If the measured voltage is more than 65v we need to split the voltage
over multiple cells in order to avoid overflowing the uint16. This is
according to the MAVLink spec.
Signed-off-by: Julian Oes <julian@oes.ch>
The extension fields need to be 0 by default according to the MAVLink
spec. This is because extensions are 0 by default and need to be 0 when
unknown/unused for backwards compatibility.
The patch also simplifies the flow slightly in that it doesn't create a
temporary array but just fills in the cell voltages directly.
Signed-off-by: Julian Oes <julian@oes.ch>
- simplify vehicle_status.arming_state down to just armed and disarmed
- ARMING_STATE_INIT doesn't matter
- ARMING_STATE_STANDBY is effectively pre_flight_checks_pass
- ARMING_STATE_STANDBY_ERROR not needed
- ARMING_STATE_SHUTDOWN effectively not used (all the poweroff/shutdown calls loop forever in place)
- ARMING_STATE_IN_AIR_RESTORE doesn't exist anymore
- collapse ArmStateMachine into commander
- all requests already go through Commander::arm() and Commander::dismarm()
- other minor changes
- VEHICLE_CMD_DO_FLIGHTTERMINATION undocumented (unused?) test command (param1 > 1.5f) removed
- switching to NAVIGATION_STATE_TERMINATION triggers parachute command centrally (only if armed)
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
It turns out that I had omitted implementing the gimbal_device_id which
is the component ID of the gimbal device that the gimbal manager (in
this case PX4) is responsible for.
Signed-off-by: Julian Oes <julian@oes.ch>
When requesting a message from a stream that is not active we start the
stream with interval=0 and call the request method once. For all streams
this works fine except the gps_global_origin. For this one the request method
is actually overidden to throttle down the rate and not just send out the message.
This will cause this message to never being sent on request if the stream
is not active by default.
- move EV yaw and EV position to new state machines
- EV yaw and EV pos now configured via EKF2_EV_CTRL (migrated from EKF2_AID_MASK)
- new EV position offset estimator to enable EV position while GPS position is active (no more EV pos delta fusion)
- yaw_align now strictly means north (no more rotate external vision aid mask)
- automatic switching between EV yaw, and yaw align north based on GPS quality
* GPS_RAW_INT: Only send no gps messages if gps has ever been present
* GPS2_RAW: Keep in sync with GPS_RAW_INT
Signed-off-by: Marcell Rausch <marcell@auterion.com>
In review it was requested to have a different name for
manual_control_setpoint.z because of the adjusted range.
I started to investigate what naming is most intuitive and found
that most people recognize the stick axes as roll, pitch, yaw, throttle.
It comes at no surprise because other autopilots
and APIs seem to share this convention.
While changing the code I realized that even within the code base
the axes are usually assigned to a variable with that name or
have comments next to the assignment clarifying the axes
using these names.
- this is a precaution to eliminate the possibility of getting stuck in
a loop trying to keep up with a high rate publication that could be
coming from a higher priority task
- replace float32[21] URT covariances with smaller dedicated position/velocity/orientation variances (the crossterms are unused, awkward, and relatively costly)
- these are easier to casually inspect and more representative of what's actually being used currently and reduces the size of vehicle_odometry_s quite a bit
- ekf2: add new helper to get roll/pitch/yaw covariances
- mavlink: receiver ODOMETRY handle more frame types for both pose (MAV_FRAME_LOCAL_NED, MAV_FRAME_LOCAL_ENU, MAV_FRAME_LOCAL_FRD, MAV_FRAME_LOCAL_FLU) and velocity (MAV_FRAME_LOCAL_NED, MAV_FRAME_LOCAL_ENU, MAV_FRAME_LOCAL_FRD, MAV_FRAME_LOCAL_FLU, MAV_FRAME_BODY_FRD)
- mavlink: delete unused ATT_POS_MOCAP stream (this is just a passthrough)
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
- all sources of optical flow publish sensor_optical_flow
- sensor_optical_flow is aggregated by the sensors module, aligned with integrated gyro, and published as vehicle_optical_flow
Co-authored-by: alexklimaj <alex@arkelectron.com>
