- add unit tests for adsb conflict detection
- move adsb conflict detection to lib/adsb and adsb conflict class
- use containers/Array.hpp for buffer array
- expand fake_traffic
This adds a parser for Unicore sentences sent in-between NMEA sentences.
This brings support for the Unicore UM982 module which publishes heading
information based on the two antennas.
Signed-off-by: Julian Oes <julian@oes.ch>
It turns out that when you rotate by 45 degrees, as required on the
CubeOrange+, then you can easily get into clipping because the vector
components are constrained after the rotation. In order to avoid that,
we have to avoid getting close to the int16 range and switch from 20 bit
resolution to 16bit resolution earlier.
Signed-off-by: Julian Oes <julian@oes.ch>
- remove deprecated actuator_controls[INDEX_FLAPS/SPOILERS/AIRBRAKES]
- use new topic normalized_unsigned_setpoint.msg (with instances flaps_setpoint
and spoilers_setpoint) to pass into control allocation
- remove flaps/spoiler related fields from attitude_setpoint topic
- CA: add possibility to map flaps/spoilers to any control surface
- move flaps/spoiler pitch trimming to CA (previously called DTRIM_FLAPS/SPOILER)
- move manual flaps/spoiler handling from rate to attitude controller
FW Position controller: change how negative switch readings are intepreted
for flaps/spoilers (considered negative as 0).
VTOL: Rework spoiler publishing in hover
- pushlish spoiler_setpoint.msg in the VTOL module if in hover
- also set spoilers to land configuration if in Descend mode
Allocation: add slew rate limit of 0.5 to flaps/spoilers configuration change
Instead of doing the flaps/spoilers slew rate limiting in the FW Position Controller
(which then only is applied in Auto flight), do it consistently over all flight
modes, so also for manual modes.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- remove deprecated actuator_controls[INDEX_LANDING_GEAR]
- remove dead code in mc rate controller that used to prevent it from being retracted
on the ground (anyway had no effect as it only affected the actuator_control[LANDING_GEAR]
which wasn't sent to the control allocation)
- for VTOLs handle deployment/retraction of landing gear in AUTO as a MC (retract if
more than 2m above ground, deploy if WP is a landing WP), plus additionally when transition
flight task is called (ALTITUDE mode and higher)
- for FW in AUTO: add logic in FW Position Controller, depending on waypoint type mainly
- manual landing gear settings always come through (a manual command overrides a previous
auto command, and vice-versa)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Tiltrotor_extra_controls also contains collective thrust beside collective tilt, as passing a 3D
thrust setpoint vector beside the tilt is not feasible.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- always publish esc_status
- when enabled via MODAL_IO_VLOG param, enable actuator debug output
- for modal_io commands, use ESC HW ID values instead of motor number for easier use
- publish esc_status message for command line commands
- Uncommented the code that fills in the cmdcount and power fields in the esc_status topic
---------
Co-authored-by: Travis Bottalico <travis@modalai.com>
- Switching to the first order filter that was previously
only in FlightTaskManualAltitude.
- Moving the scaling of full stick deflection to
radians per second into the class.
* RTL: only do calculations in is-inactive if global position is recent
* RTL: refactor calcRtlTimeEstimate to only calc and not pub
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
