* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
Add warning message in print_info() to alert users that CAN error counter
values may increase during the function call due to internal counter reading
implementation. Users should not fully trust these counters until the
underlying issue is fixed.
Co-authored-by: ljarvela <lasse.jarvela@iceye.com>
* feat: implement UAVCAN LED control for individual light control and assignment
* uavcan led: nit-picks from review
* uavcan led: reduce maximum number of lights
to avoid unused parameters
* uavcan led: simplify anticolision on check
* uavcan led: correctly map 8-bit RGB to rgb565
* Trim param name character arrays to 17
16 characters + \0 termination
* uavcan led: final nit-picks
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Guard the strncpy call with a null check to prevent undefined behavior
if the constructor is ever called with a null path pointer.
Fixes clang-analyzer-core.NonNullParamChecker diagnostic.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* update uavcan hardpoint: add ability to use it via mavlink cmd and during mission and removed send_command() dedicated for usage via mavlink console
* uavcan hardpoint: allow gripper ID 0
---------
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
* uavcan esc: remove unused includes
* uavcan arming_status: disarm when terminated
To stay consistent with kill.
* uavcan: publish armed during actuator tests to make it possible spinning motors
* feat: added driver for tmp102 temperature sensor
* style: removed new line
* style: adjusted date in header
* style: removed duplicated logging
* fix: moved start-up command from rc.board_sensors to rc.sensors
* style: used consexpr for expected config reg value
* feat: added retry logic to probe function
* style: added _ as prefix to global variable
* style: used make format
* fix: corrected temperature calculation
* fix: mask AL-bit in probe function
* style: removed header files from CMakeLists
* style: used correct english in comments
* refactor: return error right after failure
* style: moved init call to correct place
* fix: corrected temperature calculation (again)
* refactor: removed _curr_pr variable => always have to set PR to desired register on read
* fix: add multi logged topic
* driver: ist8310: add IST8310J device ID support and cross-axis compensation
IST8310J shares the same register map and initialization sequence as IST8310.
This change extends the existing IST8310 driver to:
- Accept the IST8310J device ID during probe and reset
- Load factory cross-axis calibration data from OTP
- Apply cross-axis compensation to raw magnetometer samples
The cross-axis compensation corrects factory axis misalignment only and
does not replace PX4 runtime magnetometer calibration.
Tested on Raspberry Pi using I2C with both IST8310 and IST8310J devices.
Signed-off-by: webbyeh <webbyeh@isentek.com>
* driver: ist8310: add IST8310J device ID support
IST8310J shares the same register map and initialization sequence as IST8310.
Factory cross-axis compensation support was evaluated but has been removed
in this revision due to flash size constraints on embedded targets. The
driver now focuses on device identification and stability, while relying on
the existing PX4 magnetometer calibration framework.
This commit also addresses review feedback by caching the WAI register value
to avoid redundant I2C reads during the reset wait state.
Tested on Raspberry Pi using I2C with both IST8310 and IST8310J devices.
Signed-off-by: webbyeh <webbyeh@isentek.com>
* Fix formatting issues in IST8310.cpp
---------
Signed-off-by: webbyeh <webbyeh@isentek.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* serial: add txSpaceAvailable function
* serial: txSpaceAvailable and bytesAvailable fixups
* msg: GpsDump: increase queue from 8 to 16 and replace instance with device_id
* lib: gnss: add RTCM parsing library. Generated by Claude Code.
* gps: fix RTCM injection to use inject-before-read pattern as before. Add RTCM parser to frame-align injection. Drain GpsInjectData uORB queue into RTCM parser buffer and then inject. Add GPS_UBX_PPK parameter to enable MSM7 output from the GPS module (rather than the default of MSM4) which is required for PPK workflows.
* gps: replace PX4_WARN with perf counters
* uavcannode: publishers: MovingBaselineData: publish all GpsInjectData updates during BroadcastAnyUpdates. Check and report data loss via uorb generationcounter. Only registerCallback outside of the loop.
* remove unnecessary include
* msg: GpsDump: increase queue from 8 to 16 and replace instance with device_id
* uavcan: gnss: MovingBaselineData subscriber for RTCM logging for PPK. Add uORB generation tracking to detect data loss on RTCM injection.
* add instance TODO
* Implemented driver for MCP23017
* fixed compatability with mcp23009. (naming of instantiated GPIO-Devices)
* removed some comments
* removed even more comments
* commented out instatntiation of driver since it will not be used with v6x
* removed last useless comments
* re-activated gpio_mcp23009 driver, removed useless comments and empty lines
* removed empty lines at the end of mcp23017.cpp
* removed empty line
* Implemented driver for MCP23017
* fixed compatability with mcp23009. (naming of instantiated GPIO-Devices)
* removed some comments
* removed even more comments
* commented out instatntiation of driver since it will not be used with v6x
* removed last useless comments
* re-activated gpio_mcp23009 driver, removed useless comments and empty lines
* removed empty lines at the end of mcp23017.cpp
* removed empty line
* basic working implementation
* first improved driver version with shared code base for MCP23009 & MCP23017 (built as state machine with sanity checks)
* removed unused imports
* changed module name from MCP to MCP230XX
* removed debug print statements
* adjusted auto start command of driver
* removed comments
* -added seperate main functions for both derivative modules (mcp23009 and mcp23017)
* compile common functions as shared library in src/lib/drivers
* fixed cleanup of modules
* ->unclean working version with shared common library
* used make format
* working & cleaned version
* -> Added CallbackHandler to be able to use multiple reading GPIO-expanders simultaneously
-> Removed old mcap23009 calls and pin registrations
-> Adjusted GpioIn.msg to contain MAX_INSTANCES
* ->removed unused imports
->used make format
* Fix: Re-enabled platform_mcp_gpio for accton-godwit, cuav, fmu-v5x
* Fix: enabled platform_mcp_gpio in px4/fmu-v5x
* added depency to fmu-v5x
* Fix: removed new lines
* Fix: fixed linker errors
* removed unused linkage against mcp-library
* Made mcp start calls consistent for fmu-v5x and fmu-v6x
* moved logging of comm errors to read/write function directly
* added perf_count for sanity_check
* removed error message
* ensured member variables follow naming convention
* added retries to probe function
* simplyfied state-logic
* add break to terminate loop early
* ensured clean state when register_gpios() fails
* add registered-flag to pins
* used path from top dir instead of relative path in CMakeLists
* used constexpr to set parameters instead of calculating them at runtime
* style: used make format
* fix: corrected i2c_bus assignment
* style: init input of callbackhandler to 0
* fix: mark pin as registered if successful
* style: made arguments const type
---------
Co-authored-by: Alexander Lerach <alexander@auterion.com>
ttechnick