* refactor(mixer_module): change MixingOutput to use float outputs
MixingOutput now passes float values to output drivers instead of
uint16_t. This removes the need for the 8192 offset encoding and
allows reversible motors to receive negative values directly.
* fix(mixer_module): fix float safety issues
-EscClient and voxl2_io: replace outputs[i] with fabs(outputs[i]) > 0.fto fix compilation issues
-GZMixingInterface: add explicit double cast to prevent compilation error
-PWMSim: replaced unit16 cast with lroundf given that now motors outputs can be negative and casting a negative float to unit16 is undefinder behaviour
-mixer_module: same fix of PWM (unit126 cast on negative float is undefined behaviour)
* refactor(mixer_module): float rounding suggestions
* fix(pwm_sim): fix inverted disarmed condition
* fix(mixer_module): more float rounding improvements
* fix(mixer_module_tests): use casting method which are now in drivers for rounding tests
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
dshot: fix motor test on CANnode
Also includes fixes for the DShot driver since stop_outputs is removed. The esc info command has been removed because it doesn't work with AM32, can only be used via command line, and complicates the driver
This allows to consistently define:
Motor stopped - disarmed PWM
Motor idling - minimum PWM
Motor at full thrust - maximum PWM
Any allocation can then distinctly decide if
a motor should be running or not depending
on the context and also explicitly command that.
This fixes an invalid memory access when exiting the module:
exit_and_cleanup destroys the object, but lock_guard is destructed after
and accesses the lock.
- fixes the deadlock in px4io ioctl mixer reset
- px4io Run() locks (CDev semaphore)
- mixer load goes through px4io ioctl MIXERIOCRESET which calls MixingOutput::resetMixerThreadSafe()
- MixingOutput::resetMixerThreadSafe() stores a Command::Type::resetMixer command in an atomic variable, schedules a work queue cycle, then sleep spins until the command is cleared
- the execution of the cycle eventually calls back into PX4IO::updateOutputs(), which tries to lock (and waits forever)
and remove the possibility to set min > max to reverse.
Initially the idea was to add the checkbox on the UI side, to avoid adding
another param, but I don't think I'll go through the extra effort on the
QGC side.
- parameter updates can be quite expensive because they trigger nearly all modules to reload all of their parameters immediately
- limit modules from updating faster than once per second
- split out switches from manual_control_setpoint into new message manual_control_switches
- manual_control_switches published at minimal rate (~ 1 Hz) or immediately on change
- simple switch debounce in rc_update (2 consecutive identical decodes required)
- manual_control_switches logged at full rate rather than sampled at (5-10% of messages logged)
- manual_control_setpoint publish at minimal rate unless changing
- commander handle landing gear switch for manual modes
- processing of mode_slot and mode_switch is now split so we only do one or the other (not both)
- a future step will be to finally drop mode_switch and accompanying switches entirely
Co-authored-by: Matthias Grob <maetugr@gmail.com>
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
The threads running commands for clients through the Posix daemon used
to write to a char buffer through snprintf (etc.) which was then written
directly to the file descriptor, whereas in the other case printf
(etc.) was used to write to stdout (FILE*). Both versions used some
macro's and repeated code to have the same output.
This change unifies these two cases by using a FILE* in both cases. The
(line) buffering is done by the standard C library's implementation
(just like with stdout), and px4_log.c now uses the same code in all
cases (using fprintf, etc.) for printing (colored) output.
