These changes remove the two code paths to updates (forceupdate and update) and try to reboot and bootload IO independent of its state, wether it is in bootloader mode already, safety switch is off or if it is in "nominal state" (running and safety on). This ensures that there are no conditions where user error or boot sequence can prevent a successful upgrade. The only state where an upgrade will not be done is if the system is fully armed.
This system command will display, set and save the network
settings.
netman show - Displays the current settings.
netman update - Will check for a net.cfg file on the SD card.
If present, it will update the paramaters,
delete the file, and reboot. Using the new settings.
netman save - Saves the current settings to net.cfg on the SD card.
This file shoulf be renamed to preserver it across
reboots or editited to chech networkin paramates.
File format is name<space>value:
echo DEVICE=eth0 > /fs/microsd/net.cfg
echo BOOTPROTO=fallback >> /fs/microsd/net.cfg
echo IPADDR=192.168.0.4 >> /fs/microsd/net.cfg
echo NETMASK=255.255.255.0 >>/fs/microsd/net.cfg
echo ROUTER=192.168.0.254 >>/fs/microsd/net.cfg
echo DNS=192.168.0.254 >>/fs/microsd/net.cfg
Valid values for `proto` are `dhcp`, `static`, `falback`
Both will try dhcp for CONFIG_NETINIT_FALLBACK times
and fall back to the static address.
NETMASK - is the network mask.
IPADDR - this nodes ip address for static or fall back.
ROUTER - The default route.
DNS - The address of the dns server.
- generate PWM_MAIN 1-14
- generate PWM_AUX 1-8
- generate PWM_EXTRA 1-8
- px4io and pwm_out directly read configuration parameters
- only available and active physical outputs are actually shown for configuration
- overall saves flash despite adding many new parameters
- add new parameter `IMU_GYRO_FFT_EN` to start
- add 75% overlap in buffer to increase FFT update rate
- space out FFT calls (no more than 1 per cycle)
- increase `IMU_GYRO_FFT_MIN` default
- decrease main stack usage
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
* [WIP] i2c_spi_buses: add '-q' for quiet startup flag
And enable for optional board sensors.
* ROMFS: rc.sensors try starting all optional I2C sensors quietly
Co-authored-by: Daniel Agar <daniel@agar.ca>
rc.io is called from 2 places in rc.interface:
- if [ $OUTPUT_MODE = io -o $OUTPUT_MODE = uavcan_esc ]:
- 'set OUTPUT_MODE io' is only set within USE_IO=yes, so removing
the check in rc.io has no effect.
- in case of UAVCAN, we also want the IO for RC, now covered in the next
case.
- Further down ('Start IO for RC input if needed.').
This is intended to start IO for RC only, when fmu is already started.
However the previous check '$USE_IO = yes' in rc.io prevented that.
In addition we don't start rc_input in case of $USE_IO = no.
Fixes no RC on Pixhawk 2 with SYS_USE_IO=0.
* parameter and logic to commander for triggering failsafe from external automatic trigger system.
* logic to startup script for enabling ATS. Added uORB publishing to pwm_input module.
* Refactored out CDev usage from pwm_input and ll40ls. Refactored out ll40ls specifics from pwm_input and cleaned up dead code.
-moved rc.mavlink to the boards optional rc additions (now it's called rc.board_mavlink) to handle board specific mavlink needs (mavlink over usb, ethernet, additional streams, etc.)
-mavlink module will be responsible to usb defaults, therefore less args are needed to be passed to mavlink module if one wants to use mavlink over usb.
-the way to check if connection is usb is by it's designated variable and not by config mode.
