The ADC peripheral can only support up to
50MHz on rev V silicon and 36MHz on Y silicon.
The existing driver always used no prescaler
and kept boost setting at 0.
A board can optionaly define RC_SERIAL_SWAP_USING_SINGLEWIRE
If the board is wired board with TX to the input (Swapped) and
the SoC does not support U[S]ART level RX-TX swapping to allow
useing onewire to do the swap if and only if:
RC_SERIAL_SWAP_USING_SINGLEWIRE is defined
RC_SERIAL_SWAP_RXTX is defined
TIOCSSWAP is defined and retuns !OK
TIOCSSINGLEWIRE is defined
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
imxrt:117x Reuse all but io_timer_hw_description and imxrt_pinirq.c
imxrt:ADC & LPADC bifurcation and restructuring
imxrt:hrt support Up to GPT6
nxp/rt117x:adc Corrected
c23b72dffe [BACKPORT] sched/semaphore: Remove restriction to use nxsem_trywait from ISR
fd47cd20a2 [BACKPORT] imxrt:Serial Preserve all but W1C bit in SR
c55f0fd3ac [BACKPORT] imxrt: lpspi dma invalidate cache after exchange
198c7caecb [BACKPORT] imxrt:lpi2c fix status handeling & race
cbd2e44c10 [BACKPORT] s32k3xx: lpspi dma invalidate cache after exchange
e71618d60e [BACKPORT] s32k3xx:lpi2c fix status handeling & race
6f59cc3659 [BACKPORT] s32k1xx:lpi2c fix status handeling & race
1e316d7e32 [BACKPORT] imxrt: flexcan use hpwork for receiving frames
67c1c59865 [BACKPORT] net/can can_readahead_timestamp always free iob
8be831a4ff [BACKPORT] imxrt: fix txdeadline add ecc/fd support
00a68b7668 [BACKPORT] fs/cromfs: Fix faulty DEBUGASSERT() check
d5cf545d6e [BACKPORT] S32K3XX EMAC MCAST support Fix compile warning when ioctl is not enabled
4265c830fa [BACKPORT] imxrt:edma {s|d}last needs to be total xfer size
24b4d44896 [BACKPORT] s32k3xx:edma {s|d}last needs to be total xfer size
eed0482f64 [BACKPORT] s32k1xx:edma {s|d}last needs to be total xfer size
36aab4146a [BACKPORT] kinetis:edma {s|d}last needs to be total xfer size
a0faf31f6f [BACKPORT] arch/stm32f7: fixes for pinmap
eb8255121d [BACKPORT] stm32h7:sdmmc It is not an error if no wait was needed
062044fe41 [BACKPORT] board nucleo-h743zi:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
e03f9d3917 [BACKPORT] board olimexino-stm32:Rework board.h not use CONFIG_STM32_USE_LEGACY_PINMAP
4c3a467415 [BACKPORT] stm32l5:pinmap Add suffix to all pins and add legacy pinmap
153069ed40 [BACKPORT] stm32wb:pinmap Add suffix to all pins and add legacy pinmap
d84d737f89 [BACKPORT] stm32f0l0g0:stm32f0{3|5|7|9}x_pinmap & stm32g0_pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
5fc7071ac1 [BACKPORT] stm32l4:stm32l4x{3|4|5|6|r}xx_pinmap pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
20061c2aab [BACKPORT] stm32:stm32f10{0|2|3{c|r|v|z}|5{r|v}|7v}_pinmap refactor
4d1f83d484 [BACKPORT] stm32:stm32l15xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
2dfa3f2601 [BACKPORT] stm32:stm32g4xx{c|k|r|m|v|q} pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d206327809 [BACKPORT] stm32:stm32f3{0|3|7}xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
95e66ab508 [BACKPORT] stm32:stm32f20xxx pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
d2fd9178ad [BACKPORT] stm32:f4/f412 pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
a9df45166d [BACKPORT] stm32f7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
07dd2b424e [BACKPORT] stm32h7:pinmap Remove GPIO_SPEED_xxx and add legacy pinmap
1e3065344f [BACKPORT] stm32u5:stm32u585xx_pinmap Fix typo
0a05365a90 [BACKPORT] stm32wl5:pinmap Fix typo
e3834138dc [BACKPORT] tools:Add STM32 Pin migration tool
df851a8768 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h also for stm32h7x7xx
d75dfcf1e9 [BACKPORT] stm32h7/rcc: make VOS0 configurable from board.h
963f35f4fc [BACKPORT] {stm32,stm32f7,stm32h7,stm32l4,efm32}/otg: rasie an assertion if IN request is not possible to transfer
de2fcc6668 [BACKPORT] {stm32f7,stm32h7,stm32l4}/sdmmc: callback support requires HPWORK
6929144fc2 [BACKPORT] stm32h7/otgdev: FS transceiver must be enabled if OTGFS enabled
a2078afaea [BACKPORT] stm32h7/otg: add support for external ULPI
26e1246c86 [BACKPORT] stm32h7/rcc: OTGHS ULPI works only in VOS0
cd6daa185e [BACKPORT] stm32h7: update ULPI pins
c73c261ae3 [BACKPORT] arch/boards: fix stm32f411-mininum:nsh compilation failure after enabling IRQMONITOR
8078f134ef [BACKPORT] arch/stm32/stm32.h: do not include stm32_usbdev.h if not supported
60e884fa92 [BACKPORT] {stm32,stm32l4,stm32f0l0g0}/otg: move STM32_NENDPOINTS definitions to header files
dda297cb78 [BACKPORT] arch/arm/src/stm32/hardware: Fix register define
362b976b0e [BACKPORT] arch/arm/src/stm32/hardware: Add stm32g4 rcc apb1 timer enable compatibility
434fd71f2c [BACKPORT] {stm32/stm32l4/stm32f7/stm32h7/efm32}/otgdev: remove invalid use of the priv field for EP
2476d24e8c [BACKPORT] {stm32f7,stm32h7}/otg: fix compilation for USBDEV when USB_DEBUG=y
eb43c582ea [BACKPORT] drivers/mtd/ramtron: change nsectors size to uint32
20f61ff0d5 [BACKPORT] fs/littlefs: add full support for LittleFS block device cfg in Kconfig
60471fbf8c [BACKPORT] drivers/mtd: add Kconfig options for RAMTRON emulated page & sector size
David Sidrane