* init: working towards dual-action ATMOS
* fix: update gz sim to latest
* fix: add motor number max fitting Actuator
* fix: revert non-necessary changes
* fix: ensure esc count does not exceed maximum number of ESCs
* feat: update gz to latest, includes ATMOS dual action
* fix: restore dds_topics
* fix: update gazebo model commit
Add PWM_*_CENTERx for each servo.
Use a bilinear transform to map actuator_servos to PWM signals.
This solution only works for PWM based servos. Other types of servos are not affected.
* PWM: Add servo trim option
* PWM: Improve documentation of PWM trim feature
* PWM: cleaner clamping and docs typo
* update documentation & safety
* add migration formula
* rename param from trim to center
* docs with center instead of trim
* move clamping and reorder values
* improve documentation
* adress failing range check
* improve documentation
* CA: add event for setting CENTER with TRIM
Signed-off-by: Silvan <silvan@auterion.com>
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: Silvan <silvan@auterion.com>
Barometeric pressure was changed to the SI unit Pascal instead of the non-SI unit Hectopascal/Millibar in
0c31f6389666d942d59b74cd2e107a5d3b263ea6
This script stayed unchanged and suffers from assuming `sensor_baro.pressure` is still in the old unit which would be a 100 times smaller number.
Changed ASCII command from ASCII #127 to ASCII #8
Good: Changed ASCII command from ASCII #127 to ASCII #8
Reported-by: jsm09a <https://github.com/jsm09a>
Signed-off-by: Siri <sriramj2@hotmail.com>
nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* always reschedule from measurementReadyCallback, don't update range mode is processMeasurement fails, reschedule trigger faster if Argus_TriggerMeasurement fails, refactor mode switching logic, update perf counters
* make format
* make format exclude microstrain submodule
---------
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* feat: configurable board pwm freq from Kconfig
* feat: add board_pwm_config to submenu
* fix: define sequence correction
* fix: revert Tools/simulation/gz
* fix: track upstream gz
* fix: track upstream mavlink
* feat: adjustable pwm for multiple board types
* feat: add conditional check for CONFIG_ for correct fallback
* add: spacecraft board with correct BOARD_PWM_FREQ supporting 10Hz actuation rate
* fix: set dependencies for submenu arch chips
* fix: keep only upper arch level
* fix: proper checking - still not showing up for board config
* feat: add hidden kconfig for platforms
* Merge Nuttx config into px4board
Allows to expose nuttx into PX4 if needed
* Kconfig: Include nuttx symbols in updateconfig
Only if applicable i.e. defined in the kconfig
* fix: merged config with previously generated boardconfig
* doc: updated code comment
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
From https://github.com/google/fuzztest.
This will now also add gtest (via cmake FetchContent)
And requires newer cmake (container updates):
CMake 3.19 or higher is required. You are running version 3.16.3
if [ "x$PRT_GPS1_" = "x" ]; then
^-----------^ SC2268 (style): Avoid x-prefix in comparisons as it no longer serves a purpose.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Note: Some files are autogenerated and I did not yet
go through each source of generation to fix it there.
Instead I adjusted the filter to only exclude those
such that we can fix things in steps.
