* removed commented out parts
* changed the height controller to work in Altitude mode and moved the controller to the uuv_pos_control.hpp instead of uuv_att_control.hpp
* Updated format changes etc. Removed one parameter, that is not used anymore(UUV_HGT_MODE) added my correct email
* added a rotation to the thrust, that with different roll and pitch values, x y z thrust is still working as if roll/pitch is zero.
* fixed constant roll/pitch to be 0.0 again
* added parameter for maximum distance between controlled des height and current height.
Added state observation to reset the desired height to current height when altitude mode is turned on.
* added first short descriptions of manual modes.
* update descriptions
* removed vector dependency
* feat: updated gz submodule
* fix: newline
* fix: gz submodule
---------
Co-authored-by: Pedro Roque <roque@caltech.edu>
* Initial changes
* index fix
* gz index fix2
* gz index fix 3
* updates
* Run prettier
* zsh env
removed gz classic
* Corrections 2
* Cleanups
* Update docs/en/dev_setup/dev_env_mac.md
* Apply suggestions from code review
* Minor subedit and prettier
* small correction
* cleanups gz harmonic brew formula
* fix(macos.sh): invert px4-sim install condition for --sim-tools
The condition checked if px4-sim WAS installed before running
brew install, meaning it would never install on a fresh system.
Add the missing negation so it installs when NOT already present.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* docs: rewrite macOS dev environment setup guide
- Add Xcode Command Line Tools as prerequisite
- Default to ~/.zshrc (macOS default since Catalina)
- Explain why ulimit change is needed and why in startup file
- Add reminder to open new terminal after shell config changes
- Remove broken pip3 alias workaround
- Split git clone into clone + submodule update (canonical form)
- Recommend --sim-tools flag since first build uses gz_x500
- Document what macos.sh installs and its --reinstall flag
- Clarify Gazebo comes from --sim-tools / px4-sim formula
- Add XQuartz requirement for Gazebo display
- Add verification section with key tool checks and smoke test
- Remove outdated video guide comment block
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* conventions
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* FWModeManager: add option to set flag for disabling actuators during launch
Signed-off-by: Silvan <silvan@auterion.com>
* Allocation: add option to each control surface to be locked for launch
Signed-off-by: Silvan <silvan@auterion.com>
* FW rate control: reset integral while control surfaces are locked
Signed-off-by: Silvan <silvan@auterion.com>
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: mahima-yoga <mahima@auterion.com>
* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f274523349a029e63ab4462e41d0c1c
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* feat: implement UAVCAN LED control for individual light control and assignment
* uavcan led: nit-picks from review
* uavcan led: reduce maximum number of lights
to avoid unused parameters
* uavcan led: simplify anticolision on check
* uavcan led: correctly map 8-bit RGB to rgb565
* Trim param name character arrays to 17
16 characters + \0 termination
* uavcan led: final nit-picks
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
- Update "Failed to import Python packages" section to reference
gz_x500 instead of jmavsim, and point to Tools/setup/requirements.txt
instead of listing individual packages
- Fix :::info admonition spacing in Ubuntu dev env docs
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
The new px4-dev container replaces the old per-distro container
hierarchy from PX4/PX4-containers. It is:
- Multi-architecture (linux/amd64 + linux/arm64)
- Based on Ubuntu 24.04
- Built from the in-tree Dockerfile via GitHub Actions
- Published to both ghcr.io and Docker Hub
- Tagged with PX4 versions (e.g. px4-dev:v1.16.0)
Mark the legacy per-distro containers (px4-dev-nuttx-jammy,
px4-dev-ros2-humble, etc.) as deprecated, note that px4-sim
is planned for simulation workflows.
Update all examples to use px4-dev instead of legacy containers.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
docker.md:
- Update container hierarchy from focal to jammy
- Replace ROS Noetic/Foxy references with ROS 2 Humble
- Update docker run example to use humble container
- Update SITL example from gazebo-classic to gz_x500
- Update VM tested version from Ubuntu 14.04 to 22.04
vscode.md:
- Remove "Ubuntu 18.04" from inotify troubleshooting header
(this issue is not Ubuntu-version-specific)
dev_env_linux_centos.md:
- Update GCC warning to reference current Ubuntu LTS toolchain
instead of old Focal Docker file
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
- Replace "older version" collapsible with info block stating
supported versions: Ubuntu 24.04 (primary) and 22.04
- Remove Gazebo Classic references (Ubuntu 22.04 section, install step)
- Note that GCC version comes from Ubuntu package manager
- Clarify that GCC version depends on Ubuntu release
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
