There were a number of cases where the state was not correct or not as
desired after disarming, when running an external mode 'MyMission' with
executor:
- run MyMission, which triggers Hold, then Land
- before: Mode: Hold, executor_in_charge: 1
- after: Mode: MyMission, executor_in_charge: 1
- run MyMission, then user switches to RTL
- before: Mode: MyMission, executor_in_charge: 0
- after: Mode: MyMission, executor_in_charge: 1
- run MyMission, then while in Hold mode, low battery failsafe (RTL)
- before: Mode: Hold, executor_in_charge: 1
- after: Mode: MyMission, executor_in_charge: 1
- run MyMission, then stop external mode (terminate the process)
- before: Mode: (mode not available), executor_in_charge: 0
- after: Mode: Hold, executor_in_charge: 0
This case is unchanged:
- run MyMission, then low battery failsafe (RTL)
- before: Mode: MyMission, executor_in_charge: 1
- after: Mode: MyMission, executor_in_charge: 1
* MAV_CMD_REQUEST_MESSAGE support for MESSAGE_INTERVAL
* Default should be -1 for stream
* Format
---------
Co-authored-by: PX4BuildBot <bot@pixhawk.org>
nsh console running on USB
param module running
working with i2c and common drivers
provided implementation for drv_pwm_output.h
i2cdetect working as expected with no device
mavlink started succesfully
mounts sd card and logger runs
logger to file succesfully
pwm_servo implemented without using Nuttx lib
pwm_out outputs expected waveforms
- however currently if the frequency is higher than what the pwm_out
driver runs, there will be aliasing, based on how the registers gets
resets
wifi softap working
- Seeing wifi hotspot
- cant connect due to wrong password
- problems with adjusting ssid and password
wifi ssid and password being set accordinglu
connected to wifi hotspot with dhpcd
- made some changes to nuttx to only build for SoftAP mode, however this
was effectivelyy removing the ifdef for STATION mode. Should investigate
the coexist option again
added ifdef to not use timer 0 when wifi enabled
- reverted esp32 rt_timer to make use of timer 0 by default
fix setting incorrect bit in hrt timer register
- hrt running as expected, but on startup the pwm_out driver starts up
at about 200Hz and then rises over a minute or so 250Hz. Not sure if
this was present previously, and could be due to Wifi running at time
priority on timer 0
pull xtensa compilers in setup.ubuntu.sh
revert logger stacksize and cmake argument
esp32 chip revision and PX4 UUID implemented
spi board reset implemented, formatting checked
devkit acts on startup as a wifi bridge for comms
- the most usefull setting for the general developer when buying a esp32 devkit
- testing Mavlink shell using ./Tools/mavlink_shell.py
- todo: Test mavlink messages being forward
improve wifi telemetry by increasing prio
- Remove power save mode on wifi
- increased daemon thread schedule priority to 50
compiles without Nuttx changes
- updated compiler settings to match those of nuttx on px4 side
add espressif_esp32 to excluded boards
ci: allow docker to find xtensa compilers
* mavlink: add message spacing for AVAILABLE_MODES, for low bandwidth links
* calculate delay based on rate
* fixed transmit time calc & not delay single mode send
Co-authored-by: bkueng <beat-kueng@gmx.net>
---------
Co-authored-by: bkueng <beat-kueng@gmx.net>
- mavlink in PX4/Firmware (4acabda9cef8bfa6ea670672dddbc45d97276612): b27d03bffd
- mavlink current upstream: f9dbd8c496
- Changes: b27d03bffd...f9dbd8c496
f9dbd8c4 2025-08-14 Julian Oes - C example fixup (#2333)
e261db27 2025-08-14 Nick E - common.xml: Add COASTING flag to CAMERA_TRACKING_STATUS_FLAGS (#2326)
4f0efaaa 2025-08-14 Nick E - common.xml: Add "Power On" action to MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN command (#2329)
6a98757c 2025-08-14 vlad-serbanica - Add new component IDs for multiple radios (#2327)
2ca0cb55 2025-08-14 Nick E - common.xml: Add commands, capability and flag for Moving Target Indicators (MTI) (#2323)
115f1c83 2025-08-14 Christian Clauss - Typos: Run codespell on all files (#2328)
