As the sensor can directly report the amount of samples in the fifo, use it to simplify the logic.
Also combine the fifo empty/fifo overflow checks for interrupt and polling modes.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
If DRDY signal is used, the interrupt status needs to be cleared at FIFO reset
in order to make DRDY go back inactive. Otherwise there won't be a falling edge
interrupt at the next sample.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The size input argument for monocypher crypto_xchacha20_ctr should be the
plaintext message length.
The promise of the interface is, that the call to encrypt_data updates the
ciphertext message length after the call succeeds.
The crypto should check that the output buffer length (cipher length) is
large enough to contain the encrypted data.
Fix these issues; these have gone unnoticed for a long time since the interface
has been only used by logger, and passing the same size for both in and out.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This prevents accidental misconfiguration via I2C if there are
multiple SPI devices on the same bus. The device may hear it's i2c address
and write some register, while there is data transfer ongoing with another
device.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Fix a memory overflow in case SENS_BOARD_ROT is set to Rotation::ROTATION_MAX (41) which is not a valid value
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Maximum plaintext length was wrong, it is just k - 2 * hLen -2, where k is RSA key modulus length and hLen is hash length
Also minimum block that can be encrypted didn't make sense for RSA-OAEP, it is just 1 byte, the rest will be padded.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Bootloader needs to have a mechanism to de-initialize crypto, in case some HW accelerator
is being used. This adds the needed function for it
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For the esc_calibration code, the actuator test is published for each motor
in a row. If the orb queue size is too small, messages are lost and not
received in mixer_module.
Set the default orb queue size of ActuatorTest high enough to keep the commands
for all motors in the queue.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Include board_config.h for BOARD_GET_EXTERNAL_LOCKOUT_STATE etc. macros
- Include fcntl.h for "open"
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
It accesses kernel internal structures directly; this needs to be
worked out with some proper userspace-kernel interface
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is needed for DMA capable memory for fat also in the user side;
the file system doesn't seem to work reliably without.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For protected/kernel builds the cxx static initializations
needs to be done also in kernel side, since px4 creates
c++ objects in kernel
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Implement an interface for protected build to access parameters.
The implementation only does IOCTL calls to the kernel, where the parameters
live.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Put all functions which are commont to flat build and protected kernel and
userspace to an own source file
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a nuttx userspace interface for hrt driver, communicating with
the actual px4 hrt driver via BOARDCTL IOCTLs
This is be used when running PX4 in NuttX protected or kernel builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Move some logic from Subscriber into uORBManager. This reduces calls from the
modules to the uORB manager, improving performance in protected build.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
It was a mistake to mix these two together, it is simpler to implement the boardctl interface
for the protected build, if the boardctl ioctls are different
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds an ioctl interface for NuttX protected build, allowing
system calls from user space to kernel for uORB, HRT and crypto
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
When building uORB for NuttX flat build, or for some other target, everything
works as before.
When building uORB for NuttX protected or kernel build, this does the following:
- The kernel side uORB library reigsters a boardctl handler for calls from userspace
and services the boardctl_ioctls by calling the actual uORB functions
- For user mode binaries, the uORBManager acts as a proxy, making boardctl_ioctl calls to the
kernel side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This saves a lot of flash space, in case functions from libtomcrypt
are not used (currently only RSA related).
When RSA is not used, the linker can now drop all libtomcrypt related things.
This is especially relevant for bootloaders using the SW crypto.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The stackcheck build flash space overflows after adding hygrometers.
Also follow the naming convention of other similar config flags, and rename the
config.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Split the px4_layer into user and kernel space libraries. Add some stubs for
user-space (e.g. version) where an interface to the kernel needs to be added
Use posix-versions for cpuload.cpp and print_load.cpp for userspace; these link to nuttx internals. This functinality could be built on top of posix (e.g. procfs) interfaces
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
If the board supports encrypting logfiles, but the parameter SDCARD_ALGORITHM is set to NONE,
the log should be written to the sdcard in plaintext format. This fixes a bug which caused
logger to hang in mutex instead.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Don't link to px4_layer
- Don't link to flashparams; flashparams would work only in kernel side
- Add missing link to px4_platform
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This goes the other way around; arch_io_pins is using the pin
definitions from drivers_board, so the drivers_board needs to be linked
into arch_io_pins
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Since uORB is split into kernel and userspace parts, it is no longer possible to just
link uORB into px4_platform, which is used in both kernel and user side.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Define __KERNEL__ macro during compilation and place the module in separate library
Remove default library linking to m or libc on NuttX. Add these in platform layer instead, since
they are different on kernel and user side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The needed version specific things come from px4 layer. Since version
is used both in kernel an user sides in protected build, it can't directly
link to drivers_board
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For NuttX protected or kernel build, the prebuilds can't contain libraries which are
different for kernel and user-space in protected/kerenl builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Allocate and free the node name in uORBDeviceNode.
- Add protected build support by de-allocating the name with kmm_free, when
running in kernel side. strdup allocates from the kernel heap in NuttX kernel
space.
- Remove the CDev::unregister_driver_and_memory(), it is no longer used
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
In NuttX protected build there are separate work queues in kernel and user sides.
pthreads are only available in user side, so use tasks and kthreads for
memory protected builds.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Use the same memory allocation in sw_crypto driver as what is used in
src/lib/crypto libraries
In addition, in nuttx protected build, allocate all memory from kernel heap
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
There was an error that PX4_CRYPTO was cached accross variants, if it was
defined just for one variant.
This synchronizes the caching of BOARD_CRYPTO with other similar BOARD_ flags;
it is set as INTERNAL and "1" when enabled.
Also remove handling of BOARD_KEYSTORE; it is not used anywhere after
changing the crypto under src/drivers. If a separate keystore driver
is required, it is just selected as any other driver in px4board
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
It is possible to either set the keyfile locations in board configuration or
with the same environment variables as before.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is more logical place for the "backend" implementation than
directly under platform.
This also allows making other implementations as "real" drivers, as well as proper configuration via Kconfigs
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Don't compare pointers to metadata, but the metadata contents.
In protected/kernel build there are two sets of metadata, on on kernel
side and another in user side. Thus the comparison of pointers would just
always fail. Compare orb_id instead
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Proxy all calls to the DeviceNode through Manager;
- This hides the DeviceNode from publishers and subscribers
- Manager can be made an interface class between user and kernel spaces in protected build
- This doesn't increase code size or harm the performance on flat build
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
In protected build, this needs to go to user-space initialization as it
calls apps (sercon) and launches mavlink.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is already removed from nuttx, and in posix the size of s->last_times
can be just checked with sizeof()
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Jukka Laitinen