So transitions between stopped/not stopped respect the slew rate.
- Remove previous stopped motor handling in publish_actuator_controls
- Replace with handle_stopped_motors, called in Run() before slew
- Introduce ApplyNanToActuators in ControlAllocation to stop
- Refactor ice shedding slightly to fit new structure
In the CA_ICE_PERIOD param description, a '>' was at the start of a
line. This is interpredeted by markdown as a quotation type indented
block which applies not only to that line, but to all following ones.
Changing the line breaks to only occur after full stops fixes it.
* FWModeManager: add option to set flag for disabling actuators during launch
Signed-off-by: Silvan <silvan@auterion.com>
* Allocation: add option to each control surface to be locked for launch
Signed-off-by: Silvan <silvan@auterion.com>
* FW rate control: reset integral while control surfaces are locked
Signed-off-by: Silvan <silvan@auterion.com>
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: mahima-yoga <mahima@auterion.com>
* feat: implement UAVCAN LED control for individual light control and assignment
* uavcan led: nit-picks from review
* uavcan led: reduce maximum number of lights
to avoid unused parameters
* uavcan led: simplify anticolision on check
* uavcan led: correctly map 8-bit RGB to rgb565
* Trim param name character arrays to 17
16 characters + \0 termination
* uavcan led: final nit-picks
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
This feature periodically spins the unused motors on VTOL airframes, to
break off ice that has built up in the motor while it is still feasible
to do so. Each ice shedding event sends a motor ouput of 0.01 to the
unused motors for 2 seconds.
Configured by `CA_ICE_PERIOD`, the duration of the entire cycle. Set to
0 to disable.
Add PWM_*_CENTERx for each servo.
Use a bilinear transform to map actuator_servos to PWM signals.
This solution only works for PWM based servos. Other types of servos are not affected.
* PWM: Add servo trim option
* PWM: Improve documentation of PWM trim feature
* PWM: cleaner clamping and docs typo
* update documentation & safety
* add migration formula
* rename param from trim to center
* docs with center instead of trim
* move clamping and reorder values
* improve documentation
* adress failing range check
* improve documentation
* CA: add event for setting CENTER with TRIM
Signed-off-by: Silvan <silvan@auterion.com>
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: Silvan <silvan@auterion.com>
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* feat: spacecraft tooling for commander and VehicleStatus
* feat: spacecraft tooling for commander and VehicleStatus
* fix: format
* fix: format
* fix: remove iostream
* fix: remove iostream
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* boards: Increase TELEM2 rx buffer size for DDS over serial use-case (ARK Jetson)
feat: spacecraft tooling for commander and VehicleStatus
fix: format
fix: remove iostream
feat: mavlink compliant spacecraft definition
* feat: add orbiter to define
* feat: add orbiter to define
* fix: change mav_type to new spacecraft orbiter enum value
* fix: build issue
* feat: update mavlink
* feat: update mavlink to latest master with spacecraft
* feat: update mavlink
* feat: update mavlink to latest
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: removed unnecessary definition
* fix: format
* feat: cmake variant for spacecraft
* feat: proper mav_type and rc init
* fix: removed dart from build system
* add: thrusters to actuator type
* rft: reordering actuator type
* rft: initial merging of controllers for spacecraft vehicles
* feat: rate controller nominal
* fix: format
* feat: spacecraft attitude control and minor refactoring of params
* feat: add position controller
* fix: format
* fix: moved trajectories to new message, removed derivative filters
* fix: format
* fix: removed extra newline
* fix: spacecraft allocation builds
* feat: add thrusters to effectivenes, add spacecraft build to cmake, clean comments
* feat: required changes for allocation
* feat: thruster simulation interface
* fix: update maximum and minimums
* fix: format
* fix: added newline at the end of spacecraft actuator effectiveness
* feat: configurable board pwm freq from Kconfig
* feat: add orbiter to define
* feat: cleanup and synchronization with new mavlink vehicle definition
* fix: get away without specifying spacecraft vehicle
* fix: conflicts
* fix: format
* fix: remove duplicate entry
* rft: remove Kconfig changes
* rft: revert main Kconfig
* rft: revert main kcoonfig on platforms
* rft: remove changes to board PWm (go on another PR)
* rft: revert changes to commander (main is correct)
* fix: extra char on commander_helper
* rft: removed extra spaces
* rft: moved effectiveness to spacecraft
* fix: spacecraft effectiveness
* fix: extra space
* feat: preliminary version, still using thrusters
* rft: initial pipeline on PX4 side with rotors instead of thrusters
* feat: add atmos model
* feat: spacecraft with rotor pipeline tested, working
* feat: update gz
* rft: removed thruster interfaces
* fix: format
* fix: remove control allocation
* fix: thruster normalization
* fix: format
* fix: nuttx version
* fix: clang tidy error
* feat: updated gz to add atmos model
* fix: update gz
* fix: update mavlink
* fix: remove friend class from allocation lib
* fix: remove actuator_outputs/motors
---------
Co-authored-by: Alexander Lerach <alexander@auterion.com>
* Remove more circular dependencies with ActuatorEffectiveness
* Separate vehicle specific actuator effectiveness
Keep actuator effectivenss in control allocator
* Remove test dependency for now
* Group library directories
Fix
* Change directory names
* Rebase fix
fix: ControlAllocator float and int comparison bug
There was an incorrect comparison between a float variable `dt` and a `uint64_t` value representing 5 milliseconds (`5_ms`). As a result, `do_update` could never become true even if the last torque setpoint was received more than 5 milliseconds before.
To solve this, the `5_ms` value has been converted to seconds (0.005f) for the comparison with `dt`.
