- this doesn't currently change anything, but gets us ready to start
experimenting with using the small amount of instruction tightly memory
on STM32F7
- the .ramfuncs section works with NuttX CONFIG_ARCH_RAMFUNCS
- mag enabled with -M when starting
- always check FIFO count before transfer
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_MAG_DEVTYPE_MPU9250 -> DRV_MAG_DEVTYPE_AK8963
- always check FIFO count before transfer even with data ready
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- change default FIFO empty rate to 1 kHz (consistent with other drivers)
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- check interupt status and FIFO count as part of full transfer and reset or adjust timing if necessary
- change default FIFO empty rate to 1 kHz (consistent with other drivers)
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- check interupt status and FIFO count as part of full transfer and reset or adjust timing if necessary
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_IMU_DEVTYPE_ICM20608 -> DRV_IMU_DEVTYPE_ICM20608G
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
This is another new InvenSense sensor with max output data rate of 32 kHz (both accel & gyro), on board anti-aliasing filter, and accel range 32G. Overall quite similar to the ICM-42688-P added in #14420, but with doubled accel range and without the optional high resolution output or clock sync.
This is a new InvenSense sensor with max output data rate of 32 kHz (both accel & gyro), on board anti-aliasing filter, optional higher resolution output (18 bit accel, 19 bit gyro), and clock sync.
- ecl/attitude_fw was never maintained as a standalone library
- moving ecl/attitude_fw library into the fw_att_control module to ease further development
* uORB orb_stat() and update(uint64_t *time, void *dst) are now obsolete and have been deleted
* mavlink messages add more advertised checks in streams get_size() check to improve data rate calculation across different scenarios
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Running the sensors module out of the same WQ thread as the estimator, position, and attitude controllers is a bit safer and prevents potential priority and starvation issues. There is a very small increase in latency (~50 us) between sensors and ekf2 execution (on average). This also saves a little bit of memory (~ 3 kB) and cpu (~1-1.5% depending on the board).
- nuttx in PX4/Firmware (b7a83e23c5e50896bb137266cf89ff928dfaae42): https://github.com/PX4/NuttX/commit/d509b1edd736cb7db509a9c86e7ffcde10c4fd45
- nuttx current upstream: https://github.com/PX4/NuttX/commit/bf646dcf46ac4a18c29b1cab4aa5e7a54280782e
- Changes: https://github.com/PX4/NuttX/compare/d509b1edd736cb7db509a9c86e7ffcde10c4fd45...bf646dcf46ac4a18c29b1cab4aa5e7a54280782e
bf646dcf46 2020-03-03 Daniel Agar - [BACKPORT] stm32h7: spi_exchange (no dma) available with CONFIG_STM32H7_SPI_DMATHRESHOLD
f2a7ef0ade 2020-03-03 Daniel Agar - [BACKPORT] stm32f7: spi_exchange (no dma) available with CONFIG_STM32F7_SPI_DMATHRESHOLD
7ffc59ba3d 2020-03-03 Daniel Agar - [BACKPORT] stm32: spi_exchange (no dma) available with CONFIG_STM32_SPI_DMATHRESHOLD
d1c8fdb5fb 2020-03-02 Daniel Agar - [BACKPORT] arm/stm32h7 add STM32H7_SPI_DMATHRESHOLD
fa8d636118 2020-03-02 Daniel Agar - [BACKPORT] stm32f76xx77xx_dma.h fix DMAMAP_SPI2_RX_2/DMAMAP_SPI2_TX_2
762d80b217 2020-03-02 Daniel Agar - [BACKPORT] arm/stm32f7 add STM32F7_SPI_DMATHRESHOLD
4f4bbbbf1c 2020-03-02 Daniel Agar - [BACKPORT] arm/stm32 add STM32_SPI_DMATHRESHOLD
Co-authored-by: PX4 Build Bot <bot@px4.io>
Daniel Agar