- publish wind estimate only from EKF, and wind speeds from airspeed selector to new separate topic (airspeed_wind)
- rename message wind_estimate to wind
- publish wind from currently used ekf instance (ekf2selector)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- new heater_status logging message
- run continously at low rate until configured sensor is found
- fix px4io fd bugs (fd open/close/ioctl must be same thread)
- currently the main change is that it reduces the max number of ORB multi instances to 4, but usage will be expanded as needed
- limits number of EKF2 multi instances to 2.
- enabled on all cortex m4 boards
- control allocation module with multirotor, VTOL standard, and tiltrotor support
- angular_velocity_controller
- See https://github.com/PX4/PX4-Autopilot/pull/13351 for details
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Roman Bapst <bapstroman@gmail.com>
- parameter updates can be quite expensive because they trigger nearly all modules to reload all of their parameters immediately
- limit modules from updating faster than once per second
- handle saving the mag bias per sensor (across all estimator instances using that mag) in sensors/vehicle_magnetometer
- this is now saving back to the actual mag calibration CAL_MAGn_OFF{X,Y,Z}
- ekf2 reset mag mag bias on any magnetometer or calibration change
- use Kalman filter scheme to update stored mag bias parameters using all available bias estimates for that sensor
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- log all estimator (ekf2) flags as separate booleans in a new dedicated low rate message (only publishes at 1 Hz or immediately on any change)
- this is a bit verbose, but it avoids the duplicate bit definitions we currently have across PX4 msgs, ecl analysis script, flight review, and many other custom tools and it's much easier for casual log review in FlightPlot, PlotJuggler, csv, etc
- for compatibility I've left estimator_status filter_fault_flags, innovation_check_flags, and solution_status_flags in place, but they can gradually be removed as tooling is updated
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
- split out switches from manual_control_setpoint into new message manual_control_switches
- manual_control_switches published at minimal rate (~ 1 Hz) or immediately on change
- simple switch debounce in rc_update (2 consecutive identical decodes required)
- manual_control_switches logged at full rate rather than sampled at (5-10% of messages logged)
- manual_control_setpoint publish at minimal rate unless changing
- commander handle landing gear switch for manual modes
- processing of mode_slot and mode_switch is now split so we only do one or the other (not both)
- a future step will be to finally drop mode_switch and accompanying switches entirely
Co-authored-by: Matthias Grob <maetugr@gmail.com>
- reset IMU bias on calibration change (only works with multi-ekf)
- standardize PX4_INFO/PX4_WARN/PX4_ERR output for multi-ekf with instance number
- https://github.com/PX4/PX4-ECL/pull/924
- saves a small amount of work for the ekf2 selector in multi-EKF mode (visual_odometry_aligned now ignored)
- helps to distinguish the origin/purpose from vehicle_odometry and vehicle_visual_odometry
- ekf2 can now run in multi-instance mode (currently up to 9 instances)
- in multi mode all estimates are published to alternate topics (eg estimator_attitude instead of vehicle_attitude)
- new ekf2 selector runs in multi-instance mode to monitor and compare all instances, selecting a primary (eg N x estimator_attitude => vehicle_attitude)
- sensors module accel & gyro inconsistency checks are now relative to the mean of all instances, rather than the current primary (when active ekf2 selector is responsible for choosing primary accel & gyro)
- existing consumers of estimator_status must check estimator_selector_status to select current primary instance status
- ekf2 single instance mode is still fully supported and the default
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- new sensors work item that subscribes to N x sensor_gps and publishes vehicle_gps_position
- blending is now configurable with SENS_GPS_MASK and SENS_GPS_TAU
Co-authored-by: Jacob Crabill <jacob@volans-i.com>
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
- inconsistency checks now run continuously instead of only preflight
- keep inconsistencies for all sensors
- add per sensor data validator state as overall health flag
- Nuttx only process all suspend & resume scheduling notes when top is running, otherwise only track IDLE
- convert cpuload and print load to c++
- delete unused fields from print_load struct
- update hrt_store_absolute_time (previous unused)
- log full sensor_combined by default for now
- small decrease to input_rc rate (manual_control_setpoint is no longer filtered)
- sensor_correction can be logged at full rate (low publication rate)
If some bits are set but no topic was added, _subscriptions was null but
later accessed.
During normal use this only happens when switching between different
firmware versions with different SDLOG_PROFILE definition (with custom
config).
- avoids the need for ekf2_timestamp publications by q and lpe
- adds logger to the lockstep cycle and makes it poll on ekf2_timestamps
or vehicle_attitude. This avoids dropped samples (required for replay).
