* failure_injection: improve previously vague motor faulure
Reading it again I decided adding the sentance in 4d2170c13ea4d42c5b0b464dbbcbb68fb098cbcc is not clear enough.
* docs/safety: add a motor failure detection paragraph
The functionality is in my eyes pretty basic but so far completely undocumented so I went through the code and added a paragraph based on questions I received.
* Subedit
* Apply suggestion from @hamishwillee
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* rc_update: remove 1% deadzone for all channels
this should be handled higher level.
* Remove all references to the RC{n}_DZ parameters
Regular expression: RC.{0,2}_DZ
---------
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Remove support for MAVLink 1
* Add back support for MAVLink 1 but don't default to it
* Update src/modules/mavlink/mavlink_params.c
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
---------
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* ROMFS: do not exit airframe loading if SYS_AUTOSTART is 0
Do not treat 0 as a magic value that skips the aiframe loading.
Instead leave it tot he rc.autostart to load an airframe that if finds
appropriate (can be defined in external aiframe).
Signed-off-by: Silvan <silvan@auterion.com>
* ROMFS: adjust airframe load spacing and message/comment wording
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: Silvan <silvan@auterion.com>
During a mission the last waypoint is often a LAND. If the previous waypoint is not directly above the land waypoint the offtrack calculation is incorrect. This regression was introduced when the offtrack calculation switched from 2D to 3D.
* Fix formatting and capitalization in dev_env_mac.md
Updated formatting and capitalization for consistency in the macOS development environment documentation.
* Correct 'Mac OS' to 'macOS' in documentation
* Fix capitalization of 'macOS' in documentation
Move ramvectors from DTCM to ITCM, this seems to better in general.
Also ITCM is marked as RO so is safer anyhow, now that DTCM is fully
unused we add DTCM region of 256kB to memory allocator. Increases usable
memory from 1536kB to 1792kB and decrease system load a bit since DTCM
is faster
* s32k3xx: EMIOS allow independent frequencies for each channel
* mr-canhubk3: update config
* mr-canhubk344: Fix adap board detect
* mr-canhubk344: Use LPSPI1 (Port P1A) for SD card
* airframes: Add B3RB Ackermann rover config
See https://nxp.gitbook.io/mr-b3rb for more information about the NXP
B3RB platform. PX4 Support basic control for now
* Tone down the performance of some runners from 8cpu+ down to 4cpu+
* Improve and document caching on PX4 builds with an improved ccache key strategy
* Review and document artifact upload logic for binaries uploaded to S3 and github
releases
* Future Improvement, introduce runners configuration file so we can
control more precesily which instances are allocated.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
The UARTs themselves were already present, just not configured under any
alias.
Follow [ArduPilot UART naming for this
board](https://ardupilot.org/plane/docs/common-pixracer-pro.html#default-uart-order),
out of necessity: it's the only combination that makes sense and is
understood by QGroundControl.
(For example, I've attempted configuring the additional UARTs as `_EXT1`
and `_EXT2`, but only `_EXT2` was understood by QGC.)
Trying to actually use the FrSky telemetry port for anything without
configuring FrSky telemetry on a different port may be impossible without
modifying the board's `init/rc.board_extras`.
(Should that script be modified to check if the port is used for
anything else?)
Skip naming the RC input port.
Fixes#21455.
Increases signal ampltiude on a 1Hz sin input until a target rate (R/P/Y = 0.8/0.5/0.5 rad/s) is reached. Identification signal is then scaled with this ampltitude instead of the user-defined parameter.
