* Adds configurable I2C address for PCA9685 PWM driver
Introduces a parameter to set the I2C address for the PCA9685 PWM output driver, enhancing flexibility for hardware variations. Updates documentation and board initialization scripts to support the new configuration and streamline device startup.
* Update src/drivers/pca9685_pwm_out/module.yaml
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/drivers/pca9685_pwm_out/module.yaml
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
We should not build and release with the MAVLink development dialect
because messages in development.xml can change at any time and break
things.
Instead we should prototype and test things using specific mavlink-dev
targets.
- split up old module into two, one handling setpoint generation, one control
- add lateral and longitudinal control setpoints topics that can also be
injected from companion computer
- add configuration topics that (optionally) configure the controller
with limits and momentary settings
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* adis16507: enhance driver to handle and recover from all failure modes
- Clean up driver
- Add optional hardware reset
- Fix scale and range for 125 deg/s variant
- Handle communication errors when read returns zeroes
- Improved perf counters
* change prints to PX4_DEBUG, define BURST_READ_CMD, do both soft and hard reset, use ScheduleNow instead of 1ms delay, change read/write stall period to SPI_STALL value
* Added the board configs for encryption, I had to disable smbus and px4 io in the arkv6x
* Added the key generator script
* Added the decryptor, logs are needed for it though
* Added the log download and modified the decryptor
* Quick fixes & README
* Additional modifications & cleanup
* Tested upd connection
Adjusted the log downloader to handle multiple entry responses from the FC
Edited README
* Reverted IP address change
* Added pycryptodome to the requirements.txt
* fixes for log download and decryption
* Removed old log decryptors and updated README
* Pointed the ark borads to the dummy key updated the README accordingly
* Adjusted the folders in README, removed new lines
* Extended command line arguments for all possibilities for description
* Added MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES after heartbeat received to make sure log request is answered in all cases
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update Tools/log_encryption/README.md
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Edited README, changed the serial connection logic and updated logdownload, made decryption a bit easier to understand
* Update Tools/log_encryption/README.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Removed new lines
* arkv6x: add individual mags to default.px4board
---------
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Co-authored-by: Alex Klimaj <alex@arkelectron.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase max mission items for boards with >=1kb RAM to 1000
Signed-off-by: Silvan <silvan@auterion.com>
boards: increase NUM_MISSION_ITMES_SUPPORTED for SITL to 10000
Signed-off-by: Silvan <silvan@auterion.com>
* Bidirectional DShot
Co-authored-by: Julian Oes <julian@oes.ch>
* f4/f1 support, not supported
* fix f1 build target
* sanity check timer_channel value, fix CCxNP ifdef, debug stuff
* removed debug code, added define for H7 HAVE_GTIM_CCXNP
* round robin sampling for less than 4 DMA
* unlimited esc_status logging
* dshot: fix formatting
* dshot: add define for number of DMA channels to use
This allows individual boards to override the number of DShot channels
and hence avoid round robin capture of the RPM feedback.
* ARK: enable 4 DMA channels for DShot on 6X
* dshot: publish when all channels are updated
This slows down the ESC_STATUS publication in the case of round robin
capture. E.g. for 800 Hz output with one DMA channel, the ESC_STATUS is
now published at 200 Hz.
* dshot: avoid duplicate publications for bidir and telem
Instead of publishing both bidirectional dshot updates as well as
telemetry updates, we now combine the data from both streams, and
publish whenever we get RPM updates, as the latter arrives with higher
rate, e.g. 200 Hz with round robin, or faster otherwise.
When combining the data, we take RPM from bidirectional dshot, and the
rest from telemetry.
When we have only one of the two, either telemetry or bidirectional
dshot, we just publish that one.
* boards: add ark fpv and pi6x BOARD_DMA_NUM_DSHOT_CHANNELS
* dshot: turn off debug build
---------
Co-authored-by: Julian Oes <julian@oes.ch>
Co-authored-by: alexklimaj <alex@arkelectron.com>
* ark: v6x: disable net binary config, update default net config
* added back CONFIG_IPCFG_BINARY=y
---------
Co-authored-by: Alex Klimaj <alex@arkelectron.com>
192.168.0.x is often used by routers for WIFI/ethernet networks, and thus
can create conflicts.
This can happen for example if a companion is connected to the FMU via
ethernet and at the same time connects to a WIFI network as DHCP client.
* usb: Added parameter to enable always starting mavlink on USB.
Refactored cdcacm_init into a module and added a paramter to allow always starting mavlink on
USB, also added a paramter to choose the mode. The current default behavior is to wait and listen
for data on USB and auto-detect the protocol (mavlink, nsh, ublox). This results in the mavlink
stream not starting until something else on the mavlink network sends a packet first. The new
default behavior is to always start mavlink.
Added parameters
MAV_USB_ENABLE -- default 1 (always start mavlink on USB)
MAV_USE_MODE -- default 3 (onboard)
* added 3 retries for opening serial port in mavlink, removed sleep before sercon
* added DRIVERS_CDCACM_AUTOSTART to ark-v6x default.px4board
* added CONFIG_DRIVERS_CDCACM_AUTOSTART=y to default.px4board for boards with CONFIG_CDCACM in their nsh/defconfig
* format
* remove PGA460 from COMMON_DISTANCE_SENSOR to save flash
* remove LIS2MDL from COMMON_MAGNETOMETER to save flash
* disable CONFIG_DRIVERS_CDCACM_AUTOSTART for fmu-v5 protected.px4board
* moved and renamed parameters, removed mode logic in mavlink
* changed parameter names, added mode none
* remove parameters from mavlink
If the output is set to 0 then the FMU had this channel disabled/no function mapped
to it. In that case we do not want to suddenly start outputing failsafe or disarmed
signals.
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
