Add an NSH command to format a device with littlefs, analogous to
mkfatfs for FAT filesystems. The command unmounts the mount point,
then remounts with forceformat to format and mount in one step.
Enable the command on boards that use littlefs as primary storage
(airbrainh743 and kakuteh7v2), and document it in the airbrainh743
flight controller page as a recovery procedure for a corrupted
flash filesystem.
Usage: mklittlefs /dev/mtd0 /fs/flash
* boards: corvon 743v1 support (Docs and LED alignment)
This PR addresses #24769 by providing the required official documentation, while simultaneously aligning the board's LED semantics entirely with the PX4 standard.
Key Changes:
- Add complete corvon 743v1 hardware documentation and manufacturer link.
- Fix LED out-of-bounds bug and strictly align RGB states to Pixhawk standard (LED_BLUE=0, LED_RED=1, LED_GREEN=3).
- Update bootloader pin config (hw_config.h) to use red LED for boot/error, and update pre-built bootloader.bin.
* Prettier and file reduce
* docs: address reviewer feedback & board ID fix
* Apply suggestion from @hamishwillee
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs: resolve final reviewer feedback (PPM, Debug Port, Manufacturer List)
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* Remove Zubax Orel - not available and no other presence
* Fix up zubax product links
* Snapdragon flight - delete as no longer relevant hardware
* Delete intel aero docs
* Brushless whoop - remove docs except for link to old version
* Many link fixes
Note: Some files are autogenerated and I did not yet
go through each source of generation to fix it there.
Instead I adjusted the filter to only exclude those
such that we can fix things in steps.
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
Julian Oes