* FMUv4pro : allow power monitoring for hipower rail
* FMUv4pro : init temperare calibration EEPROM CS
* FMUv4pro : workaround for safety switch
* FMUv4pro : remove useless and conflicting defines
* FMUv4pro : disable internal pull-up for OC sensing
/FAULT won't achieve VinputLow with internal pull-up resistor so it must
be turned off for both /VDD_5V_PERIPH_OC and /VDD_5V_HIPOWER_OC.
Replaced by external pull-up.
* FMUv4pro : correct safety switch handling
RC02 has a hardware pull-down on this signal
* Revert "FMUv4pro : workaround for safety switch"
This reverts commit 9528ae29b68700fa7c6604c1ac2756c7dac2819c.
This fixes the issue with initializing channels 5,6 without
channels 1-4.
The code assumed all timers actions were in order to be
initialized. This is not the case. This commit fixes that
bad assumption by not stopping the configuration on the
first action entry with a base == 0, but processing all
entries with non-zero base.
MPU9250 is mostly an MPU6500 with a mag (AK8963) in the same package.
Support driving MPU6500 with the MPU9250 driver. The id of the driver
isn't set differently since this way it allows to force a recalibration.
Ideally MPU9250 driver could even not exist and the support for these
sensors be merged back in the MPU6000 that's more complete. This is an
intermediate step in that direction.
- There's no I2C2, so remove it
- Fix alignments everywhere in board_config.h
- Clarify STM32 ADC (not available) and the ADC on the FGPA
- Fix format on some comments
FMUv4 PRO HW does not have a controlable V3.3 on the connector
it therefore can not support the SPEKTUM binding.
This PR removes the Power switch controls or binding control
interfaces from the board config
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate bindin
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_R
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Use the abstaction SPEKTRUM_POWER to enable the interface not
the define for the GPIO pin.
Removed the legacy FMUv4 define that was activating a nonexistent
pull up and on some HW driving the PPM_IN aka RC_IN aka SPEKTRUM_RX
to VDD.
Also detailed the connections of this pins for the board.
The simplest connection is RC_IN to a timer capture pin
and a UART.
In this case the UART_RX pin and just be left as is.
While the pin can be configured as the PPM_IN (Timer capture)
or as SPEKTRUM_RX_AS_GPIO_OUTPUT to use it as and GPIO to
facilitate binding.
Renamed the macros and defines to be more explicit as to what
Is being done and the sense of the parameters
Mohammed Kabir