nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* always reschedule from measurementReadyCallback, don't update range mode is processMeasurement fails, reschedule trigger faster if Argus_TriggerMeasurement fails, refactor mode switching logic, update perf counters
* make format
* make format exclude microstrain submodule
---------
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* feat: configurable board pwm freq from Kconfig
* feat: add board_pwm_config to submenu
* fix: define sequence correction
* fix: revert Tools/simulation/gz
* fix: track upstream gz
* fix: track upstream mavlink
* feat: adjustable pwm for multiple board types
* feat: add conditional check for CONFIG_ for correct fallback
* add: spacecraft board with correct BOARD_PWM_FREQ supporting 10Hz actuation rate
* fix: set dependencies for submenu arch chips
* fix: keep only upper arch level
* fix: proper checking - still not showing up for board config
* feat: add hidden kconfig for platforms
* Merge Nuttx config into px4board
Allows to expose nuttx into PX4 if needed
* Kconfig: Include nuttx symbols in updateconfig
Only if applicable i.e. defined in the kconfig
* fix: merged config with previously generated boardconfig
* doc: updated code comment
---------
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
From https://github.com/google/fuzztest.
This will now also add gtest (via cmake FetchContent)
And requires newer cmake (container updates):
CMake 3.19 or higher is required. You are running version 3.16.3
if [ "x$PRT_GPS1_" = "x" ]; then
^-----------^ SC2268 (style): Avoid x-prefix in comparisons as it no longer serves a purpose.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Note: Some files are autogenerated and I did not yet
go through each source of generation to fix it there.
Instead I adjusted the filter to only exclude those
such that we can fix things in steps.
* gz_plugins: add MovingPlatformController
This plugin moves the entity to which it is attached to simulate moving
platforms (boats, trucks, ...) to takeoff and land on. Updates
Tools/simulation/gz submodule with corresponding dependency. Use with:
PX4_GZ_MODEL_POSE=0,0,2.2,0,0,0 PX4_GZ_WORLD=moving_platform make px4_sitl gz_standard_vtol
more in README.md
* MovingPlatformController: Wrench implementation
Now it works by applying appropriate forces & torques to make the
platform move as desired. Compared to the previous velocity-based
version it introduces no kinematic constraints, keeping it realistic.
Other updates:
- Also make heading configurable by env var in addition to velocity
- Cleaner error handling (runtime error, gzerr, gzwarn)
- Read parameters (gravity, platform mass & height) from model rather than hardcoding
- Update README with new env vars, usage in sdf, etc.
* MovingPlatformController: fix warning message
* MovingPlatformController: fix build
https://github.com/PX4/PX4-Autopilot/pull/24518 changed some variable
names in CMakeLists. This adapts ours to use the new ones.
* MovingPlatformController: format
* MovingPlatformController: address code review
From feedback on PR
- Parameterise low pass filters with cutoff frequency (rather than
filter coefficient directly).
- Add comment with units of feedback gains.
- Scale attitude gains with platform inertia (rather than mass).
Additionally
- Wait 5 seconds before moving the platform so the model has time to
spawn (was quicker before rebasing...)
- Refactor: separate noise generation and force/torque calculation into
two separate functions
- rename updatePlatformState -> getPlatformState to emphasise
difference from other update* functions that update internal state only
- remove unused gz transport node
- README grammar
* MovingPlatformController: format
* MovingPlatformController: remove redundant call
* MovingPlatformController: clarify explanation
* MovingPlatformController: clarify & comment units
* MovingPlatformController: wait for model to spawn
Rather than waiting a fixed 5s, we now only move the platform once the
model is spawned.
For that we construct the model name from the relevant environment
variables, in the same way as done in px4-rc.gzsim.
If attaching to an existing model, do not wait.
* MovingPlatformController: correct substring extraction
---------
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Added the board configs for encryption, I had to disable smbus and px4 io in the arkv6x
* Added the key generator script
* Added the decryptor, logs are needed for it though
* Added the log download and modified the decryptor
* Quick fixes & README
* Additional modifications & cleanup
* Tested upd connection
Adjusted the log downloader to handle multiple entry responses from the FC
Edited README
* Reverted IP address change
* Added pycryptodome to the requirements.txt
* fixes for log download and decryption
* Removed old log decryptors and updated README
* Pointed the ark borads to the dummy key updated the README accordingly
* Adjusted the folders in README, removed new lines
* Extended command line arguments for all possibilities for description
* Added MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES after heartbeat received to make sure log request is answered in all cases
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Edited README, changed the serial connection logic and updated logdownload, made decryption a bit easier to understand
* Update Tools/log_encryption/README.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Removed new lines
* arkv6x: add individual mags to default.px4board
---------
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Co-authored-by: Alex Klimaj <alex@arkelectron.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Sriram Kanagalingham