- Do not pull in PWM parameters when DISABLE_PARAMS_MODULE_SCOPING is TRUE since VOXL2 has no PWM nor any of the required timer_config files that go along with that
- Replace non-standard M_PI constants with PX4 defined M_PI_F constants
- Include missing header file for function hrt_absolute_time declaration
- Add new PX4_SOC_ARCH_ID for the VOXL2 board
* AirspeedSelector: use vehicle_air_data.rho for calculating groundspeed-wind CAS
Previously the vehicle_air_data.temperature and pressure was used, instead of the
density field directly.
Only makes a difference if there is an airspeed sensor connected to provide
the air temperature.
* AirspeedSelector: only safe estimated scale in param if airspeed is valid
* AirspeedSelector: remove 0.01 cliff for saving learned scale to param
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- first version of IMU driver for the VOXL 2 platform (Qurt)
- this is a customized version of the Invensense ICM42688P driver, it is currently in the VOXL 2 board directory
- new ROS2 platform in PX4 intended for creating configs that build and run entirely in ROS2
- PX4_CONFIG defaults to px4_ros2_default if no config specified and in a colcon workspace with ROS_VERSION=2
- currently doesn't do much other than allow you to build px4 msgs interface package
- WelfordMeanVector now computes covariance
- use Kahan summation for Welford mean (but continue using float32 for actual mean, etc)
- WelfordMean and WelfordMeanVector handle initial value and count roll over
- Welford mean count rollover at 16 bit max to prevent numerical issues and shift weight to newer samples
- sensors/vehicle_imu: update Welford mean usage (now simplified with resets removed)
- fix vehicle_imu_status accel var, now properly rotated with full covariance matrix
- gyro_calibration: update Welford mean usage
In review it was requested to have a different name for
manual_control_setpoint.z because of the adjusted range.
I started to investigate what naming is most intuitive and found
that most people recognize the stick axes as roll, pitch, yaw, throttle.
It comes at no surprise because other autopilots
and APIs seem to share this convention.
While changing the code I realized that even within the code base
the axes are usually assigned to a variable with that name or
have comments next to the assignment clarifying the axes
using these names.
To be consistent with all other axes of stick input and avoid future
rescaling confusion.
Note: for the MAVLink message 69 MANUAL_CONTROL it's using the full range
according to the message specs now [-1000,1000].
Completely detach the steering wheel logic from the yaw controller (beside using the
same manual stick input in a manual flight mode).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Log position setpoint reference of npfg
This commit logs the local position setpoint reference when using NPFG
* Address review comments
This commit address review comments from @tstastny
* Enable motor controls for fixed wing mode in tailsitters
This commit enable motor controls in fixed wing mode for tailsitters
This is needed for enabling quad tailsitters
* VTOL: differential thrust in FW: adapt params to be generic for all axes
Until now only suppoted on yaw axis. Not to be supported also on Roll and Pitch.
- VT_FW_DIFTHR_EN: make bitmask for all three axes independently. First bit is Yaw,
sucht that existing meaning of VT_FW_DIFTHR_EN doesn't change.
- VT_FW_DIFTHR_SC: rename to VT_FW_DIFTHR_S_Y and add same params for roll (_R) and
pitch (_P).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Integrate differential control bits to three axis control
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* Changed M_PI to M_PI_F in the matrix library since M_PI is non-standard.
* Added a new M_PI_PRECISE constant definition to px4_platform_common/defines.h to be
used in places when M_PI is desired but shouldn't be used because it is not C standard.
* Added the px4_platform_common/defines.h include to the matrix library math.hpp header to pull
in some non-standard M_PI constants and updated the test files to use those constants.
* Fixed PI constants in matrix helper test to prevent test failure
* Removed dprintf from perf library since it is only ever used with fd=1 (STDOUT) so moved to PX4_INFO_RAW instead. This helps with some platforms (e.g. Qurt) which have some Posix support but not full Posix support.
Peter van der Perk