* drivers: disable INS by default
With the growing number of INS drivers some targets are running out of flash
and its becoming challenge to keep them under the limit.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Update boards/nxp/tropic-community/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update boards/px4/fmu-v6xrt/default.px4board
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
This resets the USARTs' clock source selection to the default, in case
it has been changed by the bootloader.
This is required if booting from the ArduPilot bootloader which happens
to reset the clock selection to PLL.
Without this fix, UARTs (including the console) is garbled, so
presumably at an invalid baudrate.
Having a generic interface over the GPS drivers makes dedicated
functionality for each driver harder. Move the Septentrio driver into
its own module under the `gnss` driver directory, and let it have its
own parameters for only the functionality it requires. This also helps
with adding new features because they only need to be implemented for
the driver that wants it, simplifying testing.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
- during casual testing on default configs the stack was penetration was reaching ~90% which is a bit too close for comfort
- increasing by 50% to be conservative
* Fixedwing rate control into a separate module
* Start fw_rate_control for vtol
* Move over airspeed related parameters to fw_rate_control
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Co-authored-by: David Sidrane <David.Sidrane@NscDg.com>
Co-authored-by: alexklimaj <alex@arkelectron.com>
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
