nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
The control params (eg min/max pitch) are used before they are
correctly set by TECS::update(). While this is an issue we should fix,
it also doesn't hurt to set them to more reasobale values (eg 30° limit).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Even if there is some horizontal motion, a passing check should be
accepted as the terrain can be flat. However, the vehicle must not be
moving horizontally to invalidate the consistency as a change in terrain
can make the kinematic check temporarily fail.
The param is not really required anymore with the actuator
configuration. Also, when it is set to 0, RC doesn't work for some
boards which would be nice to avoid.
Signed-off-by: Julian Oes <julian@oes.ch>
During a round corner the L1 distance calculation
was only done in 2D and the z-axis coordinate
was directly coming from the next waypoint.
This lead to an unpredictable altitude profile
between two waypoints. Sometimes almost all
altitude difference was already covered during
the turn instead of going diagonally.
This sets the src/drivers/gps/devices submodule to the latest
release/1.14 branch. This fixes a potential issue with the Unicore M10
GPS driver, making sure the AGRICA message is requested.
Signed-off-by: Julian Oes <julian@oes.ch>
This switches from the horribly intertwined ringbuffer implementation to
the new VariableLengthRingbuffer implementation.
By ditching the previous implementation, we fix MAVLink message
forwarding, which didn't work reliably. The reason it didn't work is
that multiple mavlink messages could be added but only one of them was
sent out because the buffer didn't keep track of the messages properly
and only read the first one.
Signed-off-by: Julian Oes <julian@oes.ch>
This adds a reusable class for a FIFO ringbuffer that accepts variable
length packets. It is using the Ringbuffer class internally.
Signed-off-by: Julian Oes <julian@oes.ch>
During transition to FF, only allow update thrust axis up to 45° as with a high tilt angle
the effectiveness of the thrust axis in z is apporaching 0, and by that is increasing
the motor output to max.
Transition to HF: disable thrust axis tilting, and assume motors are vertical. This is to avoid
a thrust spike when the transition is initiated (as then the tilt is fully forward).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
The length check for unknown packets did not include PACKET_SIZE_TYPE_SIZE
and CRC_SIZE, and hence working_index could overflow CRSF_MAX_PACKET_LEN,
triggering invalid memory access further down in QueueBuffer_PeekBuffer.
Also the working_segment_size was wrong for unknown packets.
Credits for finding this go to @Pwn9uin.
A setpoint of type IDLE can be published by Navigator without a valid position,
and should be handled in the auto function in FW_POSCTRL_MODE_AUTO. If it wouldn't be
handled there the controller would switch to mode FW_POSCTRL_MODE_OTHER, in which case
no attitude setpoint is published and the lower controllers would be stuck with the
last published value (incl. thrust).
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Positon Controller: set altitude_ref to 0 if not provided by GPS
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Positon Controller: set lat/lon reference to 0 if not provided in local_position
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- force initialize takeoff airspeed setpoint at start of takeoff modes
- force set airspeed constraints if slewed value is out of bounds
- always slew airspeed setpoints as long as inside constraints
- move target airspeed setpoint calculation into mode specific logic regions (hand vs runway)
when we're in a takeoff situation, we only want to adapt the airspeed to
avoid accelerated stall due to load factor changes. Disable othre logic
like minimum ground speed, wind based adaption and airspeed slew rating.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
