE_3    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN11)  /* PH11 AUX3 */
+# define PROBE_4    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN10)  /* PH10 AUX4 */
+# define PROBE_5    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13)  /* PD13 AUX5 */
+# define PROBE_6    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14)  /* PD14 AUX6 */
+# define PROBE_7    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN6)   /* PH6  AUX7 */
+# define PROBE_8    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTH|GPIO_PIN9)   /* PH9  AUX8 */
+# define PROBE_9    (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN11)  /* PE11  CAP1 */
+
+# define PROBE_INIT(mask) \
+	do { \
+		if ((mask)& PROBE_N(1)) { stm32_configgpio(PROBE_1); } \
+		if ((mask)& PROBE_N(2)) { stm32_configgpio(PROBE_2); } \
+		if ((mask)& PROBE_N(3)) { stm32_configgpio(PROBE_3); } \
+		if ((mask)& PROBE_N(4)) { stm32_configgpio(PROBE_4); } \
+		if ((mask)& PROBE_N(5)) { stm32_configgpio(PROBE_5); } \
+		if ((mask)& PROBE_N(6)) { stm32_configgpio(PROBE_6); } \
+		if ((mask)& PROBE_N(7)) { stm32_configgpio(PROBE_7); } \
+		if ((mask)& PROBE_N(8)) { stm32_configgpio(PROBE_8); } \
+		if ((mask)& PROBE_N(9)) { stm32_configgpio(PROBE_9); } \
+	} while(0)
+
+# define PROBE(n,s)  do {stm32_gpiowrite(PROBE_##n,(s));}while(0)
+# define PROBE_MARK(n) PROBE(n,false);PROBE(n,true)
+#else
+# define PROBE_INIT(mask)
+# define PROBE(n,s)
+# define PROBE_MARK(n)
+#endif
+
+#endif  /*__NUTTX_CONFIG_MATEKH743SLIM_INCLUDE_BOARD_H  */

boards/matek/h743-mini/nuttx-config/include/board_dma_map.h

@@ -1,6 +1,6 @@
 /****************************************************************************
  *
- *   Copyright (C) 2019 PX4 Development Team. All rights reserved.
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
  * modification, are permitted provided that the following conditions
@@ -31,15 +31,13 @@
  *
  ****************************************************************************/
 
-#include <gtest/gtest.h>
-#include <AngularVelocityControl.hpp>
+#pragma once
 
-using namespace matrix;
+// DMAMUX1
+#define DMAMAP_SPI1_RX    DMAMAP_DMA12_SPI1RX_0 /* DMA1:37 */
+#define DMAMAP_SPI1_TX    DMAMAP_DMA12_SPI1TX_0 /* DMA1:38 */
 
-TEST(AngularVelocityControlTest, AllZeroCase)
-{
-	AngularVelocityControl control;
-	control.update(Vector3f(), Vector3f(), Vector3f(), 0.f, false);
-	Vector3f torque = control.getTorqueSetpoint();
-	EXPECT_EQ(torque, Vector3f());
-}
+
+// DMAMUX2
+#define DMAMAP_SPI4_RX    DMAMAP_DMA12_SPI4RX_1 /* DMA2:83 */
+#define DMAMAP_SPI4_TX    DMAMAP_DMA12_SPI4TX_1 /* DMA2:84 */

boards/matek/h743-mini/nuttx-config/nsh/defconfig

@@ -0,0 +1,247 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_MMCSD_HAVE_CARDDETECT is not set
+# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
+# CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_MMCSD_SPI is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/matek/h743-mini/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743VI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=512
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_DCACHE=y
+CONFIG_ARMV7M_DTCM=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARDCTL=y
+CONFIG_BOARD_CRASHDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=95150
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BUILTIN=y
+CONFIG_C99_BOOL8=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_PRODUCTID=0x0036
+CONFIG_CDCACM_PRODUCTSTR="MatekH743-mini"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x1B8C
+CONFIG_CDCACM_VENDORSTR="Matek"
+CONFIG_CLOCK_MONOTONIC=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_MEMFAULT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MODCMDS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
+CONFIG_DEV_PIPE_SIZE=70
+CONFIG_EXPERIMENTAL=y
+CONFIG_FAT_DMAMEMORY=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_LFN_ALIAS_HASH=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_BINFS=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FATTIME=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
+CONFIG_FS_PROCFS_MAX_TASKS=64
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MMCSD=y
+CONFIG_MMCSD_SDIO=y
+CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y
+CONFIG_MM_REGIONS=4
+CONFIG_NAME_MAX=40
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_STRERROR=y
+CONFIG_NSH_VARS=y
+CONFIG_OTG_ID_GPIO_DISABLE=y
+CONFIG_PIPES=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_RTC_DATETIME=y
+CONFIG_LIBC_MAX_EXITFUNS=1
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_LPWORKPRIORITY=50
+CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_WAITPID=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SDMMC1_SDIO_PULLUP=y
+CONFIG_SEM_PREALLOCHOLDERS=32
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STM32H7_ADC1=y
+CONFIG_STM32H7_ADC3=y
+CONFIG_STM32H7_BBSRAM=y
+CONFIG_STM32H7_BBSRAM_FILES=5
+CONFIG_STM32H7_BDMA=y
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_DMACAPABLE=y
+CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
+CONFIG_STM32H7_I2C1=y
+CONFIG_STM32H7_I2C2=y
+CONFIG_STM32H7_I2C_DYNTIMEO=y
+CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_RTC=y
+CONFIG_STM32H7_RTC_HSECLOCK=y
+CONFIG_STM32H7_RTC_MAGIC_REG=1
+CONFIG_STM32H7_SAVE_CRASHDUMP=y
+CONFIG_STM32H7_SDMMC1=y
+CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_SPI1=y
+CONFIG_STM32H7_SPI1_DMA=y
+CONFIG_STM32H7_SPI1_DMA_BUFFER=2048
+CONFIG_STM32H7_SPI2=y
+CONFIG_STM32H7_SPI3=y
+CONFIG_STM32H7_SPI4=y
+CONFIG_STM32H7_SPI4_DMA=y
+CONFIG_STM32H7_SPI4_DMA_BUFFER=2048
+CONFIG_STM32H7_SPI_DMA=y
+CONFIG_STM32H7_SPI_DMATHRESHOLD=8
+CONFIG_STM32H7_TIM15=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_TIM2=y
+CONFIG_STM32H7_TIM4=y
+CONFIG_STM32H7_TIM5=y
+CONFIG_STM32H7_TIM8=y
+CONFIG_STM32H7_UART4=y
+CONFIG_STM32H7_UART7=y
+CONFIG_STM32H7_UART8=y
+CONFIG_STM32H7_USART1=y
+CONFIG_STM32H7_USART2=y
+CONFIG_STM32H7_USART3=y
+CONFIG_STM32H7_USART6=y
+CONFIG_STM32H7_USART_BREAKS=y
+CONFIG_STM32H7_USART_INVERT=y
+CONFIG_STM32H7_USART_SINGLEWIRE=y
+CONFIG_STM32H7_USART_SWAP=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_UART4_BAUD=57600
+CONFIG_UART4_RXBUFSIZE=600
+CONFIG_UART4_TXBUFSIZE=1500
+CONFIG_UART7_BAUD=57600
+CONFIG_UART7_IFLOWCONTROL=y
+CONFIG_UART7_OFLOWCONTROL=y
+CONFIG_UART7_RXBUFSIZE=600
+CONFIG_UART7_TXBUFSIZE=1500
+CONFIG_UART8_BAUD=57600
+CONFIG_UART8_RXBUFSIZE=600
+CONFIG_UART8_TXBUFSIZE=1500
+CONFIG_USART1_BAUD=57600
+CONFIG_USART1_RXBUFSIZE=600
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USART1_TXBUFSIZE=1500
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_TXBUFSIZE=1500
+CONFIG_USART3_BAUD=57600
+CONFIG_USART3_RXBUFSIZE=600
+CONFIG_USART3_TXBUFSIZE=1500
+CONFIG_USART6_BAUD=57600
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_INIT_STACKSIZE=2944
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_WATCHDOG=y

boards/matek/h743-mini/nuttx-config/scripts/bootloader_script.ld

@@ -0,0 +1,213 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2019 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The Durandal-v1 uses an STM32H743II has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743II, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The Durandal has a Swtich on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the swiutch is
+ * drepresed, then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743ZI also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	flash (rx)  : ORIGIN = 0x08000000, LENGTH = 2048K
+	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
+	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
+	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
+	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
+	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
+	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/matek/h743-mini/nuttx-config/scripts/script.ld

@@ -0,0 +1,228 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2020 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The board uses an STM32H743II and has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743II, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * There's a switch on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the switch is
+ * drepresed, then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743ZI also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	ITCM_RAM  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	FLASH      (rx) : ORIGIN = 0x08020000, LENGTH = 1920K
+
+	DTCM1_RAM (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	DTCM2_RAM (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	AXI_SRAM  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K /* D1 domain AXI bus */
+	SRAM1     (rwx) : ORIGIN = 0x30000000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM2     (rwx) : ORIGIN = 0x30020000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM3     (rwx) : ORIGIN = 0x30040000, LENGTH =   32K /* D2 domain AHB bus */
+	SRAM4     (rwx) : ORIGIN = 0x38000000, LENGTH =   64K /* D3 domain */
+	BKPRAM    (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > FLASH
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > FLASH
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > FLASH
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > FLASH
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+
+		/* Pad out last section as the STM32H7 Flash write size is 256 bits. 32 bytes */
+		. = ALIGN(16);
+		FILL(0xffff)
+		. += 16;
+	} > AXI_SRAM AT > FLASH  = 0xffff
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > AXI_SRAM
+
+	/* Emit the the D3 power domain section for locating BDMA data */
+
+	.sram4_reserve (NOLOAD) :
+	{
+		*(.sram4)
+		. = ALIGN(4);
+		_sram4_heap_start = ABSOLUTE(.);
+	} > SRAM4
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/matek/h743-mini/src/CMakeLists.txt

@@ -0,0 +1,68 @@
+############################################################################
+#
+#   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+if("${PX4_BOARD_LABEL}" STREQUAL  "bootloader")
+	add_library(drivers_board
+		bootloader_main.c
+		usb.c
+	)
+	target_link_libraries(drivers_board
+		PRIVATE
+			nuttx_arch
+			nuttx_drivers
+			bootloader
+	)
+	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common)
+
+else()
+	add_library(drivers_board
+		i2c.cpp
+		init.c
+		led.c
+		sdio.c
+		spi.cpp
+		timer_config.cpp
+		usb.c
+	)
+	add_dependencies(drivers_board arch_board_hw_info)
+
+	target_link_libraries(drivers_board
+		PRIVATE
+			arch_io_pins
+			arch_spi
+			arch_board_hw_info
+			drivers__led
+			nuttx_arch
+			nuttx_drivers
+			px4_layer
+	)
+endif()

boards/matek/h743-mini/src/board_config.h

@@ -0,0 +1,236 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * Board internal definitions
+ */
+
+#pragma once
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+#include <stm32_gpio.h>
+
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+
+// #define FLASH_BASED_PARAMS
+
+
+/* LEDs are driven with push open drain to support Anode to 5V or 3.3V */
+
+#define GPIO_nLED_BLUE          /* PE3 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
+#define GPIO_nLED_GREEN         /* PE4 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
+
+#define BOARD_HAS_CONTROL_STATUS_LEDS   1
+#define BOARD_ARMED_STATE_LED           1 // Green LED
+#define BOARD_OVERLOAD_LED              0 // Blue LED
+
+
+/*
+ * ADC channels
+ *
+ * These are the channel numbers of the ADCs of the microcontroller that
+ * can be used by the Px4 Firmware in the adc driver
+ */
+
+/* ADC defines to be used in sensors.cpp to read from a particular channel */
+#define ADC1_CH(n)                  (n)
+
+/* Define GPIO pins used as ADC N.B. Channel numbers must match below  */
+#define PX4_ADC_GPIO  \
+	/* PC0  */  GPIO_ADC123_INP10, \
+	/* PC1  */  GPIO_ADC123_INP11, \
+	/* PA4  */  GPIO_ADC12_INP18, \
+	/* PA7  */  GPIO_ADC12_INP7, \
+	/* PC4  */  GPIO_ADC12_INP4, \
+	/* PC5  */  GPIO_ADC12_INP8
+
+/* Define Channel numbers must match above GPIO pin IN(n)*/
+#define ADC_BATTERY_VOLTAGE_CHANNEL     /* PC0  */  ADC1_CH(10)
+#define ADC_BATTERY_CURRENT_CHANNEL     /* PC1  */  ADC1_CH(11)
+#define ADC_BATTERY2_VOLTAGE_CHANNEL    /* PA4  */  ADC1_CH(18)
+#define ADC_BATTERY2_CURRENT_CHANNEL    /* PA7  */  ADC1_CH(7)
+#define ADC_AIRSPEED_IN_CHANNEL         /* PC4  */  ADC1_CH(4)
+#define ADC_RSSI_IN_CHANNEL             /* PC5  */  ADC1_CH(8)
+
+#define ADC_CHANNELS \
+	((1 << ADC_BATTERY_VOLTAGE_CHANNEL) | \
+	 (1 << ADC_BATTERY_CURRENT_CHANNEL) | \
+	 (1 << ADC_BATTERY2_VOLTAGE_CHANNEL) | \
+	 (1 << ADC_BATTERY2_CURRENT_CHANNEL) | \
+	 (1 << ADC_AIRSPEED_IN_CHANNEL) | \
+	 (1 << ADC_RSSI_IN_CHANNEL))
+
+
+/* Define Battery 1 Voltage Divider and A per V
+ */
+
+#define BOARD_BATTERY1_V_DIV         (11.0f)     /* measured with the provided PM board */
+#define BOARD_BATTERY1_A_PER_V       (40.0f)
+#define BOARD_BATTERY2_V_DIV         (11.0f)     /* measured with the provided PM board */
+
+
+/* CAN Silence
+ *
+ * Silent mode control \ ESC Mux select
+ */
+
+#define GPIO_CAN1_SILENT_S0  /* PD3  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN3)
+
+
+/* PWM
+ */
+#define DIRECT_PWM_OUTPUT_CHANNELS   12
+#define DIRECT_INPUT_TIMER_CHANNELS  12
+
+#define BOARD_HAS_PWM  DIRECT_PWM_OUTPUT_CHANNELS
+
+
+/* Spare GPIO */
+
+// #define GPIO_PG6                        /* PG6  */  (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTG|GPIO_PIN6)
+// #define GPIO_PD15                       /* PD15 */  (GPIO_INPUT|GPIO_FLOAT|GPIO_PORTD|GPIO_PIN15)
+// #define GPIO_PG15                       /* PG15 */  (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTG|GPIO_PIN15)
+
+
+/* Tone alarm output */
+
+#define GPIO_TONE_ALARM_IDLE    /* PA15 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN15)
+#define GPIO_TONE_ALARM_GPIO    /* PA15 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN15)
+
+// #define TONE_ALARM_TIMER        2  /* Timer 2 */
+// #define TONE_ALARM_CHANNEL      1  /* PA15 GPIO_TIM2_CH1OUT_2 */
+// #define GPIO_TONE_ALARM_IDLE    /* PA15 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN15)
+// #define GPIO_TONE_ALARM         GPIO_TIM2_CH1OUT_2
+
+
+/* USB OTG FS
+ *
+ * PE2  OTG_FS_VBUS VBUS sensing
+ */
+
+#define GPIO_OTGFS_VBUS         /* PE2 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTE|GPIO_PIN2)
+
+
+/* High-resolution timer */
+#define HRT_TIMER               2  /* use timer8 for the HRT */
+#define HRT_TIMER_CHANNEL       1  /* use capture/compare channel 3 */
+
+
+/* RC Serial port */
+#define RC_SERIAL_PORT          "/dev/ttyS4"
+
+// #define GPIO_RSSI_IN            /* PC5  */ (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN5)
+
+
+/* SD Card */
+#define SDIO_SLOTNO             0  /* Only one slot */
+#define SDIO_MINOR              0
+
+/* This board provides a DMA pool and APIs */
+#define BOARD_DMA_ALLOC_POOL_SIZE 5120
+
+/* This board provides the board_on_reset interface */
+#define BOARD_HAS_ON_RESET 1
+
+
+#define PX4_GPIO_INIT_LIST { \
+		PX4_ADC_GPIO, \
+		GPIO_CAN1_TX, \
+		GPIO_CAN1_RX, \
+		GPIO_CAN1_SILENT_S0, \
+		GPIO_nLED_BLUE, \
+		GPIO_nLED_GREEN, \
+		GPIO_TONE_ALARM_IDLE, \
+	}
+
+#define BOARD_ENABLE_CONSOLE_BUFFER
+
+#define BOARD_NUM_IO_TIMERS 4
+
+
+__BEGIN_DECLS
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void);
+
+/****************************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the board.
+ *
+ ****************************************************************************************************/
+
+extern void stm32_spiinitialize(void);
+
+extern void stm32_usbinitialize(void);
+
+extern void board_peripheral_reset(int ms);
+
+#include <px4_platform_common/board_common.h>
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS

boards/matek/h743-mini/src/bootloader_main.c

@@ -0,0 +1,75 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file bootloader_main.c
+ *
+ * FMU-specific early startup code for bootloader
+*/
+
+#include "board_config.h"
+#include "bl.h"
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+#include <px4_platform_common/init.h>
+
+extern int sercon_main(int c, char **argv);
+
+__EXPORT void board_on_reset(int status) {}
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+}
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	return 0;
+}
+
+void board_late_initialize(void)
+{
+	sercon_main(0, NULL);
+}
+
+extern void sys_tick_handler(void);
+void board_timerhook(void)
+{
+	sys_tick_handler();
+}

boards/matek/h743-mini/src/hw_config.h

@@ -0,0 +1,135 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+/****************************************************************************
+ * 10-8--2016:
+ *  To simplify the ripple effect on the tools, we will be using
+ *  /dev/serial/by-id/<asterisk>PX4<asterisk> to locate PX4 devices. Therefore
+ *  moving forward all Bootloaders must contain the prefix "PX4 BL "
+ *  in the USBDEVICESTRING
+ *  This Change will be made in an upcoming BL release
+ ****************************************************************************/
+/*
+ * Define usage to configure a bootloader
+ *
+ *
+ * Constant                example          Usage
+ * APP_LOAD_ADDRESS     0x08004000            - The address in Linker Script, where the app fw is org-ed
+ * BOOTLOADER_DELAY     5000                  - Ms to wait while under USB pwr or bootloader request
+ * BOARD_FMUV2
+ * INTERFACE_USB        1                     - (Optional) Scan and use the USB interface for bootloading
+ * INTERFACE_USART      1                     - (Optional) Scan and use the Serial interface for bootloading
+ * USBDEVICESTRING      "PX4 BL FMU v2.x"     - USB id string
+ * USBPRODUCTID         0x0011                - PID Should match defconfig
+ * BOOT_DELAY_ADDRESS   0x000001a0            - (Optional) From the linker script from Linker Script to get a custom
+ *                                               delay provided by an APP FW
+ * BOARD_TYPE           9                     - Must match .prototype boad_id
+ * _FLASH_KBYTES        (*(uint16_t *)0x1fff7a22) - Run time flash size detection
+ * BOARD_FLASH_SECTORS  ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector
+ * BOARD_FLASH_SECTORS   11                   - Hard coded zero based last sector
+ * BOARD_FLASH_SIZE     (_FLASH_KBYTES*1024)-   Total Flash size of device, determined at run time.
+ *                         (1024 * 1024)      - Hard coded Total Flash of device - The bootloader and app reserved will be deducted
+ *                                              programmatically
+ *
+ * BOARD_FIRST_FLASH_SECTOR_TO_ERASE  2        - Optional sectors index in the flash_sectors table  (F4 only), to begin erasing.
+ *                                               This is to allow sectors to be reserved for app fw usage. That will NOT be erased
+ *                                               during a FW upgrade.
+ *                                               The default is 0, and selects the first sector to be erased, as the 0th entry in the
+ *                                               flash_sectors table. Which is the second physical sector of FLASH in the device.
+ *                                               The first physical sector of FLASH is used by the bootloader, and is not defined
+ *                                               in the table.
+ *
+ * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus
+ *                                                                        BOOTLOADER_RESERVATION_SIZE  will be deducted from
+ *                                                                        BOARD_FLASH_SIZE to determine the size of the App FW
+ *                                                                        and hence the address space of FLASH to erase and program.
+ * USBMFGSTRING            "PX4 AP"            - Optional USB MFG string (default is '3D Robotics' if not defined.)
+ * SERIAL_BREAK_DETECT_DISABLED                -  Optional prevent break selection on Serial port from entering or staying in BL
+ *
+ * * Other defines are somewhat self explanatory.
+ */
+
+/* Boot device selection list*/
+#define USB0_DEV       0x01
+#define SERIAL0_DEV    0x02
+#define SERIAL1_DEV    0x04
+
+#define APP_LOAD_ADDRESS               0x08020000
+#define BOOTLOADER_DELAY               5000
+#define INTERFACE_USB                  1
+#define INTERFACE_USB_CONFIG           "/dev/ttyACM0"
+#define BOARD_VBUS                     MK_GPIO_INPUT(GPIO_OTGFS_VBUS)
+
+//#define USE_VBUS_PULL_DOWN
+#define INTERFACE_USART                1
+#define INTERFACE_USART_CONFIG         "/dev/ttyS0,57600"
+#define BOOT_DELAY_ADDRESS             0x000001a0
+#define BOARD_TYPE                     139
+#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
+#define BOARD_FLASH_SECTORS            (15)
+#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)
+
+#define OSC_FREQ                       8
+
+#define BOARD_PIN_LED_ACTIVITY         GPIO_nLED_BLUE // BLUE
+#define BOARD_PIN_LED_BOOTLOADER       GPIO_nLED_GREEN // GREEN
+#define BOARD_LED_ON                   0
+#define BOARD_LED_OFF                  1
+
+#define SERIAL_BREAK_DETECT_DISABLED   1
+
+#if !defined(ARCH_SN_MAX_LENGTH)
+# define ARCH_SN_MAX_LENGTH 12
+#endif
+
+#if !defined(APP_RESERVATION_SIZE)
+#  define APP_RESERVATION_SIZE 0
+#endif
+
+#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE)
+#  define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1
+#endif
+
+#if !defined(USB_DATA_ALIGN)
+# define USB_DATA_ALIGN
+#endif
+
+#ifndef BOOT_DEVICES_SELECTION
+#  define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#ifndef BOOT_DEVICES_FILTER_ONUSB
+#  define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif

boards/matek/h743-mini/src/i2c.cpp

@@ -0,0 +1,39 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/i2c_hw_description.h>
+
+constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
+	initI2CBusExternal(1),
+	initI2CBusInternal(2),
+};

boards/matek/h743-mini/src/init.c

@@ -0,0 +1,182 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file init.c
+ *
+ * FMU-specific early startup code. This file implements the
+ * board_app_initialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialisation.
+ */
+
+#include "board_config.h"
+
+#include <syslog.h>
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_board_led.h>
+#include <systemlib/px4_macros.h>
+#include <px4_arch/io_timer.h>
+#include <px4_platform_common/init.h>
+#include <px4_platform/gpio.h>
+#include <px4_platform/board_dma_alloc.h>
+
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+__END_DECLS
+
+/************************************************************************************
+ * Name: board_peripheral_reset
+ *
+ * Description:
+ *
+ ************************************************************************************/
+__EXPORT void board_peripheral_reset(int ms)
+{
+	UNUSED(ms);
+}
+
+/************************************************************************************
+ * Name: board_on_reset
+ *
+ * Description:
+ * Optionally provided function called on entry to board_system_reset
+ * It should perform any house keeping prior to the rest.
+ *
+ * status - 1 if resetting to boot loader
+ *          0 if just resetting
+ *
+ ************************************************************************************/
+__EXPORT void board_on_reset(int status)
+{
+	for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) {
+		px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i)));
+	}
+
+	if (status >= 0) {
+		up_mdelay(6);
+	}
+}
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* Reset PWM first thing */
+	board_on_reset(-1);
+
+	/* configure LEDs */
+	board_autoled_initialize();
+
+	/* configure pins */
+	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
+	px4_gpio_init(gpio, arraySize(gpio));
+
+	/* configure SPI interfaces */
+	stm32_spiinitialize();
+
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+
+}
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX;
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	/* Need hrt running before using the ADC */
+	px4_platform_init();
+
+	/* configure the DMA allocator */
+	if (board_dma_alloc_init() < 0) {
+		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
+	}
+
+	/* initial LED state */
+	drv_led_start();
+	led_off(LED_RED);
+	led_off(LED_BLUE);
+
+	if (board_hardfault_init(2, true) != 0) {
+		led_on(LED_BLUE);
+	}
+
+#ifdef CONFIG_MMCSD
+	int ret = stm32_sdio_initialize();
+
+	if (ret != OK) {
+		led_on(LED_BLUE);
+		return ret;
+	}
+
+#endif
+
+	/* Configure the HW based on the manifest */
+	px4_platform_configure();
+
+	return OK;
+}

boards/matek/h743-mini/src/led.c

@@ -0,0 +1,112 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file led.c
+ *
+ * LED backend.
+ */
+
+#include <px4_platform_common/px4_config.h>
+
+#include <stdbool.h>
+
+#include "chip.h"
+#include "stm32_gpio.h"
+#include "board_config.h"
+
+#include <nuttx/board.h>
+#include <arch/board/board.h>
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+extern void led_toggle(int led);
+__END_DECLS
+
+#  define xlat(p) (p)
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_BLUE,        // Indexed by LED_BLUE (defaulted to an output)
+	GPIO_nLED_GREEN
+};
+
+__EXPORT void led_init(void)
+{
+	/* Configure LED GPIOs for output */
+	for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
+		if (g_ledmap[l] != 0) {
+			stm32_configgpio(g_ledmap[l]);
+		}
+	}
+}
+
+static void phy_set_led(int led, bool state)
+{
+	/* Drive Low to switch on */
+	if (g_ledmap[led] != 0) {
+		stm32_gpiowrite(g_ledmap[led], !state);
+	}
+}
+
+static bool phy_get_led(int led)
+{
+	/* If Low it is on */
+	if (g_ledmap[led] != 0) {
+		return !stm32_gpioread(g_ledmap[led]);
+	}
+
+	return false;
+}
+
+__EXPORT void led_on(int led)
+{
+	phy_set_led(xlat(led), true);
+}
+
+__EXPORT void led_off(int led)
+{
+	phy_set_led(xlat(led), false);
+}
+
+__EXPORT void led_toggle(int led)
+{
+	phy_set_led(xlat(led), !phy_get_led(xlat(led)));
+}

boards/matek/h743-mini/src/sdio.c

@@ -0,0 +1,177 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+#include <board_config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+
+#include "chip.h"
+#include "board_config.h"
+#include "stm32_gpio.h"
+#include "stm32_sdmmc.h"
+
+#ifdef CONFIG_MMCSD
+
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Card detections requires card support and a card detection GPIO */
+
+#define HAVE_NCD   1
+#if !defined(GPIO_SDMMC1_NCD)
+#  undef HAVE_NCD
+#endif
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+static FAR struct sdio_dev_s *sdio_dev;
+#ifdef HAVE_NCD
+static bool g_sd_inserted = 0xff; /* Impossible value */
+#endif
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_ncd_interrupt
+ *
+ * Description:
+ *   Card detect interrupt handler.
+ *
+ ****************************************************************************/
+
+#ifdef HAVE_NCD
+static int stm32_ncd_interrupt(int irq, FAR void *context)
+{
+	bool present;
+
+	present = !stm32_gpioread(GPIO_SDMMC1_NCD);
+
+	if (sdio_dev && present != g_sd_inserted) {
+		sdio_mediachange(sdio_dev, present);
+		g_sd_inserted = present;
+	}
+
+	return OK;
+}
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void)
+{
+	int ret;
+
+#ifdef HAVE_NCD
+	/* Card detect */
+
+	bool cd_status;
+
+	/* Configure the card detect GPIO */
+
+	stm32_configgpio(GPIO_SDMMC1_NCD);
+
+	/* Register an interrupt handler for the card detect pin */
+
+	stm32_gpiosetevent(GPIO_SDMMC1_NCD, true, true, true, stm32_ncd_interrupt);
+#endif
+
+	/* Mount the SDIO-based MMC/SD block driver */
+	/* First, get an instance of the SDIO interface */
+
+	finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO);
+
+	sdio_dev = sdio_initialize(SDIO_SLOTNO);
+
+	if (!sdio_dev) {
+		syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", SDIO_SLOTNO);
+		return -ENODEV;
+	}
+
+	/* Now bind the SDIO interface to the MMC/SD driver */
+
+	finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR);
+
+	ret = mmcsd_slotinitialize(SDIO_MINOR, sdio_dev);
+
+	if (ret != OK) {
+		syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
+		return ret;
+	}
+
+	finfo("Successfully bound SDIO to the MMC/SD driver\n");
+
+#ifdef HAVE_NCD
+	/* Use SD card detect pin to check if a card is g_sd_inserted */
+
+	cd_status = !stm32_gpioread(GPIO_SDMMC1_NCD);
+	finfo("Card detect : %d\n", cd_status);
+
+	sdio_mediachange(sdio_dev, cd_status);
+#else
+	/* Assume that the SD card is inserted.  What choice do we have? */
+
+	sdio_mediachange(sdio_dev, true);
+#endif
+
+	return OK;
+}
+
+#endif /* CONFIG_MMCSD */

boards/matek/h743-mini/src/spi.cpp

@@ -0,0 +1,56 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/spi_hw_description.h>
+#include <drivers/drv_sensor.h>
+#include <nuttx/spi/spi.h>
+
+
+constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = {
+	initSPIBus(SPI::Bus::SPI1, {
+		initSPIDevice(DRV_IMU_DEVTYPE_MPU6000, SPI::CS{GPIO::PortC, GPIO::Pin15}, SPI::DRDY{GPIO::PortB, GPIO::Pin2}),
+	}),
+	initSPIBus(SPI::Bus::SPI2, {
+		initSPIDevice(DRV_OSD_DEVTYPE_ATXXXX, SPI::CS{GPIO::PortB, GPIO::Pin12}),
+	}),
+	initSPIBusExternal(SPI::Bus::SPI3, {
+		initSPIConfigExternal(SPI::CS{GPIO::PortD, GPIO::Pin4}),
+		initSPIConfigExternal(SPI::CS{GPIO::PortE, GPIO::Pin2}),
+	}),
+	initSPIBus(SPI::Bus::SPI4, {
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM42605, SPI::CS{GPIO::PortC, GPIO::Pin13}),
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM20602, SPI::CS{GPIO::PortE, GPIO::Pin11}),
+	}),
+};
+
+static constexpr bool unused = validateSPIConfig(px4_spi_buses);

boards/matek/h743-mini/src/timer_config.cpp

@@ -0,0 +1,82 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/io_timer_hw_description.h>
+
+constexpr io_timers_t io_timers[MAX_IO_TIMERS] = {
+	initIOTimer(Timer::Timer3, DMA{DMA::Index1, DMA::Stream2, DMA::Channel5}),
+	initIOTimer(Timer::Timer5, DMA{DMA::Index1, DMA::Stream0, DMA::Channel6}),
+	initIOTimer(Timer::Timer4, DMA{DMA::Index1, DMA::Stream6, DMA::Channel2}),
+	initIOTimer(Timer::Timer15),
+};
+
+constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel3}, {GPIO::PortB, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel4}, {GPIO::PortB, GPIO::Pin1}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel1}, {GPIO::PortA, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel2}, {GPIO::PortA, GPIO::Pin1}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel3}, {GPIO::PortA, GPIO::Pin2}),
+	initIOTimerChannel(io_timers, {Timer::Timer5, Timer::Channel4}, {GPIO::PortA, GPIO::Pin3}),
+	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel1}, {GPIO::PortD, GPIO::Pin12}),
+	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel2}, {GPIO::PortD, GPIO::Pin13}),
+	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel3}, {GPIO::PortD, GPIO::Pin14}),
+	initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel4}, {GPIO::PortD, GPIO::Pin15}),
+	initIOTimerChannel(io_timers, {Timer::Timer15, Timer::Channel1}, {GPIO::PortE, GPIO::Pin5}),
+	initIOTimerChannel(io_timers, {Timer::Timer15, Timer::Channel2}, {GPIO::PortE, GPIO::Pin6}),
+};
+
+constexpr io_timers_channel_mapping_t io_timers_channel_mapping =
+	initIOTimerChannelMapping(io_timers, timer_io_channels);
+
+
+
+constexpr io_timers_t led_pwm_timers[MAX_LED_TIMERS] = {
+	initIOTimer(Timer::Timer1),
+};
+
+// #define CCER_C1_NUM_BITS   4
+// #define POLARITY(c)    (GTIM_CCER_CC1P << (((c)-1) * CCER_C1_NUM_BITS))
+// #define DRIVE_TYPE(p)  ((p)|GPIO_OPENDRAIN|GPIO_PULLUP)
+
+// static inline constexpr timer_io_channels_t initIOTimerChannelLED(const io_timers_t io_timers_conf[MAX_LED_TIMERS],
+// 		Timer::TimerChannel timer, GPIO::GPIOPin pin, int ui_polarity)
+// {
+// 	timer_io_channels_t ret = initIOTimerChannel(io_timers_conf, timer, pin);
+// 	ret.gpio_out = DRIVE_TYPE(ret.gpio_out);
+// 	ret.masks = POLARITY(ui_polarity);
+// 	return ret;
+// }
+
+// constexpr timer_io_channels_t led_pwm_channels[MAX_TIMER_LED_CHANNELS] = {
+// 	initIOTimerChannelLED(led_pwm_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortA, GPIO::Pin8}, 1),
+// };

boards/matek/h743-mini/src/usb.c

@@ -1,6 +1,6 @@
 /****************************************************************************
  *
- *   Copyright (c) 2013-2019 PX4 Development Team. All rights reserved.
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
  * modification, are permitted provided that the following conditions
@@ -32,78 +32,47 @@
  ****************************************************************************/
 
 /**
- * @file vehicle_model_params.c
- * Parameters for vehicle model.
+ * @file usb.c
  *
- * @author Julien Lecoeur <julien.lecoeur@gmail.com>
+ * Board-specific USB functions.
  */
 
-/**
- * Mass
- *
- * @unit kg
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_MASS, 1.f);
+#include "board_config.h"
+#include <nuttx/usb/usbdev.h>
+#include <nuttx/usb/usbdev_trace.h>
+#include <stm32_otg.h>
+#include <debug.h>
 
-/**
- * Inertia matrix, XX component
+/************************************************************************************
+ * Name: stm32_usbinitialize
  *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_XX, 0.01f);
+ * Description:
+ *   Called to setup USB-related GPIO pins for the board.
+ *
+ ************************************************************************************/
 
-/**
- * Inertia matrix, YY component
- *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_YY, 0.01f);
+__EXPORT void stm32_usbinitialize(void)
+{
+	/* The OTG FS has an internal soft pull-up */
 
-/**
- * Inertia matrix, ZZ component
- *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_ZZ, 0.01f);
+	/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
 
-/**
- * Inertia matrix, XY component
- *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_XY, 0.f);
+#ifdef CONFIG_STM32F7_OTGFS
+	stm32_configgpio(GPIO_OTGFS_VBUS);
+#endif
+}
 
-/**
- * Inertia matrix, XZ component
+/************************************************************************************
+ * Name:  stm32_usbsuspend
  *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_XZ, 0.f);
-
-/**
- * Inertia matrix, YZ component
+ * Description:
+ *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
+ *   used.  This function is called whenever the USB enters or leaves suspend mode.
+ *   This is an opportunity for the board logic to shutdown clocks, power, etc.
+ *   while the USB is suspended.
  *
- * @unit kg m^2
- * @decimal 5
- * @increment 0.00001
- * @group Vehicle Model
- */
-PARAM_DEFINE_FLOAT(VM_INERTIA_YZ, 0.f);
+ ************************************************************************************/
+__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
+{
+	uinfo("resume: %d\n", resume);
+}

boards/matek/h743-slim/bootloader.px4board

@@ -0,0 +1,3 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ROMFSROOT=""